Search Documents

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

Underground mining of the ore below the West Lyell open cut commenced in 1972 with the 10 Series stopes above rail haulage level. The third lift of stoping (30 Series) com- menced this year, and access to the 40 Series stopes is being developed. The method uses transverse open stopes with subsequent mass blasting of the rib and crown pillars and consequently there is sub- sidence and caving of the old open cut area above.

Jan 1, 1982

Optimisation of the Advanced Automation System at Inmet Mining's PyhSsalmi Mine, Finland

Sep 13, 2010

By J Bean

Iluka Resources Ltd developed the Jacinth-Ambrosia Mine (Jacinth) in the Eucla Basin during 2009 and 2010. In this arid climate the operation relies on hyper-saline groundwater from a palaeochannel for process and potable water supplies. The water is hyper-saline, acidic and mildly reducing, with high ferrous iron concentrations. Ferrolysis commences on exposure of water to oxygen, resulting in increased acidity and the conversion of dissolved ferrous iron to insoluble ferrihydrite. The unstable groundwater forces a careful balance between interventions relating to maintaining pipeline efficiency, corrosion protection and processing aspects. Providing an oxidising environment at the head of the pipeline will result in the precipitation of akaganenite and goethite in the pipeline, which over time reduces pipeline efficiency. However, sending too much ferrous iron forward may reduce processing performance.The processing plant experiences changes in water chemistry in response to the variability of iron concentrations and pH within the pipeline, and the spatial and chemical variability of ore. As the main orebody at Jacinth contains little buffering capacity a source of carbonate in the overburden is carefully used to allow the cost-effective control of process water pH.This paper highlights the importance of understanding the chemistry of saline make-up water, ore, and overburden when designing water treatment facilities and heavy mineral processing facilities.

Oct 5, 2011

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Player, R de Vries, E Villaescusa, H Saw, R Hassell

The use of cemented rock fill (CRF) for support of open stope walls has increased in the Australian underground mines operations over the last five years due in part to its low capital cost. In open stoping the exposed CRF masses require adequate strength and stiffness, in order to resist the forces and to limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or from development mining waste sometimes up to 1 m in diameter. However, the use of waste rock, which has a poorly graded particle size distribution may not achieve the required minimum target strength due to segregation and large air voids within the fill mass. This paper describes the optimisation of CRF strength by either crushing the waste rock or the addition of sand to the mix. Both methods increase the level of fines in the mix design. Cylindrical samples having 400 mm diameter and 800 mm heights were prepared for uniaxial compressive strength (UCS) testing. The UCS test was determined using the Western Australian School of Mines (WASM) large-scale static test frame. The laboratory results were compared with a database of large-scale CRF strength mixed without sand from a number of mine sites around Australia. The comparison shows a significant strength development in the CRF mixing with addition of sand for a given cement percentage. Due to the higher strengths achieved by the addition of sand and the crushing of the waste material these CRF types require less cement to achieve the same strength. This has the potential to improve the overall economics of open stope mining due to less dilution of the exposed fill mass.CITATION:Saw, H, de Vries, R, Player, J, Hassell, R and Villaescusa, E, 2017. Optimisation of cemented rock fill strength for open stope support, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By A Minchinton

With blasting, all far-field phenomena including, but not limited to, stress wave propagation, fracture, vibration and muck pile formation are intrinsically and irrevocably dependent upon near-field phenomena or mechanisms that we describe using physics-based mathematics typically transcribed into computer codes. The energetics involved in such near- to far-field transitions are not fundamentally relevant as they are simply progenitors of these processes.The notion of explosive energy as a descriptor for explosive or blasting performance is a case in point. These energies, which are generally used in blasting tables, are almost exclusively based on ideal detonation theory alone and do not include the influence of the rock, charge diameter, blasthole length and the late-time dynamic expansion that can be predicted using codes based on non-ideal detonation theory.With decoupled charges in presplits for example, the pressure drop between the charge and the blasthole wall can be simply described to first order using the energy relationship associated with adiabatic expansion. However, a more realistic mechanistic solution involves interacting fluids and turbulence leading to dynamic processes such as the channel effect.CITATION:Minchinton, A, 2015. On the influence of fundamental detonics on blasting practice, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 41–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Laskovski, T Nguyen

Flotation surveying can be an extremely powerful means of determining opportunities for circuit optimisation and benchmarking. The type of survey employed depends heavily on the nature of the information required from the survey. It follows then that the type of survey determines the type of samples required; however, regardless of the type, the success or failure of a survey is often dependent on the correct used of appropriate sampling techniques at each sampling point. For a successful flotation plant survey it is vital that the correct samples be collected at the correct time in respect to the feed and each other. This paper discusses the current best practice sampling methods used in flotation surveying and discusses in detail the ideal sample masses based on theoretical analysis. Comparisons with JKTech’s database of real plant operations will then be made.CITATION:Laskovski, D and Nguyen, T, 2014. An investigation of current flotation survey sampling, in Proceedings Sampling 2014 , pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Parbhakar-Fox, B G. Lottermoser, N Fox

"Determining the deportment of economic and environmentally significant elements in sulfidic mine materials (eg ore, gangue and waste) requires the use of advanced microanalytical techniques, including electron microprobe analysis (EMPA) and laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). Sulfidic boulders were sampled from an acid rock drainage impacted ephemeral stream adjacent to historical copper-silver workings at Baal Gammon, northern Queensland. The abundance and deportment of a range of trace elements and precious metals were analysed in these samples. Whilst many of these elements represent a potential environmental risk if leached from sulfidic rocks into streams in the surficial environment, significantly some of these elements (eg In, Sb and Co) represent specialised metals that are currently considered to be in critical supply.Sulfidic waste rock material at Baal Gammon is dominated by chalcopyrite, arsenopyrite, pyrrhotite and pyrite. Microanalytical investigations revealed that chalcopyrite contains significant quantities of In, Sn, Ag and Zn either substituted directly into the crystal lattice or occurring as discrete sphalerite and stannite inclusions. Arsenopyrite, which may comprise more than 50 per cent of some boulders, is notably enriched in Sb, Co and Ni but also contains inclusions of sphalerite, chalcopyrite and stannite. In contrast, pyrrhotite contains no trace elements of economic significance, but instead represents a likely contributor to acid generation during oxidation in the surficial environment. Trace metals (eg In, Sb, Co, Ni, Zn) are liberated during sulfide oxidation of these boulders in the surficial environment, generating a metal-rich, low-pH leachate.Fe-oxides precipitated as rinds on the surface of these boulders under low pH conditions also contain abundant As, Bi, Sn, Cu and Zn. Abandoned or historical mines represent potential sources of metalliferous drainage that poses potential environmental risks to water and habitats. However, sulfide-rich historical waste rock, stockpiles and processed waste (eg tailings) at abandoned mines may also represent significant sources of critical (eg indium) or other significant metals (eg Sn) that if liberated economically could improve environmental conditions in and around abandoned and historical mines.CITATION:Fox, N, Parbhakar-Fox, A and Lottermoser, B G, 2016. Critical and Deleterious Metal Deportment in Sulfidic Waste Rocks, Baal Gammon, North Queensland, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By MáAndrusiewicz, M M. Hilden, M S. Powell, P D. Kay, B Foggiatto

Circuits with unconventional and potentially more complex designs are predicted to become more common in the future as plant designers and operators look to process ores more efficiently. Ideas have been presented on how circuit design may be changed to utilise todayÆs technology to address tomorrowÆs challenges (Powell and Bye, 2009; Powell, Benzer and Mainza, 2011a). High pressure grinding roll (HPGR) installations in various configurations; application of preconcentration plants eg sorting, magnetic or gravity separation; and preweakening devices eg microwave processing; are all examples of technologies having the potential to deliver a significant reduction in comminution energy for ores amenable to these processes. Not only will future novel circuits contain equipment for which models are not as well developed (if at all), many will likely require the ability to respond to variations in feed, and interact with geometallurgical models requiring process adjustments when the ore characteristics change.In order to confidently simulate more complex circuits and accommodate variations in feed type, a significant advancement in modelling and simulation capability is required. This includes dealing with multiple components in the feed, accommodating different competencies of ore, utilising physical separation opportunities and tracking the grade reporting along the different potential processing routes. Developing the means to simulate complex circuits has been a key priority of a collaborative group of comminution researchers working to solve these challenges.Simulations are presented utilising a new configurable simulation interface called the model developers kit (MDK). The MDK is designed to accommodate multi-components and incorporate new models under development. These will be used to demonstrate the potential of flexible circuit design, based on measured ore properties and equipment performance.CITATION:Foggiatto, B, Hilden, M M, Powell, M S, Kay, P D and Andrusiewicz, M, 2012. Simulation of flexible circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 291-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By K Banerjee, C Dube

Veolia Water Technologies was contracted by a global coal mining company to design a retrofit acid mine drainage treatment facility using DenseSludge™ technology on a former coal refuse disposal site. The project constraint was to reuse current facilities in order to reduce additional capital work cost and avoid additional footprint requirements while improving treatment performance and reducing sludge production and chemical consumption. The initial installation of 454 m3/h served as a pilot plant to demonstrate the benefits of the process and ultimately provided design criteria for the new facility. The pilot demonstrated the benefit of the technology by reducing sludge volume by 90 per cent compared to conventional processes currently in use. The sludge that is reinjected into the mine contains less water, which reduces the volume of water that returns to the mine pool for treatment and mine water balance. Furthermore, the pilot plant reduced lime usage compared to conventional processes by operating at a lower pH set point, demonstrating steady pH control and stoichiometric lime utilisation.CITATION:Dube, C and Banerjee, K, 2015. Sludge conditioning technology to reduce sludge and the cost of acid mine drainage treatment, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By N S. Weerasekara, S Town, E Lessing, J A. De Torres

Philsaga Mining Corporation (Philsaga) had three main aims in converting their lining system from steel to metal cap. They wanted to increase mill availability, minimise localised high wear and optimise particle breakage to deliver increased efficiency within the milling circuit. Combining Discrete Element Method (DEM) modelling and empirical interpretation of liner wear resulted in a rigorous approach to understanding the impact of mill liners on overall mill performance. This new understanding was subsequently used to not only derive a new lining design to optimise performance and thereby improve overall plant economics, but also to guide further lining development.In this work, detailed DEM modelling, developed from actual plant data, together with optimising liner design for wear paved the way towards the installation of a Metal Cap lining system at Philsaga’s Ø6100 mm SAG Mill. The results were a reported increase in SAG mill throughput of 16 – 20 per cent due to improved breakage through more efficient use of installed power, a reduction in localised high liner wear with overall increase in liner life and reduction in liner replacement time. Site also reported an increased gold recovery of 2 per cent which the improved breakage might have contributed to. This paper will present the design challenges and compare the Metal Cap lining systems performance against Steel lining system. CITATION:Weerasekara, N S, Lessing, E, Town, S and De Torres, J A, 2018. Metal cap versus steel lining system at Philsaga Mining Corporation’s Ø6100 mm SAG mill, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 653–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By García B., Wolff E.

In Colombia, northeast of Antioquia, there is a gold deposit that has produced continuously since the middle of the XIX century, located within mining title RPP-140, property of Gran Colombia Gold Segovia (GCGS) since 2010. Mining materials are taken to the “María Dama” Processing Plant where 1500 tonnes of materials are processed daily. Before 2010, the previous owner of the mining title processed about 600 tpd and directly discharged almost all tailings, given that they had no capacity to put them into final deposits. El Chocho was conceived as a final tailings deposit to store the pulp produced by the processing plant; it was divided into two phases with two dams (upper dam and lower dam) given that the presence of illegal miners at the lower phase impeded a single dam design. A squatter impeded construction of the upper dam; so afterwards, starting at the higher end was necessary (owned by GCGS), building dam 1B to store tailings in pulp; after the squatter returned the lands to the owner (GCGS), construction of tailings dam 1A was required and thus complete construction of dam 1C or the upper dam. While all of this was happening, GCGS decided to acquire a 1500 tpd filter press which currently dehydrates tailings in order to take them to the valley controlled by dam 1A. Construction of dam 1A was designed following the containment wall model, made with geotextile tubes. These improvements generated reduced pressure on renewable natural resources because water is recirculated and less fresh water contributions are required; less pressure is placed on soil, flora and fauna because the area intervened for tailings storage will have a higher storage capacity and, as such, a longer useful life.

Jun 17, 2024