Search Documents

By P Jones

Fosterville Gold Mine is an underground operation located approximately 20 km northeast of Bendigo and 170 km north of Melbourne. Fosterville is the most productive gold mine in Victoria, producing over 100 000 ounces of gold annually. Access to the underground is via two portals cut into previously mined open pits. Fosterville is 100 per cent owned and operated by Northgate Minerals, a gold and copper producer with mining operations, development projects and exploration properties in Canada and Australia. (Northgate Minerals Corporation, 2010).Underground operations commenced in 2006 with ore production focused on three orebodies – Phoenix, Ellesmere and Falcon. Primary ventilation to the existing operation is provided by wall mounted exhaust fans located underground. This system provides approximately 220 m3/s of primary ventilation to the operations with intake achieved through the portals. Exploration drilling during recent times has uncovered another lode, the Harrier orebody, located 2.2 km to the south of the existing workings. Due to the location of the new Harrier orebody, vent analysis revealed the requirement for a separate source of primary ventilation to service Harrier. Figure 1 shows a current underground long section and the location of Harrier in relation to the existing workings. A number of options were considered, including a parallel decline from one of the existing two portals, however, a 4 m diameter, 350 m deep surface ventilation shaft was selected as the most suitable and feasible option for the mine.In December 2009, geotechnical drilling commenced to determine the most suitable location for the shaft. Site locations were constrained by a number of factors including interaction with current and planned surface infrastructure as well as proximity to nearby community members at the southern end of the mining lease. Results from the geotechnical drilling indicated that the majority of the proposed shaft would be suitable for a 4 m raise bored shaft. However, the top 40 m of the proposed shaft were deemed unsuitable for raiseboring due to zones of weakness that would likely influence the stability of a 4 m diameter shaft (Robinson, 2010). Following independent geotechnical advice and input from experienced raiseboring contractors, it was decided to construct a 40 m presink prior to raiseboring activities.A crane mounted auger was chosen as the preferred method to construct the presink. This method differs substantially from traditional blind sinking methods which are highly labour intensive. The auger, or drill, is designed and built to be attached to a crane base using engineered pivoting cradles. The auger is suspended from the crane jib by pennant ropes attached to hydraulic rams. The auger applies rotation and axial loads to the drilling tools via a telescopic steel bar (Kelly Bar). Drill tools are attached to the bottom of the Kelly Bar and comprise an assortment of drilling buckets and reaming barrels. Drilling buckets cut in situ material and collect the spoil for removal and are used for the excavation of the ‘pilot hole’. Reaming barrels are used to expand the diameter of the excavation by directing cuttings into the pilot hole which are then removed by the drilling bucket. In June 2010, the presink was constructed utilising a crane mounted auger with support to the shaft walls applied via a remote fibrecrete unit. The excavation method involved cutting a series of smaller diameter holes (2.4 m wide) before reaming out to the final diameter (4.7 m wide) in 4 - 5 m vertical increments. Fibrecreting activities were carried out on the backshifts, to ensure the stability of the excavation and minimise interaction between the two units. The presink was completed on time and offered many advantages compared to traditional blind sinking methods, including safety, costs and timing. This paper will examine the benefits of this method as well as lessons learnt and future applications in the mining industry.

Mar 21, 2011

By D J. Brake

Faced with the need to improve workplace conditions in both its development and production headings in its existing K1 orebody, as well as its new K Link and K2 orebodies, the Kencana mine in Indonesia took the novel approach of reversing the ventilation on most of its access ramp by outcasting up the ramp to the portal. Working levels were then fed with fresh air via auxiliary fans sealed into the current surface ‘egress’ intake raises (ladderways) or another small surface intake raisebore rather than from fans hung in the ramp as in the past. Outcasting the portal provided a substantial increase in the total mine exhaust capacity allowing fewer levels to be ventilated in series and significantly improving conditions, especially in the most difficult workplaces to ventilate. It also reduced the consequences if there was to be a fire on a vehicle in the ramp. The same system using the ramp as an exhaust is also intended to be used as part of the final ventilation solution for the new K2 orebody which also uses a novel single surface ventilation shaft that is vertically split into separate intake and exhaust compartments using a concrete brattice. Using the main ramp as an exhaust has potential application in many other operations in Australia using surface ramps which otherwise frequently suffer from overuse of series ventilation circuits and poor working conditions at the mine bottom.

Mar 21, 2011

By Hill G

The Boddington Gold Mine (BGM) is managed by Worsley Alumina Pty Ltd (Worsley) and is located 110 km south-east of Perth, Western Australia. The gold mine, which has operated since mid-1987, was originally constructed to treat 3 Mtpa of gold bearing oxide ores, has subsequently been expanded to treat 7 Mtpa and is presently one of the largest gold producing operations in Australia.During 1990 a Supergene/Basement Plant was constructed to treat 250 000 tpa of copper supergene and hypogene ores and basement ores which contain significant gold grades and which are encountered at the lower levels of the existing oxide orebody. The SupergeneBasement Plant has the versatility to treat a wide range of ore types, producing both gold bullion and copper-gold concentrates. It is a stand-alone facility adjacent to the existing 7 Mtpa gold plant.

Jan 1, 1992

By Kato T, Eguchi M, Seino T, Itagaki K, Kimura T, Muto T, Shimizu T, Kobayashi T

Behaviour of minor elements in the dust collecting system connected with fluidized bed roaster for zinc concentrate was investigated by use of the bench scale experimental appara- tus. The dust collecting system was consisting of two dust chambers, hot electrostatic precip- itator, washing tower, mist electrostatic pre- cipitator, drying tower, absorption towers and potassium permanganate solution towers. Some volatile elements such as lead, cadmium and arsenic tend to concentrate in the fine calcine obtained in hot electrostatic precipitator especially in the case of the roasting with insufficient air supply. Special attention was paid to behaviour of mercury. In the roasting tests for plain zinc concentrate, it was considered that most mercury volatilizes at first as elemental vapour in the roaster, but with decrease in temperature of gas around a half of mercury forms compound, and both elemen- tal and compound forms of mercury were found in the gas stream. Elemental mercury is of course difficult to be trapped in the dust collecting system. To promote the compound formations, some additives for concentrate, such as selenium and halogens were effective, especially selenium of a few times equivalent to form HgSe repre- sented complete conversion of mercury from elemental to compound. To clarify the behaviour and removal mech- anism of mercury, various small scale laboratory tests were also carried out. It was confirmed that mercury sulfate formation is possible if temperature and flow rate are adjusted adequate- ly for gas stream consisting of 02-SO2-N2. To trap elemental mercury, various substances were tested, and excellent results were obtained with selenium. Satisfactory results were obtained with a selenium disc heated at 100 to 200¦C in a mercury containing gas stream. Also, applica- bility of scrubbing method with SeO2 solution was investigated, and the solution containing a few hundred ppm SeO2, 0.01 per cent additive and 6 per cent H2SO4 proved to be satisfactory.

Jan 1, 1980

By J Geronimo, P Kumar, Z Yussupova, M Yahyaei, M Powell

This work goes beyond the general perception of how the well-known mine to mill process can be applied, by applying deeper knowledge along the mining chain. Grade deportment and dilution are considered at the mining stage, and modelled with the new SMI blast movement simulator, linking with the block model data. Assessing the shift to a considerably more competent section of the orebody is quantified via substantial milling trials at standard and higher-intensity blasts. These were stockpiled for batch processing through the mill to ensure feed integrity. The trial work included operating the mill at widely different fillings to develop Grindcurve milling responses. Additionally, model informed process control is initiated via a mill prediction tool.It has been found that accounting for blast movement for the higher intensity blasts could generate additional value of around $1.5M per blast. With the high-intensity blast and changing mill control, the plant was easily able to exceed projected mill throughputs with the far more competent Pipeline ore. Strategies to shift the workload and debottleneck the milling circuit were proposed and proven during the milling trials, demonstrating an increase in throughput of 7 per cent despite running at a lower SAG mill speed, and potential of 16 per cent for increasing the SAG mill to standard operating speed. A number of process improvement opportunities have been identified to enhance current productivity and ensure long term capability to process the considerably more competent future ores. All of this is being linked in with the major digitisation program at the Barrick Cortez site, with an objective of linking all the data into a mine-wide process optimisation system, that can embed the processes by providing process-wide data access and production support via the future dynamic models linking ore body knowledge to productivity along the full process chain.CITATION:Powell, M, Yahyaei, M, Geronimo, J, Yussupova, Z and Kumar, P, 2018. The designed approach to mill liner optimisation – experience at Pustynnoye mine, Kazakhstan, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 595–612 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Most coal mines in Chongqing Area are highly gassy mines and liable to outburst of coal cnd methane. In order to harness mine environment and raise the Prodction capacity, methane predrainage is generally taken as a main preventive measure against outburst by all mines. In the recent ten years, the drainage volume per year has increased from 38.25 million m3 to mote than 100 million m3 with a volume over 12 m3 per tome of coal. In some mines, the draining rate is approaching to 50 percent, the rate in mining districts is up to 60 to 70 percent. The predrainage volume accounts for one fourth of total drainage volume. All these have effectively prevented the occurrence of coal and methane outbursts.This is the current situation of methane predrainage in coal mines in Chongqing area, the methods of predrainage to prevent outbursts and related parametres comprise:1. methods, technologies, supervision and effect of predrainage in different geological and mining conditions,2. the change of methane parametres pre-and post-drainage and the analysis of the effect of methane predrainage to prevent outbursts, and3. ways to improve the effect of methane predrainage.Thus the safety, reliability and production of Changqing Coal Mines will be enhanced.

Jan 1, 1991

By P Bergin, J M. Galvin, J Harris, J Li, P Kirsch, M Shi, B Hebblewhite, B Whittaker, R Mitra, D Sprott

Controlling unwanted ground movement is critical in mining as well as many other highly hazardous environments, such as construction and tunnelling. Sharing knowledge about effective hazard management is paramount to improving health and safety and operational outcomes across industries, and some industry sectors have embraced this openness as part of the way that they do business. In 2010, the Australian Coal Association Research Program funded the RISKGATE project to build a body of knowledge for managing a broad range of hazards across mine sites, lease areas and mine infrastructure within a mine-life or product life cycle perspective (eg from exploration through to decommissioning, or design through to operation). The RISKGATE body of knowledge was assembled from Australian coal industry experts through a semi-structured bowtie analysis-based action research workshop cycle. By capturing operational knowledge from industry experts, RISKGATE serves to provide a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper presents an overview of RISKGATE topics within the geological and geotechnical domain (strata underground, ground control open cut, outburst, coal bumps and bursts, tailings dams and inrush) with a summary of individual topic structures, as well as showing the contrasts and inter-relationships between these ground management topics. The online user can access information about the causes, controls and consequences related to a priority unwanted event (ie the point at which control of energy is lost) and use this information as a prompt for the development of risk assessments, incident investigation, audits of practice/plans/procedures and for training and development.The paper concludes with a discussion of how RISKGATE can be adapted to other mining domains (eg coal outside of Australia, hard rock mining worldwide, construction, tunnelling) and the opportunity for application of this body of knowledge and the RISKGATE action research process for knowledge management in other highly hazardous environments.CITATION:Kirsch, P, Hebblewhite, B, Sprott, D, Harris, J, Li, J, Shi, M, Whittaker, B, Galvin, J M, Bergin, P, Mitra R and Williams, D, 2014. RISKGATE – shared coal mining knowledge for managing risks across ground management, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K L. C Gontalves

In 1999, the Mineral Development Centre of CVRD (CDM) acquired a flotation device referred to as Mini Pilot Plant (MPP), which is able to run continuous flotation tests with drill core samples. Since then this equipment has been used to define the flotation circuit and process conditions during the pre-feasibility phase of CVRDÆs copper sulfide projects. Until now, the MPP results had not been validated for an industrial flotation operation. The present work consists of a comparison and correlation of the results from a flotation MPP and an industrial plant. In order to make this comparison, an industrial plant was completely sampled and the feed ore was tested on bench scale and on a MPP. The metallurgical and mass balances of each test were used for the comparison.

Jan 1, 2005

By Esaki M, Nishimura K

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

By A Moreira, A B. De Souza, S Latchireddi, E Faria

Material transport plays a significant role in the efficiency of horizontal grinding mills - autogenous (AG)/semi-autogenous (SAG)/ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a greenfield milling operation at Mirabela MineratpoÆs SantaRita Nickel operation located in north eastern Bahia in Brazil. This grinding circuit was commissioned in October 2009, was designed as a typical SABC circuit to grind 4.6 Mt/a (575 t/h) to produce a P80 of 125 ¦m with ten to 12 per cent ball charge in the SAG mill. However, it has been operating as an ABC circuit without any grinding media in SAG mill. The nameplate design capacity was achieved in few days and was gradually increased to an average of +800 t/h, still operating in ABC mode. The Santa Rita grinding circuit consists of one 30 ft + 15.4 ft 8.5 MW SAG mill fitted with Outotec patented Turbo Pulp Lifters (TPLÖ) in closed circuit with a HP400 short head pebble crusher and one 20 ft + 28.4 ft 5.5 MW Ball Mill in closed circuit with a Warman cyclone cluster fitted with 10 + 26 in CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimisation and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed.CITATION:De Souza, A B, Latchireddi, S, Moreira, A and Faria, E, 2012. Application of turbo pulp lifter in greenfield operation - Mirabela SantaRita nickel operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Designing for early access to deep orebodies is an essential driver for improved project payback. Vertical shaft sinking techniques have been developed to allow concurrent mine level excavation while continuing to sink. Project cash flows can also be improved when simultaneously deepening existing shafts beneath operating hoisting systems. Further economic advantage has been realised through creative sinking sequencing in twin ventilation/service shaft projects. A fourth technique to reduce project schedules involves partial shaft barrel equipping allowing unrestricted access to construct stations and continue with level installations. This approach reduces interference with barrel sinking activities to insignificant proportions. This paper reviews how these approaches have added significant value to actual shaft sinking projects, as assessed from a contractorÆs perspective, and discusses some of the practical issues to be addressed when planning future projects. Designers need to take cognisance throughout all project engineering phases of the adage that you are only sinking when cleaning the face. Cleaning can only be sustained when there is sufficient hoisting capacity.

Jan 1, 2005

By Savage E. N

The porphyry copper minerals of Melanesia occur within a host of narrow veinlets in predominantly quartz diorite stocks or as contact metasomatic masses in skarns adjacent to the intrusion. Some 90 per cent of the constituent minerals comprise pyrite or marcasite, chalcopyrite, and magnetite with the remainder mainly bornite and hematite with accessory rutile and chalcocite together with several trace minerals. Gold is found mainly as inclusions in chalcopyrite, and minor molybdenite occurs likewise.Of particular significance is the persistent occurrence of accessory rutile of hydrothermal origin intimately intergrown with chalcopyrite. The rutile occurs relatively late in the hydrothermal sequence and upon weathering of the deposit may be released on a cumulative basis possibly in sufficient amounts to constitute a particulate pathfinder mineral which may aid in prospecting.Rutile is present in all the Melanesian occurrences studied and is also prominent in several American deposits.The porphyry copper mineralogy is characterized by the presence of accessory hydrothermal rutile intergrown with chalcopyrite.

Jan 1, 1975

There are a number of mineral processing operations which produce at some point a stream of hot particulates. At today's energy prices it becomes important to recover the energy held in the hot particulates. Sometimes it is convenient to use gas, e.g. in air pre- heating, and this will be appropriate in some circumstances. There are cases where it would be very useful if energy in the hot processed particles could be exchanged to the cold feed solids. This can be achieved within appropriate limitations by countercurrent heat exchangers comprised of parallel channels which contain, alternately, fluidized solids of 'hot' and 'cold' streams respectively. A pilot- plant has been built. Some calculations relating to industrial application will be Presented.

Jan 1, 1981

By C Munro, S Emery, M Flynn, K Tan

"AEROPHINE® 3418A Promoter is a well-known and widely used collector and is an industry standard for its excellent selectivity and efficacy in the processing of complex polymetallic sulfide ores, particularly those containing silver. Until now, however, it has not found widespread use in primary nickel flotation.In an effort to increase nickel recovery without compromising selectivity over iron sulfides, Western Areas Forrestania Nickel operation trialled the use of AEROPHINE® 3418A as a secondary collector at low dosage. A series of ON/OFF trials were conducted, with the finding that a very low dose of AEROPHINE® 3418A increased nickel recovery by 0.6 per cent compared to using xanthate alone.This paper provides a brief operational history and overview of the Forrestania operations, a description of the trial and an analysis of the results.Citation:Emery, S, Flynn, M, Tan, K and Munro, C, 2016. Aerophine® 3418A Promoter as a Secondary Collector to Boost Nickel Recovery at Forrestania Nickel Operations, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Nell, J Petersen, X C. Goso

The feasibility of increasing the deportment of titanium species and the stability of the pseudobrookite solid solution (M3O5) in a titaniferous slag was investigated, to facilitate the valourisation of titaniferous slags. Thermochemical simulations using FactSage™ software, ver 8.3 (by Thermofact/CRTC and GTT-Technologies), and equilibration-quench experiments were conducted using an appropriate synthetic titaniferous slag composition in an oxygen partial pressure (pO2) ranging from air to 10-16 atm under non-isothermal conditions. The temperature-pressure phase stability diagram for the synthetic slag containing 37.19 per cent TiO2, 19.69 per cent SiO2, 13.12 per cent Al2O3, 16.00 per cent CaO and 14.00 per cent MgO showed that the spinel solid solution (M3O4) was the primary phase until a pO2 of 10-10.5 atm, thereafter M3O5 was the primary phase until a pO2 10-13.2 atm. M3O4 again was the primary phase between a pO2 10-13.2 and 10-16 atm. The changeover of the primary phase coincided with an increase in the liquidus surface. When cooling the slag in a pO2 of 10-16 atm, M3O5 crystallised as a ternary phase that showed a rapid increase in mass while that of the primary M3O4 phase decreased and that of the secondary perovskite (CaTiO3) phase increased at a slower rate. At 1300°C under sub-liquidus conditions, the contents of M3O5, M3O4 and CaTiO3 were about 20 per cent, 15 per cent, and 11 per cent, respectively. Experimental results showed that the Ti3+/Ti4+ mass ratio in the M3O5 phase, ie a measure of the reduction of titanium species, is not considerably sensitive to equilibration temperature in the reviewed range. Slow cooling and minimum/no oxidation during cooling of titaniferous slag would increase the deportment of titanium species to, and the growth and stability of the M3O5 phase.

Jun 19, 2024

The Australian Coal Combustion Testing and Research Facility has been operating commercially for one year and during that period coal product evaluations have been conducted on behalf of four coal companies and one electricity commission. The facility is equipped to assess the behaviour of steaming coal in milling, combustion (including flame stability, burnout and heat transfer), ash deposition and erosion, fly ash collection and gaseous emissions. The relevance of the results of the pilot testing to industrial practice was demonstrated during the calibration of the facility using four coals burnt in Australian power stations. The calibration coals were from the Tarong and Gladstone Power Stations in Queensland, tluja Power Station in Western Australia and Bayswater Power Station in New South Wales. Also an opportunity arose to visit an overseas power station to observe a full scale test burn using one of the early coals tested on a commercial basis in the combustion test facility. The calibration trials showed excellent agreement with industrial coal performance in t:orms of flame stability, turndown, carbon burnout and gaseous emissions. Encouraging correlations were also found in the case of furnace radiation, boiler deposits (slagging and fouling) and electrostatic precipitation. In the case of the last group the only real reservations about the correlations are due to the non-availability or qualitative nature of results collected around the power stations. In all cases there is a high degree of confidence in the facility's ability to predict the relative performance of different coals and in some cases direct numerical predictions can be Made.

Jan 1, 1987

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

By P K. Singh

Recent advancements in understanding the detonation process are noteworthy, but they are still based on somewhat hypothetical situations. The actual variables that are essential parts of normal blasting practice have not yet been taken into account in such treatments. These include the various initiation practices employed to detonate a column of explosive, from single point initiation to multi-point initiation in blast holes, and the effect on detonation characteristics of both detonators and explosives under multi-deck and multi-hole blasting conditions. The in-the-hole velocity of detonation (VOD) of an industrial explosive is dependent on explosive’s charge diameter and blasthole diameter. The relationship between blasthole diameter and VOD provides a fundamental guideline to the rate of energy conversion and energy release within the detonation front on the interaction of explosives with the confining medium.The in-the-hole VOD of explosives was measured at four experimental sites in India for different blasthole diameters, ie 150 mm to 311 mm, but for identical explosive composition being same particle size, density, viscosity and loaded into blastholes with the same degree of confinement. The results of the studies demonstrated that there is definite relationship in in-the-hole VOD of the explosive and the diameter of the blast hole. The study also confirmed that the explosives initiated with concentrated boosters yielded higher VOD in comparison to those explosives that were initiated with multi-point priming. The measured increase in VOD of explosives for increasing diameter of holes was up to 24 per cent. The rate of change in in-the-hole VOD of explosives increases with increasing blasthole diameter. It can be further stated that the in-the-hole VOD of the explosive reaches a fairly constant value after reaching a limiting/threshold diameter of 311 mm.

Nov 8, 2011