Search Documents

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By Arnold J. J

The design of a coal preparation plant using bore core data cannot be discussed without some reference to the wider considerations of design. A thorough knowledge of coal preparation processes and processors as well as ancillary equipment is essential if the coal properties determined from bore cores, are to be fully utilised. Whilst generalised information of processes is available from a wide range of publications and equipment suppliers for the intending plant designer, local operational experience must be taken into account where there are similarities. However it would be wrong to assume that satisfactory plant design can be achieved merely be repeating previous design parameters. A detailed examination of bore cores used in conjunction with well proven design 'criteria will identify important differences in design parameters without which efficient and economic plant/sectional sizing cannot be achieved.

Jan 1, 1977

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

By S F. Wang, J J. Yin

Dust pollution poses a persistent challenge within mining processes, giving rise to a spectrum of concerns, including occupational diseases, mechanical degradation, diminished visibility, and the potential for dust explosion incidents. Existing dust detection and monitoring methodologies face limitations, including insufficient measurement accuracy and intricate processing procedures. Consequently, a comprehensive identification and evaluation system rooted in image processing technology is proposed to facilitate real-time measurements of dust pollution in mining worksites. The study primarily employs grey scale average and fractal dimensions to characterise particle features evident in collected dust images. As a result, the data processing platform can dynamically process data and present dust pollution conditions. Notably, this research integrates the monitoring and assessment of dust pollution with the systematic adjustment of mining parameters, ventilation parameters, and strategies for dust reduction. Through statistical analysis of dust concentration and particle size during mining processes, rock properties such as components and cuttability can inform mining parameters. This information, in turn, guides detailed excavation strategies, including cutterhead speeds, torque, and excavation speed. Similarly, analysing dust characteristics derived from images is a valuable resource for gaining deeper insights into the efficacy of implemented ventilation strategies. By harnessing vision-based information detailing dust concentration and distribution, a wealth of direct guidance becomes available for refining ventilation parameters. This encompasses crucial aspects such as the selection of appropriate ventilation systems tailored to the specific mining environment and the optimisation of operational conditions for ventilation fans. Additionally, the detailed information derived from the visual data allows for strategic decisions on factors like the spatial arrangement of ventilation outlets and the calibration of airflow rates. Moreover, precise choices for dust reduction measures and parameters can be made based on the prevailing dust conditions. Upon real-time monitoring of dust pollution using the proposed method, corresponding measures such as spraying and foaming can be promptly implemented. Crucial parameters, such as spray angles and volume, are integral to these application processes. In essence, the proposed method assumes a pivotal role in not only dust monitoring but also the formulation of preventative and control measures within mining processes.

Sep 1, 2024

In early-1989, subsidence due to voids at the top of previously filled stopes and stopes awaiting filling,began to threaten the 15 level fill conveyor horizon. This together with the need to maintain production targets meant that a method was required to significantly increase fill placement.Alternative methods of placing dry fill underground were investigated. One option was to drill 200 mm boreholes from surface directly into stopes 600 - 800 metres underground. A drilling program was successfully undertaken, and resulted in the placement of more than 800 000 tonnes of dry aggregate fill via four boreholes.This paper details the drilling program undertaken and discusses the difficulties encountered, the fill placement system and the project costs.

Jan 1, 1992

By R LEATHAM

Long hole drilling underground has come a long way since 'down the hole' surface drills were first taken underground. The underground miners have progressively developed the use of long hole stope drilling from the 'quarry blast' to a precise and selective removal of ore while leaving the remaining structure as undamaged as possible. To reach this position has involved the development of equipment and explosives to give the desired results. This paper reviews some aspects of long hole stope production drilling.

Jan 1, 1992

By M Yahyaei, P Knights, M S. Kizil, J Qu

Digital Twins (DTs) are transforming business operations across many industries through their accurate representations of physical entities enabled by IoT technologies.

Sep 1, 2024

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

Two separate mine rehabilitation programmes carried out by Australian Consolidated Industries Limited (A.C.I.) in South Australia at Normanville and Port Lawler are discussed. Emphasis is given to the methods used, the results achieved and to possible future improvements.

Jan 1, 1976

By T Perera, B Fan, S Thang, T Hsia

Minerals are valuable resources and critical elements for a broad range of biological and technological applications, including technological developments to improve energy efficiency and the global movement to promote a low-carbon economy. However, in order to extract these critical metals, large amounts of waste and toxic chemicals are generated, as well as the use of high energy and large amounts of water consumption. Froth flotation is one of the most commonly used processes to separate and collect high-value minerals, but it still has some limitations, including low flotation efficiency performances using existing collectors and other reagents. Therefore, there is an urgent need to design and develop new metal-specific collectors to more efficiently separate and recover valuable minerals and to allow bulk water recovery from flocculated tailings. In this research, we propose to use our newly designed and synthesised novel collectors derived from a type of vitamin E (α-tocopherol), a relatively inexpensive and non-toxic natural molecule. As a potential collector-building block, α-tocopherol has a long hydrophobic carbon chain that facilitates the attachment to air bubbles during the froth flotation process. In addition, the phenol group of this molecule can be easily modified to incorporate various functional groups for targeting different types of minerals. Furthermore, α-tocopherol can be converted into a monomer for polymerisation by the reversible addition-fragmentation chain-transfer (RAFT) process, which can provide us with polymer based-collectors with high precision control of molecular weight and architecture. So far, small-scale qualitative experiments on α-tocopherol-based collectors have been performed with good results, which indicates the feasibility of these compounds as novel collectors for improved froth flotation processes.

Aug 24, 2022

By J Vann

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and û importantly û metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These ægeometallurgical variablesÆ drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many ætraditionalÆ (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007

Supergene enrichment of ilmenite occurs through a complex series of reactions with initial oxidation and hydration followed by leaching and dehydration. Lateritization appears to be associated with the early phase of the supergene process and if ilmenite grains are encased in iron oxides no further alteration proceeds.

Jan 1, 1986

By Billingham R

The Department of Mines Tasmania employs a Drilling Section for specialised drilling re- quired by government and semi-government bodies. The section has a complement of nine crews oper- ating auger, cable tool, rotary and diamond drilling plants. For some years the Department has been involved in site investigation drilling of the Derwent River. The experience gained indicated that drilling methods should be altered. In 1976 an urgent programme was requested and the opportunity was taken to solve many problems associated with previous investigations. Equipment and methods are discussed in detail. The improved technique contributed to the suc- cessful completion of the Phase 1 site investi- Gation.

Jan 1, 1977

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

Maps of mineral grade used to assess mineral reserves are most commonly generated using one of the many estimation methods available such as inverse distance weighting or ordinary kriging. Most such maps incorporate a degree of spatial smoothing which is an integral part of the averaging process. In deposits with highly variable grade which include many gold deposits, this smoothing can mask the detailed geometry of the mineralization at the economic cutoff grades being considered. In underground mining, a knowledge of this geometry is important in the choice of mining method and thus in the assessment of the minable reserves.The method of conditional simulation in geostatistics can be used to generate maps of grade which reflect the actual spatial variability of grade as measured through the variograms of the drill hole data. Simulated maps can provide a number of equiprobable images of the mineralization geometry from which a more appropriate mining model of the mineralization can be developed. Multiple simulations can also be used to assess the uncertainty existing in the current knowledge of the reserves.

Jan 1, 1990

The relationship between the permeability of coal to a mixture of methane and carbon dioxide, and the permeability to methane and carbon dioxide separately is described in this paper, along with the analysis of the differences in permeabilities of coal to methane and carbon dioxide.

Jan 1, 1989

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

By T P. Hynes

Submarine tailings disposal is conceptually an attractive option for managing reactive mine wastes in coastal regions by virtue of reduced sulfide oxidation under a water cover and no infrastructure to maintain after mine closure. However, the lack of detailed knowledge of metal leaching, dispersal of fine tailings and biological impacts in the marine environment has led to no operating permits currently in effect in Canada. Detailed chemical and ecotoxicological assessments at two historic copper mine sites (Little Bay and Tilt Cove) in the north coast of Newfoundland with tailings disposed in an estuarine to shallow (=100 m) marine environment have demonstrated reduced reactivity of sulfidic tailings when submerged under water. Only non-acute toxicity is detected in biota inhabiting the immediate vicinity (A review of another historic shallow marine tailings operation in the southern tip of Vancouver Island (Jordon River) with a high-energy setting also reveals problems with unconfined tailings dispersal and temporal biological impacts. Documented studies at two deeper (140 - 360 m) marine tailings disposal operations at the northern tip of Vancouver Island (Island Copper) and northwestern coast of British Columbia (Kitsault) again illustrate imperfect predictions of tailings re-suspension and dispersal. At these sites, bioaccumulation of tailings-derived metals appears to be minimal. There is evidence of rapid re-colonisation of the tailings surface by benthos but of different species than the original population. Integrating these observations with reported metal fluxes and biological diversity associated with submarine hydrothermal vents, the risks and benefits of deep-sea (>1 km) tailings disposal are discussed. To determine if submarine tailings disposal in deep, confined basins on the seafloor is environmentally friendly, detailed multi-disciplinary research incorporating physical, chemical, biological and toxicological components will be indispensable.

Jan 1, 2003

By Li T

Mining of the southern 1900 copper Orebody presented a challenge due to the complex geology, geometry and simultaneous extraction of the nearby lead/zinc/silver orebody. An integrated and co-operative approach was adopted, involving geology, geomechanics, mine planning and production personnel. Successful extraction of the first 1900 Orebody stope, T496, together with the extraction of the first two lead/zinc/silver panel stopes in the immediate hangingwall of the 1900 Orebody stope was achieved as a result of this approach.

Jan 1, 1995

By N McIntyre, R Trancoso, N Bulovic

Mining is essential for facilitating human development particularly as demand for critical minerals grows. However, over the mine life cycle, the environment is permanently changed. Once mining ceases, mine-affected land can leave significant legacy issues on the surrounding environment if not managed. Therefore, mine closure planning is critical. Mine closure occurs over large scales often with the aim of recreating resilient ecosystems over mined landscapes with mitigated negative impacts. The natural state of the landscape and the environmental risks over planning time-scales are largely driven by climate. Climate change is expected to impact different parts of the post-mining landscape, from stable landform design (soil erosion mitigation) to revegetation efforts and pit lake management. Consequently, mine closure plans may need to account for a non-stationary and uncertain future climate, that may be both different to the current climate and evolve during the mine life and post-closure. Here a new data-based approach is presented for incorporating climate change projections in mine closure planning, based on the recently released Coupled Model Intercomparison Project phase 6 (CMIP6) climate data used in the latest Intergovernmental Panel on Climate Change (IPCC) assessment report. The approach: (i) characterises closure-related attributes of the future climate, and (ii) identifies the amount (and direction) of change expected to occur, and its uncertainty, focusing on five metrics for demonstrative purposes and initially describing changes in erosive potential below. This provides information on the type of future environment (ie the changing baseline) that mine closure should plan towards, and identifies rehabilitation options that may be susceptible to increased risks from climate change.

Aug 2, 2023