Search Documents

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964

By W. R. Shimer

IN his valuable report on Finishing Temperatures and Properties of Rails, I Dr. G. K. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying put the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. . Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development ,of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high per centages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility, than. rails of identically the same composition and section which were rolled, direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 3, 1915

By J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and ferric iron concentration. The results have been discussed in terms of the adsorption of ferric cations and ferric hydroxide to the quartz surface. Possible relationships between the experimental results and the flotation of quartz have been examined. The adsorption of multivalent cations at the surface of quartz has been studied by many investigators who have used a variety of experimental techniques ranging from streaming potential 1 to radiometric2 measurements. Two possible mechanisms of cation activation of quartz have emerged from the results of these investigations viz: the adsorption of the cation to the negatively charged quartz surface, followed by adsorption of the collector anion to the adsorbed cation site, or: formation of a cation-collector complex which is then adsorbed to the quartz surface. In many natural and industrial systems one of the most prevalent activating species for quartz is ferric iron, this is especially so in the acid-circuit, anionic flotation of iron ore. The adsorption of ferric iron to the quartz surface is complicated by the ability of ferric iron to form complexes with anions, a phenomena which is of minor importance in one of the most widely studied quartz activation processes, ca ++ activation.* *The pK value for [ca(oH)+]/ [ca2+] [oh-] is 1.46 indicating that the influence of Ca (OH)+ ions will be minor in all but strongly alkaline solutions. In order to obtain a better understanding of quartz activation by ferric iron the zeta potential of quartz in the presence of ferric iron has been measured over a range of pH and ferric iron concentration. EXPERIMENTAL METHODS Materials: Selected samples of "rock clystal" quartz from New England, N.S.W., were ground in a pebble mill, washed for three hours in boiling concentrated hydrochloric acid, washed in hot chromic acid and then washed repeatedly with distilled water until the washing water gave no trace of chloride ion.

Jan 1, 1967

Abadilla, Quirico A., Geol.. Lago Pet. Corp Box 172 Maracaiho, Venezuela. IIAbbw. Robert Graham. The W. W. Sly Mfg. Co.Train Ave.. Cleveland. Ohio. Abbotf A. N., Mines Supt., Maznpil Copper Co.. Ltd..Conception del Oro, Zac., Mexico. Abbotf Clarence E, Mgr.. Mines & Quarries, Tenn. Coal. Iron & R. R. Co., 1242 Brown Marx Bldg., Birmingham, Ala. Abbott. Louis Benjamin. Chief Engr.. Consolidation Coal Co. ... .Elkhorn Div., Jenkins, Ky. Abeel, George 8.. Jr., Cons. Min. Engr...4612 West 17th St., Los Angeles, Cal. Abel. Albert E.. Asst. to Pres.. Valley Mould & Iron Corp..Hubbard, Ohio. Abel. Raymond L Asst. Prof., Dept. of Pet. Refin.. Univ. of Pittsburgh. .. .Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min.. Kansas State Teachers College. Pittahurg. Kans. Abernethy, D. Carl, Jr. Min. Engr., Hudson Coal Co. .Scranton, Pa. Abw, Hirouhi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka, Japan. Aborn. Robert H.. Research Assoc.. Mass. Inst. of Tech..Cambridge, Mass. Abouchar. Bylvain Sley. Min. Engr. & Geol., c/o S. H. Sekaly, 13 Rue El Nimr, Cairo, Egypt. tAbozeid. Mahmood. Pet. Min. Engr., Marland Oil Co. of California, Subway Terminal Bldg., Los Angeles, Cal. Abraham. Arthur W.A. pt. 40, Barcelona. Anzoatmui, Venezuela. Abrahams. Alexander I.. Gen'l Mgr., Racon Electrical Co.. ..... .Slough, London, England. tAbrahamuon, C. W., Min. Engr.. The Mond Nickel Co., Ltd.. ..... .Levack. Ont., Canada. Abstein, Henry T.. Engr. & Mgr.. Profile-Tamarack Mines Co.. ...... .Yellow Pine, Idaho. tAcker, E. WC.. Met.. ........ .I28 East Washington Lane. Germantuwn. Philadelphia, Pa. IlAckerman, D. E.. Research Engr.. Research Lab., International Nickel Co., Bayonne, N. J. tAckerman. Ernest R., Pres., Lawrence Portland Cement Co.. . .Plainfield, Union Co., N. J. Adachi. Jinzoo.A..d dress Wanted Adachi, Yuichi, Chief Engr.. Anzan Steel Works, South Manchuria RY. Co., Anzan, South Manchuria. China. (Via Dairen). Adair, Arthur C, Valuation Engr., Internal Revenue. Treasury Dept.. . .Washington, D. C. Adami. Arthur E., Prof. of Min. Engrg., Montana State School of Mines. Butte, Mont. Adami. Charles J.. Min. Engr., Gen'l Mnr., St. Jos~ph Lead Co.. ....... .Bonne Terre, Mo. Adama, C. W., Pres. Adams Pacific Corp .I66 Montgomery St., San Francisco. Cal. Adams. Cuyler .Dee rwood, Minn. Adams, David T, 514 Wrigley Bldg.. Chicago, Ill. ADAMS, FRANK DAWSON, Logan Prof. of Geology and Dean, Faculty of Applied Science. McGiU Univ., Montreal. Que.. Canada. Adams. Gale L, Research Engr.. General Pet. Corp...Los Angeles. Cal. Adams. George I.. Prof. of Geol. & Mineralogy. Univ. of Alabama. .Tuscalmsa, Ala. Adams. H. H.. Cons. Gml..Room 415, W. T. Waggoner Bldg., Fort Worth. Tex. Adams, Henry, Cons. Min. Engr. . 934 Park Ave., Plainfield, N. J. Adame, Henry H. 285 Madison Ave., New York. N. Y. Adams. Henry Farnum. Engr.. Charge Experimental Work, Inspiration Concentrator. Inspiration Cons. Copper Co.. Box 364, Inspiration. Ariz. Adams, Huntington, Min. Engr, 149 Broadway, New York, N. Y. Adams. Leland D, V.P.. Leslie-California Salt Co., 166 Montgomery St.. San Francisco. Cal. Adams. Louie W.. Illinois Steel Co Gary, Ind. Adama, XL L. Min. Engr.. Old Ben Coal Corp., Mine 12.. Christopher. IU. Adams, Robert M. Robert M. Adam Co. .I201 Fidelity Bldg., Duluth, Minn. Adams. Sidney F.. Geol., Empire Zinc Co .Gilman, Colo. tAdams, Waldo Peck..P ittsfield, Pike Co.. Ill. Addams. Charles 1. Min. Engr.. Bo x 663. Phoenix, Ariz. Addicka, Lawrence. Cons. Enar..... .61 Maiden Lane. New York. N. Y. Addison, Herbert, V.P.. Big Horn Collieries Co ,412 Colorado Bldg., Denver, Colo. Adkemn. J. Carson. Min. Engr.. HY Grade Manganese Co., Inc..Woodstock, Va. Ady. Joseph Wesley. Jr.. Min. Enar., 314 Mining Exchange Blda., Colorado Springs, Colo. Affelder. William Lewis. Asst. to Pres., Hillman Coal & Coke Co. & Allied Companies. 2006 First National Bank Bldg.. Pittshurgh, Pa. Ameck, B. F.. Pres.. Universal Portland Cement Co. .. .210 South La Salle St., Chicago. Ill. Agabeg, Edgar C.. Cons. Min. Engr.. ..... .Evelyn Lodae. Asansol, E. I. R. Bengal, India. tAsar. William M.. Aest. Prof. of Geol.. Kirtland Hall, Yale Univ.. ... .New Haven, Conn. Agaeniz. Rodolphe L, Pres.. Calumet & Hecla Consolidated Copper Co. ...... .Boston, Mass. tAgens, William Holmes. District Mgr.. Traylor Engrg. & Mfg. Co., 362 I. W. Hellman Blda.. Los Aneeles. Cal.

Jan 1, 1928

By V. Balasubarmanian, Rajendra Kumar

ISOTHERMAL formation of martensite in a copper-aluminum-nickel alloy was previously reported by Hull and Garwood.' In the present work an attempt has been made to investigate some of the character- istics of the formation of isothermal martensite in binary copper-aluminum alloys containing 14.00 and 14.50 pct Al, respectively. Chill-cast alloys were prepared from OFHC copper and aluminum of greater than 99.5 pct purity. They were homogenized for 24 hr at 950° C. Polished samples were soaked at 1000°C and quenched in water to retain the p phase untransformed; martensite did not form during the quench. The surface was then repolished for isothermal microscopic studies at room temperature. The salient features of the martensitic transformation in copper-aluminum alloys observed in this investigation are: a) The transformation progresses (i) by nuclea-tion at new sites and (ii) by simultaneous slow isothermal growth of existing martensite plates. Slow isothermal growth of martensite has previously been observed by Holden2 in an uranium-chromium alloy and by Hull and Garwood in copper-aluminum-nickel alloy. b) Martensite plates nucleate preferentially at the pin holes formed during the casting of the specimen, Fig. 1. c) Some of the martensite plates pass right through other plates lying in their path, Fig. 1. d) Martensite plates cross grain boundaries without any change in the direction of growth. e) An irregular network of markings, Fig. 2, appears simultaneously with the formation of martensite. It was less prominent in the case of 14.5 pct alloy. The markings may arise due to spontaneous deformation under the lattice strains of the martensitic transformation. Crossing of martensite plates was first observed by Kulin and cohen3 when a high-nickel steel was cooled to 77°K. They suggested that the rapidly advancing plates atquire considerable kinetic energy and strike the obstructing plate with a momentum so as to nucleate the process on the other side of the plate. This, however, fails to explain the present observation where the slow isothermally growing martensite plates cross each other. Such plates would not possess large momentum to bodily displace the obstructing plate. Fig. 1 shows the martensite plates crossing each other without body displacements. This should be contrasted with Fig. 3 of Kulin and Cohen's paper where crossing of plates is accompanied by shearing or body displacements of the plates. The present observations can, how-

Jan 1, 1961

By AIME AIME

HIS many admirers regard the "official"' candidate for president of the Institute in 1934 as far above the average in ability and capacity; but perhaps his outstanding characteristic is dependability. Some men of great brilliance succeed indifferently because they cannot be relied upon. When Howard Nichols Eavenson undertakes to do something he either does it, or he proves to his own satisfaction that the particular object is not attainable. And the latter outcome is exceptional because his judgment is so good that he generally foresees the impossibility and selects in advance a practical alternative. Though a tireless worker he is pretty sure that his energy is not spent futilely.

Jan 1, 1933

By F. C. Canney

Geochemical prospecting seeks hidden mineral deposits by sampling for variations in the chemical composition of naturally occurring materials. Usually the samples are of soils and other products of weathering and erosion—surface materials extremely susceptible to contamination by human activities. Except when a survey is conducted well away from populated areas, contamination is an ever-present hazard. The program's success is particularly endangered when the contaminants are the elements sought; if these occur erratically throughout an area, spurious anomalies completely unrelated to mineralized areas can be formed. Evenly distributed contamination can be dangerous too, if it raises the background to such a level that true anomalies can no longer be easily detected. Suppose, for example, that in an area where the lead background is 20 parts per million the soil over a lead vein contains 1000 ppm of lead. Here the contrast would be 50 to 1, which is very satisfactory for geochemical surveying. Now if 1000 ppm of lead from some source were added evenly to the soil in this area, the contrast would be reduced to about 2 to 1, and the anomaly would no longer be readily detectable because a threshold of significance twice the value of the background is the minimum generally used for interpreting geochemical data. Of the many possible sources of contamination, probably most important are smelter fumes, which may distribute large quantities of metal contaminants over many square miles of ground. For several reasons, the investigation reported here was begun in the Coeur d'Alene district in northern Idaho: 1) a lead smelter has been operated in this district since 1917 and an electrolytic zinc plant since 1928, and presumably the contamination patterns are strongly developed; 2) to evaluate the usefulness of certain geochemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and other veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; 3) one of the economically important parts of the district lies south of the South Fork of Coeur d'Alene River and within a radius of five miles of the reduction plants near Smelterville (Fig. 1). In this area, and in the entire district, conventional methods of prospecting are hindered by heavy vegetation and thick soil cover, and the possibility of contamination by smelter fumes has discouraged geochemical prospecting. Should data reveal that geochemical prospecting could be done successfully in such an area, a particularly useful tool would be available to mining companies and prospectors searching for concealed orebodies in this economically important part of the district. The field work on which this report is based was done from July 28 to 31, 1955. It should be emphasized that this was reconnaissance study only, and therefore far from exhaustive. Previous Investigations in U. S. : The first geochemical survey known to have been affected by contamination was conducted in 1940—a geobotan-ical reconnaissance made in the Michigan copper district by a private company. Geologists found striking variations in the copper content of oak and maple leaves, but unfortunately the high copper isograds of the study seemed to be related more to the Calumet and Hecla copper smelter fall-out than to mineralized ground.' The leaves of one oak tree near the smelter contained 0.4 pct Cu. Similar contamination was reported by Clarke (Ref. 2, p. 41), who conducted experimental geochemical soil and botanical surveys at Ray, Ariz. He found that the leaves of oak trees growing in unmineralized ground near Superior, Ariz., contained more copper than the leaves of oak trees growing on the capping of the Ray orebody and attributed this fact to contamination from the fumes of the Magma smelter at Superior. According to H. E. Hawkes,3 soils and stream sediments in the Superior area are also severely contaminated. Hawkes' work there has shown a copper content averaging 0.5 pct in the surface horizons of soils within one mile of the smelter stack. Samples taken only a few inches below the anomalous surface samples showed only background copper values. In 1950 L. C. Huff' of the USGS made a geochemical survey in an area near Jerome, Ariz., and found considerable zinc and copper in the soils over unmineralized basalt close to Clarkedale, Ariz., and over limestone close to Jerome. As the amounts were notably greater than could reasonably be expected to be derived from the underlying rocks, Huff suspected airborne contamination from the smelter at Clarkedale. Description of Area: The area sampled in detail (Fig. 1) for the study presented here is one of strong relief. The dominant watercourse is the westward-flowing South Fork of the Coeur d'Alene River. East of Kellogg the South Fork flows in a rather narrow canyon, but its valley floor widens considerably to the west where much of the flood plain is covered by an extensive veneer of mining, milling, and smelting debris. South of the South Fork and between Big Creek and Pine Creek is a mountainous area where

Jan 1, 1960

By Enid C. Plante, K. L. Sutherland

PRACTICAL metallurgists are unanimous in stating that oxidation of mined sulphide ore adversely affects separation of the constituent minerals under standard conditions in a mill. Frequently, the need for different operating conditions in different plants is attributed either to the extent of oxidation of the mineral surfaces or to soluble oxidation products. The investigations reported in this paper study the effect of oxidation on the primary condition necessary for flotation, namely that of adhesion of an air bubble to the mineral. OXIDATION PRODUCTS FROM SULPHIDE MINERALS Weinig and Carpenter1 state that the relative rates of oxidation of some sulphides are: FeAsS > FeS2 > CuFeS2 > ZnS >PbS > Cu2S tetrahedrite. They also show that oxidation is rapid at first, that sulphides of older geological formations are more stable than those of recent date and that mixtures oxidize more rapidly than any one mineral alone. The more rapid oxidation of mixtures is borne out by results of Gottschalk and Buehler2 who found that PbS, ZnS and CuS oxidized 8 to 20 times faster when pyrite was present. Only the end products of oxidation, sulphate and the metal ion, were identified in these tests. Gaudin3 states that pyrite is difficult to oxidize in the laboratory. Winchell,4 using pyrite containing 99.98 pct FeS2, allowed water to percolate through a bed of this ground material. At the end of three months only a trace of Fe +++and S04- were found. Even after 10 months the quantity of Fe+++ was only 7.8 mg and S04- 25.5 mg per liter of percolating solution. Carmichael5 confirmed Winchell's results on the slow oxidation of pyrite. Usually the oxidation of sulphide surfaces has been conducted in neutral or acid solutions, the acidity being caused by the oxidation products. Eliseev and Nagirnyak6 found that treatment of pure pyrite with lime gave only thiosulphate, but considered it possible that thiosulphate was obtained not by oxidation of the pyrite itself, but by oxidation of calcium disulphide. Mitrofanov7 suggested that thiosulphate was formed by the following process: oxidation of sulphide to give free sulphur (this frequently happens with marcasite), followed by oxidation of the sulphur to sulphur dioxide and reaction of the sulphur dioxide with sulphur to give thiosulphate. Ferric and ferrous hydroxides, or similar compounds, were shown to be present. The Research Staff of the United Verde Copper Co.8 treated ore from the United Verde mine with lime. Thiosulphate, sulphide and polysulphides were stated to be

Jan 1, 1947

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By T. K. Prentice

The January-February number of the Journal of the Chemical Metallurgical and Mining Society of South Africa, 1943, is made up entirely of a discussion of Ball Wear in Cylindrical Mills. Following the principal paper by T. K. Prentice are several remarkably pertinent and carefully prepared discussions. Few persons in this country would be likely to see this publication, and since the information presented is new and of current interest, it seems desirable to abstract and review this publication for the benefit of the members of the A.I.M.E. The purpose of the investigation is stated in the first two paragraphs of Prentice's paper, as follows: Early in 1941, The Chamber of Mines Steel Products, Limited, initiated a series of tests under semi-working scale conditions to determine, if possible, those physical and chemical properties of a ball which make it resistant to wear when used in a cylindrical mill as a grinding medium, with the primary object of incorporating those beneficial qualities in the balls being produced at their works. This paper describes the tests carried out and discusses the results obtained. From these results it was possible to formulate a new theory relating to ball wear in cylindrical mills. This theory is presented in the second portion of this paper. Practical Ball-mill Tests in a Cylindrical Mill Part I of the paper begins with a discussion of the methods used for the manu- facture of grinding balls in South Africa. The following paragraph is of particular interest. The cast steel ingots, 4¼ in. square by 3 ft. 6 in. long, are re-heated in a gas-fired sloping stationary-hearth furnace and then rolled in a six-pass continuous mill into 25/8 in. round billets. Some of these billets are then removed and cut into suitable lengths for forging into 4 in., 3¼ in. , 3 in. or 2½ in. balls by means of three Drop and two Beche hammers, but the greater number, whilst still at about 1,000, pass directly into a set of scroll rolls which produce, in an ingenious manner, finished 3 in. balls direct from the 25/8 in. billets. Except in special cases, all balls are allowed to cool in the atmosphere and are not water quenched. Details of the Tests In order to enable the reader to evaluate properly the results and conclusions in the rest of the paper and in the discussions following the paper, most of the information presented by the author under this heading is quoted: The testing unit was a nominal 30 in. diameter and 18 in. long centre discharge Denver Ball Mill. The ore pulp to the ball mill comprised a small portion of the normal feed to one of the fourteen City Deep 5 ft. 6 in. X 22 ft. tube mills, and the grinding media consisted of the balls under test plus other balls to give the desired load. The running time of the test-mill was divided into approximately equal periods of five days 13½ hours each. The usual procedure was to examine and make up the load

Jan 1, 1947

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By N. S. Wagner, R. S. Mason

The production of lightweight aggregates in Oregon is a new industry, and, like all new enterprises, it is suffering from growing pains characterized by numerous, small operations some of which flourish for a short time and then cease altogether. Norinally all industrial mineral products are produced in a highly competitive atmosphere. At the present time this condition does not exist to a very marked degree in the state because as yet producers have not saturated the constantly expanding market. This paper has been prepared with the intention of outlining very briefly the current status of the various products now heing used as lightweight aggregates in Oregon. The present piche will surely change, perhaps quite radically within even a short space of time. Lightweight Aggregates Used in the Northwest PUMICE Interest in Oregon pumice is not new. Deposits are abundant. Successful development, however, dates only from 1946. During 1948 a total of nine operations was engaged in full or part-time production of aggregate. The postwar building boom and increased public consciousness regarding the value of insulation are the immediate reasons behind the current development. Just how firmly this production of pumice aggregate may be established is something which cannot be foretold at the present time. Much will depend upon how successfully the pumice aggregate construction already installed stands the test of time. Some fine pumice aggregate products have been made and it seems probable that because of its unique properties a certain demand for pumice aggregate will continue in the future. Fire-proof, rodent-proof, decay-resistant properties supplement the lightness in weight and insulation properties of pumice aggregate products in rendering them particularly ideal for many types of construction. In addition there has been fabrication in the form of reinforced fence posts, street markers, and similar products of a specialized-product nature and these are not to be overlooked in terms of future production. Also pertinent to how soundlj pumice aggregate production is established will be possible future competition with other lightweight aggregates. However, this situation will be governed largely by competitive costs of production and marketing. For its present use, which is almost exclusively limited to the manufacturing of building blocks, the market for Oregon pumice aggregate has been extended from the mining area around Rend and Chemult to points as far distant as San Francisco and Seattle. Naturally enough the bulk of the production goes to the Portland and eastern Oregon consumers. Shipments are made by both rail and truck. Early in 1947 the State Department of Geology and Mineral Industries made a canvass of all pumice producers in the state. The production for 1956 amounted to 26,614 cu yd and was valued at $13,649 at the plants. The United States Bureau of Mines estimates the production for 1947 as 33,240 short tons valued at $111,380. This is roughly 65,000 cu yd. No data are available for the 1948 production but it is understood to exceed that for 1947. The Oregon pumice occurrences originated largely from the eruption of Mount Mazama, the name of the formerly active volcano and the location of Crater Lake. Other lesser volcanoes throughout the area contributed to the present occurrences, however, and it has been estimated by Moore' that the pumice deposits cover an area of some 3500 square miles. This area lies east of Crater Lake between Bend and Klamath Falls and embraces the southern portion of Deschutes County, the northern part of Klamath County, and the northwest corner of Lake County. Thickness of the pumice ranges from thin skims to local thicknesses of as much as 30 to 40 ft. Fragment size also varies greatly. Any attempt to describe the situation by giving screen analyses would be confusing because of the wide variations to be found in all area of this size. The picture can best be summed up by stating that places showing great variations in fragment size can be found if a search for extremes is made. For mining purposes in connection with aggregate production, it call be stated that miles and miles of pumice exist in which the fragrnent sizes range from an inch or so downward. The usual color of the pumice is a light gray to off-white. A typical pumice analysis shows a silica content of about 69 pct, alumina 15 pct, and sodium oxide about 5 pct. Potash, lime, and water are the next three most abundant constituents, running just a little over 2 pct each. Iron oxides are fairly constant at 2.75 pct. Titanium, manganese, magnesium, and phosphorus occur in amounts of less than 1 pct. All of the foregoing substances are combined as a glass exhibiting cellular structure. The weight of crushed but otherwise pit-run (undried) pumice runs around 1100 Ib per cu yd according to figures furnished by various producers. The minimum and maximum weights per cubic yard reported are 1050 and 1400 lb, respectively. The 1400 lb per cu yd pumice contrasts with the pumice from most of the other

Jan 1, 1950

By R. P. Smith

In 1937 the employees of the Hollinger Consolidated Gold Mines Ltd.. at Timmins. Ont., Canada, approached organized medicine for a plan to provide themselves and their families with a complete medical service including hospitalization. This approach was made because of two conditions: (1) the necessity for some organization whereby contributions could be made in instalments to offset the sudden and large expense connected with illness for which the average employee is not prepared, and (2) the need for a more cohesive quality of service to replace a contract practice then in vogue, which did not take care of the employee's family or dependents. In different parts of the United States and Canada similar plans were in force, not only for employed groups but for numbers of people in circumscribed areas. In Europe different countries had adopted various forms of health insurance plans. It then was no surprise that these employees as a group should ask for some similar plan. With the cooperation of the management, a plan was instituted. The plan has one object only—the provision of medical services, including the accessory services such as hospitaliza-tion, X-rays, nursing, and necessary drugs and medicines. It is not concerned with cash benefits, sickness and accident payments, or any form of monetary return as the result of illness, but is simply an organization to provide medical services and pay for them from a central fund. It is a nonprofit organization and the only shareholders are the employees and their families who contribute and who in turn receive services. The Hollinger plan is limited to the employees of the Hollinger mine, who live in Timmins and the immediate vicinity. At first, the membership was voluntary. In the third year, it was made a condition of employment, with the proviso that at the end of any Association financial year an employee may withdraw if he wishes to do so. After withdrawal, he cannot again become a member until the end of the next Association year, and then only by the payment of the back dues. This step was taken to ensure continuity, and to prevent employees from withdrawing when well and reentering when faced with impending illness or operations. The employee himself is subject to medical examination on application for employment, and if accepted is subject to further examination by a specialist in chest diseases under the Workmen's Compensation Board of Ontario. Thus it is possible to exclude those who have heart disease, tuberculosis, or other disabling conditions when first employed. Wives and families of employees are not subject to medical examination but other dependents of an employee—mother, father, or other relative—who are declared by the employee to be wholly dependent upon him must be examined. The employee

Jan 1, 1946

By H. A. Lequear, J. D. Lubahn

A sudden change from one constant strain rate to another during a tensile test causes an unusual transient in aluminum alloy 61ST. A sudden change from one constant stress to another during a creep test does not produce an unusual transient in this material. A specially devised test shows that the nature of the previous steady-state conditions, which the sudden change disturbs, is one of the factors affecting the transient behavior. Some of the observations may be explained in terms of strain aging. USUALLY a sudden change during a tensile test from one constant strain rate to another causes a small, abrupt vertical shift from one stress-strain curve to another, parallel one. This behavior is apparently characteristic of all metals at very low temperatures and of many metals for wide ranges of temperature. It is illustrated in Fig. 1 for some early data on 61ST tested at — 195oC, and in Fig. 2 for some recent data on copper at room temperature. The greater accuracy of the results of Fig. 2 over previous ones' is due to the equipment shown in Fig. 3. Three levers apply the bulk of the load, while the changes in the small remainder load are indicated sensitively by a low capacity load scale. Refs. 2 and 3 describe the recording equipment. A test like those in Figs. 1 and 2 provides the information necessary to determine the rate sensitizrity, n,4 of the metal. ( a log s ) ? log s n = ------------------------ ----------------------------= ( a logs e, ? log e logS2-logS1 log S2/S1 log i2 — log e1 log e2/e1 where S equals stress: e is logarithmic strain or natural logarithm of (final gage length/initial gage length);" i is strain rate or de/dt: and n is rate sensitivity, rate of change of log stress with log strain rate at a given strain, or (a log S/a log i),. Normally, the rate sensitivity, n, is positive, which means that an increase in stress causes an increase in rate. However, certain exceptions, attributed to strain aging,5 have been observed. Fig. 2 indicates how rate sensitivity values are derived from the measurements. Table I summarizes the rate sensitivity values derivable from Fig. 1. In contrast to the behavior of copper in Fig. 2, the aluminum alloy 61ST, which strain ages when tested near room temperature, exhibits an unusual transient when the strain rate is suddenly changed,' as shown in Fig. 4. Initially, there is a comparatively sudden vertical shift of the stress-strain curve in a direction corresponding to the rate change, but then the curve gradually shifts back again. The initial shift is not as sudden as might be expected, because the testing machine is unable to achieve the impressed rate change instantaneously, as illustrated in Fig. 2. The behavior shown in Fig. 4 will be referred to as a tensile transient, the word tensile implying that the behavior was observed in a tension type of test. The corresponding test, where the strain rate is maintained constant except for the sudden change, will be called a tensile transient test. A creep transient, by contrast, will be defined as a temporarily abnormal behavior in a creep transient test, where there is a sudden change from one constant load to another.' In Fig. 4, a naive look at the gradually decreasing and then increasing load after a sudden rate incre-

Jan 1, 1957

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant' on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,' aging took place during the creep tests. 'In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500' or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500' or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40' to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.' At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

To Install Waste Heat Boiler at White Pine White Pine Copper Co.'s smelter 18 miles southwest of Ontonagon, Mich., will have a six story high boiler utilizing what otherwise would be waste heat from a copper reverberatory furnace. Designed and under construction by the Babcock & Wilcox Co., the boiler will supply steam to a turbo-generator furnishing power for the projected development. The boiler will be in line with and following the reverberatory furnace. Using waste heat from the furnace in place of fuel for steam generation, about 50 pct of heat in the fuel originally supplied to the furnace will be recovered by the waste heat boiler. Exploration conducted over the past 15 years at White Pine, wholly owned subsidiary of Copper Range Co., has disclosed reserves of 309 million tons averaging 21.3 lb of copper per ton. Ore mineral is chiefly chalcocite (Cu2s).

Jan 5, 1953

By means of top-slicing methods, wide veins, masses, or thick beds of soft ore may be mined, where the caving of the overburden is of no consequence. The ore is mined in a series of horizontal floors or slices, taken in descending order, from the top of the deposit. Each floor is mined in small sections, the roof of each section being allowed or forced to cave before an adjacent section is attacked. The method as used in two mining districts—Marquette, iron, and Pachuca, silver-gold—is described in the two papers following:

Jan 1, 1925

By J. Rogers, K. L. Sutherland

THE relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. EXPERIMENTAL PROCEDURE The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testing18 have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.25 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

MEMBERS, JUNIOR MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES LIST OF MEMBERS ALPHABETICALLY ARRANGED EXPLANATION OF SYMBOLS ** Junior Member. t Associate. || Junior Associate. Members are not marked. Capital letters signify Honorary membership. Student Associate and Rocky Mountain members on pages 165-167. Abadilla. Quirico A Catanawan. Tayabas, P. I. Abbey. Robert Graham. District Mgr The W. W. Sly Mfn. Co., 60 Church St New York. N. Y. Abbott. A. N Mines Supt Mazapil Copper Co Ltd . .Conception del Oro. Zac., Mexico. Abbott. Ckrence E Mgr Mines & Quarries, Tenn. Coal. Iron & R. R. Co 1242 Brown Marx Bldg Birminrham. Ala. Abbott. Louie Benjamin. Chief Enar Consolidation Coal Co Elkhorn Div .Jenkins, KY. Abeel. Gsorge H Jr., Cons. Min. Enar .Box 427. Santa Monica. Cal. Abel. Albert E Asst. to Pres Valley Mould & Iron Corp Hubbard. Ohio. Abel. Raymond L. Asst. Prof., Dept. of Pet. Refin Univ. of Pittsburgh Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min Kansas State Teachers College. Pittsburg. Kans. IlAbernethy. D. Carl, Jr. Min. Engr Hudson Coal Co .Scranton. Pa. Abey, Hiroshi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka. Japan. tAbarn, Robert H Instructor in Met Harvard University Cambridge, Mass tAbozeid,Mahmood. Pet. Production E r . . Marland Oil Co. Ponca City, Okla. Abraham. Arthur W Geol., Richfield Oil Co Box 788. Bakersfield, Cal. Abraham, W. E. V Member, Staff of Burmah Oil Co Ltd. Nyaunghla. Upper Burmz, India. Abrahams. Alexander I Gen'l Mgr., Racon Electrical Co Slough, Bucks England. tAbrahammn. C. W Min. Engr The Mond Nickel Co Ltd . Coniston, Ont Canada. IlAbmn. Guy W., Asst. Metallographist, Youngstown Sheet & Tube Co., Research Dept., Youngstown. Ohio. Abstein. Henry T., Engr. & Mgr Profile-Tamarack Mines Co . .Yellow Pine, Idaho. tAcker. E. O'C Met I28 East Washington Lane. Germantown, Philadelphia. Pa. Ackerman. D. E Met. Research Lab International Nickel Co Inc Bayonne. N. J. tAbckerman. Ernest R Pres., Lawrence Portland Cement Co . .Plainfield. Union Co N. J. ||Ackerman. George F Jr. Min. Engr El Potosi Min. Co. .Apt. 13. Chihuahua, Chih Mexico. Acres, T. H Geol. Dept Valuation & Pet. Engr., Richfield Oil Co. 655 S. Flower St Los Angeles. Cal. Adachi. Jinzoo Address Wanted. Adair. Arthur C Valuation Enar., Internal Revenue. Treasury Dept., Washington, D. C. Adam. John. Min. Ennr., The Zinc Corp. Ltd., Box 4 C. Broken Hill, N. S. W Australia. Adami. Arthur E V. P Montana State School of Mines.Butte, Mont. Adami. Charles J Min. Ensr St. Joseph Lead Co 4540 Lindel Blvd., St. Louis, Mo. Adams. C. W.729 South Normandie St LaGranada Apt Los Angeles, Cal. Adams. Cmyler Geerwwd. Minn. Adams. F. J Gen'l Anent. Gulf Production & Pipa Line Cos .Fort Worth. Tex. ADAMS. FRANK DAWSON. Logan Prof. of Geology and Dean, Faculty of Applied Science, McGill Univ Montreal. Que Canada. Adama, Gale L Research Enar., General Pet. Corp. of California, Higgins Bldg Los Angeles. Cal. Adams. George I, Prof. of Geol. & Mineralogy Univ. of Alabama, Tuscaloosa, Ala. Adams. H. H Cons. Geol Room 416, W. T. Waagoner Bldg Fort Worth. Tex. Adams, Henry. Cons. Min. Ennr 1050 Edgewood Ave., Plainfield, N. J. Adams, Henry H.285 Madison Ave., New York. N. Y. Adams, Henry Farnum. Engr., Charge. Experimental Work. Inspiration Concentrator, Inspiration Cons. Copper Co Box 354. Inspiration. Ariz. Adams. Huntington. Min. Enar I41 Broadway, New York. N. Y. Mama, Leland D., V. P., Leslie-California Salt Co 166 Montgomery St., San Francisco, Cal. Adams, Louis W., Illinois Steel Co .Gary. Ind.

Jan 1, 1929

By Heath B. Fowler

The surface mining operations of the Simplot Fertilizer Co. are on the Fort Hall Indian Reservation approximately 16 miles east of Fort Hall, Idaho (Fig 1). The Phosphoria formation outcrops in sec. 2, 3, 11, 14, 15, 22 and 27, T 4 S, R 37 E, Boise Meridian. The ownership of these phosphate-bearing lands is divided between individual Indians and the Bannock-Shoshone Tribe, and the royalties are paid to the respective owners on a tonnage basis, as the rock is mined. The geology and mineral resources of the Fort Hall Reservation were studied by the U. S. Geological Survey in 1913 and reported on in 1920. † However, it was not until the winter of 1945 that exploratory work was undertaken by private enterprise. Diamond drilling was begun by the Simplot Fertilizer Co. in April 1946, and stripping operations were started in June. A camp was established near

Jan 1, 1950