Search Documents

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By Eggins SM, Crawford AJ, Wallace ME, Falloon TJ

The Earth's Upper Mantle is dominantly peridotitic but in convergent margin regions, such as the S.W. Pacific, subduction of oceanic crust gives greater chemical and petrological diversity to upper mantle petrology and petrogenesis. Examination of currently active, Quaternary and Tertiary volcanism in the S.W. Pacific, particularly seeking information from ocean floor sampling to characterize the basement to island arcs and to investigate active spreading centres, consistently points to parental magmas of basaltic to picritic character. However, these parental magmas are chemically diverse and it is not possible to designate a characteristic 'island arc' or 'convergent margin' petrogenesis in the sense of a characteristic mantle source composition and a charactistic partial melting regime. In this respect, magma genesis at convergent margins contrasts with that at oceanic spreading centres. Our studies emphasize the importance of source peridotite ranging from 'fertile lherzolite' (i.e. compositions with 3-4% CaO, A12O3, 0.3-0.5% Na2O) to refractory harzburgite (

Jan 1, 1987

By G R. Hancock, M J. Saynor, J B. C Lowry, K G. Evans, M Narayan

Tools such as landform evolution models (LEMs) provide a means of predicting how a landform may evolve over extended periods of time. Here, we utilise the CAESAR-Lisflood LEM to assess a proposed rehabilitated landform of the Ranger Uranium Mine in the Northern Territory of Australia (Figure 1). The environmental requirements for the closure of the mine state that the final landform must be able to physically isolate tailings material from the environment for a period of at least 10,000 years (Australian Government, 1999). However, uncertainty exists as to the reliability of model predictions representing thousands of years.In this study, we use model predictions from an undisturbed pre-mine landform to calibrate the parameters used in model simulations of a post-mining rehabilitated landform over a simulated period of 1,000 years. Specifically, we vary environmental conditions such as rainfall, presence/absence of vegetation and surface particle size characteristics in a series of model simulations to determine their impact on the respective landforms, to revise model input parameters as required. A simulated period of 1,000 years was used as it represents a period in which long term landform evolution patterns and trends may be established and identified. CITATION:Lowry, J B C, Narayan, M, Evans, K G, Saynor, M J and Hancock, G R, 2018. Using an undisturbed landform to calibrate long-term predictions of the evolution of a rehabilitated landform, in Proceedings Life-of-Mine 2018, pp 133–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By C Vejrazka

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.The occurrence of air blasts is one of the principal mining hazards in block caving operations between the time of first undercutting and breakthrough of the cave to surface. As such, it needs to be managed continuously, and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. Unfortunately, there is little literature on how to practically approach air blast risk assessments in a way that can be incorporated in the day-to-day operation of a mine. Previous methods of assessing air blast risk were tedious and results were often unrepeatable.With the extension of the E48 Lift 1 extraction level, it was necessary to assess the air blast risk for the extension drives and develop operational guidelines for production from the extension. A review of the methodology for assessing air blast risks revealed substantial improvement opportunities.This paper outlines the principles used for air blast risk assessments at Northparkes Mines and the methodology employed to achieve efficient, repeatable and auditable results.CITATION:Vejrazka, C, 2016. Northparkes Mines’ current air blast risk assessment practices for block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 257–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R M. Arellano, D M. W Harney, M Makhuvha

Mineral resource and ore reserve estimates are founded on two sources of data: tonnage and grade. The tonnage is a product of volume and density; both of which are estimates. Density impacts numerous operational factors, which include, but are not limited to, mine design, mine planning, equipment selection and operational performance. Hence, density is a significant parameter and its determination requires similar care as the measurement of grade. Selecting an appropriate method to determine density, and ensuring its rigorous application, thus reduces risk and can improve operational performance, which in turn increases profit margin.Different Anglo American sites use a variety of practices and protocols to determine density, which is highly dependent on the physical characteristics of the orebody, local conditions and historical practices. Also, individual sites sometimes execute the same method in a slightly different way, which may also affect the outcome of the measurements. In order to gain a better understanding of how density is determined at Anglo American projects and operations, a review of these techniques was undertaken. The objective of the study was to identify and share good practices across the company, as well as to look for improvement opportunities, where applicable. Ten different methods of measuring density, applied to nine different commodities, were identified and described. An additional technique was recently developed by Anglo American Technical Solutions. The core pycnometer is a large gas displacement pycnometer capable of measuring density at high accuracy on full pieces of intact core.This paper provides an overview of methods used to determine density within the Anglo American Group, including quality control and quality assurance aspects. It is not the purpose of this paper to identify a preferred method, but to highlight the importance of choosing the best suited practice for a project or mine site. In addition, a case study comparing two different density determination methods applied to the same rock samples from the Los Bronces Copper mine was undertaken and the results of that study are presented here.Selecting the most appropriate method to determine density and comparing results from two or more techniques against each other, together with other suitable quality control procedures, is considered to be of utmost importance for all mining operations and exploration projects.CITATION:Makhuvha, M, Arellano, R M and Harney, D M W, 2014. Determination of bulk density in Anglo American plc, methods and impacts, with a case study from Los Bronces Mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By I Swane, R Rait, A Robertson

Geochemical assessment of mine waste materials prior to commencement of a proposed mining operation is a fundamental component of mine feasibility studies and the regulatory approvals process. Static and kinetic geochemical test methodologies are widely used to predict the geochemical nature of mine waste materials and to develop strategies for managing potentially æhostileÆ materials. These data can also be integrated with data from other fundamental studies such as hydrogeology to predict specific environmental outcomes and potential impacts at mine closure and post-closure.A case study is presented for a proposed open pit gold mine in Mongolia, which illustrates how geochemical, hydrogeological and groundwater quality data can be used as part of a geochemical modelling process to predict the final pit lake water quality over time. A series of static and kinetic test geochemical test programs were completed and acquired data integrated with hydrogeological and groundwater quality data provided by the proponent. A widely used geochemical modelling program (PHREEQC) was used to develop the geochemical model and predict water chemistry in the pit void after mine closure. Sensitivity analyses were completed to explore the effects on the model output of groundwater to leachate water ratio, pit wall rock type and climate.Modelling has indicated that pit void water should be pH circum-neutral at mine closure and should remain within Mongolian and World Bank water quality guideline limits under the modelled simulation most likely to occur in the field. Final void water salinity is expected to increase eight fold over 14 years after end of mine life due to a continuous flux of salts (particularly sulfate salts) into the pit lake whilst the pit lake volume will remain relatively constant due to evaporation and a slow recharge rate. Dissolved metal and sulfate salt concentrations in pit water are also predicted to increase over time and could be moderately elevated compared to applied water quality guideline values. Some of the metal concentrations, however, may be lower as these would be expected to precipitate at circum-neutral pH and greater. Recommended additional assessment work on the project when mining commences includes determining the magnitude of adsorption and co-precipitation of metals occurring in the pit void water/sludge system.CITATION:Robertson, A, Rait, R and Swane, I, 2013. Geochemical assessment of mine waste materials and prediction of final pit lake water quality at a proposed gold mine in Mongolia, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 165-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A M. Lechner, S Arnold, M J. Gillespie, P D. Erskine, D R. Mulligan, A T. Fletcher, A Gordon

Mine ecological monitoring schemes are often conducted only to address compliance and in some cases do not have the sufficient statistical power or understanding of ecological systems to assess, quantitatively, the meeting of rehabilitation targets or mine impacts. Monitoring schemes for rehabilitation commonly rely on analogue sites or premining baselines (reference sites) to assess whether rehabilitation sites are ecologically similar and thus successfully rehabilitated. In the case of monitoring for mine impacts, if the impacted sites diverge from reference data, the site is considered to be impacted. Fundamental to any monitoring scheme is testing the sampling design to ensure that it can detect these differences if they are present through adequate sample sizes (ie statistical power). However, a good understanding of the ecological system is required to ensure that differences detected are ecologically significant. Modelling ecosystem properties can provide a quantitative understanding of how ecosystems change over time and space, in response to natural environmental variations and thus aid in determining significant ecological differences. Furthermore, modelling methods can be used to predict future ecosystem states. Within the ecological literature, guidelines for robust statistical monitoring designs and modelling methods exist but are not routinely being used in the mining industry. This paper uses simple examples to discuss: problems with current compliance monitoring methods; importance of robust statistical techniques; and how modelling can assist rehabilitation assessment and guide monitoring schemes. The aim of this paper is to describe general monitoring and modelling methods that could be potentially used for mine site monitoring and closure assessment. These methods are often considered by mining companies as an extra expense that provide little practical benefit, and the domain of academia; however, engaging these methods may be more cost-effective in the long-run than conducting untargeted monitoring schemes that give no confidence to regulators on whether rehabilitation criteria have been met. Furthermore, monitoring programs in mining contexts provide a good opportunity to better understand long-term ecological patterns and test the application of more rigorous modelling approaches as the life of many mines tends to be greater than ten years.CITATION:Lechner, A M, Arnold, S, Fletcher, A T, Gordon, A, Erskine, P D, Gillespie, M J and Mulligan, D R, 2012. Embracing modern ecological methods - Monitoring and modelling for mine closure, not compliance, in Proceedings Life-of-Mine 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D A. Williams, P J. Chapman

The acceptable rate of rise of the tailings beaches on upstream-raised tailings storage facilities (TSFs) is critical to life of mine planning. This is illustrated through a case study in Western Australia presented in this paper. Accurate estimates of expected beach slopes, the maximum rate of rise at which the tailings can be placed, and the dry density that the tailings solids will achieve after deposition (stored density) are required in order to design TSFs that will allow upstream raises to be constructed safely and economically. Where operations have been occurring for some time, these three parameters are able to be measured and can be well-defined. If process plant throughputs are proposed to increase through mine expansion, for example, increasing the rate of rise of the tailings can compromise the potential for upstream TSF raising, thus influencing the viability of such an expansion, the timing for its implementation, and significantly increase costs.This paper outlines how rate of rise can be a key constraint, and that ‘rules of thumb’ that are typically applied may not result in the outcomes they were meant to achieve. An example of an experimental method to justify an increase to the ‘rule of thumb’ ~2.5 m/year limit for gold tailings in a semi-arid climatic setting is discussed, followed by rate of rise modelling that ultimately framed the decision-making process for a mine expansion. The rate of rise modelling method was adopted to carefully distribute tailings deposition across four TSFs, comprising nine separate tailings cells, in order to maintain appropriate rates of rise. The implications resulting from various deposition splits are presented, including the need for expansion. In addition, this paper outlines the effect of rate of rise on the state (density) of the tailings after deposition, and provides commentary on how anecdotally acceptable rates of rise, based on the aforementioned ‘rule of thumb’ of 2.5 m/year may not provide assurance of geotechnical stability through the tailings achieving a dilative state, as has been thought in the past. An example of the influence of rate of rise on the state of the tailings, with respect to air-drying and the critical state line (CSL) for the material, is presented. The data indicate that reducing the rate of rise may allow a higher dry density to be achieved through air-drying (evaporative desiccation), sufficient to move the material from the contractive to the dilative zone (i.e. from above the CSL, to sufficiently below it).CITATION:Chapman, P J and Williams, D A, 2018. The importance of rate of rise in life-of-mine planning of an upstream raised tailings storage facility – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 350–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R Strand, L Reading, G Keir

A major challenge in managing coal seam gas (CSG) water is predicting how much water will be produced as the industry develops. Klohn Crippen Berger Ltd (KCB) was commissioned by the Queensland Department of Natural Resources and Mines (DNRM) to develop a tool to forecast where, when and how much CSG water will be produced in the Surat and Southern Bowen Basins under various industry expansion scenarios.The water production tool (WPT) uses the Theis equation, a non-equilibrium groundwater flow equation that accounts for the effect of pumping time on well yield in confined aquifers, to predict water production volumes. Where multiple pumping wells are in close proximity, the required pumping rates for coal seam depressurisation are reduced. Therefore, pumping effects are projected spatially to assess interference effects between wells. Water production is then upscaled to the projected scale of the CSG industry within the Surat and Southern Bowen Basins.Two modifications were made to address the dual phase nature of CSG extraction (a transmissivity reduction factor) and the impact of weathering at the eastern margin of the Surat Basin (a ænear edge effectÆ factor). These factors modify relevant hydrogeological parameters in a consistent and defensible manner to more closely match observed water production.The WPT was verified by comparing results to equivalent Theis equation calculations and to type curves provided by CSG proponents. Calibration was achieved by varying the spatial distribution and intensity of the near edge effect factor in conjunction with a chi-squared analysis of residuals.The tool, which is now being maintained and further developed by the Centre for Water in the Minerals Industry (CWiMI), was built to balance numerical complexity against relative flexibility and simulation speed. The result is a tool that can produce statistically relevant results of prescribed scenarios to plan water handling and treatment requirements in discrete zones of operation.CITATION:Strand, R, Reading, L and Keir, G, 2013. Water production simulation tool for coal seam gas operations in Bowen and Surat basins, in Proceedings Water in Mining 2013 , pp 311-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By P Esteves, J L. Bechir, R Galery, C Senna, V Souto

The current moment experienced by the mineral industry is marked by a series of economic, social and environmental challenges. Among the main challenges, it is important to highlight the decreasing in ore grades with the gradual depletion of the existing deposits, the high volatility in international commodity prices and the operational inefficiencies in the mine, beneficiation, and metallurgical plants. In this context, mining companies are continuously looking for alternatives that minimize production costs and maximize overall production. In addition, recent tragedies involving tailings dam collapses in Brazil, reinforced the need for a more responsible, sustainable, and conscious mining, such as aiming the preservation and rehabilitation of the land environment. In this scenario, the Sensor-Based Sorting (SBS) technology is currently getting more space into the mining market. This separation technology aims the removal of gangue material in coarse particle size fractions, prior to comminution and concentration stages. As a consequence, the technology allows a smaller consumption of energy, water, chemical reagents and other inputs. Moreover, the sensor-based sorting is a dry processing technology and favors the reduction of fine material to be sent to the tailings. The aim of this paper is to provide information regarding the technical and economical evaluation of SBS technology applicability to a zinc silicate mining in Brazil. The project evaluation was performed in two stages: laboratory test work and the execution of a pilot plant. The execution of a pilot plant allowed the technology optimization, quantification of downstream process effects, such as a proper economic evaluation about the technology benefits. Keywords: Sensor-Based Sorting; Particle Sorting; Ore Sorting; Preconcentration; capital expenditure (CAPEX); operating expenditure (OPEX); zinc; comminution; dry processing.

Nov 10, 2020

By A Golsby

Gunite was invented in 1907 by Carl Akeley to repair a crumbling facade of the Field Columbian Museum in Chicago. The method used was to blow dry material out of a hose with compressed air and inject water at the nozzle as it was released. In 1911, he was granted a patent for his invention, the ‘cement gun’; the equipment used; and ‘gunite’, the material that was produced.The advantages of using the dry mix process is that the water content can be adjusted instantaneously, allowing more effective placement in overhead and vertical applications without using accelerators. The dry mix process is useful in repair applications when it is necessary to stop frequently as the dry material is easily discharged from the hose.This paper describes the applications and principles of the gunite pump system in underground coal mining and discusses why it is the preferred spraying system for both cement and plaster products.It also addresses improving productivity and examines dust, respirable crystalline silica (RCS) and health issues around gunite pump systems. The solutions include development of the latest componentry for current gunite pumps to improve their efficiency and allow their operation to be dustless.In particular, this paper addresses:why and where RCS is a problem in underground coal mininghow RCS hazards and its propagation can be managedhow the gunite pump system has become dustlesshow the gunite system has become more productivegunite occupational health and safety issues and how they have been solveda case study of gunite dry spraying.CITATION:Golsby, A, 2015. The development of a dustless dry gunite pump system in underground coal mining – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 41–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By G Burton, S Fityus, J Li, S Vaughan, D Payne

Daunia and Caval Ridge coal mines, owned and operated by BHP, have been co-disposing rejects and dewatered tailings within spoil dumps from the beginning of their operations in 2013 and 2014, with the purpose of minimising environmental impact and geotechnical risk. Following the recent large failures of tailings dams around the world, BHP Coal, through its Coal Tailings Program, plans to transition other coal mines to deliver “dry” tailings and produce mixed plant rejects (MPR) for inpit co-disposal. This will materially reduce future tailings dam risk exposure. Previous laboratory shear strength testing was conducted on rejects with a maximum particles size of 20 mm, and some concerns were raised that this might not represent the mechanical properties of the actual full particle size distribution (PSD) rejects. BHP was also aware that using different technologies to dewater the tailings, such as belt press filters (BPF) and solid bowl centrifuge (SBC), could produce thickened tailings which could significantly modify the physical behaviours of the MPRs, particularly the bonding between particles. Therefore, laboratory testing on both coarse rejects and mixtures of the coarse rejects and dewatered tailings (MPRs), with full PSDs, was carried out. Testing was performed using the large direct shear machine developed by the Australian Coal Association Research Program (ACARP) project C20019 in 2017, as well as a 300 mm diameter triaxial apparatus at the University of Newcastle (UoN). This paper presents details of the laboratory testing program and results for the rejects from the first studied mine of the BHP Coal Tailings Program. It compares the shear strengths measured at full scale with those tested on modified (scalped or crushed) specimens in the past; and discusses the tailings dewatering technique selection from geotechnical aspects based on the testing results, and finally presents some dump and tip head stability analysis results using the testing results.

Jul 1, 2021

By R Kroukamp, G Rech

CRONIMET Australia in cooperation with Speciality Metals International, the mining lease holder of the Mt Carbine Tungsten mine, have demonstrated the preconcentration and processing of large (>12 million tonnes) tailings and mine waste dumps on site in far north Queensland. The first stage of this project has proven the economic viability of preconcentration using sensor-based particle sorting whilst ensuring high recovery of industry critical tungsten minerals – wolframite and scheelite. Sensor-based sorting technology have enabled the production of a sorter product to feed the existing wet gravity plant ensuring higher recoveries and increasing concentrate production. Processing of 1,000 tonne low grade samples using the TOMRA x-ray transmission (XRT) ore sorter installed on site, has reduced the volume of material entering the downstream wet processing plant by up to 60%. The sorted 10-25mm size range produced the highest upgrade ratio (product/feed) of 24:1 and achieved sorter concentrate grade of 1.52% WO3, sorter waste grades below 0.014% WO3 and metal recoveries of up to 93.4%. The appropriately sized, barren sorter waste material is also sold as aggregate and other quarrying products and thus adding to the overall economic benefit of the project. The utilisation of the sorting technology on site has produced an economically viable project, significantly reduced capital cost, and reduced the time to market of the final tungsten concentrate. The next phase of the project includes design and installation of a larger two sorter plant capable of over 150t/h feedrate.

Nov 10, 2020

By I Ametov, S Harmer, R Alford

A process that allows selective flotation separation of low Cu/S ratio minerals (chalcopyrite and pyrite) from high Cu/S ratio minerals (bornite and chalcocite) from a mixed copper mineral concentrate under controlled oxidative-reductive potential conditions has been developed. The process has been extensively tested on samples with varying mineralogy using laboratory batch flotation tests and mini pilot plant trials.In this process, the mixed final copper mineral concentrate is purged with nitrogen, and then treated with sodium dithionite to achieve a slurry Eh in the -200 to -100 mV standard hydrogen electrode (SHE) range. Flotation was then carried out using nitrogen gas. As a result, a low Cu/S ratio concentrate (<1.3) and a high Cu/S ratio (>1.6) tailing stream were produced. QEMSCAN analysis of the flotation products showed that more than 85 per cent of the chalcopyrite and 95 per cent of the pyrite reported to the froth concentrate. Chalcocite and bornite were almost evenly distributed between the concentrate and tailing streams.Surface analysis studies, focused on the mechanism of separation, showed that at a negative redox potential xanthate and possibly dixanthogen are the dominant hydrophobic species on the surface of chalcopyrite and pyrite. As a result, the flotation of these minerals remained unaffected. In contrast, a much lower concentration of xanthate species on the surface of chalcocite and bornite particles was observed. Therefore, it is likely that at low Eh the copper xanthate complex desorbs from the chalcocite and bornite surfaces, causing a decrease in surface hydrophobicity and the diminished floatability of chalcocite and bornite.CITATION:Ametov, I, Harmer, S, Grano, S and Alford, R, 2014. Selective flotation of chalcopyrite and pyrite from a mixed copper mineral concentrate under controlled redox potential conditions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Lapwood, S Pal, M Pascoe

The devastating failure of Dam I at the Corrego do Feijao iron ore mine near Brumadinho in Brazil on 25th January 2019 left at least 270 people dead or missing. In the immediate aftermath of this event, many mining companies commenced reviews of their tailings and water storage facilities (T&WSFs), and Rio Tinto was no exception. Rio Tinto has an interest in over 250 T&WSFs across 47 sites in 13 countries as owner-operator, as managing JV partner, and through non-managed partnerships and other ownership arrangements; T&WSF experts from Rio Tinto’s Surface Mining Centre of Excellence visited the sites in order to complete Technical Risk Reviews of each facility. These reviews looked beyond the day-to-day operational aspects of T&WSF management, and the site’s compliance with local regulations and Rio Tinto’s internal D5 Standard – Management of tailings and water storage facilities, in order to provide a strategic, second line of assurance perspective. The reviews focused on design and construction; operational controls; risk control framework; and competencies and capabilities of personnel involved in the design, operation and closure of the facilities. Additional activities were carried out in parallel with these reviews, including the development of a consistent approach to dam break studies; the public disclosure of information on Rio Tinto’s tailings storage facilities and their management; and contribution to external programs such as the initiatives being co-ordinated by the International Committee on Mining and Metals. This paper provides an overview of the tailings and water storage assurance work undertaken by Rio Tinto’s Surface Mining Centre of Excellence Tailings Validation Taskforce to date; work that will continue to improve governance and assurance for all of Rio Tinto’s T&WSF.

Jul 1, 2021

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013