Search Documents

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By FRED T. WILLIANS

INTRODUCTION. THE Park City mining-district is distinctively a camp of few properties, 5,000 acres, or one-third of the entire district, being under the management of but three companies. As a rule, the ore-bodies lie deep, with no outcrop, except where erosion has formed the deeper canyons and gulches. Ontario canyon exposed the famous Ontario ledge, and Woodside gulch showed the first ore of the Silver King Coalition mine. The Quincy ore-bodies were first brought to light in upper Empire canyon, and Thaynes canyon was instrumental in aiding the prospector during the early days of the camp. There are 22 shafts which have reached a depth of at least 500 ft., ten a depth of 1,000 ft., five a depth of 1,300 ft., and two a depth of 2,000 ft. The amount of lateral development has been proportionally extensive, including six long tunnels, four of which are in 3 miles, with a fifth now being driven. The Ontario lower drain-tunnel is now more than 4 miles long. The formations are sedimentary, dipping about 30° NW. and N., and traversed by many fissures, dikes, and faults. The principal ore-bodies are found associated either with the contact of the basal Ontario quartzite and the overlying limes, or on a quartzite stratum within the limes, or in the fissures, or along some of the porphyry dikes. The district covers the intersection of the Uintah and Wasatch ranges, which explains the existence of large folds and faults, and fissures of great length, width, and depth. In a general way, the geology of the district consists of a basal quartzite dome, which has been exposed by erosion at the Ontario property. The Ontario fissure lies entirely within this formation. Flanking this dome on the west, north, and east lie

Jun 1, 1911

By ROBERT H. BOOTH

THE happy intra-plant relationships of the Bridgeport Brass Co. are largely attributable to the interest of the management in this important business factor. In furtherance of this development Carl F. Dietz, President of the Company and a member of the Institute, has contributed the novel plan for the objective presentation of business economics, described herein. All of the officers of the corporation are active in its management and they together with many other workers filling both executive and subordinate positions have a substantial financial interest in the enterprise. The viewpoint of this organization is fairly reflected by the following quotation from Roosevelt's "The Foes of Our Own Household."

Jan 1, 1924

By H. W. Camp

ALTHOUGH the situation in the oil industry during the past year has. not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new products and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the anti-knock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gaso-line is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and com-petitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude, and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline' on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called "re-forming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature ,or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By Carl Scholz

DURING November And December, 1907, Four Serious Mine-explosions Occurred In The Appalachian Coal-Field, Which Resulted In The Loss Of Nearly A Thousand Lives And Caused An Enormous . Damage To Property. These Accidents Attracted More Than The Usual Attention; Coal-Trade And Engineering Papers Contained Many Comments And Suggestions On The Cause And Prevention Of Accidents; The Daily Press In Many Instances Condemned The Coal-Operators And Charged These Accidents To Their Negligence, Or Their Anxiety To Make Money Without Adopting Precautionary Measures. Immediately After Each Accident The Respective State ..Authorities Ordered Close Investigations To Be Made, With The View Of Establishing The Cause And Suggesting Remedies To Prevent Recurrence. Representatives Of The Technologic Branch Of The U. S. Geological Survey, To Whom The Investigation Of Mine-Accidents Had Recently Been Delegated By The Secretary Of The Interior,. Visited The Mines And Co-Operated With The Local Authorities In Their Determinations. It May Be Safe To Say Here That An Investigation Of A Mine After An Explosion Has Occurred Discloses But Little, Because. The Causes Have Been Removed And Conditions Have Been Entirely Changed. On Jan. 8, 1905, The Coal-Operators Of West Virginia Organized An Association At Washington For The Purpose Of Making Extensive Investigations, And Sufficient Funds Were Pledged To Carry Out This Work. At This Organization Meeting, The Representatives Of The Geological Survey Present Had No Suggestions To Offer As To The Cause Of These Accidents. An Examination Of The Various Reports Concerning These Accidents Indicates That The Explosions Were Caused By The Ignition Of Gas Or Dust; They Show The Point Of Origin And The Direction In Which The Force Was Expended, And Give A Detailed Description Of The Damage Done. Very Little Has Been Said As To What

Jan 7, 1908

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3

Jan 1, 1923

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By Hermsdorf, Richard P. E.

AMONG the newer lead smelting and refining plants of the country is that of the United States Metals Refining Co., at Carteret, N. J. Not only is the technical practice here modern and efficient, but exceptional care is taken to assure healthful operating conditions for the employees. One large building houses the entire department, which includes, as its chief units, one reverberatory smelting furnace, one blast furnace, two softening furnaces, one utility reverberatory furnace, two Faber du Faur retorts, five 120-ton kettles, three 60-ton antimouial lead kettles, and one 5-ton kettle for experimental purposes. There is a 10-ton overhead crane in the kettle aisle, which is also used for shipping lead. Other auxiliary equipment is referred to in the outline of operations. A general plan of the plant is shown in Fig. 2, and a general view in Fig. 1. Primary smelting operations are conducted in a 30 by 11-ft. reverberatory furnace with bottom, roof, and upper walls of clay brick, magnesite

Jan 1, 1934

By Vincent P. Gi. ccnella

GOLD was discovered in Gold Canyon on May 15, 1849. Following this discovery placer miners worked the gravels in the canyon for-ten years, finally discovering the outcrop of the Comstock lode at Gold Hill in May, 1859, and in Ophir ravine on June 12 of the same year. Before long large quantities of gold and silver, were taken from the lode and one of the West's most spectacular mining booms drew thousands of fortune seekers to Nevada. After a long period of production activity waned and in late years little mining was done. The recent reopening of the old mines and the discovery of ore in other parts of the vein, and in other veins of the district, has led to a revival of interest in the Comstock. Virginia City, Gold Hill, and Silver City, situated along the great vein system, are enjoying a period of prosperity and a large influx of people.

Jan 1, 1934

By F. Lynwood Garrison

Except in the old Catalan forge, or its modifications, attempts to make iron and steel directly from ore in a practical and economical manner have failed so frequently and completely that such schemes are looked upon with justifiable distrust. Without exception, all have failed from one cause or another, although in some instances every indication of a practical success was manifest in the beginning. It is, therefore, necessary to carefully examine and consider every detail affecting the process, or more properly, furnace, under consideration. This I have done to the best of my ability during a long visit to Russia last summer, and after satisfactorily observing the practical success of the furnace in the iron works of Count Stroganoff at Dobriansky in the Government of Perm, I decided to investigate as completely as possible the history of similar furnaces in Finland and Russia. These data, sifted and verified with the greatest possible care, form the substance of the present paper.* An illustration on page 321 of Percy's Iron and Steel shows the old type of Osmundssmide or harkugnar, which has been in use in Northern Europe since pagan times. Fig. 1 shows a furnace of this kind. It should, perhaps, more properly be called a high-bloomary furnace or forge, the Swedish word hark meaning bloom or loupe. It was with this type of furnace that Mr. Husgafvel began his experiments at Porsaskoski in 1875. Attempts to obtain better results with larger furnaces of this type were failures, as every bloom or loupe obtained necessitated blowing out the furnace with a consequent large waste of fuel. A larger furnace of course increased this waste with no corresponding advantage. A movable hearth of threeeighth inch iron, lined with a mixture of clay, quartz and lime, was next tried, but in consequence of the frequent repairs of this lining,

Jan 1, 1888

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By Arthur M. Miller

FROM the time of its establishment in 1933, the Tennessee Valley Authority has been active in the field of phosphates. Under the T.V.A. Act it has a broad Congressional mandate to guide a unified development of the resources of the region for the long-range benefit of the people. As one phase of this function, it is directed to co-operate with farmers in the experimental large-scale use of improved fertilizers and development of better fertilizer practices. Following careful study, it was concluded that the objectives of this phase could best be attained by soil rebuilding through the use of phosphatic fertilizer and lime in an improved farm management sys- tem. This activity was launched through a program of test and demonstration on farms and simultaneous technical investigations to develop new and improved phosphatic fertilizers. Phosphorus has since become a keystone of the Authority's resource development and conservation program. Human effort is being conserved by phosphate utilization on the farm, and mineral conservation has been promoted by technical developments in phosphate mining and manufacturing operations.

Jan 1, 1944

CARL A. WENDELL, New York, N. Y. (written discussion*) .-I have never seen in print anything that even remotely has approached this article in clearness and important conclusions in conjunction with work done on the sink-and-float test. I have had many hundreds of these tests made and on different specific gravity solutions and the resultant product analyzed, but I have never grasped nor been able to show what this article sets forth. This article brings out one factor very clearly to my mind; what is to take the place of the solutions of different specific gravities used to obtain the laboratory results, when it comes to washing on a large scale, since water has one constant weight only? The answer is, sizing of coal. And as we know the importance of size versus specific gravity of the material to be washed, perhaps defined (practical) lines can ultimately be gotten up so that the sizing, if any, may be determined at the same time as the laboratory work on the coal is being done. G. R. DELAMATER, ? Steelton, Pa. (written discussion?).-The authors' deductions are well founded and although they disclaim any wide experience in commercial coal washing, practically all of the data presented are applicable to coals of all parts of this country. The paper clearly sets forth the great necessity of careful preliminary investiga-tion of each contemplated washery undertaking and contains the follow-ing very true statements. "It is not safe to assume that any coal which can he successfully washed on coarse coal jigs can be cleaned more com-pletely by washing at a finer size on tables," and "The effect of finer crushing upon the completeness with which impurities may be separated from coal depends upon two opposing tendencies. First, that the more finely a raw coal is crushed, the more completely will the particles of impurities be detached from the particles of clean coal. Second, the finer a coal is crushed the more difficult it becomes to separate the pieces of clean refuse from the pieces of clean coal."

Jan 12, 1919

By Howard Smith

AT the meeting of this Institute in February 1933, I presented a paper on potash development in southeastern New Mexico1, which contained a brief review of the Geological Survey's 20-year search for commercial sources of soluble potash minerals and of the events, that led to the discovery, exploration, and first development of the deposits in that state. As a more comprehensive review of the subject was published in December2, the present paper is intended only to discuss recent developments in the domestic potash industry, particularly in New Mexico. A summary of the findings of potash in the Permian Basin, by. G: R. Mansfield and W. B. Lang, geologists of the United States Geological Survey, is now in process of publication by the University of Texas and will be omitted from this paper. In New Mexico prospecting for potassium salts during the past two years has increased materially the known area .of commercial deposits; development has resulted in an increase from one to three in the number of shafts and the starting of a fourth; an increase of annual productive capacity to 1,000,000 tons of crude salts, or 250,000 tons of K20; and an increase in annual refining capacity to 140,000 tons of muriate of 62.5 per cent grade. Construction has been completed to increase still further the production of high-grade salts. In California the American Potash & Chemical Co., operating on Searles Lake brines, has increased its plant capacity from about 100,000 tons to 180,000 tons of muriate a year and is now producing soda ash and salt cake in addition to potash and borax. Potash production from cement-plant and industrial-alcohol wastes remains unimportant.

Jan 1, 1935

By D. B. RUSHJIORE

(New York -Meeting, February, 1912.) TORCHES were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a clog in a, basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and clown the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-dam p would produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, lie would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jul 1, 1912

By A. Adiassevich

PETROLEUM has been found in Russia in various localities from north to south, as may be seen from the list given below: (a) In the basin of the Petchora river, Northern Russia. (b) In the basin of the Volga river, in the governments of Samara and Saratoff. (c) In the government of Astrakhan and in the Uralsk territory, close to the northern and eastern coast of the Caspian sea. (d) At Grozny in Northeastern Caucasus. (e) In the Daghestan territory, Eastern Caucasus, on the Caspian sea. (f) On the Apsheron peninsula (Baku and other districts) close to the Caspian sea shore. (g) On the island of Tcheleken in the Caspian sea, also on the island of Sviatoi. (h) In the Transcaspian territory on the Neftianaia Gora (Oil hill) and on the surrounding hills. (i) In the Ferghana valley in Russian Central Asia. (j) On the Kertch and Taman peninsulas on the Black sea. (k) In Siberia it has been discovered in the Transbaikal territory and on the island of Sakhalin. In the above-mentioned districts petroleum has been found to exist under different geological conditions and to vary in its chemical and physical properties. At the present time petroleum is produced in Russia at Baku, Grozny, on the island of Tcheleken, in the Ferghana district, and in the Uralsk territory. The yearly production in 1912 throughout the Russian Empire amounted to 69,400,000 barrels, of which the Baku fields were responsible for 52,000,000 barrels. This shows that the Baku fields on the Apsheron peninsula are the chief oil-producing centers in Russia, being at the same time the oldest of all our oil fields.. In this paper I shall discuss the Baku fields only, leaving all the others until a later date.

Jan 5, 1914

By P. H. Royster

SOMETHING of a mystery has attached itself to the production of ferromanganese in the blast furnace. This alloy has been produced on the Continent almost continuously since 1876 and in very considerable tonnages, but little definite information concerning the practice is to he found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country prior to 1904, bit one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public. In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many, as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations. Realizing the advantages both to the country and to the industry from a pooling of operating data and experiences, the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Although the results of this investigation have already been reported to the companies cooperating, they may he of permanent metallurgical interest, so this paper attempts to give, briefly, the more important points brought out in the investigations. OPERATING DATA IN FERROMANGANESE PRACTICE Operating data were collected by the Bureau from 11 ferromanganese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P. The dimensions, of seven of the furnaces are given in Table 1. The companies from whom this infor-

Jan 2, 1919

By Howard J. Smith

At the meeting of this Institute in February 1933,I presented a paper on potash development in southeastern New Mexico1, which contained a brief review of the Geological Survey's 20-year search for commercial sources of soluble potash minerals and of the events that led to the discovery, exploration, and first development of the deposits in that state. AS a more comprehensive review of the subject was published in December2, the present paper is intended only to discuss recent developments in the domestic potash industry, particularly in New Mexico. A summary of the findings of potash in the Permian Basin, by G. R. Mansfield and W. B. Lang, geologists of the United States Geological Survey, is now in process of publication by the University of Texas and will be omitted from this paper. In New Mexico prospecting for potassium salts during the past two years has increased materially the known area of commercial deposits; development has resulted in an increase from one to three in the number of shafts and the starting of a fourth; an increase of annual productive capacity to 1,000,000 tons of crude salts, or 250,000 tons of K2O; and an increase in annual refining capacity to 140,000 tons of muriate of 62.5 per cent grade. Construction has been completed to increase still further the production of high-grade salts. In California the American Potash & Chemical Co., operating on Searles Lake brines, has increased its plant capacity from about 100,000 tons to 180,000 tons of muriate a year and is now producing soda ash and salt cake in addition to potash and borax. Potash production from cement-plant and industrial-alcohol wastes remains unimportant.

Jan 1, 1938

By Howard J. Smith

At the meeting of this Institute in February 1933,I presented a paper on potash development in southeastern New Mexico1, which contained a brief review of the Geological Survey's 20-year search for commercial sources of soluble potash minerals and of the events that led to the discovery, exploration, and first development of the deposits in that state. AS a more comprehensive review of the subject was published in December2, the present paper is intended only to discuss recent developments in the domestic potash industry, particularly in New Mexico. A summary of the findings of potash in the Permian Basin, by G. R. Mansfield and W. B. Lang, geologists of the United States Geological Survey, is now in process of publication by the University of Texas and will be omitted from this paper. In New Mexico prospecting for potassium salts during the past two years has increased materially the known area of commercial deposits; development has resulted in an increase from one to three in the number of shafts and the starting of a fourth; an increase of annual productive capacity to 1,000,000 tons of crude salts, or 250,000 tons of K2O; and an increase in annual refining capacity to 140,000 tons of muriate of 62.5 per cent grade. Construction has been completed to increase still further the production of high-grade salts. In California the American Potash & Chemical Co., operating on Searles Lake brines, has increased its plant capacity from about 100,000 tons to 180,000 tons of muriate a year and is now producing soda ash and salt cake in addition to potash and borax. Potash production from cement-plant and industrial-alcohol wastes remains unimportant.

Jan 1, 1938

By Harry H. Power

WORK of the Committee on Education of the Petroleum Division has been under way for approximately-one year. Although some progress has been made, further activities of the Committee are necessary in order to discuss mutual problems more thoroughly by a unified group interested primarily in this field of specialization.

Jan 1, 1944