Search Documents

By R. E. Allen

ONE of the most unusual oil field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fe Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from

Jan 1, 1933

By H. L. Talbot, A. J. Hall, R. S. Young

A METHOD for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect it visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional. period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators were responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control purposes. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or similar elements has come to the authors' notice. EXPERIMENTAL PROCEDURE There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is, to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; A1203, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents were used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1946

By K. J. Reid, H. A. Lex, I. Iwasaki, K. A. Smith

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides from Duluth gabbro were investigated. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously ground pulps. With the ball-mill ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1984

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By Otto Henry

THE purpose of this investigation was to determine the equilibrium diagram of the lithium-magnesium pair as a first step in studying the possible usefulness of these alloys as ultra-light structural materials. REVIEW OF THE LITERATURE The behavior of lithium towards magnesium was first investigated by Masing and Tammann.(I)? In order to prevent oxidation the alloys were made in iron tubes under an atmosphere of hydrogen; temperatures were measured with a glass-protected thermocouple. These investigators found that lithium and magnesium form two series of solid solutions separated by a miscibility gap between 85 and 95 per cent magnesium; that the alloys with 81 and 95 per cent magnesium showed a homogeneous structure under microscopic examination, while the alloy with 89 per cent magnesium contained two distinguishable crystallites; that the curve indicating the beginning of crystallization rises from the melting point of lithium to that of magnesium; and that no compounds of lithium and magnesium are formed. The equilibrium diagram was not plotted because no definite data were obtained for determining the solidus and the posi-tion of the miscibility gap in the solid state. The difficulties encountered in this investigation were: (1) that it was necessary to heat them as high as the melting point of magnesium in order to obtain homogeneous melts; at such temperatures the alloys attacked the glass protecting the thermo-couple; and (2) that at temperatures above 400° C. the lithium united

Jan 1, 1934

Jan 1, 1941

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Apr. 10, 1916; to May 10, 1916: Philip P. Baily, New York, N. Y. George W. Otterson Seattle, Wash. John M. Brooks, Jr., Knoxville, Tenn. C. Q. Payne, New York, N. Y. C. A. Burdick, New York, N. Y. Charles F. Potter, Los Angeles, Cal. W. N. Crafts, Oberlin, Ohio. Albert E. Rhoads, Harrisburg, Pa. Andrew B. Crichton, Johnstown, Pa. M. F. Sayre, Schenectady, N. Y. 0. P. Hood, Pittsburgh, Pa. H. V. Smythe, Northpines, Ont., Canada. W. McA. Johnson, Tulsa Okla. W. 0. Snelling, Long Island City, N. Y. G. H. Morgan, New York, N. Y. W. H. Staver, Ophir, Colo. E. G. Norton, Chicago Ill., A. W. Tucker, Salisbury, N. C. M. L. O'Neale, Coal City, Ala. Andrew Weisenburg, Philadelphia, Pa. Arthur H. Brown has resigned his position with the Dome Lake Mining & Milling Co., South Porcupine, Ont., Canada. Robert Sterling has resigned his position as chief engineer of the Goldfield Consolidated Mines Co., Goldfield, Nev., to accept the position of assistant manager of the vanadium mines of the Primos Chemical Co., Vanadium, Colo.

Jan 6, 1916

Jan 1, 1934

THE Boston meeting, August 29-31, was in many ways one of the pleasantest the Institute has enjoyed in years. Much hard work had been done by the committee, and with excellent results. The program had been purposely restricted with the idea that a smaller, more homogeneous audience formed the best basis for a regional meeting, and the event fully justified the plan. The one hundred and sixty-three members and guests attending were dominantly interested in geophysical methods or their application, and, despite the highly technical character of the papers and the unusual heat, attendance and interest in the technical sessions were well sustained. The exhibition of geophysical instruments and aerial maps added greatly to the meeting.

Jan 1, 1928

By Edgar M. Dunn

Part I. Determination oF Gases in Smelter Flues. General considerations. Regular methods for carbon monoxide, oxygen, nitrogen, moisture. Sulphur oxides-—Methods of Lunge and Hempel tried, and either modified or discarded, with reasons therefor. Gravimetric method developed at Anaconda. Description of apparatus used. Brief notes on Richter and Hawley methods for the direct cietermination of sulphur trioxide. Carbon dioxide, with complete notes on same. Arsenic trioxide. Table of percentages of flue gas constituents found at a Western smelter. Some final notations as to the value of flue gas analysis, in connection with an intelligent log of furnace operations. Part II. Notes on the Determination oF Dust Losses at the Washoe Reduction Works, Anaconda, Mont. Discussion of problem, with description of flue system. Various places and methods for determinations of velocity. Instruments used. Procedure in making determinations for velocity. Soundings of cross-section for depths of dust. Calculation of velocities and areas. Daily volume of gas, and plant operations during tests. Place for dust determinations. Apparatus and methods of 'sampling. Results obtained, with table of daily amount of dust losses. Analysis of dusts for values, from various sampling stations. Complete analysis of composite sample of stack emanation. Last analysis totaled to show form in which present. Discussion of recovery as a commercial proposition. References on Pitot tube and calculations.

Jan 1, 1914

By AIME AIME

The 102d meeting of the Institute was held at the Institute headquarters in the Engineering Societies Building, New York, N. Y., on Feb. 19, 20 and 21, 1912. A Bureau of Information, in charge. of Mr. George Buckman, was maintained during the meeting. The proceedings opened with an informal social meeting on Monday evening, Feb. 19, in Assembly-Room No. 1, on the

Mar 1, 1912

By Hans Lundberg

AFTER the war years, great activity has been shown in geophysical exploration for ore. The appreciation by mining and government geologists of geophysical techniques and results is largely responsible for the popularity of these methods. In Canada, plans are being made to study, by geophysical methods, the structure of a portion of the Pre-Cambrian shield in the hope that such studies will not only give a clearer picture of the geology, but will be of direct aid to the mining companies when selecting areas for detailed prospecting. Although geophysics thus has become more popular, some engineers are still reluctant to employ the methods to their full extent. Allotted funds are often rather low, so that the least expensive

Jan 1, 1947

By W. F. Wheeler

A discussion of the paper of W. F. Wheeler, presented at the Toronto Meeting, July, 1907 (Trans., xxxviii., 621 to 632). A. BEMENT, Chicago, Ill. (communication to the Secretary*):¬Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible,", not-withstanding that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combustion-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term ." combustible" was an advance to be credited to the engineer .rather than to the chemist, because the latter, not having to do with the interpretation of analysis in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression " pure coal," which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Sep 1, 1908

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world's resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

By H. Herbert Hughes

ECONOMISTS have predicted that the present business depression ultimately may pay big dividends to industry through the cumulative savings resulting from technical improvements and merchandising advances that might never have been developed under normal conditions. Waste prevention is a sound medicine for economic ills. In theory, this prescription may be applied not' only to raw materials, but also to labor, fuel, over- head, and other phases of production. Actually, how- ever, regardless of the efficiency of operating practices, waste is inevitable in the production of many commodities. The problem then becomes one of profitable utilization of waste rather than prevention.

Jan 1, 1932

By S. W. Nabbs, W. D. Bachman, A. W. Last

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from. Kennecott Copper Corp.'s Chino mine. The grindability of the various samples was found to vary over an extremely wide range, even among samples taken from diflerent locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale nonhomogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully. In the past 15 years, comminution by primary autogenous grinding has been investigated and applied economically in the minerals industry, particularly in iron-ore processing. Successful application of primary grinding is described by A. A. Dor,l.' P. B. Dettmer,334 R. R. Turner, and W. F. McDermott." other authors describing the advantages of primary grinding include H. Hardinge,' R. T. Hukki,' D. S. Coyle" and F. C. Bond,"," to mention only a few. For the past several years, Kennecott Copper Corp.'s Metal Mining Div. Research Center has been investigating primary grinding of disseminated copper ores. Both fully autogenous and semi-autogenous grinding has been explored. Ores from three of Kennecott's western operating properties and from several development properties have been tested. Host rocks include diabase, schist, silicated and argillaceous limestones, shale, granite porphyry, quartzite, and granodiorite. The object of this paper is to supplement the general knowledge in the field of primary grinding by presenting information gained from the studies with the various disseminated copper ores. Data are presented which show that carefully considered test programs are required to determine the practicality of applying autogenous grinding to a specific mining-beneficiation operation. Particularly this is so if more than one rock type occurs within an ore body or if there are wide variations in the degree of rock alteration within a deposit. Extensive sampling and subsequent testing of the ores within a mine are required if serious pitfalls are to be avoided and good engineering data acquired. We hope that this presentation will stimulate studies to increase the understanding of the fracturing process applicable to large pieces of rock, a factor which is important in autogenous grinding. Test Facilities and Procedures Both pilot-scale and full-scale test facilities were used to investigate primary grinding characteristics of the disseminated copper ores. A 6-ft Hardinge Cascade mill, a 24-ft Hardinge Cascade mill, and a 5-ft Aerofall mill were used in the studies. The Cascade mills were operated wet, while the Aerofall mill was operated both wet and dry. The Cascade mills were operated both for fully autogenous and for semi-autogenous grinding; the Aerofall mill was operated only semi-autogenously. Fully autogenous grinding, as the term is used in this presentation, is defined as the direct grinding of coarsely crushed rock by the action of the rock mass. Semi-autogenous grinding is defined as the grinding of coarsely crushed rock with the rock mass supplemented by a steel ball charge. Most of the test work was done using the 6-ft Cascade mill, operated under fully autogenous grinding conditions. Only limited testing was conducted with the 5-ft Aerofall mill and only one ore was tested using the 24-ft Cascade mill. This presentation is concerned, therefore, primarily with fully autogenous, pilot-scale grinding in the Cascade mill. Fig. 1 presents a diagram of the test facilities used with the 6-ft Cascade mill. Principal test equipment consists of a 6-ft Cascade mill, an 18-in. spiral classifier, an elevator, a 2 x 9-ft belt feeder, a conventional integrating kilowatt-hour meter, and a recording wattmeter. In testing, feed charges, adjusted as to weight, were deposited as evenly as possible on the belt feeder every 15 min. The weight of each charge was adjusted to maintain a mill charge of 27 to 30% of mill volume. The classifier was adjusted to obtain the desired size-consist of the final product, generally at 20% + 100 mesh. After equilibrium was established in the circuit, the feed, mill discharge, classifier sand, and classifier overflow were sampled and their size distributions determined. During the sampling periods, the power drawn by the mill was measured to determine the energy consumed in the reduction of the size consist of the ore solids. Fully Autogenous Pilot Grinding Tests on Various Kennecott Ores Typical test results obtained in the 6-ft Cascade mill with samples from Kennecott's Ray Mines Div., Chino Mines Div., Utah Copper Div., and a development property designated as Mine A are presented in Table 1. As shown, the ores that were ground most easily in the pilot-scale mill were composite mine samples obtained

Jan 1, 1971

By Will Clark

HE who enters a mining claim within an Indian reservation of the United States of America acquires no rights thereby, because of the fact that the lands within such Indian reservation are not a part of the public domain, and cannot be located or acquired as mineral land. However, where such an entry is authorized as to a particular reservation by an Act of Congress, such claims as may be entered under such authorization are thereby segregated from the reservation, and the Indian title is extinguished. Under the Choctaw Constitution, any citizen of that nation, in other words any Choctaw Indian, who discovered a coal mine, acquired an exclusive right to all coal within a radius of 1 mile. The laws of the Chickasaw nation provided for the formation of corporations to develop coal and other mines, with authority to contract with others to develop and work the mines. Under these laws, leases were made; but Congress subsequently abrogated all existing leases, prohibited all persons from receiving royalties from such mines, and provided that all coal within the nation should remain the common property of the tribes. Such leases are now expressly prohibited by an Act of Congress (32 United States Statutes at Large, 655). All leases of mineral lands upon Indian reservations must now be made under regulations promulgated by the Secretary of the Interior, and the royalties must be paid into the United States Treasury for the benefit of the tribes. In Canada the Indians have no rights to the royal mines and minerals, and the government can make no stipulation with the Indians which would affect the rights of the Province in which the lands are situated. Therefore, while it is true that under our present law no rights can be acquired to a mining claim within an Indian reservation, it seems to be fully within the authority of Congress to make laws, giving such rights to mineral locators as it may deem necessary or expedient.

Jan 6, 1914

By Clyde E. Williams

THIS review of the progress made in iron and steel metallurgy during the past year is confined to developments in this country. It attempts to give examples to illustrate progress made rather than to appraise results. As a result of the gradually diminishing supply of rich iron ores and of predictions made as to the probable life of the iron-ore reserves of the Lake Superior District, attention of iron and steel executives was directed to the question of beneficiation of iron ores. Laboratory and plant-scale experimental work was conducted on the wash ores .of Minnesota and an investigation, was, begun on the Old Range low-grade ores.

Jan 1, 1931

By I. Cadoff, J. P. Nielsen

The Ti-C phase diagram exhibits a peritectic point at 1750°C and 0.8 pct C, and a peritectoid point at 920°C and 0.48 pct C. The maximum solubility of carbon in a titanium is 0.48 pct. The 6 region containing the Tic compound (20 pct C) extends to 11 pct C at the peritectic temperature. THE interest in the Ti-C alloy system stems from the fact that carbon occurs as an impurity in titanium alloys when graphite electrodes or graphite crucibles are used in their melting. Since titanium-base alloys are still in the development stage, some virtue may be found in carbon addition to titanium. The Tic compound is currently emerging as an important powder metallurgy base constituent similar to the WC compound. Ehrlich' identified the phases and structures present in the Ti-C system. The peritectoid region of the phase diagram was investigated by Jaffee et al." A preliminary diagram based on theoretical considerations was proposed at the outset of this research." The Tic compound has been investigated extensively and has been reported on in a large number of papers. Experimental Procedure Arc-melted alloys of 24 compositions in the range 0 to 20 wt pct C were investigated using metallography, X-ray diffraction, and, for the liquidus and solidus regions, incipient and complete melting. All alloys were prepared from iodide titanium (New Jersey Zinc Co., 99.95 pct Ti minimum) and spectroscopic grade carbon (National Carbon Co.). To prevent carbon spattering during arc melting the carbon was encapsulated in titanium. For alloys containing less than 1 pct C the powder was inserted into a capsule formed by drilling a hole in the as-received rod. For higher compositions, capsules were formed from titanium sheet. Arc Melting: The charges were melted in the copper-hearth cold electrode furnace shown in Fig. 1. This furnace is similar in principle to the all-metal unit adapted for titanium melting at Battelle Memorial Institute.' The transparent pyrex walls giving unlimited visibility during operation and the multiple-

Jan 1, 1954