Search Documents

By W. R. Hibbard

The increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform compatibly regardless of the single crystal crystallo-graphic strain mechanism, complicates this mechanism so as to increase the metal's resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: " Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of dcformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.zl Previous Investigations Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip werc reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elarn4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable yi in. from the boundary. Adcock,6 Yamaguchi,' Seumel, Hirstg and others have also reported this phenomenon as a qualitative trend. Yet attempts by O'Neill'o and Ljunggrenll to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface thc distribution of stresses was so altered

Jan 1, 1949

By Frank F. Aplan

In looking into the crystal-ball scene of minerals beneficiation for 1970 and beyond, an impartial observer becomes con- fused as to what has been done and what is possible in the way of improvements. The mining official must balance the burden which is being shouldered by the mineral industry for maintaining our environment in its pristine state on one hand, with the solid advancements made in technology and cost savings on the other hand. Then the official wonders if this is really the criterion for judging overall performance today. As a prospective engineer, Dave Bolles sees it this way: "Specialization has caused many engineers to subordinate everything to doing their job the cheapest and fastest way. In the future this won't be enough. The engineer in the mineral industry will be responsible not only for mining, concentrating and smelting, but also for the resultant wastes- the mine dumps, the tailing dams and the slag piles." (See Drift on page 63).

Jan 1, 1971

By J. H. Nead

The experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. Conclusions No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability. Composition of Materials An attempt was made to secure steels increasing in carbon by increments of 0.1 per cent. from 0.1 per cent. up to 0.8 per cent., and from that composition to 1.6 per cent. by increments of 0.2 per cent. Actually, however, steels of the composition given in Table I were procured, and as the carbon contents were arranged sufficiently well so that satisfactory curves could be drawn showing the relation between carbon content and other properties, these steels were used in the experiments.

Jan 1, 1916

By W. F. Boericke, T. H. Garnett

The Wisconsin zinc district, or the Upper Mississippi lead and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies country in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, withroads, railways, streams, and the various towns, or "camps," around which the mines are clustered. The hatchwork indicates the areas in which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zoncs of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. ease or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within comparatively recent time been worked intensively for zinc, the chances are good for opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However; the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Ben-ton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland. The district is one of the best farming districts in Wisconsin, with deep fertile soil. The farms are large and well improved, and the towns are modern and prosperous. Railroad facilities are good and proximity to Chicago is an asset. Mining is usually done on a leasing system of 10

Jan 1, 1920

By W. Geo. Waring

Introduction THE winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district, presents, few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend in no small measure the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are, really continuations of the Joplin district, the total value of ores produced reached the sums of $34,089,503, and that of the metals, $58,927,941.1 The ores produced in the Joplin district are remarkable on account of their almost uniformly high" metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless clue to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proven beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to he exhausted in time, for ordinary mining purposes, acid it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 9, 1917

By Reinhardt Thiessen

UNDER sulfur in coal, is usually understood that form of sulfur which is combined with iron and known as pyrite. It occurs in the form of halls, lenses, nodules, continuous layers, thin sheets, or flakes, both in horizontal planes and vertical cleavage fissures. But pyrites also occur as very fine microscopic particles, or nodules, disseminated through the compact coal. This form has had but very little consideration. Finally, there is sulfur in coal in an amicroscopic form (not visible with an ordinary microscope), probably combined with the organic matter that exists -in tile coal. This form has had considerable attention from a scientific standpoint, but has probably not been recognized enough on the economic side. One or the other, or both, of these two latter forms may comprise the larger part of the sulfur content of coal, especially after it has been washed or otherwise prepared for use.

Jan 9, 1919

By Robert Lewis

THE Utah coal field to which the name Book Cliffs is applied runs in a northeast direction from Mt. Hilgarde, in Sevier county, along the escarpment of the Wasatch Plateau to the vicinity of Castle Gate, thence southeast along the Book cliffs, which lie to the north of and generally within sight of the Denver & Rio Grande Railroad,. to the Colorado line. The Book cliffs form the southern escarpment of the West and East Travaputs Plateaus, and vary in height from 2,000 to 6,000 ft. At the base of the Wasatch and Book Cliffs escarpments is a broad plain known as Castle valley. The coal beds outcropping in the escarpments along this valley are worked on the largest scale of any in the State, and this particular area is known locally as the Castle Valley coal field. Geology The Book cliffs are capped by the Tertiary-Eocene-formation, consisting of varicolored shales; buff sandstone, conglomerate, and subordinate thin beds of limestone. Different sections show diverse stratigraphy. This is mainly the Wasatch formation, and lies unconformably upon the rocks of the Upper Cretaceous. Fig. 1 is a generalized section of the rocks of the. Book Cliffs field. The Mesaverde formation contains the cliff-making rocks of the Book cliffs, and is composed of massive sandstone interbedded with sandy shales and beds of coal and carbonaceous shale. The sandstone has greater resistance to erosion and the formation is characterized by escarpment ledges and cliffs. The shale is commonly sandy and is drab in color, but where it is associated with the coal it is usually carbonaceous. The sandstone is generally buff, though occasionally it is white, and in places red. The bedding ranges from thin to massive. In the lower part. of the formation the sandstone is red in

Jan 7, 1914

By F. Weinberg

It has been suggested, for some time, that the behavior of metals under high-temperature creep conditions is strongly influenced by the behavior of the grain boundaries present in the material. This has led to a number of investigations1-6 in which attempts were made to measure the properties of the grain boundaries themselves, both to determine their contribution to the creep process and to obtain further knowledge of their intrinsic structure and properties. The present investigation was undertaken to extend the observed data under more closely controlled experimental conditions and to attempt to clarify sonie of the discrepancies in the literature. A brief report of the preliminary results has been published.7 EXPERIMENTAL PROCEDURE For the present investigation, controlled orientation specimens were used having plane boundaries which terminated at the specimen surface. Trierys-tal specimens were used instead of the bicrystal type of Puttick and King,' in order to simplify the gripping technique required to apply a shear stress along the boundary. The aluminum used was obtained from the Aluminum Francaise and was of 99.994 pct purity, containing 0.002 pct each of Cu, Fe, and Si. The aluminum tricrystals were grown horizontally from the melt, in graphite boats, and in an argon atmosphere, following the technique developed by Chalmers.' The orientation of the tricrystals was controlled by using seed crystals separated by mica inserts. Thermal conditions were adjusted to produce tricrystals having boundaries which were macroscopically straight, parallel to the growth direction, and perpendicular to the top surface. Following growth, the tricrystals were carefully cut with a jeweller's saw to the test specimen shapes shown in Fig. l(a) and l(b). In Fig. 1(a), the boundaries subjected to shear stresses are indicated AB and CD: Points A and C are the ends of the mica inserts separating the seed crystals; points B and D are at lateral cuts made in the specimen. It was found that the slots left by the mica inserts at A and C had to be enlarged slightly, by cutting, to ensure that the boundary terminated freely at these points. A shear stress was applied to the boundarks by gripping the upper two legs in file-faced Inconel grips and suspending a weight from the lower part of the specimen held in similar grips, as shown schematically in the diagram. The test specimens shown in Fig. 1(b) were cut from long

Jan 1, 1959

By J. S. Ross

Few Canadians realize the role of their domestic industrial minerals industry because it is over-shadowed in production value by a large metallic minerals industry. But since 1960, Canada has had a reasonably well balanced, mature industrial minerals industry; and although the nation's sparsely scattered population has not been able to support an industrial minerals industry in a manner comparable to the domestic and foreign support given the metal mining sector, Canada is, nevertheless, exporting large quantities of higher priced nonmetallic minerals. Production of many of the basic minerals had been firmly established long before 1960, but it was not until the late 1950's that the output of cement, salt, titanium dioxide pigment and slag, sulfur, gypsum and sodium sulfate reached relatively high levels. Shortly after 1960, the significant potash and lithium chemicals industries were established and their effect is just now being realized.

Jan 11, 1964

By W. B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 1, 1961

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

NEW MEMBERS The following list comprises the names of those persons who became. members during the period Sept. 10, 1918, to Oct. 10, 1918. ADDISON, HERBERT, Vice-pres. and Mgr., Big Horn Collieries Co., 412 Colorado Bldg., Denver, Colo. ALLAN, .ANDREW, JR A. Allan & Son, Harrison, N. J. AMI, HENRY M., Charge of War Metals and Minerals, British Embassy, Washington, D. C. ALTHAR, HOMER C., Mill. Engr., The Lorain Coal & Dock Co., Bridgeport, Belmont Co., Ohio. BASER, JOHN T Pres., J. T. Baker Chemical Co., Phillipsburg, N. J. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., 2301 Connecticut Ave., Washington, D. C. BENSON, JOHN PATS Min. Engr., Aurora Cons. Mines Co., Aurora, Nev., BOSWELL, H. F Resident Inspector, Southern Railway System, St. Louis, Mo. BRAUCHER, PETERS., Foundry Mgr., Philadelphia & Reading Ry. Co., Sixth & Perry St., Reading, Pa.

Jan 11, 1918

By Francis C. Krauskopf, Carl E. Swartz

Metallurgists differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a 1-mm. screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in color, having the general characteristics of a spinel. Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution, zinc values tied up in this compound remain behind History In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite; others merely a mixture of zinc and iron compounds. As early as 1851, Pelouze(')' prepared calcium ferrite by fusion of calcium oxide and ferric oxide. Ebelman, 2) about the same time, prepared

Jan 1, 1928

By J. C. Mertz

ACCURATE knowledge of the solid solubilities of the elements that dissolve in the important base metals is needed for guidance in the preparation and heat-treatment of the alloys derived from these compo-nents. While there is still difference of opinion concerning the merits of the X-ray and microscopic methods of determining such solubilities, it is certainly true that the recent extensive use of X-ray diffraction to review the existing constitutional data has revealed many glaring inaccu-racies and has brought about a much improved knowledge of phase-boundary locations, which will inevitably come to include all of the important alloy systems. When the work is done with all necessary precautions it appears that in the majority of cases where the solubilities extend beyond a few tenths of a per cent the X-ray back-reflection technique is capable of furnishing the best of information in this field. For the most prolonged and thorough studies it is obviously advisable to combine the results of several methods, in particular, to obtain an agreement between X-ray and microscopic data. This paper reviews the work previously done on the solubilities of phosphorus, arsenic, antimony and bismuth in copper and, in considera-tion of the uncertainties thus made apparent, presents, new X-ray data obtained with the first three members of this group.

Jan 1, 1936

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

[A Aall, Christian H., M49 D Mgr, American Metal Climax, Inc., 61 Broadway, New York 6, N.Y. Aaroe, S. L., A54 B Sales Mgr, The W. S. Tyler Co. of Can. Ltd., St. Catharines, Ont., Canada Abalos, Teodulo Q., J57 A Foreman, Lepanto Cons. Ming. Co., Mt. Province, Philippines Abbass, G., M55 P. O. Box 680, Hong Kong, China . Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abdullah, M. Y., J53 Dept. of Mines Res. Div., P. O. Box 1016, Tiger Lane, Ipoh Perak, Malaya Able, John F., Jr., J53 A Ming Engr, USA SIPRE 1215 Washington Ave., Wilmette, Ill. Abell, Leo M., M31 B Conct Supt, Phelps Dodge Corp., Morenci, Ariz. Abenius, Hakan Wilhelm, M52 A Mng Dir, Stora Kopparbergs Bergslags AB, Falun, Sweden Abenoroth, Harry F., A57 Natl. Carbon India Ltd., 18A Brabourne Rd., Box 217, Calcutta, India Abercrombie, Harry W., J56 1645 Camphor Dr., Lakeland, Fla.]

Jan 1, 1961

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel'd and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By Keijiro Nishio

At a time of great antiquity when our Yomato tribe had not yet found its way throughout the country, there lived in Japan barbarous tribes of the stone age, whose dwellings were vertical caves covered with roof's of twigs and weeds. In a cave lately discovered at the village of Morita, 10 miles west from the port of Aomori, there were found pieces of micaceous iron-ore and psilomelane, with oval holes pierced from both sides. Apparently these objects were regarded as ornaments or curios, without being applied to any practical use. Among the traditions given in the Nihonshoki, an ancient history of Japan, there is one relating to the mining industry. According to this tradition, in the mythological age Izanami-no-Mikoto gave birth to Kanayamahiko-no-Mikoto, god of mines, and Amaterasu-Okami (the sun-goddess) was armed with swords. It came to pass at one time that she concealed herself in Ama-no-Iwato ("Heavenly Cave"), and several gods made contrivances to entice her out. Among them, Ishikori-dome, a smith, made a mirror with copper obtained from the Ama-no-Kagoyama, by means of a pair of bellows known as the Ama-no-habuki, which was made of a deer-skin. It is recorded also that Susanb-no-Mikoto, her younger brother, observed the abundance of gold and silver in Korea, where his descendants were to reign, and urged them to provide themselves with boats to convey them across the Sea of Japan. In the course of time he accomplished his object, proceeding to Korea with his son, Isotakeru-no-Mikoto. These accounts

Jan 1, 1913