Search Documents

By Otuonye F

An outburst is the spontaneous ejection of pulverized coal and gas from the working face in an underground mine. It is caused by overstressing the rock, due predominantly to the influence of geological structures on in situ stresses, stress concentration from the excavation and overburden load on mine openings, and large volumes of gas sorbed in the rock. The spontaneous release of high pressure gas creates intense shock waves which may cause damage to the mine ven- tilation system and the pulverized rock/coal ejected may cause injury or death to miners. The gases emitted pollute the mine air and may also result in death to miners.

Jan 1, 1988

By D Reid

Run-out analyses of tailings storage facilities are typically undertaken using methods based on rheological theory. These are reasonable techniques to model the behaviour of tailings that, through significant run-out and possibly mixing with supernatant water, are generally acting in a fluidised manner. Such modelling often follows on from two-dimensional continuum analysis models where, if failure is predicted, grid failure often occurs when deformations begin to increase. This results in a disconnect between the prediction of failure and the modelling of the potential extent of the failure.Recently, rezoning methods have been incorporated into commercially available two-dimensional soil mechanics deformation codes. Rezoning techniques enable large deformations to be modelled within a two-dimensional continuum analysis framework; however, while promising, the use of such tools is not yet widespread, and a consensus is yet to develop on how they should be applied to tailings dam run-out modelling.This paper uses FLAC rezoning techniques to model the flow behaviour of two historic tailings dam failures. The purpose of these analyses is to critically assess the performance of rezoning against some available historic failures. The required data to undertake such an analysis is outlined, along with the inherent limitations and assumptions required. Parametric analyses are outlined to address some of these issues. In general, the analyses undertaken underestimated the flow distance observed in the historic failures by varying degrees; however, in some instances, the analysis reasonably reproduced the qualitative shape of the initial failure zone. A variety of potential reasons for the discrepancy between historical observations and the models undertaken are provided.CITATION:Reid, D, 2015. The use of rezoning techniques to model historic tailings failures, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By P Craig, M Holden, C Zhang, D Foster, J Oh, S Saydam, J Liu, H L. Ramandi, S Akdag

High stress in rock masses can cause significant instability problems such as squeezing deformation in soft rock and rock bursts in hard rock. The support system applied in burst-prone areas in high-stress conditions is required to be able to carry high load and accommodate large deformation of the rock mass without experiencing any serious damage. Yielding support systems are promising to provide support for both squeezing and burst-prone rock mass encountered in mining or tunnelling at depth. They are ideally strong and stiff initially and then ductile after yielding (Potvin and Hadjigeorgiou, 2020). With respect to support design, a ground support system has to create a safe working environment under both static and dynamic loading conditions by providing the functions of reinforcing, retaining, holding and connecting elements (Cai and Kasier, 2018). Rigid rock bolts and cable bolts perform reinforcing and holding functions of a ground support system. In highly fractured ground or with large excavation spans (eg at roadway intersections or in caverns), unstable ground depth can exceed the length of typical rigid rock bolts (ie greater than ~3.0 m). In such cases, flexible cable bolts are needed to tie the reinforced and retained rock mass back to deeper and more stable rock. The flexibility of cable bolts allows anchor lengths greater than the tunnel opening that would otherwise restrict rigid bolts. Cable bolts also offer higher strength to weight ratio, with tensile strengths 2–3 times that of standard rebar bolts. This high strength comes at the cost of lower strain tolerance, typically around 5–7 per cent at break. Despite the lower strain tolerance, cable bolts are often used as dynamic support in demanding burst-prone ground conditions. The lower strain tolerance is compensated by allowing sufficient free length for stretching or incorporating a yielding device. There are a number of dynamic cable bolts available on the market and a number of testing campaigns have been undertaken to quantify the dynamic performance of these cable bolts. This paper reviews the existing range of dynamic cable bolts and discusses the potential areas for improvement and further research.

Nov 29, 2022

In a high pressure rolls crusher two force components: the pressurising thrust and the rolling force can be measured experimentally. Computer analyses have revealed regular patterns of stress distribution in the confined material between the rollers. Based on the computer analyses and experimental results a one-dimensional comminution model has been developed.

Jan 1, 1995

By Batterham R. J

Some developments in copper, lead and zinc extractive metallurgy which have gone in to production or seem to be close to production scale are described with emphasis on why these innovations have been adopted.Mineral processing operations are now using: automated quantitative mineralogy,high capacity fine crushing equipment, ò fine grinding equipment, andcolumn cell flotation.Extractive metallurgy plants are using:ò bath smelting of concentrate at various scales, and ò flash converting of copper.Hydrometallurgical process developments are slower to make a commercial impact. Concerns about ability to handle impurities in the feed and production of saleable by-products are often major hurdles.An expression for the probability of implementing the first example of a new development is presented.

Jan 1, 1992

By A Rantala, J Timperi and J Kaartinen, T Maksimainen, O Haavisto

"X-ray fluorescence (XRF) is the most common technique used for online slurry assaying in base metal flotation applications. Typically, assays from feed, concentrate and tailings slurries are used to monitor and control the flotation circuit, with possible additional sampling locations in other main slurry flows inside the circuit. The elemental content detection from the XRF spectrum is relatively straightforward as the spectrum contains element-specific peaks whose height corresponds to the element concentration in the sample. However, centralised XRF analysers measure the elemental concentrations line-by-line, which may increase the sampling interval for an individual line and cause unnecessary response delays, especially in large flotation plants. Reflectance spectroscopy is an emerging technique that can be used to obtain more frequent measurements from slurries. The measurement is based on the mineral-specific absorbance of light in the visible and near-infrared (VNIR) wavelength range. Due to this relatively inexpensive and simple measurement system, it is possible to conduct the measurement simultaneously in several slurry lines. However, the information contained in the VNIR spectra is more difficult to interpret as concentrations of all the minerals in the sample contribute to the measured spectrum and changes in solids content, particle size and mineralogy disturb the elemental content estimation. Therefore, frequent calibration of the measurement is required. This study presents the application of combined reflectance spectrum and XRF measurements for rapid online slurry assaying in a copper-nickel flotation plant. The XRF assays are utilised as calibration samples for the reflectance spectrum measurement, keeping the calibration model up-to-date. The rapid reflectance spectrum analysis is then used to provide an almost continuous estimate of the slurry contents, enabling further improved process monitoring and control.Citation:Haavisto, O, Maksimainen, T, Rantala, A, Timperi, J and Kaartinen, J, 2016. Reflectance Spectroscopy with X-ray Fluorescence for Rapid Online Assaying in a Copper-nickel Flotation Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Liu H, Chen S

Natroalunite is one of colouring minerals in kaolin. In this investigation, natroalunite, on which Ca(II) was adsorbed, was flocculated by HPAM and kaolin was depressed in suspension. The adsorption of Ca(II) on the natroalunite surface was studied by zeta-potential measurement and Auger Electron Spectroscopy analysis. Ca(II) was adsorbed more on the natroalunite surface than on the kaolin surface. The mechanism of Ca(II) adsorption was considered to be chemical adsorption on natroalunite and to be physical adsorption on kaolin. It has been found that Na6P6O18 and Na2Si04 can strongly affect Ca(II) adsorption on the surface of kaolin, but weakly on the surface of natroalunite. The effects of degree of hydrolysis and the molecular weight of HPAM, the effect of pH and the effect of Ca(II) have been studied. The kaolin ore, containing SO3 1.05 per cent has been processed with this method. The products only containing S03 0.36 per cent and the weight ratio of concentrate 52.27 per cent were Obtained.

Jan 1, 1993

By Sijing Cai, Chengpu Zhou

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By P Edmondson, S Narendranathan, S Setchell

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste landform. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using a case study developed at a large iron ore open pit mine in the Pilbara region of Western Australia.CITATION:Narendranathan, S, Lee, E C, Setchell, S and Edmondson, P, 2015. Modelling of an integrated waste storage facility, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By C Lower

An unprecedented, quantitative, deposit-scale understanding of major clay mineral distribution throughout the Yeelirrie uranium deposit has been achieved by adapting the existing HyLogger™/HyChips™ analytical technique to measure resource assay pulps. Spectral analysis via HyLogger™ and HyChips™ systems has previously been used as a small-scale geometallurgical research tool, but never before has it been quantitatively applied to an entire resource sample population for the purpose of developing stand alone block models for major clay minerals. Economic uranium mineralisation within the thin but extensive Yeelirrie?palaeochannel?primarily exists within the transition zone between a groundwater-derived calcrete and the underlying clay-quartz regolith. Early geometallurgical investigations identified that certain clay minerals could be deleterious to the efficiency of the uranium recovery process. Accurate calculation of clay mineralogy from resource assays proved too difficult due to chemical similarities between co-existing kaolinite, smectite and magnesium carbonate minerals. A relatively low-cost, efficient and accurate method of quantitative clay mineral analysis was required to measure over 70 000 resource assay pulps. After initial testing and comparison with QXRD, the HyChips™ 3-1 spectral logging system was implemented as a primary method of clay mineral analysis for the Yeelirrie uranium deposit. The resultant spatial data set allowed the interpretation and geostatistical analysis of geometallurgical domains across the deposit. Clay block models were generated and used in geometallurgical resource calculations to benefit the mine planning process.

Sep 5, 2011

By O Aydan, K Sugiura, A Sakamoto

It is well known that some sinkholes or subsidence take place from time to time in the areas where abandoned room and pillar type mines exist. The authors have been involved with the stability of abandoned mines beneath urbanized residential areas in Tokai region and there is a great concern about the stability of these abandoned mines during large earthquakes as well as in long term. The 2003 Miyagi Hokubu and 2011 Great East Japan earthquakes caused great damage to abandoned mines and resulted in many collapses. Particularly the effect of the quality of backfilling of abandoned mine below the urbanized areas is very important under static and dynamic conditions. The authors present the effect of the quality of backfilling on the ground subsidence associated with abandoned lignite mines under static and dynamic conditions and discuss its implications on the urbanized areas above abandoned lignite mines in this study. CITATION:Aydan, O, Sugiura, K and Sakamoto, A, 2018. The quality of backfilling of abandoned lignite mines on ground settlement under static and dynamic conditions, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 134–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Shuen, R Sales, D La Rosa

Semi-autogenous grinding (SAG) mill control is complex and depends on many dynamic process variables. Good control strategies ensure that a mill is operating as close to optimal as possible, resulting in significant economic benefits to an operation. Pueblo Viejo, a gold mine in the Dominican Republic, has been actively improving their control strategies since start-up in 2012, and one of these initiatives was to install an acoustic monitoring system on the SAG mill. The data from the system is used to optimise the mill’s performance by limiting the time the mill is either running too quiet or too loud. The lower limit is an indication that the charge in the mill is too high for efficient breakage or that the mill speed is too low and grinding media are not striking the toe of the charge. Conversely, when the acoustic emissions from the mill are too high, this can indicate that the balls are striking above the toe of the charge, resulting in inefficient grinding and excessive liner and lifter wear. Adjusting mill operating conditions to keep acoustic emissions in the ‘sweet spot’ between these limits results in more efficient grinding.Pueblo Viejo installed a Metso SmartEar™ to monitor the acoustic emissions of their SAG mill in January 2013. This system has been installed on many mills around the world and is specifically designed for optimising SAG mill control. One system output is the impact counter which measures steel-on-steel impacts on the mill shell. The impact counter uses both frequency and time domain analysis to approximate the number of ball impacts per minute. This method of analysis excludes parts of the sound signal not associated with steel-on-steel impacts and gives an accurate measure of this critical control parameter. After the acoustic system was installed, Pueblo Viejo collected data to determine the upper and lower limits for the impact count variable. The live data is available to the mill operators and it is used as one of the key operating variables to control the mill.Through continuous improvement and the use of advanced technologies like SmartEar™, Pueblo Viejo are improving the control and operation of their SAG mill, resulting in reduced liner wear, more efficient mill performance and optimised energy consumption. This paper discusses the installation of the system, and the measureable benefits obtained by using acoustic monitoring to control their SAG mill.CITATION:Shuen, D, Sales, R, Wortley, M and La Rosa, D, 2014. The benefits of using SmartEar™at Pueblo Viejo, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

Historically the insurance industryÆs involvement in any project has been relatively late in the process. Often it was a case of the last item to be ticked off the checklist has been to ensure that the insurance is in place. However, in more recent times insurers have imposed more restrictions on the cover they are prepared to provide, which has in some cases necessitated a change in the contracting structure to accommodate the insurance policy(ies). In addition, changing contractual practices have changed the allocation of risk between the various parties involved. This calls for a more proactive approach to the design and implementation of an insurance program for both the construction and operational phases of any resource project. This paper explores how a risk managed approach to the design and implementation of an insurance program for a resource project can align itself with current management approaches to project development. From the authorsÆ experience, this approach is best adopted early on in the project (often in conjunction with the bankable feasibility study) and follows AZ/NZS4360 to objectively examine and compare a wide range of risk exposures of the project in a time-effective manner across the following areas: personnel; environment; general management; compliance û legislation, systems, protocols; asset management; change management; financial impacts to the organisation; products/services; service delivery; and technology. Having identified and then analysed the risk exposures according to common consequence and likelihood ratings the next step is to develop a risk map of all considered exposures. The true value of this approach lies in the development and implementation of a risk treatment plan for identified exposures where the exposure is unacceptable. The plans will lead to the optimal solution to the appropriate risk prevention, risk mitigation and risk transfer options available. This paper also examines other benefits to the project that may arise from adopting a risk managed approach in addition to the ability to design an insurance program which recognises the exposures and the ability of the organisation (and other project parties) to retain risk.

Jan 1, 2007

The Manto Verde copper mine (Atacama Region, Chile) is due to go into production in 1996. It will produce 40 000 tonne/year of copper cathode by heap leaching/SX-EW. Mineralogical studies were undertaken in conjunction with the metallurgical testwork program to characterise the ore and its response to leaching by dilute sulphuric acid. The leachable copper mineralogy is dominated by the oxide copper minerals: brochantite and malachite with minor chrysocolla and atacamite. The gangue minerals include abundant orthoclase, specularite, quartz and chlorite with minor muscovite and trace smectite clay, calcite and limonite. The study showed that complete or partial decomposition of calcite, chlorite, smectite and wad consumed acid and generated solution impurities (Ca2+, Fe2+, Mg2+, A13+, K+, Si4+ and Mn4+2+ ). Although these were manageable at Manto Verde, their uncontrolled build-up could have affected the operation in several ways: the degradation of heap penneability and fonnation of crud in the SX plant from the precipitation of gypsum, goethite, colloidal silica and jarosite; and the entrainment of contaminated pregnant leach solution in the SX organic resulting in the transfer of impurities to the electrolyte and subsequent effects on cathode quality and electrowinning efficiency. In conclusion, process mineralogy played an important role in understanding and managing potential mineral-related problems in the heap leaching and SX-EW recovery of Manto Verde ore.

Jan 1, 1994

By D J. Williams, G W. Wilson, S, A B. Tran

A comprehensive field program was implemented to evaluate the internal structure and hydrology of two full-scale waste rock piles. The excavation of waste rock dumps for in-pit disposal at the two mine sites provided an opportunity to characterise the in situ properties of the dumps given contrasting geologic and climatic settings. The internal structure and materials within the dumps were observed and sampled as the waste rock piles were being excavated and placed in the open pits for permanent closure. The field program was designed to fully characterise the structure and material properties of the waste rock. The alteration of the material by physical and chemical weathering was also observed. Samples were analysed for paste pH, water content, grain size distribution and geochemistry. In situ density and matric suction were also measured. Soil water characteristic curves and saturated hydraulic conductivity were measured for representative materials. These properties were used to predict seepage pathways through the waste rock and the resulting outflow geochemistry using the finite element model SEEP/W. The materials in the dump at Site 1 were predominantly fine-grained in texture and highly weathered. The presence of dipping beds with alternating coarse and fine materials was evident throughout the profile of the dump. The structure of the waste rock appears to have an impact on the hydrologic pathways within the waste rock pile. The material in the dump at Site 2 was found to be competent and resistant to particle size breakdown. The particles range in size from clay size to large boulders with the median particle size being approximately 125 mm in diameter. The coarse-grained texture of the waste rock resulted in a loosely packed arrangement of coarse particles with little matrix material infilling the pore spaces between the coarse-grained particles. Seepage modelling for Site 1 was completed to predict seepage paths based on observed structure and hydraulic properties measured in the laboratory. The modelling showed that materials with a fine grain size distribution become the dominant pathways for flow through the waste rock pile. The modelling also showed that layers with high silt and sand contents are subject to the highest flow rates. Finer grained clay rich layers have a low hydraulic conductivity and do not convey large volumes of water. Alternately, coarse gravel and cobble materials are unsaturated under values of matric suction that approach the residual water content of the material and do not transmit liquid water. The seepage modelling together with the results of the geochemical analysis show that the dominant particle size that receives the most fluid flow and flushing ranges from fine sand to silt, corresponding to materials with air entry values ranging between 5 kPa to 50 kPa.

Jan 1, 2003

It is no longer adequate in running mines and quarries to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency. This requires efficient production and commercial processes together with systematic involvement of people in continuous improvement of processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. Unfortunately, even though these principles are proven in all industry sectors worldwide, they have not always been used correctly. This paper describes basic methodology for correct use of these principles to successfully improve the productivity of rock breakage production processes.

Jan 1, 1995

By P Holtham, K Duffy, L Pyle, W Valery

The mining industry is becoming increasingly focused on pre-concentration due to its potential economic and environmental benefits, particularly for the more complex, low-grade, high throughput operations now being developed. Advances in technology have seen bulk ore sorting (BOS) trialled at several operations. However, BOS should not be seen as a ‘silver bullet’, it can offer significant benefits, but only under the right conditions. Deposits with interspersed mineralogy or disseminated, fine-grained minerals can be difficult for BOS. Large batches of barren or low-grade material are required for BOS to be effective. Hatch has recently completed several studies for clients who believed that bulk sorting was the most suitable pre-concentration technique for their operation, based only on an assumed sorter recovery or on laboratory trials of the chosen sensor. However, minimal consideration had been given to the heterogeneity of the deposit, the achievable separation batch size or sensor repeatability. Evaluation of BOS needs to consider both heterogeneity and sensor suitability. The valuable or gangue mineral must be present in such a way that it can be separated effectively in the large bulk sorting batch sizes, without competing minerals or changing ore characteristics affecting the metal upgrade or recovery. Also, the sensor chosen must be able to detect either the valuable mineral, a proxy for the valuable mineral, or a gangue mineral for rejection with sufficient accuracy and precision (repeatability). This paper presents three recent case studies, emphasizing markers which indicated that bulk sorting was unsuitable for the project whilst highlighting the pre-concentration technologies which were applicable (including particle sorting, and coarse particle gravity separation). The modelling methodology, equipment sizing and forward work plans developed to verify these alternative solutions are also presented, demonstrating the key factors contributing to a thorough scoping assessment.

Aug 24, 2022

Gold and copper mineralization in the Parkes area is hosted by a meridional sequence of Late Ordovician to Early Silurian igneous and sedimentary rocks on the central northern edge of the exposed Lachlan Fold Belt. The mineralized area straddles two zones separated in part by the Parkes Thrust and exhibiting different styles of deformation and mineralization (Figure 1). The western zone is characterized by gently folded rocks, with shallow dips and weak to non-existent axial plane cleavage. Faulting is restricted to directions oblique to bedding. Numerous occurrences of minor copper mineralization are known, but of recent national importance is the discovery of the Coradgery- Goonumbla porphyry copper-gold deposits by Geopeko Ltd. A resource in excess of 250 million tonnes has been delineated (Jones, 1985), and this represents the first porphyry deposit of sufficient grade and tonnage to be potentially mineable in New South Wales. The eastern zone is much more strongly deformed. Folding is tight with strongly developed axial plane cleavage. Faulting is abundant both parallel and oblique to bedding. Quartz veining is also abundant, and a narrow belt of gold mineralization adjacent to the Parkes Thrust stretches from Forbes in the south, through Parkes and Peak Hill, to Tomingley in the north. Over 31 tonnes of gold have been produced from this gold belt, mostly before 1914, and now three deposits show good potential for redevelopment - Peak Hill, and the London-Victoria and Lachlan lines of lode.

Jan 1, 1987