Search Documents

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By Young D. R, Webb I. D

The hydro-chlorination of Fe2O3 and Fe304 has been investigated in the range 850-950¦C in order to elucidate the role of iron in the segregation process for nickeliferous laterites. The kinetics of Fe203 chlorination using 20% HC1 - 80% N2 gas mixtures is consistent with a single-stage structure control model, whereas Fe3O 4 exhibits a two-stage reaction mechanism. Oxygen potential measurements using a CSZ probe located above the bed and X-ray powder diffraction results confirm the proposed reaction scheme. When a serpentine nickeliferous laterite (1.03% Ni - 11.7% Fe) was chlorinated at 900¦C with a 20% HCl - 80% N2 gas mixture it was found that the iron oxide in the ore was extracted in a similar manner to the synthetic iron oxides. Also, it was found that the nickel extraction from the ore paralleled that of the iron and the tests indicated that for the major part of the extraction, the solid nickel species were in equilibrium with the gas phase. The recovery of nickel from laterite ores by the segregation process has been investigated by a number of workers and several extensive reviews of the literature associated with this field have been published (Iwasaki, 1972; Canterford, 1975; Wright, 1973).

Jan 1, 1987

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By Bin H

East Guangdong tin province overlaps the southmost part of the mesozoic magmatic arcof continental margin type in Southeast China and is dominated by mesozoic syntectic magmatism,which associated to tin mineralization. It is distinguished from Nanling tin province but quite close to NW Bolivian tin province in both tectonic and magmatic relations.Tin deposit's mostly of cassiterite-sulfide, cassiterite-silicate formations are localized along exsocontact zone of granitoid batholith or stock, boundary area of volcanic depression, or, within volcanic edifice. Petrochemistry studies show tin was concentrated as intermediate-acidic magma evolved by fractional crystallization. Xiling tin deposit of vein type related to extrusive... the lava dome was formed at T C 221-301 and at very shellow depth,seems to correspond to type A in classification for Bolivia tin deposits by J.N.Grant. Tashan tin deposit of dissemination type related to hypergene intrusive facies,with mineralization occured in endocontact zone of granite porphyry dykes is considered as porphyry type,which spported by H-0 isotope and gas-liquid inclusion evidences. It formed at T C 250-430, comparable to Bolivia porphyry tin deposits,but at a greater depth 1.3 3.0km.A model for known tin deposits in East Guangdong was worked out. A good prospecting perspective was revealed for the potential type of tin deposit in East Guangdong--subvolcanic porphyry tin deposit.

Jan 1, 1990

IN the ordinary course of treatment of pyritic ores or concentrates, whether for the recovery of copper, tin, gold, or any other contents, the removal of some or all of the sulphur contents is almost invariably the first step. The practice is to roast the ore in a current of air so that the sulphur is oxidized to sulphur dioxide and the metal constituents are changed from sulphides to oxides. If it is feasible to produce sulphuric acid in conjunction with the treatment process, the sulphur can be usefully employed; but if this is not possible, then the sulphur contents not only become a dead loss, but tend to be a nuisance as well in the surrounding neighbourhood.The problem of avoiding this disadvantage and making economic use of the sulphur has had attention from the early days of scientific metallurgy, and in the past few years very special efforts have been made both to drive part of the sulphur as such from pyrites and recover it, and to replace the sulphur in the S02 by carbon, with the production of carbon dioxide and precipitation of the sulphur. So far economic success does not appear to have crowned these efforts. In the case of pyrites, of the two atoms of sulphur which go to make the FeS2, the first is very lightly held. Dissociation is effected by heat alone at a temperature which is given by Peters as 5160 C.Now, sulphur and hydrogen will unite or burn together, with the production of sulphuretted hydrogen. It occurred to the writer that, if hydrogen was passed over pyrites heated to the above temperature, this first atom would be snatched away by the hydrogen, and could possibly be economically recovered.The first step consisted of some simple laboratory experiments. From these it was found that this first atom was readily removed, and that the extraction was practically complete. Further, the reaction took place at a low temperature, a dull red heat being sufficient.

Jan 1, 1923

By M J. Pascoe

The performance of 460 stope surfaces at WMC ResourcesÆ Olympic Dam Operation (ODO) has been used to investigate the confidence that can be placed in the Stability Graph Method for design of stope dimensions. A detailed database of stope performance and ground condition information was established for each stope. The database contains all the required stability graph information as well as other factors thought to influence stability, such as discrete major structures, poor shape and exposure time. The performance of each stope surface was quantified by calculating Equivalent Linear Overbreak/Slough (ELOS). The performance of stope walls and crowns was plotted on the supported and unsupported case history stability graphs. Based on this information an ODO design limit of HR = 3.3 x NÆ0.33 has been suggested for stope walls. Walls that plotted above this line were 80 per cent stable, 20 per cent unstable and zero per cent failed. Below the line 60 per cent were stable, 30 per cent unstable and ten per cent failed. Supported crowns that are flat or arched in shape and are not within the influence of major structures can be designed in the stability graphÆs æstable zoneÆ with a strong likelihood of stability. The Stability Graph Method did not reliably predict the performance of unsupported crowns at ODO.

Jan 1, 2005

By D Mather

The Resources Boom of the 1960s in Australia provided a strong foundation for AustraliaÆs economic prosperity for the remainder of the twentieth century. In combination with sound economic management, our world-class minerals and energy sector has played a key role in the nationÆs competitiveness, and it has been the major source of our exports since the early 1970s. Even with the emergence since 1990 of major mineral provinces in Latin America and elsewhere, Australia has increased its percentage of world production of several minerals. Between 1990 and 2002, our share of iron ore production rose from 13 per cent to 20 per cent, nickel mine production from eight per cent to 17 per cent, copper mine production from four per cent to seven per cent and zinc mine production from 13 per cent to 17 per cent. Whether this situation will continue during the coming decades motivates the discussion of this reflective paper. The approach is to consider fundamental supply-side and demand-side issues in arriving at a view about the state of the world, the world minerals sector and the Australian resources sector in the coming decades. The argument draws from the experiences of other mature mineral producing countries such as Canada and the United States. In such nations, efficient producers have often sustained competitiveness for extended periods, despite falling grades and other challenging operating conditions. Yet several forces are changing the economic geography of the minerals industry in significant ways. These include the re-emergence of major global mining corporations, the revision of mineral policy in over 100 nations since 1985, the mobility of technology and more efficient transport both for mineral productions and mining professionals. Given these trends the paper argues that the Australian mining industry must continue to change and evolve significantly in the foreseeable future. Its leaders will need to be even more internationally focused if it is to maintain its strong competitive position.

Jan 1, 2006

By R J. Cuttler

In January 1998 Sydney Water Corporation formed an Alliance with construction contractor Transfield, and engineering consultants Connell Wagner and Montgomery Watson, to design and construct the Northside Storage Tunnel. The project is part of WaterPlan 21, Sydney WaterÆs strategy for cleaning up the harbours, bays, rivers and beaches within its business area. WaterPlan 21 is an integral part of the NSW GovernmentÆs $3.1 billion Waterways Package which establishes targets and initiatives for sustainable wastewater management within NSW. The project is being delivered under an Alliance Agreement, which has a number of non-traditional features in terms of partnering, management principles and design and construct. Construction began in mid-1998 and is on target to meet the completion deadline for the Sydney 2000 Olympics.

Jan 1, 1999

By G D. Price

The Golden Blocks Goldfield is located in the Slaty Creek area,North West Nelson, about 20 km west of Collingwood. Alluvial gold was discovered in Slaty Creek in 1861. Gold was mined from quartz veins up to 1.5 m thick at nine mines from the 1890s until the closure of the Aorangi Mine in 1911. Total production from the Golden Blocks Goldfield is estimated at 46 000 ounces of gold. The Aorangi Mine was the largest mine, with a recorded production of 27 978 ounces of gold at an average grade of 36 g/t. Quartz veins containing gold and sparse sulphide mineralisation occur in a slightly metamorphosed, complexly deformed over-turned sequence of Lower Ordovician sandstones and shales. Primary gold mineralisation is associated with intensely deformed zones that occur near or at carbonaceous shale and sandstone contacts. Some eighty-five percent of all gold production (39 000 ounces) came from four mines confined to the stratigraphically lowest, most widespread shale unit. The quartz veins exhibit textures consistent with a hydraulic fracturing mode of vein formation with fissure infill vein types predominating over replacement textures. Stylolites of carbonaceous material and recrystallization features within the veins suggest multiple phases of deformation. The lack of wall rock alteration, and low primary fluid inclusion temperatures of 200¦ - 265¦ indicate that the ore fluids were associated with a low temperature epithermal system. A model consistent with similar mineralisation styles observed in Ordovician sediments from Pacific Rim occurrences is presented. The high grades (up to 100 g/t) mined from the upper levels of several mines suggests supergene enrichment processes associated with the Upper Cretaceous weathering surface. The Golden Blocks Goldfield has had no modern exploration. The most recent exploration was undertaken in the early 1980s. There are known acid intrusives in the area, with potential for the application of new models of intrusive-related gold mineralisation.

Jan 1, 2004

By I Canbulat, G Si, Y Duan, X Luo

The presence of unfavourable geological structures such as faults and dykes often can contribute to coal burst risk. Seismic events associated with rock fractures tend to cluster around these structures and it is important to understand the characteristics of seismicity for coal burst risk management. In an Australian underground longwall coalmine, two clusters of seismic activities close to the longwall face and within a section of the maingate roadway which was intersected by a major dyke were respectively identified. The induced seismicity in the dyke-roadway area was closely related to the longwall mining. These seismic events were located and the distribution of seismic events shows that more fractures were distributed on the inbye side of the dyke. The spatial-temporal changes of the seismic event locations delineate the fracture propagation as the longwall mined through the dyke. The frequency-magnitude relationship of seismicity was analysed and it was found that it changed significantly when the longwall was mining towards, through and past the dyke. The monitoring results demonstrate that because of the stiff dyke, the seismicity was intensified in the roadway section. It proves that the dyke promoted stress re-distribution and seismicity in its vicinity. More fractures were induced in the hanging wall of the dyke, whereas less strain energy was accumulated and released in the footwall of the dyke.

Nov 29, 2022

Quantitative probabilistic ecological risk assessment has been used to evaluate the likely effect on fish diversity and abundance of filtered and bioavailable metals in streamwater affected by acid drainage from the abandoned and remediated Rum Jungle U/Cu mine in the Northern Territory of Australia. The water quality was determined using monitoring data from a gauging station on the East Branch of the Finniss River, downstream of the mine site, and modelled assuming a number of potential water quality management options. The management options ranged from no action, through some flushing options to full catch and treatment of contaminated seepage from the waste rock heaps. The computer code AQUARISK was used to undertake the analyses. Critical criteria for contaminant water concentrations at the site, derived from probability density functions of available fish ecotoxicology data, were found to closely approximate the regulatory trigger values for the contaminants of concern. Modelled predictions of reduced diversity and abundance were also in good agreement with in situ biodiversity measures. Based on a reasonable target of 67 per cent species tolerance for this heavy impacted site, it was found that none of the low cost options for wastewater management was acceptable. Combinations of two of the options approached acceptability. Both of the catch and treat options exceeded the arbitrary acceptability target well. This implied that the more expensive option of liming to pH 10 might be unnecessary at this site. Thus, the use of ecological risk assessment modelling has proven useful in undertaking cost-benefit analyses for this site. The approach provides a management decision-making tool that can be economically used to link expensive on-site environmental engineering options with site-specific ecological goals rather than the previous nebulous aims of æreduced contaminant loadÆ or æimproved biodiversityÆ that often resulted in excessive expenditure without achieving successful environmental benefit.

Jan 1, 2003

In late 1984, Council of the Australasian Institute of Mining and Metallurgy accepted a proposal to establish a Mineral Heritage Committee. This was to be involved in matters relating to mineral heritage-its recording, its preservation, and the acknowledgement that it can be of use to the mineral industry in the future. The Committee was established to ensure that all of the disciplines of our profession were included and that, so far as possible, all of our country as well as those countries of the Southwest Pacific Basin were represented. Some work has been commenced to bring real- isation of the importance of the heritage of our mineral industry to the forefront of the commu- nity's interest. There is not a state in this country and the Southwest Pacific where the mineral industry has not at various times proved to be the basis of community development.

Jan 1, 1987

By Morris A. E

The thermodynamically-based pyrometallurgical simulation software STEPSOL (Version 3.0) provides for the modelling of activities using the Interaction Parameter Model, the Regular Solution Model, the Sub-Regular Three Suffix Margules Model, the Sub-Regular Four Suffix Margules Model and various simpler polynomial models. These are briefly reviewed, along with the major sources of data available in the literature, and the implementation of the models in the program.

Jan 1, 1991

By M J. Saynor, J B. C Lowry

The Ranger Uranium Mine is located in the wet-dry monsoonal tropics approximately 250 km east of Darwin in the Northern Territory of Australia (Figure 1). Mining of open-cut ore bodies commenced in 1980 (Pit 1) and ceased in 2012 (Pit 3) and milling and production are scheduled to cease by 2021. At the conclusion of mining and milling operations, mine tailings will be returned to the mined out pits 1 and 3, which must then be physically isolated from the environment for at least 10,000 years (Australian Government 1999). The final landform also needs to have sufficient mitigation measures in place to ensure that areas downstream are not impacted by erosion products from the mine site. The proposed post-mining rehabilitated landform will cover approximately 847 hectares (8.5 km2) which represents an area that has the potential to supply sediment to catchments and streams downstream. One method of reducing runoff and associated sediment is the construction of rip lines along the contour to slow down the runoff velocity and to also trap fine sediment and nutrients in the depressions to assist vegetation growth.CITATION:Saynor, M J and Lowry, J B C, 2018. The impact of rip lines on erosion at the Ranger Mine Site, in Proceedings Life-of-Mine 2018, pp 150–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By G Chitombo

Mass mining methods have become the mining industry’s preferred way of extracting most of the world’s most important metal and mineral commodities. Given the rapidly increasing global demand for commodities, the requirement to increase the contribution of some of these (eg copper and gold) from underground sources also continues to grow. In the case of copper this contribution is needed by a number of major producers to supplement production from their ageing deep open pits. Satisfying this increased demand will require the design, construction and operation of more effective, higher capacity and larger scale mines which, in turn, will require enhanced mass underground mining techniques such as block caving (BC), panel caving (PC) and sublevel caving (SLC).It is now widely accepted that future discoveries of orebodies, which will be developed using these methods, are almost certainly to be much deeper than the deposits presently being mined in this way and made more challenging because of the likelihood that the associated grades may be much lower than currently mined. The design and mining of future large-scale cave mines (supercaves) will become crucial in order to extract full value from such deposits. An essential prerequisite of this will be a much improved knowledge of the deposit, ie Total Deposit Knowledge. In this context, Total Deposit Knowledge is the characterisation of the ore deposit and its surrounds at all scales and includes; rock type (lithology), the spatial orientation of a range of geological features or discontinuities, rock mass fabric knowledge, metal grade and distribution data, geometallurgical data (including alteration), geo-hydrology, permeability and porosity. This is the information that will be used, as now, to delineate geological and geotechnical domains and construct models, but with outcomes superior to those presently available. From this information better-informed feasibility study design decisions and performance predictions must be made. In summary more geological information and analysis is required and this needs to be aligned to potential mining and processing requirements much earlier in the project than commonly occurs.

Aug 22, 2011

By Toussaint LF

A brief history of the mineral sands industry is given from a radiation protection standpoint, with gamma radiation and inhalation of radioactive dust being identified as the main sources of radiation exposure of persons working in the plants. The principal sources of gamma radiation exposure are identified and the history of early bagging methods is discussed. The concept of ALARA is introduced and the impact of the "bulka bags" (and more effective monazite storage facilities) are detailed as illustrative examples of dose minimization, together with the requirements for the transport of monazite. The dose from radiation received from inhaled dust is dependent on a number of parameters of the dust, some of which are not well known. ICRP 30 (1978) makes recommendations relating to the intake of radionuclides by workers. These recommendations are discussed with respect to the inhalation of dust containing thorium. The possible pathways of radioactive material throughout the body are also described. The effect of having parameters that differ from ICRP 30 is discussed and suggestions are made relating to measurements that can be carried out to more accurately determine these parameters. Since in some instances the exposures to dust yield personal doses which may exceed the annual ICRP 30 based limits, it is necessary to define more accurately parameters of the dust so as to determine more accurately personal Doses.

Jan 1, 1986

By Bucknell WR, Clarke DE

The paper provides a company's view of the relative merits of various valuation methods and outlines the basic approach it takes to the valuation of an exploration property. The negotiating process and methods of acquiring an interest in an exploration property is discussed The valuation methods discussed are: 1. Exploration Expenditure. 2. Real Estate. 3. Joint Venture Terms. 4. Rule of Thumb. 5. Net Present Value - Discounted Cash Flow. 6. Geoengineering.

Jan 1, 1994

By W A. van der Westhuizen

Selective mining played a major role in saving a mine and a communityÆs existence as well as creating a working culture that is the model for all KumbaÆs mines. The successes that resulted from selective mining led to receiving KumbaÆs highest award (it was the Gold Medal Breakthrough project of 2003) as well as the productivity award at the National Productivity Institute award ceremony in 2004. Kumba was established in November 2001 (previously Iscor Mining). The new company identified Mineral Resource Management (MRM) as one of its key drivers and an initiative was launched to define MRM in the Kumba way. Best MRM practices at the Kumba mines were included in the definition. Selective mining was born out of this initiative. One of the key principles of good MRM practice was identified as: æThere must be a balance in the operational processÆ. This principle was applied with great success at Thabazimbi Iron Ore mine in the Limpopo province, South Africa. The emphasis of this paper will be to show how value can be unlocked throughout the whole mining value chain. In the past (up to 2001) the mine went through a number of crisis situations: planned production performances were not reached, the stripping ratio was extremely high with two new pits, the product beds were not of constant quality, slope failures were big risks, flooding could and did cut off half of the ore supply, and restructuring demoralised staff.This paper focuses on: selective mining throughput drivers, and selective mining and its role in achieving this balance.The results were dramatic, with huge improvements in production results, stockpiles, plant yields and product bed specifications. The mine was brought into balance and a self feeding loop was created with positive spin-offs up to this day.

Jan 1, 2005

At the outset I want to thank you for inviting a representative of the Chamber of Mines of South Africa to address you on the subject of mining and its future at this, the 13th Congress of the Council of Mining and Metallurgical Institutions. It is indeed a pleasure and an honour to be here. As many of you will recall, four years ago I, as the then President of the South African Institute of Mining and Metallurgy, had the privilege of hosting and welcoming you to the 12th Congress, the third such congress hosted by South Africa. The late Sir Ernest Oppenheimer, President of the 1930 Congress - the first to be held in South Africa - in his opening address foresaw the mining industry as "the most potent factor in spreading the benefits of civilisation over the sub-continent." We have come a long way since those halcyon days but, as I noted four years ago, it still remains true that mines have been, and will continue to be, the missionaries of development in many, if not most, of the Third World countries. I have been asked to address you on the subject of "mining" and to let my imagination roam widely so that delegates can leave the congress with a broader vision than they brought on arrival. It is a tall order and in my attempt to fulfil it I ask you to cast your minds back 120 years to a sultry, rustic day when the first diamond was discovered in South Africa at the now famous town of Kimberley. At that time the South African economy, predominantly pastoral, was still at subsistence level. Almost overnight the ensuing diamond rush turned the then British- owned northern Cape Colony's semi-desert scene into a hive of mining activity, every prospector bent on making his instant fortune. It was very little different, I am sure, to the gold rushes that hit California in 18+8, Australia in 1851, New Zealand in the 1860s. and the Yukon in the 1890s.

Jan 1, 1986

MANPOWER RESOURCES The optimisation of human effort has been an ongoing and significant process in the coal industry since industrialisation as we know it began. The extent to which the changes sought have been achieved has, over the years, been in the main determined by the economic and political forces existing at that time and the determination and character of the individuals involved. The question of optimisation is therefore not new in our industry. Hopefully this presentation will demonstrate to the reader the effect of previous measures adopted by industry to optimise all facets of its operation and in particular that of the human Resource.

Jan 1, 1991