Search Documents

By A. J. Strauss

The solubilily of lead in PbS as a funclion of lemperature has been investigated by means of Hall coej'icient (RH) measurentents OIL samples prepared by annealing and quenching Bridgman-grourz single crystals, which contain excess lead incorporated during /heir growth from the mell. For sufficiently long annealing times and sufficiently rapid quench rules, the samples obtained consist of n-lybe PbS snturated with In the semiconducting compounds PbS, PbSe, and PbTe, the point defects associated with the presence of lead in excess of the stoichio metric composition are shallow donors. The defects associated with the presence of excess nonmetal are shallow acceptors. lead at the annealing teuiperatiire, together luilh a dispersed second phase of lead microprecipitates. Due to the retrograde solubility of lead, the measured free carrier concentration (n = l/eR77) decreases with decreasing annealing tewperature (T) from- 2.4 X 10 em-3 for 1l85OK to 1.3 X 1018 cm-3 for 623°K. The dala are well-represented by the equation n =(1.08 x 102) exp[ - (0.37 ev.)/kT] cm-3 For most undoped samples of these compounds, the carrier concentration at room temperature and below is determined primarily by the stoichiometry, since the concentration of either excess lead or excess non-metal is large compared to the concentrations of intrinsic carriers and electrically active impurities. Therefore the dependence of composition in temperature and partial pressure can be investigated by means of Hall coefficient measurements, even though the deviations from stoichiometry do not exceed 0.03 at. Pct

Jan 1, 1968

Since the comprehensive review of the Persian fields presented by Sir John Cadman last year, operations have proceeded normally. No developments of especial importance fall to be recorded and it remains only to bring up to date the full information given at the beginning of 1933. Controlled production from the Masjid-i-Sulaiman and Haft Kel fields has been maintained at slightly higher rates than during 1932. The figures for the past five years are as follows: These represent crude oil and products piped to the coast but exclude products reinjected into the reservoir, a process that has been in continuous operation at Masjid-i-Sulaiman during the period under review. The systematic delimitation of the Haft Kel field has been continued during the past year and results have been sufficiently encouraging to justify the inception of a wider scheme for distribution of production. Drilling has been resumed recently in the Persian sector of the Naft Khaneh field, and preliminary survey work is in progress for the selection of a site for a refinery at Kermanshah arid the construction of a connecting pipe line. Investigations in connection with the scientific control of reservoir were dealt with in considerable detail in last year's review. This work has been steadily pursued during 1933 and certain of the investigations have been the subject of papers presented to the World Petroleum Congress held in London in July of last year.

Jan 1, 1934

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

Jan 1, 1943

Jan 1, 1943

Jan 1, 1970

By S. Frederick Ravitz

IN most applied sciences there are two distinct methods of carrying out research and development work. One of these, the theoretical, attempts to solve problems that may arise and to predict facts of practical importance by the application of the various laws of science, the other, the experimental method, attempts to each the 'same goal by obtaining data and trying out various processes in the laboratory. Since individuals frequently find themselves better adapted for one or the other type of procedure, it is natural that -two groups should 'arise, both working toward the sane objective but with somewhat different points of view, although many in each group are thoroughly competent in both fields. Metallurgy, in particular, offers an excellent opportunity for a comparison of the two methods.

Jan 1, 1935

United Engineering Trustees, Inc. GEORGE D. BARRON ARTHUR S. DWIGHT R. M. ROOSEVELT The Engineering Foundation H. C. BELLINGER E. DEGOLYER J. V. N. DORR

Jan 1, 1932

By Robert F. Calman

OUTLINE FIVE EXAMPLES OF GOLD-LINKED FINANCINGS 1. Financing the Lupin Mine • Sale of Cdn $40.0 million of 12% preferred shares and Cdn $40.0 million of Gold Purchase Warrants @ $595 per ounce. 2. Financing the Copper Range acquisition • Borrowing 100,000 ounces from a Canadian chartered bank @ US$307 for five years. 3. Financing the Round Mountain expansion • Borrowing up to US $80.0 million in dollars, convertible into gold, repayable over five years from a group of North American banks. 4. Financing the Tenneco Precious Metals Division acquisition •Sale of SFr 110.0 million of ten year 3-718% bonds with warrants to buy 132,000 ounces of gold at US $560. 5. On Forward Sales, Puts and Calls • Gold, Silver, Canadian Dollars, Swiss Francs THE FINANCIAL RULES AT ECHO BAY 1. Never bet the company 2. Equity is the primary form of capital for a gold mining company 3. On debt 4. The Yardsticks for Corporate Decisions 5. Financial Community Relationships 6. Dividend Policy No Text Available Tables Follow

Jan 1, 1990

To assist the taxpayer of the oil and gas industry in correctly and expeditiously preparing his Federal tax returns, the Bureau of Internal Revenue has prepared a "Manual for the Oil and Gas Industry Under the Revenue Act of 1918." Although the endeavor has been made to anticipate all questions that may be asked, it is recognized that such a manual is only general and cannot cover all cases that may exist. The Manual is based largely upon information gathered during the fall of the year 1918 by a corps of geologists, technologists, and engineers. The investigation was undertaken primarily to furnish a basis for arriving at valuations, and depletion and depreciation deductions in connection with oil and gas properties. All fields in the United States were canvassed. Records of production of thousands of properties were collected and tabulated. These were carefully classified and studied by the most competent and experienced men in the country and the average future production curves and tables of valuation data were produced as a result of this study. Be American! Work and Save. Buy W. S. S.

Jan 7, 1919

By Gerhard Bockstiegel

Kuczynski's formula has been derived for the case of nonspherical particles. TWO formulae of Kuczynski's type have been derived, one describing the increase in tensile strength, the other describing the progress of shrinkage of a powder compact. It has been strength,shown that the exponents of all three formulae each contain two magnitudes of different physical characters, viz, the geometrical factor a and the kinetic factor ß. The interrelationships between the three exponents are stated. SOME years ago Kuczynski1 experimentally showed that the radius, x, of the area of contact between very small spherical metal particles and a metallic block is related to the time of sintering, t, by the following equation x = constant tk [11 where k has the value 1/5 or 1/7. Assuming that the metal particles were perfect spheres and the metallic block was perfectly flat, he derived the foregoing equation from theoretical considerations of the process of material transport in metals, and he showed that exponent k is different for different mechanisms of transport, e.g., k = 1/2 for viscous flow (according to Frenkel2), k = 1/3 for evaporation and condensation, k = 1/5 for volume diffusion, and k = 1/7 for surface diffusion. From this Kuczynski concluded that the mechanism of transport was either volume diffusion or surface diffusion, depending on whether the value of k, as found in his experiments, was 1/5 or 1/7. Subsequently. Cabrera8 corrected Kuczynski's calculations with regard to surface diffusion, showing that the theoretical value of exponent k is 1/5 for both volume and surface diffusion. He supposed that the different experimental values of k were due to slight differences in the shape of the metal particles. An exponential relationship similar to the aforementioned was found by Okamura, Masuda, and Kikuta,4 Masuda and Kikuta, and Takasaki8 when studying the rate of shrinkage on powder compacts during sintering. The authors measured the shrinkage by means of the fraction w = Vp — V./Vp — V,,,, where V,, is the volume of the green compact, V, is the volume of the sintered compact, and V,,, is the volume of the compact in its densest state. This fraction, w, they found, is related to the time of sintering, t, by the equation w == constant tm. [21 Further, Bockstiegel, Masing, and Zapf7 observed that the tensile strength, s, of sintering iron powder compacts can also be related to the time of sintering, t, by an equation of the foregoing type, i.e., s = constant tn. [3] For exponent n the values 0.28 (S=2/7) and 0.35 ( 2/5) were obtained, and the authors pointed out that there might exist a simple interrelation between exponent n as found in their experiments and exponent k in Kuczynski's equation. The authors supposed that 2k = n, since the strength of adhesion between a metal sphere and a block (as in Kuczyn-ski's experiments) must approximately be proportional to their contact area, p. x2. Theoretical Considerations This paper is an attempt to correlate the fundamental experiments of Kuczynski's type with the results obtained with powder compacts as represented by Egs. 2 and 3. In particular, the paper is to show how the rate of sintering is influenced by the geometry of the sintering particles and by the type of material transport. As the geometry of particles conglomerating in a powder compact is very complex, some simplifying assumption has to be made, of course, in order to adapt the problem to mathematical treatment. In the following paragraph a suitable simplification is introduced, and Kuczynski's formula is derived for the case of nonsphcrical particles. Relation Between Area of Contact and Sintering Time—As the face of contact between two particles in a sintering powder compact is not necessarily a circle (as in the case of spheres sintering to a block), Kuczynski's formula is modified as follows: Let the perimeter of the face of contact be described by means of polar coordinates R, 4, as shown in Fig. la, so the area of contact, f, is determined by f= 1/2 . S112p[R(Æ) ]2 dÆ [4] Then, let the two particles be intersected by a plane perpendicular to area f. The intersection is shown in Fig. lb. According to the nomenclature in this figure, the distance, h, between the surfaces of the two particles is a function of T and Æ: h = h(r,Æ). For the particular case of spherical particles, as in Kuczynski's theory, this function becomes: h = constant r2. It shall be assumed here that in the close neighborhood of their

Jan 1, 1957

Jan 1, 1970

By S. Saito, P. A. Beck

The crystal structure of MoNi3 was determined by means of X-ray diffraction. This structure is isotype with that of ovgered TiCu3. The lattice parameters are: a. = 5.064A, bo = 4.224A, co = 4.448A, and zf 0.157. If the orthorhombic distortion (slight relative to the corresponding orthohexagonal unit cell) is disregarded, the structure may be described in terms of a close-packed ordered atomic layer, stacked in the sequence: abab. The structztres of ordered TiCu3 and TiAl3 are homotectic. The three types of ordered hexagonal phases, iso-structural with TiNi3, MgCd3, and VCo3, are known to occur in AB3 alloys of transition elements of the first, second, ad third long periods. It was noted1 that phases with the TiNi3 structure occur selectively in alloys of Ti-group elements with Ni-group elements. In AB3 alloys of Ti-group and V-group elements with Co-group elements the AuCu3-type structure predominates.' The vCO3 structure, which was determined very recently,' has hexagonal symmetry, but the actual atomic arrangement here, too, is rather closely related to the ordered cubic structure of AuCu3-type. However, an ordered hexagonal close-packed structure of the MgCd3-type occurs in MOCO33 and WCO3.4 Consequently, the question arises as to whether or not the crystal structure of MoNi3 is also of the MgCd3-type. Grube and winkler5 found that MoNi3 has a hexagonal close-packed structure with a = 2.54A and c/a = 1.65. They pointed out that some additional weak diffraction lines could be observed in the powder pattern, which may have been due to an ordered atomic arrangement in this phase. However, no detailed information was obtained by them and the structure was apparently not further investigated by others. The present work was, therefore, undertaken in an attempt to determine in detail the structure of MoNi3, and to investigate the possibility of ordering. EXPERIMENTAL METHODS Alloys used in the present work were arc-melted in a water-cooled copper crucible under helium atmosphere. Electrolytic nickel and molybdenum, both 99.9 pct pure, were used. Chemical analyses were not made, but the melting loss was not higher than 2 pct for any alloy. Ingots were first homogenized at 1200°C for 48hr, quenched, heavily cold worked, and then annealed at 820" or 860°C for 1 week, followed by quenching in cold water. Powder specimens for X-ray work were prepared by crushing the heat-treated solid specimens. In order to remove strains, the powders were reannealed in evacuated scaled fused silica capsules for 6 hr at the same temperature at which the corresponding solid specimens were annealed. X-ray photographs were taken with an asymmetric focussing camera, using unfiltered CrK or CuK radiation. EXPERIMENTAL RESULTS The X-ray diffraction patterns of alloys containing 20.8, 25, and 26.4 at. pct Mo, homogenized at 1200°C, showed the face-centered-cubic structure of the Ni-base a-solid solution. It was revealed, however, by micrographic examination that the 26.4 at. pct Mo alloy contained in addition very small amounts of a second phase, in accordance with the phase diagram.6 On the other hand, the 20.8 at. pct Mo alloy after annealing at 820°C gave the X-ray diffraction pattern of the ordered face-centered-tetragonal MONi4.7 In this pattern several additional weak diffraction lines were also observed, corresponding to the strongest diffraction lines of MoNi3. The alloys containing 25 and 26.4 at. pct Mo after annealing at 820" or 860°C gave X-ray diffraction patterns, as shown in Tables I and 11, corresponding to MoNi3. Each one of the reflections which could be tentatively indexed on the hexagonal close-packed cell of Grube and Winkler,5 with the exception of the basal plane reflections, was split into a doublet, as seen in Table I. Since microscopically the alloy consisted of a single phase, it seemed probable that the lattice of MoNi3 is actually slightly deformed, as compared with the tentative hexagonal unit cell. In addition to these diffraction lines, several weak lines were also present, as shown in Table 11, which could not be indexed at all on the hexagonal close-packed cell considered. Satisfactory indexing of all diffraction lines observed was found to be possible by using an orthorhombic unit cell with ao = 5.064A, ft = 4.224A, and c = 4.448A. These values, whose accuracy is estimated to approximately ± 0.008A, correspond to 95.14A3 for the volume of the unit cell, and to an X-ray density of 9.50 g per cm3. If no attention were paid to the weak reflections listed in Table II, a reduced -unit cell of half the volume (a = 2.532A, b = 4.448A, and c = 4.224A), closely related to the orthohexagonal cell, might be used. The dimensions of the orthohexagonal cell of the same volume as the reduced cell are: a = 2.562A, b = 4.437 A, and c = 4.183A. It may be seen that in the reduced cell the a axis is slightly shorter, while the b and c axes are slightly longer than those corresponding to the orthohexagonal cell of the same volume. This slight orthorhombic distortion is re-

Jan 1, 1960

By P. M. Robinson, J. S. LI. Leach

The heats of solution oj' indiurrr, tin, lend, nrzd tellurium have been calculated from the measured heat effects when mechanical mixtres of indium and telLuium tin and tellurium, and lead and tellurium were added to liquid bismuth. The results are in good agreement xith publislzed values.s for the separate sollction of each eleltzent in bismuth. The heats oj solution of cadmium and tellurium calculated from the rneasuved heat effects on adding trechanical mixtures of these elements do not ugree zc,itl the published values jbv the separate solution of each element. It is shown that at 623°K Ile interaction between cadmium and tellurium dissolved in liquid bismuth is strong enough to led lo preciPitation of solid CdTc. The heats oj- jor-mation of CdTe at 273" nd 623°K (1)-c crilculated fi-or the measured heat ejlfecls. The calcnlaled az'erage deviation from the Kopp-l\'ez?,zunrz rule fov solid CdTe is less than 0.06 cat per g-atom- C over this lertzperalure range. Tlze importance 0.f these oDserl.ations to the determination of heals of formation hy metal solution calorimetry is considered. LIQUID metal solution calorimetry is a convenient method for determining the heats of formation of solid compounds. In this technique the heat of formation is the difference between the measured heat effects on dissolution of the compounds and of mechanical mixtures of the components in the liquid metal.' The heat of solution of the mechanical mixture may be calculated from the measured heat effect. At infinite dilution of the solutes, this heat of solution is equal to the sum of the heats of solution of the separate components. If the heat of solution of one of the components is known, the value for the other can be derived; if both are known, they may be used to check the accuracy of the calorimetric technique. The heats of formation of the tellurides of cadmium, indium, tin, and lead have recently been measured by metal solution alorimetr. The heats of solution of indium, tin, lead, and tellurium at infinite dilution in liquid bismuth at 623"K, calculated from the measured heat effects on solution of the mechanical mixtures, are in good agreement with the published values. The heats of solution of cadmium and of tellurium calculated from the measured heat effect on solution in bismuth at 623'K of mechanical mixtures of cadmium and tellurium, however, do not agree with values estimated from the literature. 1) EXPERIMENTAL PROCEDURE AND RESULTS The Heats of Solution of Indium, Tin, Lead, and Tellurium in Bismuth. The heat effects were measured when mechanical mixtures corresponding to the compounds In,Te, InTe, In2Te3, In2Te5, SnTe, and PbTe were dissolved in bismuth. The calorimetric procedure and the method of calculation have been described elsewhere.' The heats of solution of the mechanical mixtures were obtained by subtracting the change in heat content per gram-atom of the sample between the addition temperature (273°K) and the bath temperature (623"K), (H623°K - H273°K)S, from the measured heat effects. The calorimeter was calibrated with pure bismuth. The reported values of the measured heat effects are based on (HGoK - ^273oK)Bi = 4.96 kcal per g-atom.3 The measured heat effects are found to be linear functions of the solute concentrations of the bath in the dilute solution range. The values, extrapolated to infinite dilution, are listed in Table I, together with the heats of solution of the mechanical mixtures calculated using the published values of (H 623°K - H273°k)s for indium, tin, lead,3 and tellrium. All the error limits quoted in this work represent the spread of values obtained. The heats of solution in liquid bismuth at 623°K of mechanical mixtures of indium and tellurium in four different proportions were determined. Values of the heats of solution of the two components were then calculated from the resulting four simultaneous equations: The heats of solution at infinite dilution of tin and lead in liquid bismuth at 623°K were calculated from the heats of solution of the mechanical mixtures of tin and tellurium and of lead and tellurium using the heat of solution of tellurium calculated above. These values of the heats of solution are listed in Table I1 together with some published values for comparison.

Jan 1, 1967

By AIME AIME

THE following paragraphs, constituting the concluding portion of the Annual Report of the Council for 1903, have been withheld from publication until now, in order to make them as accurate and complete as possible. They will be published in Volume XXXV. of the Transactions in their proper place at the end of the said Annual Report. Franklin Ballou was born in Pittsburg, Pa., May 29, 1845. He was the son of an old resident, Arthur Ballou, a manufacturer and wholesale dealer in vinegar. In early youth Franklin attended the Western University of Pittsburg, but left school at the age of 16 to become book-keeper for his father, upon whose retirement from business, in 1868, he associated himself with Walter C. Childs, of Pittsburg, in the manufac¬ture of furnace-grates and asbestos-cement for blast-furnaces. This firm was known as W. C. Childs & Co., and did a success¬ful business for several years. In 1869 Mr. Ballou married Miss May S. Wilson, daughter of Judge Wilson, of Lewistown, Pa. In 1876 he spent several months traveling in the West and studying the mining industry, which greatly interested him. In consequence of this journey, he wound up his business in Pittsburg and removed in 1877 to Georgetown, Colo., where for several years he conducted a sampling-works, and built up an extensive business as an agent for the sale of ores, besides engaging to some extent in mining enterprises. , It is said that he controlled at one time about one-eighth of the output of the Leadville mines. In the early 80's, he became Vice-President and General Manager of the Bimetallic Smelter at Leadville, of which Mr. David H. Moflat was the principal owner. This was practically the first successful demonstration of pyritic smelting in Colorado. Upon the sale of the works in 1897 to the American Smelting and Refining Co., Mr. Ballou retired

Jan 1, 1905