Search Documents

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

Fluid inclusions and sulfur isotopic compositions were studied in a possible extension of the Toyoha polymetallic vein deposit. The objective of this work was to gain a better understanding of the ore depositional conditions, sources of ore constituents, and distribution of mineralizing fluid in the region. Fluid inclusions in sphalerite and quartz show that most homogenization temperatures range between 190¦ and 290¦C. Most salinities range from 0.0 to 3.4 wt per cent NaCl equiv. Sulfur isotopic compositions of ore minerals (pyrite, sphalerite and galena), determined by a conventional technique, range between 1.3 and 7.7 per mil. The mineralizing fluids were characterized by relatively low and various temperatures and low to moderate salinities compared to those at the southeast region of the main ore bodies (Izumo and Shinano veins) where rare elements such as tin, tungsten and indium occurred. Obtained temperatures and salinities were attributed to the mixing of hydrothermal fluids with groundwater. Sulfur isotopic data suggest sulfide sulfur was of magmatic origin. Isotopic temperatures, estimated from the isotopic fractionation factor between sphalerite and coexisting galena, are between 195¦ and 322¦C. The temperatures are only consistent with fluid inclusion homogenization temperatures in sphalerite or coexisting quartz when sphalerite was a honey-yellow coarse crystal lacking conspicuous colored growth bands. This suggests the detailed classification of mineral pairs growth textures will be necessary for precise in situ measurements to obtain reasonable eothermometric results.

Jan 1, 2002

The End of the Line for Roadway Development By Michael Kelly, CSIRO Exploration & Mining Michael Kelly highlighted that roadway development performance remains one of the threats to expansion of Australia underground coal exports to the growing Asian market. In a recent industry study, automation was highlighted as one of seven strategies for roadway development improvement. Growing Asian markets The expansion of the Asian coal market is a long term driver for expansion of the underground coal industry in Australia - if significant productivity improvements are made. Imports of steaming coal by Asian APEC members are predicted to rise by from 150 MT to 190 MT. Australia is one of the few countries which has a potential capacity larger than predicted internal needs. Predictions are for exports of black steaming coal from Australia to increase from 50.3 MT in 1992 to 106.3 MT in 2010. To meet this prediction, an investment of $10.7 billion (in 1992 dollars) will have to be made in mining and transport facilities. This is equivalent to the opening of a major new mine each year until 2010. Many of these mines will be underground operations. However, much of Australia's capacity to respond to increased Asian demand will depend on its ability to develop underground technologies and improve productivity. The inability to make sustained improvements in roadway development rates has to date been one of the main reasons why new underground projects have failed to deliver the expected returns.

Jan 1, 1997

By Travis G. A

The Mons Cupri Cu-Pb-Zn deposit is situated within a complex Archaean volcanic sequence dominated by rhyolitic fragmental rocks. This sequence is underlain by a 150 m group of rhyolitic ash flow tuffs with minor conglomerate and sandstone, and is overlain by approximately 180 m of dacite and andesite flows. The Mons Cupri sequence itself consists of several elongate or circular rhyolite domes, flanked by rhyolitic fragmental rocks ranging up to 400 m in thickness away from the domes. The lithology of clasts (typically 1 cm to 1.5 m in size) provides strong evidence that the flanking fragmental unit was derived by explosive eruptions associated with the rhyolite domes. An approximately 15 m thick shale horizon, bleached and silicified at its base, overlies both the rhyolite domes and the frag- mental unit. A south-dipping chloritic pipe-like body, with near-surface dimensions of 1,000 by 250 m and narrowing at depth to produce a cone-shaped cross section, lies within the rhyolitic frag- mental rocks about 250 m north of the largest rhyolite'dome in the Mons Cupri vicinity. Its east west elongation parallels that of the rhyolite dome. Ghost fragments indicate that the material in this fissure is a severely chloritized derivative of the rhyolitic frag- mental unit. The chloritic pipe is overlain

Jan 1, 1973

In spite of the efforts done in the past to implement in Codelco best practice guidelines and standards on several important sampling, assaying and variability issues, many people, particularly top managers and operators, are still not aware of the relevance of the use of the principles and practice of geostatistics, sampling theory, analytical chemistry and the understanding of processes variability from rock to cathodes. As a result, an important challenge for the sampling community is to find out the causes of this lack of awareness and to develop communication skills to influence the organisation, particularly the top management level. This situation is not affecting only Codelco; it is a common characteristic of the copper mining industry. The main cause is cultural. Judeo-Christian and occidental sciences are deterministic. This implies a disregard of process variation and the assumption that homogeneity is omnipresent. Another important aspect of the cultural challenge is education. Education is the most efficient way to transfer a system of ideas, traditions and practices. To implement proper courses of sampling theory and geostatistics and support to multidisciplinary education at universities, mining companies will improve teamwork between geologists, mining engineers, metallurgists and chemists. The improvements will imply a more sustainable and efficient mining business.

Mar 1, 2010

By D Beck, E Jones

The measurement and management of deformation in underground excavations is a key responsibility of geotechnical and mining engineers. A critical aspect of these roles is to ensure there is sufficient ground support capacity for the expected demand.Current methodologies for monitoring deformation and ground support serviceability-limits require measuring displacement at distinct points, or using visual observations. These current methods limit the assessment to a qualitative interpretation of deformation across the entire excavation.Recent advancements of Light Detection and Ranging (LiDar) technology permit a new method for monitoring deformation that allow a full 3D image of extended sections of an excavation to be precisely scanned. The results from the comparison with subsequent scans provide valuable information on the magnitude, direction and extent of regions exceeding the ground support serviceability-limits. This new method now provides a quantitative assessment across the entire excavation being monitored.The implementation of regular scanning has been demonstrated to be highly advantageous not only at mines with swelling or squeezing ground, but also at mines with rapid seismic induced deformation. The use of LiDar technology as a routine deformation measurement tool for geotechnical and mining engineers (and further applications) are discussed in more detail in this paper.CITATION:Jones, E and Beck, D, 2017. The use of 3D laser scanning for deformation monitoring in underground mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By A J. Minns

This paper addresses the question: how can the minerals industry remain viable; viable in the sense that we are able to access land for exploration and discovery, we are able to develop and operate mines (and processing plants) safely and profitably and we are able to close operations in a responsible manner, so that modified landscapes are restored to acceptable community standards?Many of the answers to this question can be addressed through the theme of this conference û that of eco-efficiency. The eco-efficiency concept is very useful, since it does help to translate principles of sustainability into business value at the operational level. To provide some context to how this can be achieved, the paper discusses what is happening at the international level, outlines some key industry initiatives within Australia and then discusses what work is being done within companies.

Jan 1, 2004

The Research Centres Program initiated by the Federal Government and supported by the mining industry has had a major impact on geoscience research and education during the past five years. Eight major university based-Geoscience Research Centres are currently supported by the Government, including four Key Centres of Teaching and Research and a further four Cooperative Research Centres (CRCs). The Research Centres Program has led to a concentration of high quality research and teaching in areas of demand and strategic importance creating strong university - industry linkages and a source of well trained and motivated graduates. Over the last decade Australia's reputation as a leader in mineral exploration and ore deposit research has grown substantially, in part because of the development of the Research Centres Program, and to increased collaboration and interaction between research groups and exploration geoscientists across the industry. During a period when ore deposit research activity has been decreasing in other countries (eg USA, Canada, Japan and most European countries), equivalent research activities in Australia have been increasing, within a well co-ordinated national framework. The future challenge for universities and the mining industry will be to maintain the momentum of the successful research centres in order for the centres to become self-funding over a six- to nine-year period.

Jan 1, 1996

With the next mining boom looming, the industry will once again struggle to meet skills needed as the current generation boomers are set to retire. In order to meet these needs it is going to need to focus on what underutilised human resources - in particular women - want!   Women comprise around 14 per cent of the mining workforce, compared with a 45 per cent participation rate in the work force overall. Within the industry, women still make up only one per cent of trades people, eight per cent of operators/production employees, 12 per cent of engineers and 11 per cent of executive management.   It may be worth pointing out that mining has an age profile skewed towards the older end of the spectrum. When it comes to employee retention, what women want may be a good starting point to examine, more broadly, what all employees might want (but are too afraid to ask!).   Women in mining want the following: To be scrutinised for their work and performance, not their personal lives, appearance or relationships. True pay equity. This is addressed at lower levels between companies but at professional levels the salary differentials begin to appear and little is done to identify why this continues to be the case. Recognition and acceptance that women can have different work-styles, and that diversity of work-styles is an asset to be nurtured not a threat to be neutralised! Recognition that a more diverse workforce demographic that better reflects society at large will assist the company in its dealings with many diverse stakeholders from society at large. For employers to recognise that a career break to accommodate caring responsibilities does not mean that an employee's commitment to progressing their career is any less than that of someone who has not taken a career break. Similarly, for employers to recognise that working part-time for to accommodate caring responsibilities does not mean that an employee's commitment to progressing their career is any less than someone who works a more traditional roster. Access to affordable and quality child care compatible with mining rosters in mining towns. Zero tolerance for bullying and harassment, and workplace cultures that promote respect and safety. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

Energy is central to respond to critical stakes on human and industrial development requirements as well as on climate change. The increase of the share of carbon-free energy sources in the global supply mix will help to reduce significantly greenhouse gas emissions (GHG) as power generation accounts currently for 41 per cent of these emissions from the energy sector. In this energetic mix, nuclear and renewable energies are complementary, the first more focused in the baseload power generation whilst the second is well suited for decentralised power generation. In this context, AREVA's goal is to enable everyone to have access to a cleaner, safer and more economical energy. Regarding nuclear energy, AREVA's strategy is to capitalise on its integrated operation model, which groups together fuel cycle and nuclear power plant construction, aiming at building one third of the new nuclear capacities and securing the fuel cycle supply chain for its existing and future customers. Therefore, the front end of the uranium fuel cycle, from mining to the fabrication of fuel assemblies, has a key role in the sustainability of the nuclear industry. The replacement of the current capacity and the entrance of new countries on the nuclear power generation might lead to a significant rise of uranium demand by 2020. In order to be prepared in time, AREVA defined an ambitious industrial program to expand mineral reserves, increase the production of uranium concentrates, replace the conversion capacity, build two new uranium enrichment plants, one in France and one in the United States and upgrade its fuel manufacturing plants. To support the front-end industrial activities in the short and long term, AREVA invests on a portfolio of R&D projects to find out solutions to meet customers' needs, to improve its competitiveness and to develop new concepts and solutions to anticipate future market evolutions. In particular, some important technological challenges in mining must be surmounted to develop cost-effective methods to explore and exploit low grade deposits while creating sustainable solutions for reducing reagent, water and energy consumptions. In this lecture, an overview of the industrial investments of AREVA in the front end of the uranium fuel cycle and some highlights on its R&D major axis will be presented. This is an abstract only. No full paper was prepared for this abstract.  

Sep 13, 2010

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

Results are presented of the investigation of gas dynamics of the blast furnace process obtained on laboratory models and operating furnaces. Gas residence times were measured using a helium tracer technique developed for the purpose. Residence times were determined in furnaces of 1007 m3 and 1719 m3 and results used in the calculation of the burden parameters and to estimate the distribution of the gas flow along the furnace radius. The effect of tuyere injection of coal dust on gas distribution was also investigated and the advantage of continuous injection compared with intermittent injection is noted. The unevenness of gas distribution across the furnace area is found to correlate well with differences in the size analysis of the iron-bearing component of the burden. The mixing of the gas streams between the neighbouring raceways was studied. It is shown that in the central region of the furnace gases from every tuyere are mixed together, whilst in the peripheral regions mixing is more localised and includes only the sections consisting of five adjacent tuyeres. A solution is proposed to the problem of a theoretical evaluation of the critical gas velocity. A simple relationship between the Reynolds and the Archimedes numbers was obtained from which, after substitution of the burden size data and the gas parameters, it is -possible to evaluate the critical gas velocity. Conclusions include information relating to the optimisation of the gas distribution and views on reducing gas injection at elevated furnace levels.

Jan 1, 1975

By J H. Kyle

Cyanide is a significant cost in gold processing, as well as an environmentally sensitive issue. It has been suggested that precipitation of cyanide from leach liquors as copper-iron-cyanide compounds such as Cu2Fe(CN)6 may account for part of the total cyanide consumption. This may be especially true for ores that are rich in both copper and iron minerals. Ammonia addition has been shown to decrease the cyanide consumption by copper. Cu2Fe(CN)6.xNH3 precipitates have also been postulated to form during conventional cyanide detoxification processes, using oxidants such as SO2/air, with ammonia arising as a breakdown product from the oxidation of free cyanide. The present work has examined the conditions under which such precipitates may form, particularly in gold plant process and detoxification liquors. Ammonia and pH were found to have a large effect on the extent of precipitation. The compounds that were formed were found to comprise mainly Cu2Fe(CN)6.7H2O, as well as a range of NH3-bearing variants. The stabilities of the various precipitates are important from an environmental perspective. The long-term stability of copper ferrocyanide precipitates in tailings dams may be a problem under alkaline conditions and when some free cyanide is present, elevating the measured total cyanide in solution significantly. Case studies including data from actual plants are also considered, and the importance of these effects is reaffirmed from these results.

Jan 1, 2000

In 1955 the annual production of steel at Australian Iron and Steel Pty. Ltd., Port Kembla was 1.2 million tonne and over the following two decades this had progressively increased to the present capacity of 5.4 million tonne per annum. This increase in productivity has also been accompanied by important developments in steelmaking technology and these are explained in the chronological order in which they have taken place. Reference is made to the use of oxygen in open hearth furnaces, the B.O.S. process, the Argon-Oxygen decarburisation process for stainless steel, vacuum degassing and continuous casting. When the vacuum degassing and continuous casting units are commissioned, the Port Kembla Works will have achieved a standard of steelmaking technology equal to any in the world.

Jan 1, 1976

By May J. R

Exploration, including research, has fuelled the enormous expansion of the Australian mineral industry in the last three decades. Analysis of success and failure in exploration and research has therefore potentially powerful lessons and messages which may be used to influence the future shape and direction of the mineral industry. Research has been an integral part of organised corporate mineral exploration since its beginnings in Australia in the 1930s. In corporations, the activity generally called project generation or new project development is the main expression of exploration research but mostly it goes unidentified and poorly documented except perhaps when a successful discovery is made and reported on. The competitive nature of exploration means that extended and detailed analysis of corporate exploration research across the industry is impossible to achieve.

Jan 1, 1992

By R McConnochie, J V. Rowland, J L. Mauk

The Sovereign prospect in the lower Waitekauri Valley of the southern Hauraki Goldfield occurs in daciterhyolite flows and volcanic breccias of the Waipupu Formation. The lower Waitekauri Valley contains a series of NE to NNE-trending normal faults, and the Sovereign prospect lies in a NW-striking graben. The structure of the Sovereign prospect is complex. NE to NNE-trending veins and normal faults dominate the area, however WWNW and N to S-trending structures occur locally. Kinematic analysis of these structures indicates predominantly dip-slip movement, with a local strike-slip component. At least two sets of veins occur in the area: 1.        steeply dipping veins; and 2.       low angle veins, which cross-cut and locally offset the steeper dipping        vein set. Mineralization appears to have formed during normal faulting in an extensional regime.

Jan 1, 2007

BHP Steel International's Newcastle blast. furnaces have operated since their caimissioning on cake based on local low rank coals. In the early 1960's Newcastle coke was believed to be the weakest in the world. Newcastle coke now supports a blast furnace operation with a productivity of 2.1 t/d.rn IV, a fuel rate of 490 kg/t and a coke rate of 415 kg/t. This coke is nuudv from blonds of lcxni and southern Sydney basin coals with blend Ro nex in the range 0.94 - 1.01. Blast furnace performance in periods of differing coal blends is conjured. The relationship between coal aril coke quality indices and blast. fin-mice perforrnarcc.e is discussed as well as the relevance of conventional coke tests. New BHP coke tests are referred to.

Jan 1, 1987

By S Kodate, Ö Aydan, Y Suda, J Tomiyama

Fracture zones are commonly found in the Earth’s crust. These zones may cause very severe engineering problems. Therefore, the formation and the assessment of the mechanical characteristics of these zones is of great concern for rock engineers. A new double shearing jig was used to study the formation of shear zones in rock under static and impact loading conditions using the device developed by the authors. A series of experiments were undertaken to investigate formation on the formation and characteristics of fracture zones in laboratory. Although actual fracture zones are more complicated, various tests give some insight view of the formation of fracture zones as well as some information on their mechanical behaviour under both dynamic conditions and static conditions. The authors report the outcomes of these experiments and discuss their implications in practice.

Nov 29, 2022