Search Documents

By T. Sekimoto, T. Kokubo, M. Yamamoto, K. Masuda, T. Moro, H. Sakamoto

The choking-free cyclone was developed primarily to remove solid particles suspended in a slurry containing fibrous materials, such as municipal solid waste. This cyclone is characterized by a screw conveyor at the underflow side of the cyclone. The screw conveyor has a hollow rotational shaft for air supply and is driven by a variable speed motor for discharge control. Even if the underflow discharge is highly concentrated, this type of cyclone can be stably operated without nozzle choking. High classification efficiency similar to that of a conventional cyclone can be obtained as a result of air introduction through the hollow rotational shaft. The recovery of organic matter and the removal efficiency of inorganic matter were actually improved by the application of this cyclone to municipal solid waste. After applying this cyclone to the desliming of fine sand, sand product of low water content was recovered.

Jan 1, 1980

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By P. F. Allen

WITH capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distribution of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced. The tailing disposal area for the Morenci concentrator lies south and southwest of the concentrator building. Ample storage space is available. A wide valley contains three sharply defined ravines lying on an average slope of 4 pct. The more central of these ravines, and the largest of the three, is known as Morenci canyon, which provides substantially more tailing storage area than the other two. Stargo canyon lies to the west; the other is appropriately named East canyon. Total area of the tailing disposal site is nearly 31/4 sq miles, or about 2000 acres. The storage area in use was somewhat more than 850 acres at the end of 1954, or 16 acres per 1000 tons of tailing to be stored daily. At the present time none of the east side dams are in regular use but they are available in emergency. There are five dams on the west side (in Morenci and Stargo canyons) as well as two auxiliary dams adjacent to No. 4 West and No. 5 West. This has made it possible to concentrate men and equipment in a smaller area with consequent savings in both manpower and machinery. Tailing Thickening: Tailing from the flotation process reaches the thickeners with a solid content of about 18 pct. The launder carrying this pulp is subdivided at a central point into seven launders carrying a proportional share to each of seven tailing thickeners, which are located in Morenci canyon close to the concentrator. Five of these thickeners are 300 ft diam and two are 325 ft diam. Thickeners are of the peripheral traction type and rakes travel at the rate of one revolution in 37 to 39 min. The entire installation provides 500,000 sq ft of settling area, or approximately 101/2 sq ft per ton of tailing to be thickened daily.

Jan 1, 1957

By Claus Goetzel

THE object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion AVERAGE COEFFICIENT PER DE G. C. OVEN RANGE 20° To 200° C. Pure aluminum '31.6 X 10-6 Cast low-expansion Si-Cu-Ni-Al piston alloy 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.10-1.0 Mn) 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si) 12.8 X 10-6 Pure silver 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render it use feasible in Germany as an emergency in is- tire. The coefficients of linear expansion of several metals and alloys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850° C. for the solidus of the silver alloy. Pure silver melts at about 961° C., so that the Fin. 1.-PISTON CONTAINING tolerable depression in the solidus is rather FERRONICKEL INSERT. small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937

By M. Cross

INTRODUCTION The results of the Japanese dissective investigations have [l-4] transformed our understanding of how the blast furnace operates. These studies revealed an internal structure of the furnace burden with five main zones, as illustrated in Figure 1. In the granular zone the charged material retains its structure whereas in the cohesive zone the iron ore particles are at advanced stages of reduction and form a semi-molten mass with a relatively high flow resistance. In the active coke zone molten iron and slag flow through a matrix of loosely packed coke. The raceway is a relatively small void space generated by displacement of coke due to the hot blast momentum, whilst the hearth is packed with coke, slag and molten iron. [ ] It is now well appreciated that furnace control is largely achieved and maintained by using the burden charge distribution to determine the gas glow distribution within the furnace and, hence, the shape and extent of the cohesive zone. In fact, Wakayama et a1 [5] of Nippon Steel Corporation state that optimum furnace operation is synonomous with the formation of a desirable cohesive zone shape, which in turn is almost solely determined by the burden charge distribution and its mechanical properties [6]. Much of the development work on operating furnaces since the dissective investigations has been oriented towards the identification of external furnace measures which reliably predict the shape of the cohesive zone. Currently the most popular measures are top gas temperature, velocity and CO/CO, ratio profiles [5]. More recently pressure distributions as evaluated from a series of wall measurements down the height of the furnace are also being utilised [7] to identify the position and shape of the cohesive zone. A great deal of emphasis has been placed upon achieving a consistent quality in the burden charge materials, establishing a suitable set of operating conditions and only making changes when forced to, ie., the operation for some reason moves outside a desired operating range or the production requirements change. Operational control schemes based upon this philosophy (eg., Kawasaki's GO-STOP system [8]) have been remarkably successful at achieving both high production rates and relatively low fuel costs. Mathematical models have long been used as tools to assist in the analysis of the blast furnace process. Although, the models have been useful in post-operative analysis and for identifying trends, etc., they have not proved reliable for detailed design criteria or as the basis for effective control schemes. Such mathematical models have moved from simple statistical correlation, through overall and stagewise heat-and-mass balance calcu-

Jan 1, 1984

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm's fluorspar operations in the same area.

Jan 2, 1953

Jan 1, 1970

By Blandford C. Burgess

Mica is an orchid among minerals. It is formed in pegmatites, one of the most bizarre of igneous formations, and is exceeded by few other minerals in the perfection it may attain as to size, color, and cleavage. First used for window glazing, as an ornament and article of trade, it has become one of the most essential insulators of electricity, heat, and shock. Most internal combustion engines use mica condensers or capacitors and such machines of war as planes, tanks, and submarines are immobile without it. The original manuscript of this guide was written in April 1943 at the peak of war emergency. It was not used be- cause shortly thereafter a decision was made to buy on a one price basis eliminating differentials for both quality and size. This is now presented with the thought that from the standpoint of preparedness we can only consider an- other war imminent and every effort should he made to set up in usable form the experience gained during the Second World War. Colonial Mica Corp. was set up by Metals Reserve Co. as a wholly owned government agency to encourage production of domestic mica and to purchase it. It soon became the exclusive buying agency for such mica. The writer as Southern Manager called on all the private agencies buying mica to assist in formulating buying policies, methods, and prices.

Jan 1, 1949

Jan 1, 1963

By G. Thodos, R. B. Grieves

A method has been developed for the accurate calculation of the cricondentberm and cricondenbar temperatures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain any number of components including paraffins and isoparaffins, olefins, acetylenes, naphthenes and aromatics. This approach is based upon the mole fraction of the low-boiling component in the mixture and graphically presents the ratios of the cricondentherm and cricondenbar temperatures to the pseudocritical temperature as {unctions of a boiling-point parameter. The only requirements are the critical temperature, normal boiling point and the approximate vapor pressure behavior of each component. For mixtures of more than two constituents a stepwise calculation procedure is necessary where the pseudocritical temperature is based upon the critical temperature of the pure low-boiling component and upon the actual cricondentherm or cricondenbar temperature of the mixture of all the remaining higher-boiling components. From an analysis of 22 binary systems (123 compositionsl, the average deviation of calculated cricondentherm temperatures from reported values is 0.87 per cent, based on degrees Rankine; and for 10 multicomponent mixtures containing from three to six components, the average deviation is 0.98 per cent. From an analysis of 18 binary systems (104 compositions) the average deviation of calculated cricondenbar temperatures from reported values is 0. 79 per cent; and for 15 multicomponent mixtures, 1.47 per cent. Equations, derived from the graphical relationships, are presented which enable rapid calculations for both binary and multicomponent systems. INTRODUCTION With the increasing tendency towards the use of high pressure processes, the need for an accurate method of calculation of the properties of a multicomponent hydrocarbon mixture in the critical region is becoming more essential. Critical region phase relations are also significant in gas condensate reservoirs, for which a knowledge of the fluid phase boundaries and regions of retrograde condensation make it possible to evaluate optimum operating conditions. The possibility of liquefaction in the underground structure may be established, and information on the feasibility of the use of repressurizing may be determined. A typical phase diagram for a multicomponent hydrocarbon mixture is presented as Fig. 1. This figure also shows the regions of retrograde behavior encountered by following lines AB and AC. If accurate methods of calculating the temperatures and pressures at the critical, cricondentherm (maximum temperature) and cricondenbar (maximum pressure) points of multicomponent hydrocarbon mixtures of known composition were available, it would be possible to estimate closely the entire phase diagram of any mixture. Several methods have been presented in the literature for the estimation of the critical temperatures and pressures of multicomponent mixtures containing all types of hydrocarbons and including the fixed gases.4-8,21 Considering the cricondentherm and cricondenbar points, the work is more limited. Etter and Kay5 have developed rather complex equations for

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

By R. G. Burdick, W. R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abondoned coal mines also imposes potential hazards in current underground mining operations, since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive manmade tunnels in previous work has led to the development of a surface-operated automatic earth resistivity survey system and associated computer data reduction process for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to-diameter ratios greater than 10 to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting abandoned coal mine workings. The hardware and software aspects of third new system are described together with applications of the method for surveying and mapping abandoned coal mine workings. Field tests are presented to illustrate the detection of both air-filled and water-filled mine workings.

Jan 1, 1984

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

[ ]

Jan 1, 1938

By F. Keller, E. H. Dix, L. A. Willey

The consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathewsi and by Tammann.2 Canlpbell and mathews described principally the beginning of solidification. They found the curve of beginning of solidification rising gradually from the melting point of pure alunlinum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AISb. The curve then drops to the melting point of pure antimony. Tamrriarln explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AISb. The space lattice of the compound AISb, according to Owen and Preaton,³ is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony. The Present Investigation It has been the purpose of this investigation to determine the solid solubility of antimony in aluminum and also to investigate the eutectic temperature and concentration. The experimental work has been carried out in a manner similar to that described in a previous paper4 from this laboratory.

Jan 1, 1931

By William E. Ford, Edward Salisbury Dana

Secondary Twinning. - When there is reason to believe that the twinning has been produced subsequently to the original formation of the crystal, or crystalline mass, as, for example, by pressure, it is said to be secondary. Thus the calcite grains of a crystalline limestone often show such secondary twinning lamella?. The same are occasionally observed (Ilc, 001) in pyroxene crystals. Further, the polysynthetic twinning of the triclinic feldspars is often secondary in origin. This subject is further discussed on a later page, where it is also explained that in certain cases twinning may be produced artificially in a crystal individual - e.g., in calcite (see Art. 282).

Jan 1, 1922

Jan 1, 1968

By G. R. Mansfield

THE geologic structure of the Idaho phosphate field has an important bearing on the classifica-tion and the exploitation of the lands that contain phosphate. Maps and structure sections1 recently made available show that the phosphate is mainly preserved in downfolded or downfaulted areas. Since the phos- phate beds are generally rather soft and lie between harder and thicker formations they have been forced to adjust themselves to these formations during epochs of disturbance of the earth's crust, so that they are frequently affected by minor folds and by faults which may help exploitation by producing undue thickness at certain places or may hinder it by cutting out the phosphate at other places where according to expecta-tion it should be present. A particularly important structural feature which affects both the distribution and the exploitation of the phosphate beds is the great Bannock overthrust by which one or more slices or blocks of the earth's crust have been pushed over other blocks like ice cakes on a pond. Thus in this region a great flap of folded rocks lies across other rock structures for a distance of approximately 35 miles. Most of the commercially accessible phosphate deposits, shown in the maps that accompany the report cited, are in this flap, which con-stitutes the upper block of the overthrust. In some places, however, the phosphate in the lower block is also accessible. In both blocks post-phosphate rocks exposed at the surface here and there indicate that phos-phate beds may lie at greater or less depth below. The presence of the Bannock overthrust beneath much of the area reported is known by the occurrence of windows in the upper block both within the quadrangles mapped and in areas farther west. The portions of the lower block exposed in these windows show stratigraphic dis-cordance with the surrounding formations. The depth of the fault plane at most places, however, can be told only by drilling or actual mining. Some of the folds in the upper block are relatively deep and it seems fairly certain that the phosphate that may originally have been present in their deeper parts has been removed by thrust faulting. The estimates of phosphate reserves in folds liable to be affected by the Bannock overthrust may therefore need ultimate revision depending on the depth of this fault plane, as it may subsequently be ascertained.

Jan 1, 1928

By F. A. Olson, S. L. Pohlman

A unique method of measuring weight loss as a function 3 of time, with a sensitivity of 10-5 grams, while leaching copper minerals with a flowing acid leach solution has been developed. Kinetic results obtained coupled with visual and microprobe analyses show topochemical reaction for the leaching of chrysocolla with sulfuric acid. The kinetics follow a shrinking core model and show ion diffusion through a product layer, chemical reaction at the unreacted core interface and mass transfer through the boundary layer as being important.

Jan 1, 1974