Search Documents

By F. C. Blickensderfer

DURING 1914 and 1915 extensive experiments were conducted at the concentrator of The Detroit Copper Mining Co. of Arizona, at Morenci, Ariz., in order to test the relative grinding efficiencies of the Marathon, the Chilean and the Hardinge Mills. The Marathon mill used in the experiments was the first one ever built by the manufacturers; and since this was the first time that it was given a thorough tryout, with such remarkable results, the data have been, assembled in the following paper and submitted in the interests of the milling profession.

Jan 8, 1916

By Lincoln F. Elkins

The Spraberry Trend Field of West Texas was discovered in January, 1949. Drilling of 2.234 wells and production of some 45 million bbl of oil by January, 1953, indicated this to be an important field which will ultimately cover more than 400,000 acres. In addition to being the world's largest field in areal extent, the Spraberry has presented many problems in well completion and operation and has demonstrated unique reservoir performance characteristics. The pay section consists primarily of a few fine grained sandstone or siltstone members in a thousand-ft thick section of shale, limestone. and siltstone. Since porosity averages only 10 per cent and nearly all permeabilities are less than 1 md, conventional core analysis does not delineate the "pay" section. Mercury injection was used as a capillary pressure test adaptable to rapid routine use to select those intervals having low enough connate water saturation to contain commercially significant oil saturation. In the central area of the field this "pay" amounts to 16 ft of Upper Spraberry and 15 ft of Lower Spraberry sands. An interconnected system of vertical fractures, observed in cores, provides the flow channels for oil to drain into the wells hut most of the oil is stored in the matrix since the void volume of fractures is estimated to be less than 1 per cent of that in the sand. Initial potentials of wells range up to 1.000 B/D after fracture treatment which should be compared with estimated capacity of 5 to 10 B/D if oil had to flow into the wells through the sand itself. Without exception initial pressures of later drilled wells were significantly lower than initial pressures of earlier drilled nearby wells in a large area some 6 miles long. This means the earlier drilled wells had drained fluids from areas much greater than their 40-acre proration units. Since most of this performance occurred while the reservoir pressure was above the. saturation pressure it was analyzed by the compressible fluid flow theory. This analysis gave calculated initial presrilres which agreed within 30 psi of measured pressures of 60 per cent of wells in the area using 16-md permeabilitv corresponding to a fracture system substantially that indicated by cores and using combined compressibility of rock and its contained oil and water corresponding to the core analysis data. The most important feature of this analysis was the very close agreement between effective compressibility of the rock and its contained oil and water from the field performance and that from the core tests, because it meant there are no "islands" of low permeability reservoir rock left untapped in the inter-well area and thus no additional wells are necessary to insure that at least one well penetrates each "reservoir." Twenty-five of forty-four 40-acre spaced wells on three contiguous sections were wed in a four-month inteference test. Six shut-in well. were tested monthly for oil production. productivity index. gas-oil ratio and pressure buildup, and seven shut-in wells were tested for decline in reservoir pressure. Tests on 12 regularly producing wells gave comparative data for interpretation of shut-in test wells. Reduction in reservoir pressure, decline in productivity index. and increase in gas-oil ratio were found to be substantially the same in the shut-in test wells as those in the comparative regularly producing wells, meaning that the producing wells were depleting the

Jan 1, 1953

By W. F. Cloud

The data and information compiled under Part I of this report are the results of experiments performed in the petroleum engineering laboratory under the supervision of W. F. Cloud, Associate Professor of Petroleum Engineering and William Schriever, Professor of Physics, University of Oklahoma. Problems Being Studied Most of the time has been spent in trying to determine the rate of flow and pressure gradient in a 4-in. flow tube 10 ft. long, which was packed with sand of various grain sizes. To date, only two kinds of sand have been packed in this tube: 60 to 80-mesh Canadian river sand, 60 to 80-mesh and 80 to 100-mesh Simpson sand. The original intention was to follow the same procedure and use the same types of crude under identical saturation pressures of both air and gas, as well as unsaturated (dead) oil, flowing the various crudes through several different sizes of both Canadian river and Simpson (Wilcox) sands, but lack of time has prevented such an intensive study of the problem. Some additional time has been spent flowing saturated and unsaturated crudes, similar to those used in the 4-in. tube, through 1-in. tubes, one of which was 2 ft. long and one 5 ft. long. The results obtained have been checked against those obtained by using the 4-in. tube, to obtain the relation of diameter and length of tube to rate of flow in similar sands. Laboratory Equipment Saturation Tank.—A heavy steel cylindrical saturation tank, capacity about 42 gal. was mounted on a platform of bricks, then a galvanized tin temperature bath was built around the saturation tank. This contained

Jan 1, 1930

By Heinrich Freyn

THE American iron and steel manufacturer finds himself to-clay barely at the threshold of enormous possibilities for practicing rational economy in the use of fuels. The fuel cost is by no means the smallest of items which enter into the cost of manufacture of iron and steel products, but the great wealth of this country in high-grade fuels, together with a protective tariff, has heretofore made fuel economy relatively unimportant. In Germany, the use of raw coal for the purposes of iron and steel manufacture has been all but abandoned and large sums of money, formerly irrevocably wasted, are now being saved. When scanning the literature of this country devoted to the application of gas power, but little information will be found on a subject which, however, is destined to become of considerable importance in the United States, namely, the use of coke-oven gas for the generation of power in gas engines. This lack of information can be traced to the fact that the regenerative by-product coke oven with its large amount of surplus gas is still far from having attained in this country the universal application which it has found in Europe. This statement needs hardy any corroboration other than the evidence of statistical investigations made by E. W. Parker of the United States Geological Survey, according to which only approximately 25 per cent. of the total coke produced in this country in 1912 was made in by-product coke ovens, whereas 75 per cent. was produced in bee-hive ovens. This entailed the enormous loss of over $80,000,000 in non-recovered by-products, such as gas, tar, and ammonia, without considering the substantial loss due to the non-recovery of benzol from the coal. There are two more or less distinct fields of application of the by-product coke oven: one, to furnish as the main product metallurgical coke of specified quality, and surplus coke-oven gas as the by-product, and the other, to carbonize high-volatile coals, and thus produce as the main product large quantities of gas, high in heat value and rich in illuminants, adapted primarily for domestic heating and lighting, while domestic coke becomes the by-product.

Jan 4, 1914

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production ; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By Leon H. Nelson

Several factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in, square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation. Pouring Temperature The temperature (or, more correctly, the amount of superheat above the liquidus-solidus) of the steel entering the ingot is, of course, one of the most important factors influencing segregation and solidification. Table 1 gives the average segregation of a number of heats of S.A.E. 1040 steel with normal pouring temperatures of 2775" to 2825" F. The table also gives some data on segregation in hot heats (pouring temperature 2840" to 2870" F.) and in cold heats with some skull (poured at 2725" to 2760" F.). The results in Table 1 are on steel ingots with 20-in. square cross section and 60 in. long to the hot top. The ingot weighs 7100 lb. and the hot top contains 14.3 per cent of the total ingot volume and 11.2 per cent of the total ingot weight. The results are from drillings after rolling the ingots to bloom size. Segregation results obtained on the bloom are probably not as great as they would be in the ingot itself, since heating the ingots for rolling can perhaps cause some migration of carbon from regions of high and low carbon to those of average carbon content.

Jan 1, 1937

By Plato Malozemoff, A. M. Gaudin

IN modern practice the major portion of an ore is reduced to flotation size by fine grinding. As the result of grinding fine enough to liberate most of the minerals, a substantial portion (generally 5 to 15 per cent) of the ore is inadvertently reduced to a size much finer than that necessary for liberation. This portion of most flotation pulps is very refractory to recovery by flotation. A reduction of one-quarter or more in recovery in this range of extremely fine particles can be observed. The loss in metals caused by overgrinding is appreciable. That this loss is characteristic of very fine particles has been suspected for some time;(l)† however, it was definitely quantified only recently.(2) Definite reduction in float-ability with reduction in particle size beyond a critical size of maximum floatability can be accepted now as an established fact. Formulating the Hypothesis In looking for the cause of the ill behavior of the finest particles it may be well to consider the essential differences between fine and coarse particles. A difference that immediately comes to mind is their intrinsic difference in size and consequently in relative extent of surface. If one agrees that attachment of mineral particles to bubbles must follow direct encounter of particles with bubbles one is forced to conclude(3) that the probability of encounter between a mineral particle and a bubble varies directly as the size of the particle, provided the particle is small compared to the bubble. In other words, the finer the particle the poorer its chance of being recovered in a given time of flotation. There is an effect, implicit in this theory, which should overcome the effect of excessive fineness of the particles; namely, flocculation of the particles. The floccules can be conceived as being simply larger particles and therefore capable of becoming attached to bubbles. And, indeed, in all the cases in which a sulfide mineral of near-colloidal size was successfully floated the mineral (but not necessarily the gangue) was flocculated. Moreover, it was shown experimentally(4) that galena previously flocculated by inorganic flocculators and then added to gangue

Jan 1, 1935

By Willard L. Cumings, Benjamin L. Miller

The Camaguey brown iron-ore deposit covers the top of Sari Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name " San Belipe district" is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,' who says: " The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camagueg City, in the province of Camagueg.....Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements .as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp2 has the following to say of ores in Camaguey Province:

Jan 1, 1912

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1753 from the Kanawha licks. Practically all this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the white man, Indians are known to have made salt from salt springs such as those that existed at Avery Island, LA, Charleston, WV, Saltville, VA, and Onondaga, NY. In 1862 the first rock salt was mined in the US from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, VA and then at Retsof, NY in 1885. Of the more than 39 million tons produced annually in the United States, about 58% or 23 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc. Utilization of cavities created in salt beds and domes has grown rapidly since 1947 until now the waste salt is creating an ecological problem. The uses for both dry- and solution-mined cavities range from the storage of liquid hydrocarbons to containerized storage of toxic wastes, from compressed air for the peak shaving of power to storage of nuclear wastes. Geology Mineralogy Properties: Because of its simple structure, halite, the mineralogical name for salt, was the first structure to be analyzed by X-rays. It has the following properties: Formula: NaCl (Na-39.34%. Cl2-60.66% ) Crystallography: isometric, hexoctahedral, 4/m 32/m Space group: Fm3m A0: 5.627 kX Cell contents: Na4CI4 Habit: usually cubic, rarely octahedral, massive, granular to compact Physical properties: Refractive index: 1.554 Twinning: observed on {111} Cleavage: {001} perfect Fracture: conchoidal, brittle

Jan 1, 1983

By R. H. Goodrich

Development in this district during the year 1929 was little different from that of any other year despite the somewhat depressed condition of the oil business in general. The year was marked by: (1) An intensive geophysical campaign in the search of deep-seated salt domes; (2) the rather successful exploration and development of lateral sand production on the flanks of some of the older domes. Geophysical Exploration Geophysical work is confined almost exclusively to the torsion balance and seismograph. At the beginning of the year there were approximately 185 individual instruments of all types engaged in the search of structures in the Gulf Coast of Texas and Louisiana. This total includes 3 magnetometers, 83 torsion balances and 100 seismographs. The number of parties operating the torsion balances was 47; seismographs, 20; magnetometers, 3. It is estimated that 4,800,000 lb. of dynamite or other explosives were used in seismic exploration. During the year the torsion balance and seismograph were credited with having discovered the following salt domes: Texas, Danbury dome, Brazoria County, H. & T. B. R. Co., and Clodine dome, Fort Bend County, John Fredricks and Wm. Stanley, Satowsky Survey; Louisiana, Iowa dome, Calcasieu and Jefferson Davis Parishes, T. 9 S., R. 6 and 7 W., and Cameron-Meadow dome, Cameron Parish, T. 14 S., R. 13 W. Because of the secrecy maintained in these developments, it is somewhat hazardous to venture opinion as to the number of salt domes found during one year. The discovery of gas at Mykawa district and at Genoa district, in Harris County, Texas, is considered of more than passing importance, because there is indication in the performance of these two districts that commercial accumulation of oil and gas may be found in the Gulf Coast on structures other than the wore or less definite salt dome type. While it is generally conceded that the accompanying structure in these instances are deeply buried salt domes, it is a fact that neither the seismograph nor the drill have indicated the presence of salt.

Jan 1, 1930

Jan 1, 1904

By C. H. Johnson

THE year 1952 has seen the continuance of the trend pointed out by Tell Ertl in this magazine a year ago, toward mechanization in metal and mineral mines. Outstanding progress has been made in the adoption of rock bolting in situations where, a short time ago it would have seemed inapplicable. New devices, better equipment, and improved practices are in part responsible for shifting fashions in mine development, stoping methods, and transportation systems. Only new mines, of course, can take the advantage of the new ideas that are being tested and demonstrated throughout the industry, but the old mines often show a surprising adaptability

Jan 2, 1953

By C. E. Sims, C. A. Zapffe

MANY hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel,105 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlement is due to hydride formation does not conform to the known facts.104 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel. A second widely discussed hydrogen-caused defect is the "flake" or "shatter crack." Although it is generally agreed that the presence of hydrogen is a prerequisite for their appearance, it is also realized that internal stress plays a decisive part. The relationship of hydrogen to internal stress has not been explained very clearly; nor is it always clear what the relationship is between a "flake" and a "snowflake," or between a "fish eye" and a "shatter crack." More importantly, the relationships among hydrogen embrittlement, hydrogen-caused fissures such as "flakes" and the ultramicroscopic structure of steel have scarcely been recognized. The present investigation attempts to provide an explanation for the embrittlement of steel by hydrogen by showing cause for accepting the "block" concept of metal crystals, and then to show how the numerous hydrogen-caused defects are interrelated in the light of this concept. EVIDENCE OF SUBSTRUCTURE IN METAL CRYSTALS It appears that the concept of a crystal as an aggregate of smaller multi-atom units must be accepted in some form if the behavior of metals is to be understood. The abundant literature on the evidence of an ultramicroscopic "mosaic" structure in metals and other crystalline substances suggests that the physicist has provided the metallurgist with an invaluable new insight. The exact picturization that any one physicist provides may be open to question, but the fact that there is some such fundamental substructure seems undeniable. The present work makes no pretense of comprehensively treating the imperfection structure theories. Nor will conclusions be drawn here regarding the exact nature of the substructure of crystals. However, the acceptance of some imperfection theory of fundamental attributes seems so necessary to an understanding of the behavior of hydrogen in steel that the following brief

Jan 1, 1941

By Victor deWolfe

INTRODUCTION The Henderson Mine, located near Empire, Colorado, utilizes a continuous panel caving system to extract ore as one of the world's major producers of molybdenum. Any mine using a caving-by-gravity technique of mining must rely on closely controlled draw of the caved ore. This control is essential to insure proper caving action, to avoid damaging load concentrations of weight and to minimize the dilution of ore with waste material. Henderson is no exception. Draw control is a major factor in all production planning, from long- range plans to short-range and day-to-day ore scheduling. Draw control is reviewed constantly and administered daily in an effort to optimize production efficiency, ore recovery, and cave management. MINING METHOD The cave at Henderson is massive, moving slowly through large panels that are 244 m (800 ft.) wide by 610 m (2,000 ft.) long. Generally two cave areas are drawn at one time. The areas under active draw vary in size but can be as large as 244 m (800 ft.) by 244 m (800 ft. ) containing 400 draw points. Each draw point contains 45,360 mt (50,000 st) on the average and takes about two and one half years to exhaust. A complete panel is worked for seven to ten years. No pillar exists between panels, but rather a buffer zone of broken ore, or "static face," is left in each panel to be drawn with the adjacent, yet-to-be-caved panel in efforts of minimizing dilution of a working area from an exhausted one. (Figure 1) Production drifts are driven on 24.4 m (80 ft.) centers through the ore body. Between the production drifts are funnel-shaped draw bells on 12.2 m (40 ft.) x 24.4 m (80 ft.) centers to receive ore from the cave. Each bell is accessed by two draw points, one from the production drift on either side, thus forming a 12.2 m (40 ft.) x 12.2 m (40 ft.) draw pattern. Extraction of the ore is by rubber-tired, 3.8 m3 (5 yd3) load-haul-dump equipment. The LHDs then tram the ore a maximum of 49 m (160 ft.) to ore passes. Cave initiation and bell development are done from the undercut drifts which are parallel to and 17 m (55 ft.) directly above the production drifts. Longhole rings are drilled and blasted from the undercut drifts to define the bells and establish the undercut for caving. (Figure 2) DRAW CONTROL Since the cave line at Henderson is constantly advancing, it is necessary to be continually initiating new cave at one end while exhausting it at the opposite end. There must exist, therefore, an angle on the ore-waste contact in the broken rock from initiation to exhaustion. The basic concept of draw control is to keep this angle as smooth and even as possible, particularly at the time of exhaustion. If this is achieved, draw points are exhausted more or less in a line, avoiding pockets of remaining ore surrounded by exhausted areas. These pockets would cause spotty ore extraction at the time of exhaustion, increasing the amount of dilution occurring while introducing the potential for significant weight problems in the production area. To arrive at the desired angle on the ore- waste contact, maximum tonnage percentages are assigned to each row of draw points increasing at 10% or 15% increments (depending on cave size and velocity of draw) working away from the cave line. The available tonnage indicated by these percentages is the maximum allowable tonnage to be extracted from each draw point until the available tonnage percent- age is increased. As the cave moves, these percentages increase for each draw point regularly. However, in general the tonnage drawn from each draw point is kept at about 50% of this allowable maximum in order to maintain adequate available tonnage in the cave to sustain production for seven months if cave initiation were to cease. This available tonnage cushion is a safeguard built into the draw control program at Henderson to accommodate fluctuations in the rate of cave advance. When draw points move past the row of 100% tonnage availability, they are drawn past the desired 50% at the same increments per row until exhausted. (Figure 3) To achieve proper draw control, the number of LHD buckets to be taken from each draw point is assigned daily. The actual buckets taken, which may at times deviate from the

Jan 1, 1981

By E. W. Johnson, M. L. Hill

Cold working of iron-carbon alloys was found to increase greatly the hydrogen solubility and to decrease the diffusivity at temperatures up to 400° C. These effects are increasing functions of both the carbon content and the degree of deformation. The hydrogen behavior is consistent with the idea that cotd working creates "traps", which are concluded to be microcracks in which the hydrogen is chemisorbed. Hydrogen embrittlement is explained by the Petch theory of metal crack surface energy loss due to hydrogen adsorption. HYDROGEN embrittlement of steel has been studied for many years and has been the subject of an extensive literature, but the mechanism of the effect has not been completely understood. The embrittlement is unusual in that the ductility loss is not accompanied by an increase of the yield strength, being primarily a decrease of the fracture strength alone. The loss of fracture strength is usually most severe in the temperature range between 0°and 100°C. Here the solubility of hydrogen in the iron lattice at ordinary H2 pressures is extremely low while the diffusivity is still quite high. From the relationships between the ductility and the hydrogen content, test temperature and strain rate, it is apparent that the hydrogen atoms causing the ductility loss difbse to and concentrate in small regions of the metal which are especially susceptible to the initiation and propagation of fracture. This hydrogen segregation apparently occurs after plastic straining has begun. Below 0°C the ductility loss persists only at low strain rates in confirmation of the view that the embrittlement is diffusion .controlled. The tendency of the embrittlement to disappear above 100°C can be explained by the increasing lattice solubility of hydrogen with rising temperature. A common view of hydrogen embrittlement of steel is that the hydrogen initially dissolved in the metal lattice diffuses to structural discontinuities and there precipitates as H2 gas at very high pressures which assist the external stress in causing premature failure.1,2 The idea of a high H2 pressure in equilibrium with ordinary amounts of hydrogen in steel at room temperature is due to observations of hydrogen behavior in fully annealed material, for which the Sieverts' law constant relating solute concentration to H2 pressure is extremely small. Hydrogen-embrittled steel, however, is always plastically deformed to some extent, and therefore it is important that hydrogen embrittlement be explained primarily in terms of hydrogen behavior in plastically deformed material. Such an explanation is attempted in this paper. Previous studies of hydrogen in cold-worked steel have shown that both the solubility and the diffusion rate are significantly chaned when the steel is cold worked. Darken and Smith discovered that the amount of hydrogen absorbed from acid by cold-rolled steel at 35°C is many times greater than that absorbed by hot-rolled steel. They found also that the hydrogen permeability of the steel is unaffected by cold working. Keeler and Davis4 confirmed the high apparent solubility of hydrogen in cold-worked iron-carbon alloys at temperatures up to and even beyond the recrystallization temperature. They also found that this solubility increase accompanying cold work is a sensitive function of the carbon content, being absent when no carbon is present. The present experimental study was undertaken primarily to obtain an improved understanding of the behavior of hydrogen in cold-worked steel. Data were obtained on the effects of temperature, H, pressure, carbon content, and degree of cold work on the hydrogen solubility and diffusivity in iron-carbon alloys. These data have been helpful in elucidating the nature of the cold-worked steel structure as well as in providing information on the mechanism of hydrogen embrittlement of steel. EXPERIMENTAL Cylindrical specimens for hydrogen absorption and diffusion rate measurements were prepared from three iron-carbon binary alloys and a commercial SAE 1010 steel. The iron-carbon alloys were prepared by vacuum melting electrolytic iron with graphite in a magnesia crucible. The alloys were cast in vacuum as 2 1/2-in. sq ingots weighing about 20 lb each. The ingots were hot rolled (above 1900°F) to 5/8-in.-diam round bars and then cooled in air to room temperature. The resulting metallographic structure consisted of islands of fine pearlite surrounded by free ferrite. Chemical analyses of the materials are given in Table I. The 5/8-in. diam bars were turned to diameters such that cold reduction to the desired final specimen diameters would result in either 30 or 60 pct reduction in area (RA). The machined bars were then cold worked by swaging at room temperature

Jan 1, 1960

Jan 1, 1906

By Jerome J. English, Gordon W. Powell

An experimental investigation and mathematical analysis of the thermal-dilation behavior of the titanium alloy Ti-7Al-3Cb have shown that the linear dimensional changes associated with the polymorphic transformation need not be isotropic. The absolute magnitude of the linear dimensional change, which may be either positiue or negative, associated with the cr-p transformation is dependent upon the relutzve volumes of different orientations of the transformation product. It is hypothesized that the dilation irregulati-ties that have been observed during the polymorphic transformation of pure, coarse-grained titanium and other titanium-base alloys can be explained in the same manner. When titanium is heated above about 165O°F, the hcp a structure transforms to bcc 0. Thermal-dilatioh measurements have shown that the transformation is accompanied by a decrease in length of 0.16 pct.' Such dilation behavior would be expected because the volume of the hcp unit cell is about 0.3 to 0.4 pct greater than that of the bcc unit cell. A recent investigation2 of the thermal-dilation behavior of an experimental a-p* titanium alloy, Ti- 7A1-3Cb, containing 0.06 wt pct 0 showed that its dilation behavior during the polymorphic transformation differed substantially from that reported for unalloyed titanium. The first time the alloy was cycled through the transformation, the dilation curve closely duplicated that of unalloyed titanium. However, upon repeated cycling through the transformation temperature range, both the magnitude and the sign of the dimensional change associated with the transformation were observed to vary with each cycle. This investigation was undertaken to obtain additional data on the dimensional changes associated with the polymorphic transformation in the Ti-7A1-3Cb alloy and to determine the cause of the dimensional irregularities. After testing, the specimens were examined metallo-graphically. In addition, Laue back-reflection patterns were obtained from selected sections taken perpendicular to the specimen axes to determine the a orientations present in these sections. White radiation from a tungsten target and a 0.1-mm-diam collimator were used to produce the diffraction patterns. RESULTS Dilation Curves. Three types of thermal-dilation curves were obtained when the a-8 titanium alloy was heated and cooled through the transformation temperature range. These three types of curves are illustrated in Fig. 1. The type I curve represents what is considered normal behavior, because the dilation change is what would be expected on the basis of the volumes of the unit cells of a and p. The Type I1 curve is the inverse of Type I. Normal behavior is characterized by an expansion on cooling through the transformation, whereas a contraction takes place in the Type 11 curve. With Type ni behavior, no clearly distinguishable length change occurs during the transformation. No other anomalies that might be indicative of other phase transformations were observed in the dilation curves at lower temperatures. Apparently, the cooling rate was low enough for equilibrium to be reached during the 0 to a transformation. Table I lists the types of dilation curves observed during the polymorphic transformation as a function of the direction of measurement and cycle number. The A1 value was determined by extrapolating the low-temperature (a + 5 pct p) and high-temperature (100 pct p) segments of the dilation curves to a common temperature and measuring the difference in the or-dinates at that temperature, see Fig. 1. The transformation occurs over a temperature range in this alloy, so the magnitude of A1 is not an absolute value but depends on the choice of temperature. A mean temperature, T,, within the transformation temperature range was selected for the measurement. T, on cooling occurred about 100°C lower than T, on heating. The first time each of the three dilation specimens was heated to above the temperature, that is, Cycle 2, normal Type I behavior was observed. In Cycle 3, two deviations from normal behavior occurred. First, during cooling of the longitudinal specimen, a substantially larger expansion, +0.21 pct, was measured as 0 transformed to a compared with +0.03 pct in Cycle 2. Second, the thickness specimen was observed to undergo a contraction instead of the anticipated expansion on cooling. Continued cycling of the three specimens from room temperature to 2500°F produced additional changes in the dilation behavior. These changes did not seem to be related to the fabrication direction of the alloy because the values of a1 for the longitudinal, transverse, and thickness specimens varied unpredictably in magnitude and sign. Furthermore, both the longitudinal and transverse specimens showed all three types of dilation curves at least once during the six cycles that they received. Fig. 2 is a sketch of the transverse specimen after

Jan 1, 1967

By R. W. Carpenter, J. C. Ogle

It is possible, by using pack-rolling instead of conventional rolling, to reduce a number of metals to thicknesses of 2µm or less. Such thinfoils are generally made at room temperature without intermediate annealing. In addition, pack-rolled foils fail by developing pinholes at thicknesses near 2µm instead of developing the shear cracks usually observed in cold-rolled ductile metals. This paper presents the results of a general investigation of the deformation substructure and texture developed in copper and iron pack -rolled from 130 to about 2µm thickness. Electron microscopy showed that in both metals a fine (0.2 to 0.5?µ m) deformation subgrain structure formed during pack-rolling; in neither case was this substructure grossly different from substructures formed during conventional rolling. The deformation texture formed in pack-rolled iron was quite similar to usual bcc textures; however, in the case of copper, the cube texture was stable during pack-rolling and the normal copper deformation texture was unstable. It is shown analytically that the constraining pack induced a large hydrostatic pressure in the foils during pack-rolling. The pinhole failure mechanism is attributed to the presence of the large hydrostatic pressure during pack-rolling; this strongly suppressed the growth of shear cracks. The stability of the cube texture in copper is also probably due to the unusuul stress distribution developed during pack-rolling. EXPERIMENTS at several laboratories have shown that very thin foils of the common structural metals and many of the rare earths can be made by "pack-rolling". 1-3 The technique was originally developed to make specimens for nuclear scattering experiments and foils for X-ray filters. It is also useful for making experimental laminar metallic composite bodies and foils thin enough for direct examination by ultra-high voltage electron microscopy without the need for special thinning techniques. Pack-rolling in the present context means a three-layer pack, with the material to be rolled into foil comprising the center layer. The outer two layers, which constrain the foil during reduction, are ordinarily austenitic stainless steel. Typically, a 130 µm (0.005 in.) metal strip can be reduced to a final thickness of 2 µm or less by this process. This is accomplished at room temperature, without intermediate annealing. It has been observed that foils produced by this process do not exhibit at any stage of their reduction the severe work-hardening found in strip rolled by conventional cold-rolling methods. Neither is the failure characteristic the same."&apos; Conventionally cold-rolled ductile metal strip fails by developing shear cracks on planes whose normals nearly bisect the angle between the rolling direction and normal to the rolling plane; these are planes of maximum shear stress. In pack-rolling this mechanism has not been observed; failure occurs by the formation of pinholes on the foil surface (penetrating the foil). If pack-rolling is continued the hole density increases. These differences in behavior imply the existence of appreciably different substructure in pack-rolled foils compared to substructure in conventionally rolled material, or perhaps that the geometry of pack-rolling has an effect on the foil behavior. This paper describes an investigation of deformation substructure and texture in some specimens of pack-rolled copper and iron, and some considerations of the stress distribution in the foils during rolling that result from the geometry of pack-rolling. EXPERIMENTAL DETAILS Three different materials were used for pack-rolling in the present work: soft copper sheet (99.8 pct Cu, 0.03 pct 0, electrolytic tough pitch) and two types of iron, Ferrovac E* and Armco iron. Each was "Crucible Stccl Co. initially in the form of 130 µm annealed strip with grain size ranges of approximately 10 to 40 µm. The initial texture of the copper (determined as noted below) was the normally observed cube type (001)[100]; there was evidence of a small amount of material in the cube-twin orientation reported by Beck and Hu.4 The initial texture of the Ferrovac E was similar to that reported for recrystallized iron by Kurdjumov and sachs,5 who list the principal orientations as {111}<112>, {001}<110> 15degfrom RD and a weak component {112}(110) 15 deg from RD. The starting texture of the Armco iron was not determined. Pack-Rolling Procedure. A four-high mill was used for all specimens. The work roll and backing roll diameters were 1.625 and 5.25 in., respectively. The peripheral roll speed of the work rolls was about 2.5 in. per sec. All foils were initially reduced from 130 to 100 µm by conventional straight rolling and then inserted into a pack, without any intermediate annealing, for further reduction. The pack consisted of an 0.033 in. (838 µm) thick 3 by 6 in. polished sheet of austenitic stainless steel, folded to make a 3 by 3 in. jacket. After folding, the jacket was given a small reduction to close the fold tightly before insertion of the foil. During pack-rolling a constant change in roll spacing was made every third pass. The roll-spacing change corresponded to a 5 pct reduction in thickness for a new pack. This approached a 10 pct reduction when the pack had decreased to about half its original thickness. At this point the deformed pack was discarded and a new one

Jan 1, 1970

By Frederick N. Rhines, Robert F. Mehl

Relatively few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZnz, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.* Fundamentally, methods for the determination of the state of molecular aggregation in solution depend upon the kinetic behavior of the particles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecular solid solution would be afforded. Freche5 examined the rates of

Jan 1, 1940

By Frederick N. Rhines, Robert F. Mehl

Relatively few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZnz, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.* Fundamentally, methods for the determination of the state of molecular aggregation in solution depend upon the kinetic behavior of the particles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecular solid solution would be afforded. Freche5 examined the rates of

Jan 1, 1940