Search Documents

By S Meffre, A E. Fallick, K Zaw, I T. Graham, G Giuliani

Dispersed gem corundum is mined from placers, commonly from basalt fields, as occurs along eastern Australian and Asian continental margins. New laser ablation inductively coupled plasma mass spectrometry analysis (LA-ICP-MS) of Australian corundum allows genetic distinctions among these suites and gives clues to their primary lithospheric sources prior to basaltic delivery. Bimodal corundum suites at Barrington Tops, Cudgegong-Gulgong-Macquarie River and Yarrowitch, New South Wales (NSW), include lower Ga, higher Mg æmetamorphicÆ and higher Ga, lower Mg æmagmaticÆ groups. The Barrington Tops æmetamorphicÆ corundum is more Fe-rich (av 4500 - 7100 ppm) than Cudgegong- Macquarie River equivalents (av Fe 1800 - 2100 ppm). Yarrowitch corundum is relatively low in Fe, Ti and Cr. Along with other eastern Australian data (north-east Tasmania; New England, NSW) and from gem fields elsewhere, the combined trace element and O isotope data, reveal considerable geographic and genetic variations within the corundum suites. A few corundum groups contain noticeable Be, Sn, Ta, Nb, a particular genetic message that also precludes easy distinction of treated corundum in the gem trade. Expanding geochemical, inclusion and geochronological data on gem corundum hold promise for characterising derivative gem corundum on both geographic and genetic features.

Jan 1, 2008

By Lightfoot BW, Wand PD, Towne DV

Sampling and e.m.f. probes were used in the liquid flow from the blast furnace and in the forehearth to evaluate the performance of the copper smelting system at E.R. & S. Significant variations in temperature, oxygen potential and copper content with slag depth and with position in the forehearth indicated that convective currents were causing considerable stirring in the forehearth. This was attributed to temperature fluctuations in the stream from the blast furnace, which resulted in colder slag being underlain by hotter matte. Tracer tests in the feed to the smelter and in the feed to the forehearth revealed considerable holdup of material in the plant and confirmed that the forehearth involved small scale turbulence but little large scale mixing. The results indicated that the copper content of slag continuously tapped from the forehearth could be lowered by at least 0.15% if better settling could be achieved and means of attaining this are discussed. As part of the investigation the recovery of copper from spent refractory bricks recycled through the smelter was evaluated. It was found that the recovery was high but it seems likely that the brick material is partly responsible for a build up of solid material in the forehearth.

Jan 1, 1981

I know the theme of the Congress is "The 21st Century - Mining for Mankind" but I hope you will understand why my address touches upon some near-term issues as well. With the world oil market the way it is at present, "the long term" seems to be next week and no one is even sure what will happen tomorrow! So I am going to take a little licence with the theme of the Congress and talk about some fundamental issues that have much to do with the current uncertainties. The ways in which these issues are resolved and the role governments elect to play in the next few years will determine both the shape of the petroleum industry in the 1990s and beyond and the success with which we can confront a growing and inevitable future dependence on OPEC oil resources. But just in case you are not familiar with what has been happening in the petroleum industry recently and why the future seems more uncertain than ever, let me show you the gyrations in oil prices over the past 13 years, and remember that it is only another 13 years or so years to the 21st Century.

Jan 1, 1986

The title of my address today 'An Environment for Mineral Development' is a play on words, but I wish to use the meaning of the word environment in the broadest possible context to comment on those factors that control mineral development in New Zealand today. Of prime importance, let us consider the current economic environment in which New Zealanders live and work, as individuals and communities, and as a trading nation. It is the expanding growth requirements of the emerging nations and the interactive economic forces of our international trading partners and competitors, that dictates New Zealand's economic environment and thus the priority to develop its natural resources. As an itinerant New Zealander who has kept a watching brief over the economic environment in New Zealand over the last 30 years, I say, without prejudice, that I am concerned to have seen New Zealand's external and internal trading position deteriorate so rapidly in the last decade. I am concerned that a significant proportion of the population has been extremely slow to realize that with the creation of the European Economic Community, in the late 1950s, and following the first OPEC oil crisis in 1973, New Zealand in a corporate sense came close to technical bankruptcy.

Jan 1, 1985

By Carroll D. A

The mining and minerals industry has had and will undoubtedly continue to have a considerable impact on the development of this State. For the first 60 years of its history the colony of Western Australia made slow progress; its population in 1889 being only 43,000. However, as a-result of discovering gold at Coolgardie and Kalgoorlie the Eastern Goldfields alone had a population of 25,000 by 1897. The income generated by the gold mining industry allowed the Premier of the day, Sir John Forrest, and his Government to support the proposal put forward by the State's Engineer in Chief, C.Y. O'Connor, to construct a pipeline to carry water from the Darling Ranges to Kalgoorlie ; a distance of 600 kilometres. The demand for people knowledgeable in the science and art of mineral exploitation also prompted the State Government to establish a School of Mines in the Goldfields in 1902, where it has remained ever since. The gold mines of this region have been a major source of employment for over 70 years and there is no doubt of the fact that their continued prosperity minimised the effect of the world recession on Western Australia in the 1930's.

Jan 1, 1979

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

By S Hapugoda, Y Tang, L Lu

The steel industry is one of the global leading CO2 emitters, accounting for approximately 7 per cent of global anthropogenic CO2 emissions. In 2022, the world produced 1878.5 Mt of crude steel. About 70.8 per cent of the world’s crude steel was produced by integrated steel mills through the blast furnace and basic oxygen furnace (BF-BOF) process, while the remainder was produced largely by mini mills using electrical arc furnaces (EAF). Compared with gas-based DRI and scrap-based EAF processes, the direct CO2 emissions from the BF-BOF process and the coal based DRI and EAF process are significantly more, as both the processes rely heavily on fossil fuels, such as coke and pulverised coal, to provide energy and reduce iron oxides. Hydrogen is very reactive and reduces iron oxides to metallic iron without generating CO2. Therefore, substitution of hydrogen for fossil fuels in these processes presents a good opportunity to significantly decarbonise the steel industry. This paper will first discuss the thermodynamic and kinetic characteristics of hydrogen and carbothermic reductions of iron oxides and then examine the behaviours of different ore types present in Australia iron ores during hydrogen reduction.

Sep 18, 2023

By R Grogan

The Ungay-Malabago polymetallic deposit, currently owned by Lafayette Mining, is located on the eastern end of the island of Rapu-Rapu which lies east of the city of Legazpi in the Philippines. The island is sparsely populated and has largely been deforested by extensive logging some 30-40 years ago.The deposit is situated on a plateau some 200 m asl and lies about one kilometre inland from the coast. The site topography is difficult with minimal flat areas for plant facilities. The region around Legazpi is subject to volcanic activity and though the island is not affected it is in a seismic zone. There is no other mining or other industrial activity on the island, the local inhabitants being engaged in subsistence farming and fishing. These activities place a high level of responsibility on the mine operator with regard to the environment and the provision of employment and training to the local inhabitants. Although no previous mining was carried out at Ungay, shallow pit mining for high-grade direct smeltable copper ore has occurred during the mid-1900s in an area, known as Hixbar, some 2 km west of the deposit This area is currently being explored by Lafayette.

Jan 1, 2002

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

By Oversby B, Wellman P, Wyborn D, McPhie J, MacKenzie D

The Bureau of Mineral Resources (BMR) and the Queensland Mines Department are engaged in integrated regional- and deposit-scale studies in the Burdekin Falls-"Conway" area, about 100km southeast of Charters Towers (Fig. 1). The regional work augments recent mapping in the Mount Coolon area farther south (Hutton et al., in prep.). These studies are aimed at improving understanding of gold mineralisation and its geological setting in the Drurunond Basin and associated rocks. Knowledge of the regional stratigraphic- structural framework and setting of mineralisation has until now been based on investigations dating from the early to mid 1960's (mainly Bowen 1:250 000 Sheet; e.g. Paine et al., 1974; Wyatt et al., 1971), and on regional syntheses (Olgers, 1972; Levingston, 1981). Some recently explored epithermal gold occurrences in the region have been interpreted on the basis of this early work as being hosted by the Late Carboniferous Bulgonunna Volcanics. The objective of our field research was to refine the regional geology, paying particular attention to the Bulgonunna Volcanics. The results summarised here indicate that unnamed Devonian-Carboniferous volcanics (DCv) of the northern Drummond Basin and mid to late Palaeozoic granitoids are much more extensive, and the Bulgonunna Volcanics much less so, than was previously recognised.

Jan 1, 1989

Study on Preparation and Gel Performance of High Purity Montmorillonite In order to research the colloidal and thixotropic performance of the inorganic gel prepared by high purity montmorillonite, this study uses the moderate grade bentonite ores from Weifang (China) as raw material. Two-stage hydrocyclone classification was applied to obtain the high purity montmorillonite with its content of 94.8 per cent. In contrast to other methods of montmorillonite purification, two-stage purification by hydroclone has the advantages of larger throughput and easily achieving auto-control in industry, and purified products with different montmorillonite content can be obtained by this method. And then the inorganic gel was prepared by the prepared high purity montmorillonite and its colloidal and thixotropic performances by measuring the flowability and thixotropy were further studies. Research results show that the inorganic gel has plastic body liquidity, the viscosity decreases with the increase of the shear rate, the static and dynamic shearing stress values are 33.98 Pa and 91.89 Pa, respectively, and the thixotropic value is 95.2 dyne+s/cm2, which indicates that it has preferable colloidal and thixotropic performance. Montmorillonite inorganic gel prepared by bentonite with high montmorillonite content and low-layer charge has better gel performance.

Sep 13, 2010

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

By Williams P, Hender A

The 1980s witnessed a major revolution in the application of airborne geophysics to mineral exploration. The now commonplace term `high resolution aeromagnetics' (HRA) evolved from advances in survey specifications, instrumentation, data processing and imaging techniques which greatly improved the quality and geological information content of the final maps. Although initially HRA was successfully applied in `hard rock' basement terrains, eg the Archaean Yilgarn Craton of Western Australia, the technique along with the radiometric and electromagnetic techniques is now gaining wide acceptance in all geological terrains including inaccessible sedimentary rock dominated mountain belts such as New Guinea for mineral and petroleum exploration. It is also being used in more and more diverse roles away from exploration, such as environmental monitoring. The main reason for this acceptance is of course the very cost-effective surface and sub-surface mapping capabilities of the various airborne techniques. Although the three main techniques (magnetic, radiometric and electromagnetic) have been in use for some time, they are continuously being improved. Recent developments include: ò better navigational positioning using real-time GPS systems (Geographic Positioning Systems) such as Picodas Navigation Systen (PNAV); ò the use of magnetic gradiometer systems; ò improved sensitivity and sampling rate of magnetometers; ò increased use of ultra detailed low level (

Jan 1, 1996

By Salehi M. R

Although inherent mineral matter appears to have no effect of the reflectivity of inertinite in the reflecting light microscope, it has a marked effect on the grey levels resulting from the backscattered electron response in the scanning electron microscope. Inertinite with a high inherent mineral matter content has a high grey level response but not as high as that of mineral matter. The highest grey level response is with inertodetrinite which at times could be mistaken for mineral matter. Fusinite has a higher grey level response than semi-fusinite. The backscattered electron grey level response corresponds to average atomic number and hence approximately to density. If a porous structure develops and becomes filled with mineral matter such as S, Cl, Ca, Si, and Al the grey level will be higher. Micrinite has an unusual response in that it behaves like an exinite maceral in the SEM rather than an inertinite maceral. It either has a low grey level when relatively free of inherent mineral matter, or a low grey level background with high level granules corresponding to Si and Al dominantly. Similar structures have been found in exsudatinite and resinite. It is thought that micrinite results from the migration of hydrocarbons out of exinite giving a porous structure which usually accommodates inorganic matter.

Jan 1, 1991

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

By Grieve BL

For a blast to be successful both heave and fragmentation must be satisfactory. Amongst the major factors influencing blasting are rock properties. This paper considers the effect of rock density on fragmentation and heave and how better results can be achieved in dense ore. Patterns which increase the heave and give better fragmentation are examined and the application of theory to the blasting of the Dales Gorge Haematite, density 4.2 - 4.5 t.m.,3 is then discussed. The drilling of staggered patterns instead of square patterns and a shallower 'V' initiation system has given better heave and fragmentation. This practice has re- duced backbreak and improved toe conditions; these factors have resulted in increased load ing rates. There has been an increase in the lump/fine ratio which is consistent with the theory although other factors such as ground conditions could have contributed.

Jan 1, 1978

By Orid A

A fast, non-contact technique for measuring sizes of rock fragments on a conveyor belt is presented. An image processing technique called active stereopsis is used which makes use of a light stripe projected on to the surface of the fragments on the conveyor belt. A CCD TV camera is used to capture the shape of the distorted light stripe. the video image of this shape is then processed by a computer program so that the 3D profile of the surface can be obtained by triangulation. The sizes of the rock fragments are then calculated from this profile. The speed of the technique is improved by calibrating the light stripe system before measurement begins so that the profile of the fragment surface can then be measured using simple geometry. The technique is fast and highly parallel so that it is able to operate in real time.

Jan 1, 1990

By Richards AB

This paper describes the ENVIB software system, which has been developed in a menu-driven form to aid in the monitoring and assess- ment of vibration caused by routine blasting operations and for research and development projects. The paper gives an outline of the capabilities of the system by means of screen-dumps and a general descriptive commentary. Technical notes have been added where appropriate to further describe the system. The ENVIB system covers: I . Analysis of blast vibration results, and preparation of graphs and tables for control and estimation purposes. 2. Effects of atmospheric conditions and air vibration propagation. 3. Real-time acquisition and analysis of analogue blast vibration sig- nals directly from transducer equipment or from FM tapes. 4. Analysis of digital files on floppy disc or transferred via the serial port from blast monitoring equipment. 5. Transfer function calculation for structure response studies.

Jan 1, 1988