Search Documents

By A. L. Engel

STRICTLY speaking, ore-dressing does not commence until after the ore is in the mill bins, but where complex ores are treated and their minerals separated to make the best commercial concentrate with the lowest economical tailing, ore-dressing problems begin and often center in the mine itself. This does not refer to the grade of the ore, but rather to the frequent condition in which metallurgical results radically different from customary are obtained because of changes in the character of the ore treated. Different varieties of ore can usually be identified as coming from well-defined depths or zones in the mine, or from known sections of the orebody. Varying degrees of alteration of the ore, inclusions of harmful gangue material, or variations in the quantities of component metallic minerals are often causes of temporarily bad metallurgical results in otherwise successfully operated plants, especially those employing differential flotation to. recover several valuable minerals contained in the ore.

Jan 1, 1931

By C. W. Volek, J. E. Chappelear

The injection of a hot liquid into initially cool porous media, saturated with the same liquid and surrounded by two impermeable but heat conducting media (cap and base rock), has been studied both experimentally and theoretically. The temperature dependence of the viscosity was included in the theoretical model, but it was assumed that the specilic heats and densities of the various materials were independent of the temperature. Solutions to the theoretical model were approximated by numerical methods. Both theoretical and experimental results indicate that center-line temperatures are significantly higher than boundary temperatures. Comparison of experimental and theoretical results with a cold/hot viscosity ratio 01 19:1 were in reasonable agreement. Theoretical calculations show that the effect of the temperature dependence of viscosity was very significant at ratios of 100:l to 1000:1, which are typical of those that occur when injecting hot water to flood heavy oil reservoirs. INTRODUCTION We consider the problem of prediction of fluid flow and temperature distribution in an initially cold-fluid-filled reservoir on the injection of the same hot liquid by the use of mathematical and physical models. The results reported are for a two-dimensional rectangular section of the reservoir, as shown in Fig. 1. The injection and withdrawal faces are assumed to be equipotentials for fluid flow. The ultimate purpose of such models would be to predict hot-water injection performance. However, we note that in the work presented here, one of the most significant aspects of the problem — the instabilities resulting from two-phase, water and oil flow — is not included. We will not give a historical review, but refer instead to the paper of Spillette and Nielsen,1 which contains a rather complete bibliography and critical discussion. The physical problem is exactly the same as Spillette and Nielsen, except for certain simplifications in our assumptions. The mathematical details are somewhat different, and we will present the details of our method here. The mass flow equation, which is elliptic in character, is handled by successive overrelaxation. The heat flow equation, which is parabolic in character, is handled by a straightforward explicit approximation. Some difficulty arose in the over-all heat balance due to small errors in the solution of the mass flow equation, and we feel that a different formulation of the heat flow equation would be desirable for future work. In addition to the mathematical solutions for the temperature distributions in a porous medium due to the injection of hot liquids, experimental data are presented to check the validity of these solutions. A schematic diagram of the model is shown in Fig. 2. Certain qualitative physical conclusions were obtained from our numerical and experimental results. These are: 1. Assuming high (infinite) conductivity normal to the bedding plane in the reservoir is a poor approximation, and may lead to overestimates of the total heat losses (to cap and base rock) of as much as 50 percent. 2. More heat is retained in the reservoir (per unit of heat injected) for higher viscosity changes. 3. Any particular temperature isotherm moves more rapidly along the center line for higher viscosity changes. Consequently, the approximation of temperature independent viscosity is not suitable for obtaining quantitatively correct results. MATHEMATICAL MODEL Our mathematical model is that of a reservoir of thickness 2h. The problem is idealized from that of a linear hot-water drive, and we imagine that the input face is sufficiently far away from the injection wells that the stream lines enter it normally. Similarly the production wells are far enough from the outflow face that the flow lines leave it normally. The reservoir and surrounding cap and base rock

Jan 1, 1970

By Paul E. Rosten

Introduction This papers describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Co. to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Co. operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously (Lindroos and Koski, 1966; Villar and Dawe, 1975; Koski, 1977). Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and fur¬nished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate¬kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to: (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1981

By G. Y. Chin, W. L. Mammel

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain has been analyzed by Taylor and by Bishop and Hill. The Taylor analysis is based on a principle of' virtual work, and involves finding, among numerous cotnbinalions of slip systems that satisfy the imposed strain, the combination in which the sum of the glide shears is a minimum. Previously, Taylor has treated the case of axisymmetric flow when slip occurs on (111)(110) (or {110)(111)) systems only. His analysis has now been extended by computer methods to the cases of slip on {112}(111) and {123)(111) systerns and of mixed slip on {110), {1 12), and (123) planes with a common (111) slip direction, all of which are important in the deformation of bcc crystals. The results are computer-plotted as contours of the ratio of the floe strength to the critical resolved slzea-r stress for slip, for axial orientations distributed throughout the standard stereographic triangle. Implications of the computer results to texture develop,merit, texture hardening, and dislocation theories oj work hardening are discussed. WhEN a single crystal is extended in the usual tension test, the lateral dimensions can change relatively freely. In this case, the glide shear produced by slip on a single slip system is sufficient to accommodate the (tensile) deformation. Since slip is governed by a critical resolved shear stress law (the Schmid law'), the single active slip system is one for which the stress, resolved on the slip plane and in the slip direction, is the highest among the several equivalent slip systems. This amounts to saying that a value M = U/t = y/~ is a minimum among the equivalent systems, where M is the inverse of the familiar Schmid factor (a and E refer to tensile stress and strain, and T and y refer to resolved shear stress and shear strain). A grain embedded in a polycrystalline aggregate, on the other hand, cannot freely change its shape due to constraint from its neighbors. In this case, slip from five independent slip systems (to accommodate five independent strains) is generally required.' Based on the principle of virtual work and assuming that the critical resolved shear stress for slip is the same for all systems, Taylor hypothesized that, among all combinations of (five) slip systems which are capable of accommodating the imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Again, this is equivalent to saying that the value of M = CjlyjI/ is a minimum, in analogy to the single slip case. Taylor aminimum,analyzed the case of {111)(110) slip for fcc metals, and applied the analysis to crystals undergoing axisymmetric flow, that is, the same macroscopic shape change as the poly crystalline aggregate under uniaxial tension (or compression). For the twelve equivalent {111}( 110) slip systems, there are 384 independent combinations of selecting five systems to satisfy the five independent linear equations of imposed strain.4 Taylor calculated the value of M for each combination* and obtained the active com- *A number of the independent combinations were omitted from consideration in Taylor's original work (see Ref. 5). bination (minimum M) for a number of axial orientations distributed throughout the standard stereographic triangle. Later work by Bishop and Hill*'8 showed that Taylor's least-shear hypothesis was equivalent to a maximum work principle which they advanced. Using the simplified Bishop and Hill method for {111)(110) slip, Hosford and Backofen' obtained detailed contours of constant minimum M for the same axisymmetric flow case. In contrast to {111}(110) slip in fcc metals, slip in bcc metals is generally described as occurring on {ll~)(lll), {112)(111), {123) (111) systems as well as mixed slip composed of all three. Since the direction cosines of the slip plane normal and the slip direction enter as a product in the Taylor analysis, the Taylor solutions of ,M for {110)(111) slip are identical to those for { 111} 110) slip. The other three cases of slip, however, have not been solved. In view of the numerous combinations of slip systems involved in the calculations, the Taylor analysis is clearly oriented toward computerized solutions. THE TAYLOR ANALYSIS In order to obtain the active combination of (five) slip systems by solving for the minimum value of M = we first express the (small) strain components E,, with respect to the cubic axes 1, 2, 3 ([loo], [010], [001], respectively) of the crystal, in terms of the sum of the glide shears yj from slip systems j: where n, and n,j refer to direction cosines of the slip plane normal, and dri and dsi to direction cosines of the slip direction, of slip system j, all referred to the cubic axes. In practice, the strain components are given with respect to the specimen axes X, y, 2. These components are readily converted to ers through the tensor transformation where irk and 1,~ are the direction cosines between the two sets of coordinate axes.

Jan 1, 1968

By Gerard Matthes

ONLY in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be con-templating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one-inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground-geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the :geologist or mining engineer an aerial photograph or mosaic is only a tool, the effecient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most, skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted.

Jan 1, 1928

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

By Thomas T. Read

THE fact that certain types of ore-deposits have attained their present condition through the action of descending surface waters was, perhaps, first clearly pointed out by Posepny.1 The oxidizing effects of such waters were discussed by Penrose,2 and many papers dealing with this phase of the subject have subsequently appeared. That secondary enrichment of sulphide ores, however, might be produced by descending surface waters was not clearly understood until after the copper-bearing veins of the Butte district, Mont., had been carefully studied by the geologists of the U. S. Geological Survey, al¬though De Launay3 had suggested that sulphides might be transported from point to point and re-deposited in the zone above the level of ground-water. As a result of the study of the Butte district, two papers by geologists engaged in the work appeared within a short interval. The first by Weed,4 dealing with the enrichment of veins by later metallic sulphides: and the second by Ernmons,5 treating of the secondary enrichment of ore-deposits in general. In the latter paper it was pointed out that a typical vein of sulphide ores which has been subjected to the action of descending surface waters exhibits four zones,-an upper or surface zone, in which the changes have been mainly of removal, the products being typically oxides; a second zone of oxide enrichment, in which the less soluble metals brought from above have been precipitated as carbonates or oxides; a third zone of sulphide enrichment,

Mar 1, 1906

By Bernard Kopelman

THE particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by com¬mercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature, and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. REVIEW OF THE LITERATURE Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.1 When reduction of tungsten oxides by H2 was introduced commercially, 2.1 several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-13 While these many investigations were in fair agreement on the equilibria there arose considerable controversy as to the chemical composition of the oxide between W03 and W02, because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 10o years. Thus Malguti,14 in 1835, decided it was W02.56. In 1857, Riche" proposed the formula W308. Usler,16 in 1865, confirmed the existence of W308 and further proposed W4O11. In 1897, Desi17 agreed upon W308 but also found W5014.

Jan 1, 1946

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free' from folding and faulting.

Jan 1, 1935

By Luke L. Y. Chang, Bert Phillips

ThE tendency toward further oxidation of the intermediate oxides and the high volatilization rates of the higher oxides have prevented direct attainment of equilibrium data for the system tungsten-oxygen. As a result, St. Pierre et al.1 have proposed a phase diagram (to 800°C) based on thermody-namic data to 1200°C for the known tungsten oxides (WO2z, W18O49, W20O58, and WO3) and a report on a tungsten suboxide W3O.2 Recent modification of a technique previously described3 5 now permits adequate preservation of compositions of mixtures of metallic tungsten and metal oxides (e.g., of tungsten, cobalt, calcium, samarium, titanium) in order that condensed phase relations may be established to 1700 This method has been applied to study the high-temperature stability of tungsten oxides. In the method used, the desired compositions were sealed in nonreactive containers such that only a small gas volume remained. Each sample then established its own equilibrium atmosphere at temperature. This method has advantages in the study of systems of the W-0 type where knowledge of the condensed phases is desirable but for which composition and pressure of the gas phase are not readily attainable because of oxide volatility. Mixtures of 99.99 pct tungsten metal powder and purified tungsten anhydride (WO3) or in some cases W18O49* were equilibrated in pellet form in sealed

Jan 1, 1964

By Homer Griffield Turner

The nature and comparative features of anthracite and bituminous coals have been discussed by the writer in two previous papers.' Although this paper is offered as a further contribution to the subject, it seems desirable at the outset to repeat some of the descriptive matter of the early works in order to show the actual connection between various constituents of both coals and the new photomicrographs and other physical and chemical properties. Structure of Anthracite and Bituminous Coals A lump of bituminous coal (Fig. 1) is readily seen to be composed of layers differing from one another in texture, luster and thickness. There are, in general, three kinds of layers, although only two are usually seen. One is deep black, very compact, and has a bright luster; another is grayish black, has a duller luster and is less compact; the third is black, dull and porous in appearance, but because of its thinness is not often seen except on parting surfaces. This last material is charcoal. American students of coal morphology use the names anthraxylon, attritus, and fusain to designate these three constituents of laminated coal. Anthraxylon refers to the brightest bands, attritus to the duller layers, and fusain to the charcoal. Close examination of a lump of bituminous coal shows the brightest deep black layers to be embedded in the duller grayish black laminae. These deep black layers are lens-shaped and vary in thickness from thin sheets to over half an inch. They are often so continuous through the lump that their tapering terminae are not noticeable. On careful examination the duller grayish black laminae (Fig. 7) are seen to contain many very thin sheets of this very bright black material. The charcoal

Jan 1, 1930

By E. A. von Hahn, T. R. lngraham

Cementation rates ulere studied by rotating an elec-tropolished or etched copper strip in aqueous solutions, of either perchloric acid or alkaline cyanide, containing silver ions. The rates of cementation were more rapid in acidic media than in cyanide media. In both, the rates varied with the rate of rotation of the copper strip. The deposits formed in the acidic solutions were finely divided, loosely adhering powders. Those formed in the cyanide solutions were dense and adherent. The presence of the deposits influenced the cementation rates. In the acidic solutions the rate was enhanced, possibly because of the increased cathodic area. In the alkaline solutions the rates were decreased in the presence of the deposits. This has been attributed to restricting the diffusion of the copper ion from the rnetal outward into the bulk of the solution. In an earlier paper1 the authors described a kinetic study of the cementation of palladium on copper in perchloric acid solutions. That work indicated that there were two stages in the palladium cementation process. The first, more rapid stage was consistent with rate control by the diffusion of Pd11 ions to the copper surface and/or by chemical reaction at the surface. The second stage was consistent with rate control by the diffusion of copper ions from the copper surface, through the deposit, out into the main body of solution. The effect of the type of deposit on the rate of cementation is of particular interest because it may be one of the primary features involved when large quantities of metal are to be cemented from solution. No substantial investigations of the effect seem to have been made. Accordingly, an extension of the previous work was arranged to study the cementation of silver on copper. This system was selected because of the convenience of the analytical methods, the previously established technology with copper, and the fact that the system could be studied in both acidic and alkaline media. By selecting perchloric acid and alkaline cyanide solutions as the media, it was hoped that some assessment might be made of the effects, on cementation, of having the silver ion present in a virtually uncomplexed state and in a highly complexed state. EXPERIMENTAL The cementation rates were studied, as previously described,' by rotating a copper strip (1.0 by 23.2 cm) clamped to the peripheral surface of a lucite cylinder. The solutions were kept at constant temperatures (±0.05°C) under an atmosphere of purified nitrogen, and samples were taken periodically for analysis. The initial solution volume was 1000 ml and the sample volume 5 ml. The initial silver(1) ion concentrations were made low (0.5 to 1.0 x 10-4 moles per liter) to minimize the influence of the cemented deposit on rates. The solutions were prepared by dilution of suitable aliquots of silver perchlorate and silver cyanide stock solutions. Both stock solutions were prepared from purified silver powder (Johnson, Matthey, and Mallory Ltd.) with redistilled deoxygenated water, and they were kept under an atmosphere of purified nitrogen. To prepare the stock solutions, weighed amounts of silver powder were dissolved with nitric acid. For the AgC104 stock solution the silver nitrate solution was evaporated twice to near dryness with perchloric acid and then made up to volume: For the NaAg(cN)2 stock solution, the silver ions were precipitated with sodium hydroxide solution. The precipitate was filtered, washed thoroughly with redistilled water, dissolved with 1.1 times the required stoichiometric amount of sodium cyanide solution, and made up to volume. The small amounts of free perchloric acid and sodium cyanide present in the stock solutions were disregarded in the preparation of the solutions. The copper strips were cut accurately from 0.025-in. sheet (American Metal Climax OFHC brand) and annealed for 1.5 hr at 470°C in a stream of nitrogen. Analyses of the solution samples for silver and copper were done with a Techtron Model AA-3 atomic absorption spectrophotometer. Calibration standards of the same composition as the experimental solutions were prepared and analyzed simultaneously with the samples. No difficulty was experienced in the analyses, and the reproducibility was within 1 to 2 pct in both alkaline cyanide and perchloric acid solutions.

Jan 1, 1968

[NORTH AMERICA UNITED STATES ALABAMA America.-Dyar, 0. C. Anniston.-Klugh, B. 0. Ashland.-Pallister, H. D. Auburn.-*Poor, R. S. Bessemer.-Creveling, J. 0. Lindstrom, W. A. McKenzie, W. 0. Mitchell, F. R. Birmingham.-Abbott, C. E. Aldrich, T. H., Jr. Armstrong, 0. R. Beard, A. H. Benjamin, F. S. Blackburn, E. 0. Blair, A. J. Blair, 0. S. Blair. H. W.]

Jan 1, 1946

By William F. List, Marvin A. Schuster

Monolithic electrooptical mosaics of 2500 photo-transistor elements with internal row and surface column interconnections have been fabricated by epitaxial-planar diffsion techniques. Unique access to any elemed of the mosaic is provided through one of the fifty X and one of the fifty Y external leads. The sensor mosaic can be used for imaging applications and has a 1:1 aspect ratio, a resolution of 100 lines per in., a dynamic range in excess of lo3, a sensitivity of 0.5 per pw, element response within a 2:l range over 75 pct of the mosaic, and a minimum detectable signal of the order of 10-' w. Design considerations which ilnpose particclar fabrication yequirements are disctussed along with some of the problems peculiar to the epitaxial and planar-dijfision techniqes by which this device is fabricated. The solid-state silicon monolith has an imaging area of 0.5 by 0.5 in. and an element center -to- center spacing of 0.010 in. J monolithic solid-state electrooptical device has been developed as the photon-sensing mosaic for use in an image-converter system.' This system is the solid-state equivalent of the vidicon and can image radiation in the visible and near-infrared regions of the spectrum. The electrooptical image converter has the desirable size, weight, reliability, and low-power characteristics inherent in solid-state devices. It is read out by direct-wire means rather than by beam-scan techniques. The packaged unit is shown in Fig. 1. A selection of material for the sensor was based on considerations of both reliable fabrication techniques and material spectral response. Silicon was selected both for its response from the lower end of :he visible to the long-wavelength cut-off above 11,000A and for its well-developed epitaxial planar-diffused technology. The electrical image is composed of M x N discrete information bits with each bit emanating from one of the individual phototransistor sensors. The interconnected mosaic concept was introduced to provide a structure which is both manageable in its number of leads and compatible with conventional viewing systems which accept XY data. Interconnections along the Y direction are provided by internally diffused strips, while interconnections along the X direction are formed by vacuum-deposited metal surface bars. Unique access to any individual element of the M x N mosaic is available through one of the M and one of the N external leads. PHOTOTRANSISTOR DESIGN A phototransistor structure2 was selected for the discrete photon detectors of which the mosaic is com- posed. Basically, the mode of phototransistor operation is such that incident quanta are absorbed in the base area of the element where they generate electron-hole pairs. If the electrons are liberated within a diffusion length of the depletion region around the collector junction, they will diffuse to this depletion region and be swept across the junction where they account for a small component of the photocurrent. Similarly, the holes which are created within a diffusion length of the emitter junction will diffuse to this region where they forward bias the emitter and so induce injection of minority carriers into the base. This accounts for the substantial transistor photocurrent. This mechanism of operation implies several design and fabrication goals for the individual sensor elements: high electrooptical conversion efficiency, sufficient carrier lifetime in the base regions, and a maximum volume in which photons can be absorbed within a diffusion length from the depletion layer about the junction. Moderately high transistor gain is desirable to permit readout at low light levels; however, very high gain has a deleterious effect on mosaic dynamic range. The mosaic must also be characterized by good uniformity of element response as well as by good isolation between elements. The above set of conditions imply that junction depths must be optimized with respect to photon ab-

Jan 1, 1967

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

By Holt, Grover J.

PRIOR to :1937 any discussion of mining and transportation in the iron mines of Minnesota would have been limited largely to conventional methods which have been used for years in the iron ore industry. Today, however, an inspection trip to the crest of almost any open pit on the ranges will re- veal great progress underground mining and the transportation of underground ore have also developed rapidly and if and when underground mining of iron ore again becomes generally economically feasible; these mining methods will probably witness a transformation equal to that which has taken place in the open pits.

Jan 1, 1941

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,' and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By Frances Hurd, Clark

Iv 1897, Roberts-Austen(l)$ found an arrest in the thermal curves of alloys of 60 per cent. copper and 40 per cent. zinc. This break occurred from 450° to 470° C. Shepherd, (2) working in 1904, was unable to detect any change in the direction of the thermal curve. In 1911, Carpenter and Edwards(3) confirmed the work of Roberts-Austen and called this a eutectoid transformation of beta to alpha plus gamma. Hudson') in 1914, showed that the beta constituent could be produced synthetically at temperatures below the transformation point. He believed the change in the beta was polymorphic in nature rather than a eutectoid. The work of Matsuda(32) in 1922 demonstrated this break by thermal analysis, microscopic investigations, dilatation, electrical resistance measurements, and a thermoelectric study. He believed the transformation to be continuous from 300° to 480° C., and comparable to the A 2 transformation in iron. Later, in 1924, Andrew and Hay, with electrical resistance measurements, confirmed Matsuda's work. Imai(28) showed the transformation to be progressive and therefore a function of the temperature rather than the time. He stated that it was neither a eutectoid nor an allotropic change of phase. Atomistically expressed, it was a change, not of atomic configuration, but of atomic energy of some kind; and again it was compared to the A 2 transformation in iron. Imai believed that his analyses by X-rays led to the same conclusion. In order to study this change, at 470'C., in homogeneous 60:40 brass, Homerberg and Williams «0> and Homerberg and Shaw(41) quenched their material in iced brine to obtain the beta solid solution and reheated at various temperatures. At 200° C., a change in the microstructure and physical properties occurred. A fine-grained structure, which they termed alpha and which had the appearance of a sorbitic steel, appeared, with an increase in the tensile strength to 82,750 lb. per sq. in., and a Brinell ball hardness of 240 with 3000 kg. load. At 470° C., the alpha

Jan 1, 1927

By G. W. Healy, W. Craft, D. C. Hilty

By means of a theoretical extension of the Cr-C temperature relation in molten chromium steels to low chromium contents and by a correlation of the ratios of chromium to iron in the slag and metal, a method has been developed for estimating the amount of metallic oxidation during the oxidizing period of a chromium steel heat. Application of this method has indicated that due to temperature limitations metallic oxidation may be excessive for very low carbon steels charged with more than a small amount of chromium. IN the melting and refining of chromium steels the oxidation of carbon to a low level is accompanied by the oxidation of chromium and iron in considerable amounts. For the subsequent recovery of chromium and associated iron from the slag, the amounts of metal oxidized must be known for efficient reduction and control of composition. Further, in order to arrive at an accurate understanding of the process, so that chromium-bearing scrap can be used effectively, information is required on the relation between composition of the charge and weight of metal oxidized to reach the desired carbon content. Crafts and Rassbach1 recently developed an empirical relation between chromium, iron, and manganese oxidized per ton of steel charged, and final carbon content and temperature. This relation did not show any dependence on amount of chromium charged. However, it was felt that such a dependence might be present, so a further analysis of the data was undertaken. Cr-C Relation at Low Chromium Levels Crafts and Rassbach's results were based on temperatures estimated from the Cr-C relation previously established experimentally by Hilty,2 and on a single temperature observation (immersion thermocouple) on a heat made at low temperature from a charge of carbon steel scrap containing only a small amount of residual chromium. The temperatures estimated from the Cr-C relation were for heats charged with chromium-bearing scrap and which contained substantial amounts of chromium (2 to 10 pct) at the end of the oxidizing period. No data, other than that from the low temperature heat just mentioned, were available for the low and intermediate chromium ranges. In order to extend the range in which temperature may be estimated, the Cr-C relation requires further consideration. The Cr-C relation, expressed as suggests that carbon is zero at zero chromium in the bath. This is obviously absurd, because as chromium approaches zero the carbon content must approach the limit established by the Fe-C-O equilibrium. It is evident, therefore, that the Cr-C relation as defined by Eq. 1 is not valid below some minimum chromium content that may vary with temperature. On the other hand, it is probable that any such limiting chromium content is less than 4 pct at 3200°F, since the experimental data from which the Cr-C relation was derived included several observations at that level with no deviation. In any event, it is apparent that further evaluation of the results presented by Crafts and Rassbach is dependent upon a means for estimating the Cr-C temperature relation in the low chromium region. From the observations of Chen and Chipman9 and thermodynamic data given in Basic Open Hearth Steelmaking,4 the following relation can be calculated for melts containing small amounts of chromium and carbon assuming a carbon monoxide pressure of 1 atm: % Cr -21,250 K' = (%C)2; logK1 == —t— +13.88 [2] Moreover, by plotting Eq. 2 for any given temperature on cartesian coordinates, it can be extrapolated graphically to the limiting carbon content at zero chromium for the specified temperature without serious complications. By means of Eq. 2 and its extrapolation, the Cr-C temperature relations originally established experi-

Jan 1, 1954

By P. W. Andrews, R. B. Toombs

ECONOMIC STRUCTURE OF MODERN INDUSTRIAL ECONOMIES The role of minerals in modern industrial economies may be examined in several ways. There are relationships with the various sectors of the economy: the primary, secondary, and tertiary industrial groupings and activities. Mineral supply and demand activities can be measured in terms of national accounts criteria. The economic policy objectives of the modem industrial economy are based to a considerable extent on the needs of the nation for economic supplies of miner- al materials. There is an important role for minerals relative to national security in peace and in wartime and many national policies are directed toward ensuring adequate sup- plies of minerals. Environmental control in the modem industrial economy is increasingly concerned with matters related directly to the production and use of minerals and these matters, in turn, bear importantly on conservation in mineral supply and demand. Mineral polices include specific provision for research and development activities concerned with the production and the use of minerals. In all, national policy objectives will be shaped in considerable part by the circum- stances of mineral supply and demand: the relative degree of availability from domestic and foreign sources, the state of the mineral-processing industries, and the degree of development of the mineral-using industries, and per capita and total changes in requirements. Goods made from mineral raw materials are the basis of all advanced societies and although this is taken for granted, every country is continually dealing with problems of mineral supply and demand. Considering that in the first 50 years of this century the consumption of mineral materials in a highly Industrialized country such as the United States increased by six times while the population was doubling, it becomes apparent that if a country is to enjoy rapid economic growth it must have access to huge and ever-growing supplies of mineral materials at lowest possible cost. Adequate supplies of mineral materials and wise usage of mineral resources have always been among the most important determents of a nation's survival The importance of access to adequate mineral supplies is increasing every year and this has significant international, as well as national, implications because of the unique locational characteristics of mineral resources. It is generally acknowledged that no particular type of natural resource is essential to a high level of national income or to economic progress. A country's endowment of natural resources need not exercise a determining influence on the course of its national income over time, provided it is able to trade. What is required for economic progress is the availability of a substantial quanti-

Jan 1, 1976