Search Documents

So many emergencies that crop up in mining necessitate a departure from ordinary methods that the writer has been led to illustrate a few of the examples that have come under his notice during a somewhat lengthy career; and as most of the methods illustrated are certainly outside the ordinary, it may be hoped that while to many they may convey little that is new, to the larger number some acceptable information may be gleaned whenever the occasion calls for it. Experience has shown that there can be no hard and fast rule in mine timbering that will fit the varying- necessities of different localities, and the engineer must divest his mind of all prejudices that his practice of any particular system or systems may have induced, and must direct his attention to the character of the local timber and its fitness or otherwise for the purpose he has in view. Fortunate indeed are the man and mine that can claim an abundance of good and cheap mining timber it simplifies, oftentimes, what would be, under unfavourable timber conditions, a difficult problem. In many parts of the States there is either none or at best a scrub if the latter, he has to either pigstye, balk, or bulkhead, if his ground will permit; if, not, and the necessary timber has to be imported, then some system of recovering his timber and using it over and over again may be possible. As an illustration of this, Fig-s. Nos. I and 2 show a method applied to the copper deposits of the LyellTharsis, Tasmania. The workings were wide; varying from 30 ft. to 50 ft., and the deposit a taIcose schist of fairly good...

Jan 1, 1902

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

The area around Big Bell was actively explored and sporadically mined for gold from 1904 onwards. The lease was named Big Bell in 1913. The property became established as a major mining centre with the development of the Big Bell underground mine in 1936. Mining operations commenced in late 1937 and ceased in January 1955, after milling 5.56 million tonnes of ore and producing nearly 21 tonnes of gold. In 1969 Australian Consolidated Minerals Ltd (A.C.M.) acquired the deposit then explored it alone and in joint venture until the current joint venture agreement with a subsidiary of Placer Pacific Limited (PPL) was negotiated in 1984. Following exploration and evaluation of near surface mineralisation, and a reassessment of the remnant pillars underground, the concept of a large open pit in conjunction with an underground mine evolved. The feasibility study was completed in October 1987, and the decision to go ahead was formally announced on 2nd December 1987. Placer Dome Technical Services Ltd were contracted to be the Project Managers, commencing construction on site early in January 1988 and handing the plant over to the operators 13 months later. The capital cost of the project at handover was estimated to be $133 million. The operating team commenced pre-production stripping of the open pit on 1st May 1988. By 31st January 1989 almost 16.0 million tonnes had been stripped and 350,000 tonnes of ore stockpiled.

Jan 1, 1989

Few, if any, reliable thermodynamic data are available for the activity of tin oxide in slags. In this work, the activity of the oxide in silica saturated iron silicate slags has been measured at 1573 K using the equilibrium Sn (alloy) + Y2O2-SnO (slag).Slag and a Ag-Sn alloy were sealed in a zirconium oxide crucible to prevent the escape of volatile tin oxide, and the oxygen pressure at equilibrium measured in situ using the zirconium oxide as a solid electrolyte. Activity of tin was calculated from known data for the Ag-Sn system and activity of tin oxide calculated from free energy data. The results have been extrapolated to predict the industrially important distribution of tin and iron between Fe-Sn alloy and iron silicate based slags.

Jan 1, 1983

By Tanner A. C, Harraway D. H

Various circuits were tried at Mount Isa Mines during the period 1959 to 19G3 with the objective of improving the differential flotation of galena and sphalerite. Many benefits and disadvantages of the various circuits were revealed. An analysis' of ore characteristics and their effect on flotation was made -and resullted in the design of a proposed circuit which is currently in the process of installation.INTRODUCTIONSince 1936 when lead-zinc sulphide flotation commenced at Mount Isa, at least three types of ore have been encountered.Each ore has presented problems to flotation metallurgists.The three types of ore are,1. partially oxidized upper level sulphide ore,2. Black Star ore from the lower levels with its carbonaceous fraction, and3. Black Rock ore which is similar to 2, but more free milling.In retrospect a number of the metallurgical successes of the past were short lived. Often flowsheets or 0perating practices were designed to solve a single metallurgical problem associated with the current ore being treated. As the ore changed the problem would vanish and the method originally taken to counter the problem could become unnecessary or deleterious to the treatment of the new ore. The general lesson learnt from-the past-is-that thetreatment of Mount Isa lead-zinc ore involves a number of equally major problems...

Jan 1, 1963

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

In this, the centennial year of The Institute, it is appropriate that the history of the Institute in New Zealand be recorded. I am indebted to John Dew, compiler of the centenary publication æMining People A Century - Highlights of the First Hundred Years of The AusIMM 1893 - 1993Æ, for many of the early historical references in this paper. In July 1892 the Amalgamated Mining Managers' Association of Australasia held its annual conference in Ballarat, Victoria, Australia, when it was suggested by the delegate from Broken Hill that the time had arrived for the establishment of an Australasian Institute of Mining Engineers. Resulting from this meeting at Ballarat, a Provisional Committee was formed at Broken Hill with the object of forming The Australasian Institute of Mining Engineers having the following objectives. To promote the arts and sciences connected with the economic production of the useful minerals and metals, the welfare of those employed in those industries by means of meetings for social intercourse, and the reading and discussion of professional papers with the circulation by means of publications amongst its members and associates the information thus obtained.

Jan 1, 1993

ABSTRACTMechanised cut and fill stoping in the Racecourse orebodies between II and 9 levels was started in 1964.Five stopes are in progress over the two level interval, extracting the full strike length (600-2,000 ft) of each orebody without transverse pillars.Each stope is served by a central 10 ft by 12 ft service intake ventilation raise and an 8 ft by 8 ft return air raise at each end of the stope. Each stope is divided into two sections for drilling. firing. mucking, and fillingto maintain steady production. All equipment is kept in the stope for one level lift stoping. Gardner-Denver 2 boom jumbos are used for uphole drilling and Wagner ST 5 Scooptrams for loading and transport to ore passes located in the footwall of the orebody. A Wagner PTIO is used for materials handling and scaling of the stope backs.Mill tailings, after one stage of cycloning are used to fill the stope, one section at a time. About 80 per cent of the water is removed by decantation while the remainder percolates through hessian-covered pipes and boxes.The ore is passed to 11 level where it is hauled by the 3 ft 6 in. gauge train to the tipple at the shaft area. The ore is crushed underground before hoisting to the surface.A performance of about 100 ton/manshift is achieved by the drilling, blasting, and mucking crews in the stopes.

Jan 1, 1968

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including û brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research program conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and alternative, cheaper, additives for cementing hydraulic fill.

Jan 1, 1971

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route.The Australian Atomic Energy Commission is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and· calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site.

Jan 1, 1970

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2007

The prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first was published in 1937; the second in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research.HARMLESSNESS OF ALUMINIUMAnimal experiments having served their purpose, it became necessary to consider means to test the discovery on humans. A question for immediate consideration was: Is aluminium harmful to man when inhaled as a fine powder? While the animal experiments were reassuring, since they conclusively showed the powder to be innocuous when breathed by animals, it was, nevertheless, desirable to have additional reassurance with regard to its effect upon human beings.Through the courtesy of the Aluminium Company of America and especially the valued interest in this problem displayed by that Company's Director of Research, Dr. Francis C. Frary, a study was made of the records pertaining to the health of a group of 125 employees who had for many years been engaged in the manufacture of finely powdered, metallic aluminium for the paint and ink industries. The conditions were such that these employees had inhaled varying and oft-times very dense concentrations of this powder daily over periods ranging from 6 to 23 years, the average 101 the group being 12 years. X-ray pictures of their chests showed no abnormalities attributable to aluminium. Their general health seemed better than that of the 3,000 workers in other sections of the plant. In fact, the early films of three employees in this group of 125 showed shadows suggestive of minimal tuberculosis, which shadows were not discernible in films taken after considerable periods of exposure to aluminium powder.The harmlessness of aluminium was; by this study, reasonably well established at the outset, a finding subsequently verified by Ontario research on humans.PROPOSAL TO TREAT HUMAN SILICOSISBased upon these findings, a proposal to treat silicotics with aluminium was discussed by officials of the Mclntyre Mine and the Banting Institute.

Jan 1, 1945

The notes from which this paper has been prepared were set down at the time of the author's departure from Australia in 1935. Mr. Frank Forman, Government Geologist of Western Australia, who has very kindly read the paper in manuscript, affirms that the views here set forth are now accepted by most geologists. Thus, Forman's recent presidential address before the Royal Society of Western Australia (1937) mentions sediments in the Kalgoorlie Series "including banded jaspers and jaspilites."While it may, therefore, be superfluous to belabour the question further at this time, Mr. Forman has encouraged the author to publish this paper as a summary or both past and present views.To those specially interested in the subject of the paper, a study of pertinent Plates attached to Western Australian Geological Survey Bulletin No. 71, 1917, is suggested.The type of rock which is variously called "jasper bar," jaspilite, or "ferruginous quartzite" is familiar to all mining men who have worked in the West Australian goldfields.In its typical form it is a "striped" rock consisting of alternate layers of white or pinkish silica with red to brown bands of iron-bearing silica.In the course of geological work in many parts of Western Australia I studied exposures of jasper bar and was repeatedly impressed with the similarity of much of the material to the sedimentary "banded iron formation" of Canada. It was, therefore, a surprise to learn that the jasper bars were not generally regarded in Australia as sedimentary horizons. It is true that Honman offered convincing evidence of the sedimentary origin of the jaspers...

Jan 1, 1939

By Misra V. N

Upgrading of a Koolanooka magnetite iron ore sample provided by Kingstream Steel Ltd was investigated using low intensity magnetic separation (LIMS) and reverse flotation. The ore contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina, with the main minerals in the ore being amphibole (42 per cent), magnetite (39 per cent) and quartz (14 per cent). The concentrate obtained after low intensity magnetic separation contained 66.6 per cent iron and 6.34 per cent silica with an iron recovery of 72 per cent. This concentrate was further treated by reverse flotation to increase the iron content and reduce the silica content to meet the requirements for direct reduction iron (DRI) feed grade.

Jan 1, 1999

The No. 2 Ore-shaft, at Mount Isa Mines Limited, involving the use of boreholes as ropeways for the upper portion thereof, constitutes, we believe, a unique feature in hoisting installations. The boreholes were sunk from the surface to a depth of 390 ft., thus eliminating the necessity of erecting the hoist at an underground location or construction of the shaft for this distance. Fig. 1, a diagrammatic cross-section through the shaft, shows the complete installation from the surface down to the first loading station below No. 7 haulage level.During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impracticable and uneconomical to continue deepening it to serve haulage levels below the present No. 5-level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5-level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin.Referring again to Fig. 1, it is apparent that the section above No. 4-level, if opened out to full shaft size, would be inoperative and would serve no useful purpose except, possibly, as a ventilation duct. Original plans therefore did not include continuation of the shaft above No. 4-level. Excavation of a hoist room upon No. 5-level; erection of sheave wheels just below No. 4-level, and a long inclined ropeway leading from the hoist to the sheaves, were incorporated in the general layout. Work on the lower sectionof the shaft had started when the idea of locating the hoist...

Jan 1, 1939

Residual aeolian placers (RAPs) are formed by the wind, by preferential entrainment and removal of small and low-density detritusfrom a pre-existing, typically sedimentary sequence containing heavy minerals. Heavy minerals that are resistant to chemical alteration and either soft and malleable (gold), or extremely hard (diamond, sapphire, ruby, etc), are concentrated as a residual on the wind deflation surface, typically in the interstices between larger resistant clasts. RAPs form preferentially in arid or semi arid areas, where the vegetation is sparse or absent, and where topography and surface gradients are low, but may also form on beaches and in periglacial environments. RAPs consist of a continuous or discontinuous, planar or gently undulating horizon of heavy minerals in a single-clast-thick pavement of resistant pebbles, cobbles, or boulders, which mantles the present topography or palaeo-topography. Extreme wind erosion and surface deflation may condense the full pre-existing sequence into a layer of heavy minerals only. The grade of RAPs is substantially higher than in the precursor deposit, and commonly much higher than those typically found in most other placer types. Aside from their general occurrence as a thin pavement of resistant clasts, the best indicators of residual aeolian gold placers are the presence of wind-eroded stones (ventifacts) on the pavement, and the distinctive and unique shapes of aeolian gold grains themselves. The shape of the gold grains is progressively transformed by sand blasting during placer development, from grains with thickened rims, to toroidal grains on which the rims are æsplitÆ and peened inward toward the grain centre on one or both of the grain sides, to hemispherical or sub-spherical grains that are fully encapsulated by the in-turned rims. Gold that has undergone aeolian shape transformation is difficult to entrain and transport away from the site of aeolian concentration by anything other than mass movement or glacial processes. It is also easily retained by commercial recovery plants of any configuration.

Jan 1, 2004

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

By B Mobilio, G B. Sharrock, J L. Lett, I Brunton, T Thornhill

Full-scale marker experiments at Cadia Valley underground operations have been ongoing for over 14 years. Initial marker experiments were undertaken in the Ridgeway sublevel cave (RW) (2002), and subsequently at Ridgeway Deeps (RWD) (2008) and Cadia East PC1 (CEPC1) (2012) block caves. Over 25 000 markers have been installed at the three caving operations to date (approximately 20 000, 3000 and 2500 for RW, RWD and CEPC1 respectively). These experiments aimed to quantify and assess the geometry of the extraction zone, development of the extraction zone over time, variability of flow behaviour and factors affecting flow behaviour in both the near and far field cave column. This paper discusses marker recovery results from the RWD and CEPC1 caves.With respect to the two cave operations, marker recovery in both the near field (markers recovered vertically within 70 m of the extraction level) and far field (markers recovered vertically above 70 m of the extraction level) indicates disturbed flow behaviour where marker recovery is not spatially uniform during material extraction. Two distinct patterns or transient behaviours in the extraction zone are indicated. For RWD (advanced undercut), early material recovery was close to the major apex, and expanded towards the centre of the drawbell as more material was extracted. The inverse was observed for CEPC1 (post undercut), where recovery occurred in the centre of the drawbell initially, and expanded outwards towards the major apex. This trend of recovery for the two operations continued in the far field. In the region above the major apex, recovery was observed for all heights, with no clear height of interaction zone (HIZ) indicated. All of these behaviours significantly deviate from both conventional ellipsoidal flow theory and Laubscher’s (2000) design guidelines. For this reason these new mechanisms are termed the Disturbed Extraction Zone (DEZ).For the CEPC1 marker experiment, electronic markers were utilised to investigate the vector movement of material in the near field. Marker recovery movement vectors in the near field indicate extraction zone widths in the order 30 m, with localised marker recovery outside this region (significant horizontal movement of material potentially due to cave muck pile rilling and blast burden movement). Analysis is ongoing for far field marker vector movement, and will be reported once additional marker recovery has been obtained.CITATION:Brunton, I, Lett, J L, Sharrock, G B, Thornhill, T and Mobilio, B, 2016. Full-scale flow marker experiments at the Ridgeway Deeps and Cadia East cave operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 141–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Nicol S. K, Firth B. A

Much effort over the years has been put into the task of devising parameters which adequately assess the metallurgical efficiency of mineral processmg operations. One of the most celebrated of these methods is the so-called "release analysis" method of Dell (1953) which tackles the problem in terms of an ideal separation based on sequential retreatment of the products and tails of a given separation process. Other methods have also been proposed by Jowett (1969) and by Holland-Batt (1971 ). While these procedures are appropriate to multi-component mineralogical separations, they perhaps do not lend themselves to the much more simple two-component systems encountered in coal preparation. However Dell (1962) has suggested the use of the term "specific profit" in coal preparation in order to assess the conditions that give maximum economic gain. Specific profit is derived from data relating washability data with equipment performance and operating costs. The procedure for using this criterion for comparative purposes is therefore somewhat cumbersome as is illustrated by its lack of widespread acceptance in the coal preparation literature.In contrast, an efficiency index, E, which is both simple and meaningful from the utilitarian standpoint, has been proposed by Tsiperovich and Evtushenko (1959a). This index is defined by the relation, E = Yield X Tailings ash/Product ash (1) A cursory examination of this parameter shows that it increases when yield and tailings ash increase and also when product ash decreases; all of which are desirable circumstances in coal cleaning operations.Further, it will be shown that slight variations in operation are amplified by this function which makes comparisons simple and direct.While the use of this index is quite extensive in the Soviet coal preparation literature for some reason it has not received wide usag~ elsewhere.

Jan 1, 1978

Plant for the production of sulphuric acid from pyrites flotation concentrates was commissioned at Cockle Creek during 1956, to meet increasing demands for commercial acid and superphosphate. Pyrite was chosen as raw material because of the uncertain supplyposition of imported brimstone and the desirability of utilising domestic sulphur.Desulphurisation of the pyrite is performed by two 40-ton per day roasters of the Turbulent Layer type operated under licence from the Badische Analin and Soda Fabrik (B.A.S.F.) organisation. These units are the first of their kind commissioned in the southernhemisphere. Pyrite is fed to the roasters in the as-received un-dried condition. Waste heat steam production is coupled with electricity generation within the plant. Sulphur dioxide is produced at comparatively high strengths and cleaned by conventional cyclone and hot electro-filter equipment.The acid unit has a capacity of 100 mono tons of sulphuric acid per day and includes cooling and wash towers, mist precipitators, a single stage drying tower, 4-pass oxidation section and absorption system.INTRODUCTIONSulphuric acid has been manufactured at Cockle Creek Works since 1913, when the first chamber nitration plant was commissioned. The raw material was brimstone roasted in Herreschoff furnaces. Since that time three additional chamber units have been constructed and have produced acid from brimstone, zinc concentrates, pyrites and -spent oxide, according to changing economic and supply factors.Three chamber units are still in operation. Contact processes have become increasingly important since the first Schroder-Grillo unit was commissioned in 1923. Six of these 5-ton per day units were operating in the mid-thirties, but have since been demolished. Two 15 ton Chemico hot gas contact units commenced operation in 1937 and 1938, and although modified, are still in service.The increasing demand over recent years for sulphuric...

Jan 1, 1957