Search Documents

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By R. V. Smith

The theoretical background for calculating friction factors for flow in gas wells by two methods is presented. The first method, requiring pressures, temperatures and specific volumes of the flowing fluids at various depths in the well bore, shows how the mechanical-energy-balance equation for vertical flow may be graphically integrated over the actual path of the expansion of the fluid in the well. Thus, assumptions regarding the effective temperature and effective compressibility of the fluid in the well are avoided. The second method presents an equation derived on a basis of the assumptions that both the temperature and the compressibility are fixed at constant effective values throughout the flowing column of gas. The second method provides a convenient and practical means of calculating friction factors for gas wells and lends itself readily to the problem of calculating subsurface pressures in a flowing gas well. The application of both methods to actual test data taken on a flowing gas well is illustrated in the paper. INTRODUCTION As friction factors for the producing strings of flowing gas wells cannot be measured directly and must be calculated from flow-test data, study of the methods of arriving at friction factors is a necessary adjunct to understanding the characteristics of flow in gas wells. There are two methods of calculating friction factors for gas wells; they differ from one another mainly in the treatment of the path of expansion of the fluid in the well. In the flowing well, the energy consumed in lifting the fluid from the bottom to the top of the well, overcoming the friction between the moving fluid and the pipe walls, and increasing the velocity of the fluid as it flows up the producing string is supplied by expansion of the flowing fluid. The available energy is determined by the expansion of the fluid that follows a path determined by conditions of temperature, compressibility and phase changes of the fluid during the expansion. A means of evaluating the available energy in a flowing gas well and determining the proportion of the available energy used in lifting the gas, overcoming friction, and increasing the velocity of flow is developed in this report. Knowing how much energy is consumed in overcoming friction makes it possible to calculate friction factors for given flow rates in given sizes of pipes in wells. Friction coefficients, as used in this report, are dimension- less proportionality multipliers used in the flow equations to satisfy the equality between the terms of the equation. The square root of the reciprocal of the friction coefficient is termed the friction factor. It has been known for many years that friction factors may be computed directly from mathematical formulas based on certain assumptions regarding the temperature and compressibility of the moving fluid in a well. A general equation is presented in this report without assumptions for vertical flow of fluids and a conventional-type equation is derived on the basis of assumptions that fix the temperature and compressibility at constant values. Accurate pressures at the sand faces in wells are required in the method of determining the productivity of gas wells, as outlined by Rawlins and Schellhardt1 in Bureau of Mines Monograph 7. Where measurements are not made with subsurface-pressure gauge; or static gas columns are unavailable, flowing pressures customarily are calculated at the sand face in the well by the use of the well-known Weymouth formula1. Natural gas engineers have realized that errors introduced by the use of friction factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; they also know that such factors are important considerations in testing large-capacity gas wells. Accordingly. present research on the productivity of gas wells at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla., is being directed toward measurement of the pressure loss due to friction in flowing gas wells. It is beyond the scope of this report to show how friction factors vary with rate of flow and in pipes of different diameters, as it is intended only to develop and illustrate the use of mathematical expressions for calculating friction factors from flow-test data. The equations presented apply only to turbulent flow in circular pipes. ENERGY RELATIONS FOR FLOW OF FLUIDS2 The concept of conservation of energy is usually the basis of any study of fluid flow through vertical pipes as in gas wells, horizontal pipe lines, or orifices. In deriving equations, the following symbols are used:

Jan 1, 1950

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsoli-dated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries. In the Magnet Cove area of Hot Spring County, Ark., the titanium minerals include rutile, brookite, ana- tase, leucoxene, and others. They occur in soil, clays, and altered rocks adjacent to novaculite in contact meta-morphic deposits. In preparing titanium minerals for use in the industry, it is necessary to know the physical characteristics of the ore. Also it is believed that the particular physical character of the titanium mineral used is just as important as the chemical character. Brookite and rutile, for example, are the same chemically but differ in crystalline structure. In preparing titanium minerals for market, beneficia-tion is necessary. For the millman to make a satisfactory laboratory test, the sample he uses must be as nearly of the same physical character as he would have from mine run ore. In the past at Magnet Cove, churn drilling had been done on the properties, and assays of total titania had been obtained. It was found, however, that the total titania was indicative merely of the presence of titania but did not tell the metallurgist the character of the material or even give him the slightest indication of what he might expect to recover. When the Bureau of Mines entered the field in the winter of 1947 and 1948, it was therefore necessary that a natural sample be recovered. LIMITATlONS IN ORDINARY PRACTICE The churn drilling that had previously been done had shown that the occurrence of titanium-bearing mineral was somewhat widespread. The samples were, however, completely beaten up and in a finely powdered state. The minerals had been slimed, and such ore dressing tests as were made from the churn-drill samples were found to be worthless. Test pitting and outcrop sampling had provided satisfactory samples of surface ore but did not represent the entire ore body. A quantity of rutile had been produced from the surface residual concentrations in the westerly part of the cove, but production ran into metallurgical trouble as depth was attained. Representative deep samples upon which ore dressing research might depend were needed.

Jan 1, 1950

By F. A. Forward, J. Halpern

A new process is described for extracting uranium from ores containing sulphidic minerals, which comprises treating an aqueous pulp of the ore with air or oxygen at elevated temperatures and pressures. The acid required to dissolve the uranium is generated during the leach through oxidation of the sulphides. The chemistry of the process is discussed and laboratory results are presented to illustrate the operation of the method and the variables which control it. With most ores, leaching at a temperature of 130°C and an oxygen partial pressure of 10 psi provides uranium extractions of 90 to 95 pct in 4 to 6 hr. The acidity and level of dissolved impurities in the leach liquor can be kept fairly low. The method is characterized by a number of advantageous features including low reagent cost, short retention times, and high recoveries. RECENTLY there have been developed several processes for extracting metal values from ores by pressure leaching techniques;' -' an example is the carbonate leaching process for uranium ores which has been studied in this laboratory.' Leaching is carried out under oxygen pressure to ensure oxidation of the uranium to hexavalent compounds which are soluble in carbonate solutions. During the course of investigations relating to this process, it was observed that sulphide minerals, such as pyrite, usually were oxidized under the conditions of the leach treatment resulting in the formation of iron hydroxides and sodium sulphate, i.e. 2 FeS= + 7Vz O2 + 8 Na,CO3 + 7 H,,O -* 2 Fe(OH)3 + 4 Na2SO4 + 8 NaHCO.,. [1]

Jan 1, 1956

By Clifford Frondel

THE aluminum oxide known as corundum has several varieties that have been used as gem materials since ancient times. These include the red variety called ruby, the blue variety sapphire, and the asteriated types of ruby and sapphire. Asteriated sapphire was known to the ancients under the name of astrios, and descriptions of this gem were given by Pliny and other early writers. The relation of these gem materials to each other as varieties of a single species, corundum, was first clearly established by Haüy in 1805 and J. M. Güthe1 in 1809. Natural gem corundum is obtained principally in Ceylon, Siam, Burma, India, and Australia. Star sapphires and rubies always have been highly prized and in recent years have become particularly popular in the United States. Natural star rubies of large size and fine quality are extremely rare and rank with large and fine emeralds and diamonds as the most valuable of gem stones. Interest thus attaches to the recent success in commercially synthesizing star sapphires and rubies of a size and perfection unmatched by nature.

Jan 1, 1954

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulageways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Edward Saibel

THE object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. THEORY OF FRACTURE In the thermodynamic theory of the fracture of metals developed earlier,1 it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form u ± uo = JLm?AV/V [1] where Lm, is the latent heat of melting of the unit volume, ?V/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, [uo] is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will be assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. 1. If the point of intersection of the straight line with the axis of zero strain is represented by so, and the slope of the straight line is p, the analytic form of the flow curve is [s = s + pd [2]] and the strain energy per unit volume evaluated from [JvdS] becomes (vsod + pd2/ 2). When this latter term reaches the critical value JLm?V/V (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: [s1 = \/C r.2 + 2Mp [31] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. FLOW AND FRACTURE CURVES Ludwig2 attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1947

PUGET SOUND LOCAL SECTION. Executive Committee. CHESTER F. LEE, Chair roan. C. R. CLAGHORN, Vice-Chairman. JOSEPH DANIELS, Secretary-Treasurer, University of Washington, Seattle, Wash. W. C. BUTLER. AL K. RODGERS. On the evening of Tuesday, Sept. 2, an informal dinner was held at the University Club, Seattle, Wash., at which the Secretary of the Institute was present, and a valuable and interesting conference took place concerning the recent activities of the Institute and the relations of the Institute management to the Local Sections. SOUTHERN CALIFORNIA LOCAL SECTION. Executive Committee. THEODORE B. COMSTOCK, Chairman SEELEY W. MUDD Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 300 Germain Building, Los Angeles, Cal. C. COLCOCK JONES. FRANK ROBBINS. Maintains headquarters at 300 Germain Building, Los Angeles, Members of the Institute are invited to visit these headquarters whenever they are in the city. A reception was held at the headquarters of the Section on Wednesday, Sept. 10, at 8 p.m., to meet the Secretary of the Institute and discuss Institute activities and affairs. Light refreshments were served, and about 20 members of the Section attended.

Jan 10, 1913

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

Jan 1, 1873

By W. T. Thom

All engineering education is faced by certain basic problems, three of which seem to have particular present importance in geological engineering training in general, and in respect to training for oil field geo-exploratory work in particular. Problem i The first of these problems has to do with present and future educational objectives and with the numbers and qualities of the men who should be coming out of our geo-exploratory training programs. Before the war we needed ever-increasing numbers of graduates at the Bachelor's level and a very much smaller number of men who had reached the Doctorate degree. Now, with more difficult, more extensive, and more costly exploratory work; with a rapid expansion of company "staff" activities, and with the initiation of many new research organizations and laboratories; it is clear that men of exceptional ability will be more and more in demand, and that the schools will need to carry a greater proportion of their students through to the Ph.D, degree. Problem 2 Assuming that the mineral industries will need an increasing supply of well-qualified Ph.D.s for future geoexploratory work (staff, line and research), can the schools expect to provide this supply of able Ph.D.s merely by expanding the proportion of B.S. and B.A. majors who go on through to the doctorate stage of training? And the answer is definitely "No"—as the situation stands at present. Most A.B. graduates are years short of the preparations in basic science and elementary engineering prerequisite to effective graduate study in the geoexploratory fields (paleontology ex-cepted), and similarly many of the annual crop of B.S. graduates lack adequate training in English; in ancient and modern history; and in the modern principles of labor and public relations. Indeed, several basic problems of undergraduate curricular organization and integration remain to be solved before most recipients of a Bachelor's degree will have that sound and broad educational foundation prerequisite to graduate training on a really effective basis. It is for these reasons that we have continued to experiment with our geological engineering program at Princeton, in an endeavor to provide a pilot-plant demonstration of a suitably broad and flexible undergraduate curriculum. Problem 3 But assuming that the schools can and do get undergraduate curricula set up in proper phase and scale to meet needed enrollment quotas for graduate training, what about the most urgent part of our whole mineral-industry educational problem? What about finding and bringing into mineral-industry training those youngsters of superior ability who are, by potential or known inclination, especially well-qualified for geoexploratory work?

Jan 1, 1949

By Eric Jette

THE alloys of gold and iron were investigated in 1907 by Isaac and Tammann,1 who determined the thermal diagram for the entire system by thermal analysis and microscopic examination. They also reviewed the previous literature. Since that time the present authors have been able to find only two additional references. Guertler and Schulze2 examined the electrical resistance of iron alloys containing up to 40 per cent by weight of gold between 0° and 200° C.; the alloys were in the form of wires. The main result of this work was to confirm the solid solubility limit found by Isaac and Tammann; namely, about 20 per cent Au. More recently, Shih3 has examined the magnetic properties of gold alloys containing up to 10 weight per cent iron and particularly the range below 5 per cent. The alloys in the lower range were found to be paramagnetic; the 10 per cent alloy was ferromagnetic. The present investigation was undertaken to determine the solid solubility limits at various temperatures, particularly below the a-y transformation point of iron, since these solubilities are of some impor-tance in connection with the working of the alloys in the manufacture of certain "grey" and "blue" golds.

Jan 1, 1934

By Louis Raymond, John E. Dorn

The object of this investigation was to analyze the recovery that arises when the stress on a specimen undertaking creep is reduced. For this purpose annealed specimens of high-purity aluminum were precrept under a stress of 1000 bsi to a strain of 0.08 following which the stress was reduced for various periods of time to 10, 250, 500, or 700 psi. When the original stress was reapplied the subsequent creep curve lay above that for the unre-covered state and below that for the original annealed state. Analyses on the kinetics of this recovery as a function of the temperature gave a stress-sensitive activation energy that decreased as the reduced stress was increased from a value of 64,000 cal per mole at 10 psi to 37,000 cal per mole at 750 psi. Recovery was also detected and measured during creep under the reduced stress. Following a short initial period, the creep rate under the reduced stress increased monotonically until it reached the secondary-creep rate for the reduced stress. The temperature dependence of this phenomenon was also shown to be correlatable in terms of the previously deduced activation energy for recovery. The activation energies for creep of most pure metals at high temperatures have been shown to agree well with those for self-diffusion.'j2 Since the true secondary stage of creep is usually due to the steady-state balance between the rate of strain hardening and the rate of recovery, it is generally thought that the activation energy for recovery of the creep-induced substructure equals that for creep itself. A shoft time ago, however, Ludemann, Shepard, and Dorn~ found that the activation energy for recovery of the creep-induced substructure in high-purity aluminum under zero stress was almost twice that for self-diffusion, namely about 65,000 cal per mole; obviously recovery under reduced stresses differs in some significant way from the recovery that accompanies the secondary stage of creep. The major purpose of this investigation is to study the effect of stress on the re- covery of the creep-induced substructure in order to provide a better understanding of the recovery mechanism itself. EXPERIMENTAL TECHNIQUE High purity aluminum, containing 0.004 pct Cu, 0.002 pct Fe, and 0.001 pct Si, used in this investigation, was in the form of 0.100-in.-thick sheet which has been cold-rolled to the H-18 temper. Creep specimens were milled from the sheet with their tensile axes in the rolling direction. All specimens were then heated at 686°K for 1 hr followed by air cooling in order to produce an annealed structure which exhibited a uniform equiaxed grain size of about 4 grains per mm. Tests were run in creep machines fitted with Andrade-Chalmers type of lever arms so contoured as to maintain the stress constant to within 0.05 pct of the reported values. Constant temperatures to *O.l°K were obtained by complete immersion of each specimen in a temperature-controlled and agitated bath of molten KN02-KNOs mixture. Where changes in temperature were involved, the change was effected in less than 2 min by manually replacing one bath by another controlled at the second temperature. Displacements over the gage section were sensed by linear differential transformers, the output of which was autographically recorded. The calculated strain measurements were sensitive to 5x EXPERIMENTAL PROCEDURE The following analyses are based on extensions of the previously announced effect of the temperature on the creep strain,2 namely for a = constant, where e = the total true tensile creep strain for a given applied true tensile stress, t = the duration of the test, R = the gas constant, T = the absolute temperature, Q, = the activation energy per mole for creep which is independent of the stress, / = a function of 8, = and of the stress, and a = the stress. The validity of this correlation for high-purity aluminum is demonstrated in Fig. 1 for temperatures in the near vicinity of 600°K; the activation energy for creep, Q,, which is approximately that for self-diffusion, is insensitive to the applied stress

Jan 1, 1964

By N. O. Johnson

The Hog Mountain mine is a pyritic-gold property in the north central part of Tallapoosa County, Alabama, at an elevation of 800 ft. in the southern Appalachian region. It is 13 miles by a good secondary road from Alexander City, a station on the Central of Georgia Railroad. Since its discovery in 1839, the mine has been worked intermittently. The records of past operations are few and are scattered over a long period of time; however, available information indicates a production of approximately 12,000 oz. of gold prior to the present company's activities, which started in 1933. Additional 7844 oz. has been produced under the direction of the present management. The ore from stopes has averaged 0.200 oz. gold per ton; the ore from development, 0.136 oz. gold per ton. Silver, copper, iron and sulphur are also present but to date are of minor importance. The grade of ore in comparatively narrow veins makes necessary extreme vigilance in the methods of mining. Geology Wall Rock.—Hog Mountain consists of a quartz-diorite intrusion approximately 5000 ft. long by 1200 ft. wide. Its resistance to weathering, as compared to the surrounding schists, has led to the formation of a conspicuous ridge rising 400 ft. above the adjacent country. All the mining operations are confined within the limits of this quartz-diorite formation. Except where there is excessive shearing, either parallel or at flat angles to the quartz veins, all the walls of the stopes within the limits of the veins are strong enough to make timbering unnecessary. Where shearing exists, there may be a sloughing off of the walls, especially in the process of drawing the ore. When this occurs, stulls are placed in the stope, either while the stope is advancing, or while ore is being drawn from a completed stope. In general, very little timber is required. Veins.—The quartz veins have been deposited along fracture planes in the quartz diorite. There are 20 principal veins, all of which are roughly parallel and strike at right angles to the long axis of the formation.

Jan 1, 1937

By Walter Barnum

AS a member of the Institute and as the president of the National Coal Association, I come before you today in a dual role. As an Institute mem-ber I welcome the opportunity to make complimentary reference to the growing support which bituminous coal operators are giving to programs looking to the advancement of the engineering profession, and to suggest plans whereby these programs may be enlarged to mutual advantage. As a representative of the bitu-minous industry, it gives me special pleasure to express the appreciation of the industry for the services ren-dered to it by members of your profession. Needless to say, there is a close relationship between the engineer and the coal operator. With increasing frequency and in the interests of the industry, the engineer is becoming more of a factor in the business of producing coal. I need look no further for an out-standing example of this encouraging trend than to Samuel A. Taylor, who not only is a bituminous coal producer but also has risen to such eminence in the engineering profession as to have been chosen the head of this great body of technical men, the American Institute of Mining and Metallurgical Engineers. There are many coal operators whom I might mention as having achieved distinction in the engineering world, such as Howard. N. Eavenson, chairman of the .Coal and Coke Committee. And I would be guilty of a serious .oversight if I failed to make reference to Eckley B. Coxe, one of the founders of the Institute in 1871, a prominent anthracite operator and credited with several important inventions. While it is true that a. considerable number of execu-tives of coal-producing companies in this country came up through the engineering ranks. the proportion of mine executives in England, France, and Germany who are graduate engineers is much larger than it is in the United States. In France all members of the staff are engineers and such is the case in Germany up to the owner of the mine. In Germany the owner is not so frequently an engineer as is the rule in France.

Jan 3, 1927

By B. Bernstrom

A 22-ft diam, 7-ft long, wet autogenous grinding mill was installed in the new Cretaceous plant of the Jones & Laughlin Steel Corp. to prepare crude iron ore for concentration in spirals and flotation cells. The paper describes the flowsheet and gives a description of the operating and metallurgical results that have been obtained. These results include capacity, horsepower, operating problems and a comparison of pilot plant results with those obtained in commercial operation. The Cretaceous plant at the Hill Annex mine of the Jones & Laughlin Steel Corp. was designed with a wet autogenous mill for grinding low grade iron ore so that it could be concentrated by spirals and flotation cells. The plant, on the west end of the Minnesota's Mesabi Range, went into operation in June 1961, and preliminary operating and metallurgical information describing the performance of this mill can now be given. The crude is lean ore from the Cretaceous iron foundation. This formation is a beach deposit of Cretaceous age that overlies the Precambrian direct shipping and concentrating ores. This rock in nature is not extremely hard but is quite resilient, resisting blasting in mining and size reduction in milling. It contains hematite as water-rounded particles and other fragments of the underlying iron formation and adjacent rocks cemented together by a high alumina-silica ferruginous matrix. It is interspersed with hard dense hematite agglomerates and also contains granite pebbles and boulders that were not cleaned off during removal of the surface. It has a 3.48 sp gr and in the stockpile the material consists of frag-

Jan 1, 1962

Jan 1, 1916

By Albert F. J. Bordeaux

The immediate vicinity of the sea-shore, affording special facility for the exportation of ores, makes it possible to work certain mines in the Vladivostok district, which, in more remote places of Siberia., would remain unproductive. Outside of the city of Vladivostok the population is small and the country is very little prospected. Additional discoveries of valuable deposits like the large body of calamine which has recently been opened in the neighborhood of earlier worked lead-silver ores, in the Tetiuhe valley, are still in the field of possibilities. For many years gold alone was produced, in part from the coastal rivers and in part from a quartz-vein on Askold island near Vladivostok. But the production is diminishing, and prospectors are looking for other rivers in the interior, such as the tributaries of the Ussuri. These rivers are now more accessible than formerly, due to the slow but gradual development of colonization by the Russian peasants. The few natives of the country, called Orodjones, are of the Chinese race. They resemble the North American Indian and are hardy fur-hunters. They have given some attention to placers and have already shown good specimens of gold-dust from the rivers Iman, Bikin, Noto, etc. Coal-mining was begun in the Vladivostok region more than 20 years ago, but in a somewhat irregular way. The industry is not as yet important and the best coal-seams are badly prospected, or are even neglected. Copper, lead, and iron exist in several places. The amounts give some encouragement to the anticipation that the discoveries will give rise to important metallurgical works. I here present a review of the various deposits, based upon such safe information as is in hand, when I have not drawn upon my personal observations. Fig. 1 is a map of Eastern Siberia, showing the mineral deposits.

Jan 1, 1913

By T. L. Joseph

A study is made of the amount of solution loss necessary to maintain the reducing power of the gas stream in the blast furnace. Curves are presented to show the effect of solution loss, moisture in the blast, and carbon dioxide from the flux on the nitrogen in the THE blast furnace process is based upon the counter flow of gases and solids. As CO, N, and H, flow upward from the combustion zones, oxygen is acquired from the descending charge. In the reduction of iron ore, a portion of CO is converted to CO, and similarly a portion of H, is converted to water vapor. The inert N,, from the air used in combustion, passes through the furnace with little change. Its concentration is, however, decreased by reactions such as direct reduction and solution loss which increase the volume of CO in the gas stream; Similarly the evolution of C02 from the limestone also dilutes the nitrogen. he purpose of this paper is to illustrate an idealized and simplified method of studying furnace processes by following changes in the gas phase between the tuyeres and the stock line. A more specific objective is to evaluate the effect of solution loss upon the CO/CO, ratio in that region of the furnace in which FeO is reduced to metallic iron. This last stage of reduction requires relatively high CO/CO, ratios to exceed the equilibrium requirements. Solution loss or the reaction of COZ with C to produce CO has a pronounced effect upon the ratio of the carbon gases and is necessary to maintain the reducing power of the gas stream if the consumption of coke is low. It will be explained later that indirect reduction followed by solution loss is stoichiometri-cally equivalent to direct reduction. Calculations will be made to show how the composition of the gas in the region of the mantle varies with coke consumption and with different amounts of solution loss. Such calculations show the condi- tions under which gasification of C with oxygen in the charge is needed to maintain the reducing power of the gas. Equilibrium conditions for FeO and the carbon gases will be used to establish a minimum CO/CO, ratio below which reduction will not proceed. The manner in which carbon is gasified in the furnace, at the tuyeres with oxygen in the air or above the tuyeres with oxygen from the charge, will be a basic feature of all calculations. It is hoped that greater interest in the use of top gas as a means of following furnace reactions will be aroused by the calculations and generalized curves which are presented. Bosh Gas Equations Subject to some alteration by the amount of moisture in the blast and by direct reduction, the gas leaving the combustion zones of a blast furnace has a definite composition. Because a relatively small amount of oxygen is acquired from the charge in the bosh and in the crucible, the products of combustion undergo little change until they enter the shaft. Bosh gas is, therefore, essentially the products of combustion of carbon in a deep fuel bed with air. The relative weights and volumes of reacting materials are expressed by the equation: 2~ + 0? + 3.76N, = 2C0 $ 3.76NZ [I] Air Bosh Gas -air = 79% N? = 3.76) 21% 02 Starting with a known mass of C consumed largely by air, Eq 1, but partly by water vapor, Eq 2, the volume and C + H2O = CO $ H? [21 composition of the bosh gas can be calculated and subsequent changes followed as reactions take place at various elevations in the furnace. As shown in

Jan 1, 1952

By H. C. Fiedler

X HE development of the cube-on edge secondary re-crystallization texture in Si-Fe strip requires that normal grain growth be restrained. It has been shown that the degree of restraint and hence the completeness of secondary recrystallization depends upon the size and number of second-phase particles, which in turn is dependent upon the prior processing history.1y2 The purpose of this note is to show that, for heats in which manganese sulfide particles are providing the restraint to grain growth, the choice of hot rolling temperature depends upon the manganese content. The making and processing of the heats to the final gage of 0.012 in. has been described.3 The compositions are given in Table I. Apparent in Fig. 1 is the decrease in the ability of strips hot-rolled from 1175°C to undergo secondary recrystallization as the manganese content increases. It has been shown that 1175°C is below the solubility temperature of 0.014 pet S in even the 0.038 pct Mn alloy: and the observed behavior is attributed to an increasing fraction of the sulfur forming large manganese sulfide particles at the heating temperature for hot rolling. This fraction of the sulfur is thus unavailable to subsequently form the small, uniformly dispersed particles which are needed to restrain normal grain growth. Since the sulfur is completely in solution at 1325°C,3 strips from all three alloys show strong secondary recrystallization behavior when hot-rolled from that temperature.

Jan 1, 1969

By C. Law McCabe, R. G. Hudson

The Knudsen cell has been employed to determine the free energy of formation of Mn7Cs in the temperature range 800" to 950°C. A value of 66,440 cal was found for hH°o for a-manganese. Measurements of the pressure of manganese over a mixed carbide, (Fe,Mn),C, points to a power relationship between aun7cs and N.4,. RECENTLY Kuo and Perssonl have reported that the carbide of manganese which is in equilibrium with graphite at temperatures up to 1100° C is Mn7Ca. There are no published data on the thermo-dynamic properties of this compound. In order to determine the stability of Mn7Ca, it appeared that, by obtaining the pressure of manganese above 8-manganese and also above Mn,C, in equilibrium with graphite, the free energy of formation of Mn7Ca from 8-manganese and graphite could be obtained. In addition, the vapor pressure of manganese, reported by Kelley From data of Bauer and Brunner,' is subject to some uncertainty and further determinations of the vapor pressure of manganese seemed warranted. In this investigation of the pressure of manganese vapor above pure manganese and also above the carbide of manganese in equilibrium with graphite the apparatus used is the Knudsen orifice cell. The same apparatus, experimental procedure, and method of calculating the pressure was used in this investigation as in one previously reported.~ Care was taken to insure that the cells were at constant weight before using them in a run. The manganese charged in the cell was CP grade powder, carbon free, obtained from the Fisher Scientific Co. A spectroscopic analysis of the manganese after appreciable amounts of it had vaporized from the Knudsen cell showed that no element was present in sufficient quantities to contribute to a weighable weight loss or to decrease the vapor pressure of manganese to any appreciable extent. The spectro-graphic analysis was 0.002 pct Cu, 0.05 pct Fe, 0.002 pct Pb, and 0.002 pct Ni. 8-manganesea is the allo-tropic form of manganese which was present in the cell at temperatures used in this investigation. The manganese carbide, Mn,Ca, was made in the following way: In a closed graphite cell manganese powder was added to graphite powder, which was made from graphite rods for spectrographic use. The manganese powder was the same as that described previously; 5 pct excess graphite was added over that required for the formation of Mn7C,. The mixture was heated in a closed graphite cell for approximately 20 hr at 1350°K under vacuum. X-ray analysis revealed that there was no manganese present after this treatment, but that the lines due to Mn,C, were present. In order to prove that there was no volatile carbide of manganese which was effusing out of the cell, the following experiment was performed: A graphite effusion cell containing graphite power, in excess of that to form Mn,C, of a desired amount, was brought to constant weight on heating at 1228°K. The required amount of manganese was accurately weighed and then added to the graphite effusion cell. The cell was placed in a vacuum at 1228°K for one week, which was the time calculated for the manganese to have effused completely, assuming instantaneous formation of Mn,C8. The cell was then weighed again. This experiment was carried out on two different occasions and both times the weight loss of the cell came within 1 pct of the weight of manganese originally charged minus the weight of manganese left in the cell, as determined by chemical analysis. These data are summarized in Table I. This agreement is considered to be within experimental error and is taken as proof that no carbide of manganese is volatile in this temperature range. It was established, by X-ray analysis, that Mn,C, formed before appreciable amounts of manganese vaporized from the metal powder which was charged. The identification of the carbide of manganese which was present in the Knudsen cell in equilibrium with graphite and manganese vapor was carried out by Kehsin Kuo at the University of Uppsala. He established that the authors' sample, which was submitted to him for analysis, contained the phase

Jan 1, 1958