Search Documents

By R Sridhar, M Fe, W G. Bacon

The problems of magnetite build-up have plagued the non-ferrous pyrometallurgical industry for many years. To better understand these problems, a study was undertaken to determine the thermodynamic variables that affect the behaviour of magnetite under different smelting conditions. Equilibration studies were performed in the nickel smelting systems of matte-gas and matte-slag(silica saturation)-gas. The relationship of thermodynamic variables such as temperature, sulphur and oxygen partial pressure and matte grade on iron and magnetite activities were calculated and the significance on smelting parameters such as metal losses and partition coefficients were defined. The experimental data from this study were employed to develop practical methods which could be used to control the build up of magnetite, as well as to obtain additional metallurgical benefits. In general, a lower sulphur partial pressure and higher temperature operation was shown to enhance the metallurgical benefits of nickel smelting by decreasing the magnetite activity. Operating in this manner can also have added benefits such as higher metal recoveries, more efficient vessel utilisation and efficiency and lower smelter emissions at equivalent or higher primary furnace matte grades.

Jan 1, 2000

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

By A Bouazza, J Kodikara

In this study, 23 samples of leached ash (LA) were collected from an ash pond at Loy Yang Power Station and geotechnically characterised. The samples were collected at various depths and locations within the ash pond on two separate occasions in order to account for the full variability. The LA within the ash pond at Loy Yang Power Station (LYPS) was found to vary in texture from silt to sand, depending on the location from where the sample was collected. Samples collected near the ash pond inlet discharge point, for instance, contained more than 50 per cent sand sized particles and were subsequently classified under the Unified Soil Classification System (USCS) as silty sand (SM). Further downstream of the inlet discharge, the LA became progressively finer and was classified accordingly as elastic silt (MH) when the sand content became less than 50 per cent. Basic geotechnical testing revealed that the LA from Loy Yang Power Station was generally acceptable as a landfill cover material. The permeability of LA, however, was generally too high for prescriptive covers, (ie resistive covers that generally rely on the impervious nature of the material to control percolation). Alternative covers, generally rely on the store/release function of a capillary or monolithic barrier to prevent percolation into the landfill. Subsequently, a material that can maintain a high water storage capacity while at the same time, readily allow infiltration and evapotranspiration is required for an alternative cover. Sandy silt and silty sand are optimal soils for alternative covers, as they do not yield water to gravity forces, but do give up most of the water in their pores when subjected to high-matric suction (Kavazanjian, 2001). The effectiveness of alternative covers is ultimately assessed using computer models, such as UNSAT-H and HYDRUS-2D, to rigorously perform water balance calculations. Prior to using a computer model to determine the highest possible percolation in the worst climatic conditions, it is necessary to select the most appropriate materials. This paper suggests a method to screen available materials for use as an alternative cover material on the basis of the soil water characteristic curve (SWCC).

Jan 1, 2003

We are moving into an era where we experience the consequences of the skills crisis û namely many resource models have been generated by inexperienced people under pressure to deliver high quality resource estimates in unsupported environments, often without technical mentors. These resource models form the basis of our decision to pursue actual mining. This begs the question: how valid are the resource models that form the basis of our mining decisions? This paper presents various model validation tools such as comparison of input and output statistics, swath plots, sectional or bench comparisons between drill holes and models as well as a variety of other approaches. Each model validation tool currently used in industry is examined:how the tool generates results,what assumptions exist,what constitutes a pass/fail in the test, and what interpretations to consider when using the validation tool. Each validation toolÆs suitability and the inherent flaws in the underlying assumptions are also discussed. These are supported with examples of good versus bad validations. Our principles based reporting codes provide flexibility in how models are generated and what approaches and/or parameters are used to generate resource estimates. This flexibility works well when used by experienced practitioners. However, our reporting codes assume a level of experience not always available in the current skills crisis. This paper seeks to provide minimum model validation prerequisites for model acceptance and suitability, regardless of the resource analystÆs experience. As we move forward, our immediate challenge is to ensure our baseline resource models are material, transparent and competent.

Jan 1, 2009

The use of scrapers in mining and earthmoving operations is not new, in fact they are one of the earliest methods of bulk earthmoving. A single machine which can load, haul, and dump material with a minimum of ancilliary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancilliary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

A key issue in maintaining the mining industryÆs social contract to access community-owned resources, is the need to be able to demonstrate professional management of resource extraction and the risk associated with mining hazards. Significant failures such as disease relating to coal dust and asbestos and mine disasters such as Moura, Appin and Gretley have resulted in judicial and legislative interventions that respond to the community outcry but do not necessarily effectively manage the longer term risk in a sector driven by new technology. With the implementation of recent amendments to the Queensland Professional Engineers Act, senior engineers in all industries including the mining industry are required to be registered and to demonstrate that they have æmaintained competency in the practice of engineering in the area of engineering for which the (engineer) is ... registeredÆ. This may be facilitated through a report produced by an æAssessing EntityÆ. These entities are approved by the Minister on advice from the Board of Professional Engineers, Queensland. Engineers Australia and The Australasian Institute of Mining and Metallurgy (The AusIMM) are the two professional bodies approved as æassessing entitiesÆ charged with facilitating successful implementation of the process established by the legislation. The scope of the legislation covers engineering enterprises in Queensland and engineering activities elsewhere that may have been designed in Queensland. There is currently a challenge to determine what the necessary health and safety competencies for the mining industry are and how the maintenance of these competencies will be assessed. The different approaches taken by the two assessing entities are compared and contrasted. At the legislative level, establishing an obligation to assess professional competency is simple, but at the level of the profession, it is new ground that warrants a substantial research and development input. The challenge is to develop criteria by which the quality of such system can be assessed. The comparison is made by considering such issues as equity, effectiveness, efficiency, objectiveness and transparency. These five indicators are considered in terms of how they are applied in other sectors and how they might be applied in the mining sector.

Jan 1, 2009

By J Vann

Mineral Resource and Ore Reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential pitfalls are to be avoided, however, there are two other requirements which are of equal, if not greater, importance:good communication, and common sense. Estimation of Mineral Resources and particularly of Ore Reserves is almost always a team effort, involving a number of disciplines. Good teamwork requires good communication, both between team members and between the team and other parties having an interest in the process. Breakdown in these lines of communication can have far reaching effects on the project under consideration. The need to use common sense during a Resource or Reserve estimation exercise would seem to be self-evident. It is surprising, however, how often rigid adherence to procedures and methods prevails at the expense of clear thinking, usually with adverse and sometimes fatal effects on the project under consideration. This has become increasingly true as computerised methods have assumed a central role in Resource/Reserve estimation. The critical question that estimators should ask themselves at all stages of the process is: æIs what is being done sensible given the data available, what is known of this deposit and the purpose of the exercise?Æ

Jan 1, 1999

By J Weir

Accurate sampling of slurry streams is extremely important for metallurgical accounting in mining operations, not only for measuring the ore grade from the mine, but also for measuring the recovery of mineral by the mineral processing plant. Accurate sampling is also required for intermediate streams in complex circuits for determining efficiencies of processing units within the plant. As the profitability of the minerals industry is squeezed more with time, greater emphasis is being placed on efficient use of the resource and accountability of the various sections of the mining operations. This has led to increased awareness and interest in obtaining statistically correct sampling across the operations. Accurate sampling is not only required for metallurgical accounting, but is also required for on-line analysis of the slurry streams for elemental analysis and for particle size. Sampling of slurry streams for metallurgical accounting purposes has traditionally been one of the areas of concern in mineral processing plants. In the first instance, the sampler must be designed to comply with the fundamental principles of sampling theory and must provide a representative sample of the slurry stream. In the second instance, the sampler must continue to reliably provide a representative sample, regardless of wear of the equipment or build up of solids with time and other operating issues. To-date the main type of sampler that has been used in mineral processing plants for metallurgical accounting has been the Cross-Cut sampler. These have a cutter that periodically cuts across the full slurry stream. For large flow slurry streams, these are often followed by a secondary and perhaps a tertiary sampler, to reduce the flow-rate or sample, to a manageable size. This paper discusses a new method of sampling slurry streams that has been developed by Thermo Gamma-Metrics, previously known as Amdel Instrumentation. The new samplers overcome many of the problems associated with cross-cut samplers while providing a sample which is representative of the main stream, throughout the life of the sampling system. The sampler is called the SamStat (Sampling Station) and it is now proven in many applications across many countries and mineral processing plants (PGMs, Cu/Au, Pb/Zn, etc).

Jan 1, 2002

In November 1986 the Australian Minerals and Energy Council (AMEC) endorsed an "Australian Code for Reporting Identified Coal Resources and Reserves" for use by the Federal and all State Governments. Before this endorsement there were six different coal codes in use in Australia. The code is broad in nature to accommodate the wide range of coal deposits in terms of rank, quality and geological environment, that are present in Australia. In the code, Resources refer to all of the coal in situ which may have potential for use and the various categories indicate the level of confidence of the assessment. Reserves are those Resources which are planned to be mined and for which such planning has been undertaken. Only minimum guidelines are set by the code and the onus is on the estimator to state clearly the criteria used in any Assessment.

Jan 1, 1987

Advances in technology have led to larger and deeper open pit mines and, consequently, also increased the potential economic impact associated with slope failures. If the ultimate aim of mining operations is to maximise project profit, it is surprising to see related research activities have mostly been focusing on technical areas such as slope stability modelling, but with limited studies conducted to date to assess the relationship between geotechnical uncertainties and economic risk. Given most major decisions in the mining industry nowadays are made by management staff with financial background, any design approach that would help to link slope stability analysis results with monetary values would no doubt enhance communication between geotechnical practitioners and decision makers. This paper presents a study which assesses economic impact of slope failures to assist in mine planning. The study also estimates the impact of slope failures on project value, which would enable economic risks associated with pit slope designs to be closely examined. The proposed risk assessment techniques, used by financial institutions for many years to assess portfolio risks, can assist geotechnical practitioners in quantifying risks of slope failures. Risk-adjusted concepts are also suggested to assist management in selecting a slope design with optimal risk and return ratio.

May 1, 2010

Study on New Tungsten Beneficiation Technological Flow Sheet of Shizhuyuan Polymetallic Mine

Sep 13, 2010

The ERMS Process was developed during four years of testwork by Austpac Gold NL to overcome the severe metallurgical problems of the ilmenite atWestport, in the South Island. These deposits have been known for about one hundred years. They were originally mined for gold, and only later attracted attention as a possible source of titanium minerals.   The resource is of world scale and may exceed 20 million tonnes of contained ilmenite. Similar deposits occur at Barrytown further south and together these areas would constitute an important opportunity for export-oriented mineral development, if a viable beneficiation technology were available. Further processing is essential, as the composition of the ilmenite is well below market specifications.

Jan 1, 1993

Laboratory testwork was carried out on an overall orebody composite, of 2.9 per cent Cu and 4.2 per cent Zn, prepared from drill core taken from the Currawong fine-grained, copper-zinc massive sulphide deposit near Benambra in Victoria. While 90 per cent of the copper was readily recovered in a concentrate of 20 per cent Cu, after grinding to 95 per cent passing 38 microns, zinc responded poorly to conventional flowsheet/reagent regimes. Experience elsewhere with the use of reverse cleaning, to separate pyrite from sphalerite, led to a series of tests in which better (but still modest)metallurgical results were obtained. The best result was a zinc recovery of 55 per cent in a concentrate of 50.5 per cent Zn. The major loss of zinc occurred in the reverse cleaning stage where the unit recovery of zinc was similar to pilot plant results achieved at Mount Isa Mines on similar feedstock. Diagnostic mineralogy suggested that an overall zinc recovery of 70 per cent was probably the practical upper limit, at a 50 per cent Zn grade.

Jan 1, 1999

Miners and explorers in New Zealand are expected to consult with stakeholders, keep out of core conservation areas, and operate a high standard of environmental management and rehabilitation. These requirements are not difficult to meet, but many of the industry's own actions have brought it to a low level of general public esteem in New Zealand. Reasons for this are discussed, drawing examples from the Maruia Society's experiences with the industry since the mid-1980s. The boundary between core conservation areas and other land is not easily drawn, and the Maruia Society has sought to work with the mining industry to promote legislation for net conservation benefit trade-offs. However this initiative was not successful. Today the industry, unlike most other major industry sectors in New Zealand, has no accord with the country's conservation movement.

Jan 1, 1997

The Australian mining industry faces skills shortages across a broad spectrum of disciplines and levels, as it enters another major growth phase. Critical amongst the areas of most significant shortage in the professional sphere is the discipline of geotechnical professionals. More mines, deeper mines, ageing workforces are all contributing to this chronic shortage. But the shortage is not just at the operating sites, it is across a range of employment fields including sites, head offices, consultants, researchers and educators. This paper reviews the status of a number of these fields and explores some of the issues being faced. The different roles of a site geotechnical professional and a specialist geotechnical consultant are explored, together with some of the trends in terms of how such people are operating, and the skills they are expected to have to fulfill their job requirements. The paper also considers the move towards possible mandatory statutory geotechnical positions at mine sites and some of the implications if this were to come into force. Finally, the paper considers the current provider programs for mining geotechnical education, and how additional offerings are going to be needed in order to address the current shortages and the inconsistencies in terms of job expectations for people assigned to geotechnical roles without adequate education and training.

Nov 25, 2010

By A Lim

"As Abel Mine continues to expand and increase production, the requirements of the ventilationsystem have also increased. This paper will outline the stages undertaken to increase the AbelMine ventilation system from an operating position of 110 m3/s and 500 Pa to the current operating position of 220 m3/s and 1.6 kPa and outline steps to be taken to ensure all future requirements will be able to be ventilated."

Jun 1, 2012

By Lee H. G, El-Rahaiby S. K

The literature relating to reduction of sulphides by carbon using lime as sulphur-absorbent is reviewed. A stage-wise thermodynamic model is employed to evaluate the practical feasibility of the direct reduction smelting of galena (PbS) concentrates with a carbon reductant in the presence of lime; a coke-rate of 65 kg/ton Pb is predicted by the model. The experimental data on the reduction of PbS:4CaO:4C mixtures under nitrogen were correlated by means of a finite difference numerical method and the values of the intrinsic rate constant I1 were derived. The results for the uncatalysed reduction are represented satisfactorily with log I1 = 1.247(±0.522) - 5540(±610)T-1.The catalysed PbS:4CaO:4C mixtures contained 2.5 wt% of ternary (K, Li, Na)2CO3 catalyst. For the catalysed reduction it was found that log I1 = 3.981 (±0.301) -7790(±353)T-1, where I1 (in both relations) is expressed in moles.(g.C.)-1.atm-1.s -I. The catalytic enhancement faclor was found to be quite large in the 1068 to 1262°K temperature range investigated here.

Jan 1, 1991

India is on fast economic growth. Even in the turbulent years of global crisis, it could achieve a growth of over eight per cent. In recent past, Indian Government has been contemplating a faster growth in all the sectors of economy so as to make the nation an economic power in the world.Steel is a versatile material. It has its role in most of the major industrial activities, such as infrastructure, automobiles, urbanisation, consumer durables and other. In other words, steel is a part and parcel of industrial expansion, urban and rural development. It is rightly admitted that steel acts as pillar of any development model. Volume of steel consumption is the barometer which measures economic progress and/or industrial status of any country.India and China are the two countries in Asia which have the significant impact on the global steel industry. Of course, China is much ahead of India in consumption level of steel.

Dec 6, 2010

Project Sustainability Assessment - Matching Method to Enterprise Size Sustainable development requires managing natural resources, including minerals, in a way that is conducive to long-term wealth creation and the maintenance of capital (natural, social, human, economic and physical). One aspect of the minerals sustainability discussion focuses on replacing depleted mineral capital with other forms of capital so as to ensure that the contribution of a mineral project is net positive over its life. Another, equally important, aspect focuses on selection of projects and technologies that contribute to the achievement of a variety of sustainability objectives, such as environmental protection, efficient use of resources, water and energy, worker health and safety, and the equitable distribution of risks and benefits within and across generations. Technical feasibility and relative economic performance remain necessary decision criteria for mineral investment decisions, but they are no longer sufficient. Enterprises, regardless of size, are now confronted with the challenge of comparing investment alternatives based on a new, broader set of criteria. The field of integrated sustainability assessment (ISA) emerged in response to this changed social and business environment. ISA is a structured process for examining the economic, social and environmental impacts of a project or technology. The purpose of an assessment can be broad, a strategic review of corporate behavior for example, or quite narrow, input to a specific decision process such as the selection of a piece of equipment. There are numerous methods and analytical tools available to conduct ISAs and selection of the most appropriate for a given situation will depend upon temporal focus (retrospective to prospective), decision context (strategic, tactical or operational), and phase of the assessment process (problem structuring, analysis, resolution, ex post review), among others. Selection also depends upon enterprise size and the attendant availability of financial and human resources. Large multi-national firms often undertake complex, data intensive sustainability assessments, in part because the projects they are involved in are multi-faceted, long term, and require significant financial investments. Small and medium sized enterprises are seldom able to commit the same level of resources to an ISA, and if the projects they undertake are less complicated, a time consuming and detailed assessment may be unnecessary. Regardless of enterprise size, the tangible and reputational benefits of conducting as ISA must exceed the actual monetary cost of doing so. This presentation will provide an overview of available ISA tools, categorising them in terms of their data requirements, methodology, outputs and applicability in various decisions contexts. Distinction will be drawn between situations where reasonable approximations of project impacts can be expected to provide an adequate amount of information and those for which more detailed analysis is essential. Finally, ISA strategies that have been successful and cost effective at different scales of business enterprise will be identified. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

Corrosion affects the performance of rock support and reinforcement at various underground mines, including the George Fisher Mine, where recent studies showed that this risk to mining operations is generally not well understood. Corrosion reduces the capacity and life expectancy of ground support and generally is undetected unless the traditional destructive pull out test is employed to detect defect bolts. Where it is still acknowledged that the pull out test has still an important role to play in determining critical bond lengths for static and quasi static ground support designs, it does not provide an underground operation with any reassurance regarding its bolt's integrity, which has been compromised by in situ aggressive conditions. Non-destructive rock reinforcement calibration testing on single and twin strand cable bolts, rebar bolts and friction bolts at the George Fisher Mine enabled the testing team to detect bolts with compromised integrity in one area of the mine. The non-destructive rock reinforcement integrity testing conducted uses a complex 'Stress Wave Analysis' package based on the processing of clear seismic signals imparted into the rock reinforcement element that is being tested. The seismic signals are processed by 'Fourier Transform' into various criteria which can be used to produce models of the element such as mechanical admittance, frequency spectra and velocity which are all being used in the final modelling of the rock reinforcement element under analysis. This paper highlights the enormous potential to effectively manage the geotechnical risk that corrosion presents for an underground mining operation.

Nov 25, 2010