Search Documents

By C. P. Kempter, H. L. Brown

Recently Chang determined heat content values of tantalum monocarbide and tungsten monocarbide from 325" to985°Kand 326" to 912"K, respectively, and, using other published data, made certain solid-state calculations for these two compounds. Chang expressed his Cp values in units of cal per "g-atom alloy" OK. We consider this poor usage since l) tantalum monocarbide and tungsten monocarbide are not alloys, and 2) an atom of an alloy does not exist. However, one may convert his values to units of cal per mole OK by merely doubling them. For TaC he calculated a Nernst-Lindemann parameter of 9.07 x lo-' "g-atom per cal". We have refined the calculation of this parameter and have arrived at a much lower value. Rather than approximating the true coefficient of volume expansion, a,, as three times the true coefficient of linear expansion, a, we calculated u, from the TaCo.99, lattice expansion data of Fries and Wahman.38 At 25°C a, = 14.3 x 10s per OC. The molar volume was calculated to be 13.32 cu cm per mole at 25°C. From the lattice compression data of Champion and Drickamer~' for "TaC,.,," we determined the room-temperature compressibility to be 3.5 x 10-l3 sq cm per dyne by plotting l/Vo (aV/ap) vs applied pressure. (Since the lowest pressure at which Champion and Drickamer reported a relative volume was 20 kbars, one may calculate an approximate compressibility only. Chang calculated a compressibility of 3.175 x 10-l3 sq cm per dyne from the same data.) We also used twice Chang's value of Cp = 4.38 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated a Nernst-Lindemann parameter of 5.8 x 10-l4 mole per erg or 2.4 x lo- ' mole per cal, and a Cdil value of 2.3 x 10' ergs per mole OK. In the case of tungsten monocarbide no isothermal compressibility has been reported; however, one may calculate an approximate Nernst-Lindemann parameter by using the adiabatic compressibility reported by Brown, Armstrong, and Kempter." Using the WC lattice expansion data of Mauer and Bolz~l we calculated a, to be 12., x l0-' per OC. The molar volume was calculated to be 12.5 cu cm per mole. We used twice Chang's value of Cp = 4.18 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated an approximate Nernst-Lindemann parameter of 2 x lo-' mole per cal, which is much

Jan 1, 1969

By W. L. Phillips

Stress-strain data are reported for sodium chloride, lithium fluoride, and magnesium oxide tested in compression at diffevent strain rates in the telrlperature range from 70° to 873°K. Quantitative equations are given for the stvain-rate dependence of the critical resolved shear stress and the initial rate of work havdening. The properties so determined are compared with results previously reported for metals. ALTHOUGH the effects of strain rate and temperature on the stress-strain characteristics of metals have been extensively investigated1,2 these effects have not been studied in detail in ionic crystals. In the only previous investigations on the effect of strain rate on the deformation of ionic crystals. Gilman and gohnston3 and Hulse and pask4 have shown that the yield stress of lithium fluoride and magnesium oxide at room temperature is proportional to the ninth or tenth root of the strain rate. CRYSTAL PREPARATION Lithium fluoride, sodium chloride. and magnesium oxide single crystals were purchased from the Har-shaw Chemical Co. The compression fixture and sample preparation have been described in detail previously.5 The detectable impurities in MgO were eight parts in 105 of Fe and six parts in 105 of Si; in LiF, six parts in 105 of Mg; and in NaC1, two parts in 105 of Fe and four parts in 10&apos; of Mg. The cleaved samples measured - 0.1 in. by 0.1 in. by 0.3 in. Prior to testing all samples were annealed at -0.8 of their melting point and cooled to room tempera- ture at 50 C per hr.&apos; Samples were strained at rates (<) of 0.1, 0.01, 0.002, and 0.0002 in. per in. per min. EXPERIMENTAL RESULTS Fig. 1 is a plot of the critical resolved shear stress a,. (extrapolation of slope of easy glide region to zero strain) of sodium chloride, lithium fluoride, and magnesium oxide tested at different strain rates as a function of temperature. In all crystals at all strain rates a, decreases with increasing temperature according to an equation of the type397 where uo is a stress constant, K is a constant, and T is the absolute temperature. The points in Fig. 1 are the average of six tests. It is evident that there is a break in the log 0,- temperature plots at a characteristic temperature T,. The constant K of Eq. [I] is dependent on strain rate, Fig. 2. The relationship

Jan 1, 1962

By J. G. Y. Chow, S. B. McRickard

The tensi1e properties of Ferrovac iron have been studied from 4° to 300°K. The stress required for macroscopic yielding was found to he constant below approximately 50°K. The effect of mechanical twinning on this low -temperature stress plateau was investigated. The onset of twinning occurs in this iron between 130° and 150°K and depending on its previous thermal history the twinning-stress curue may drop below or remain above the vield-stress curves as the temperature is lowered. Twinning has been shown to initiate slip in quenclzed iron at low temperatures. In no instances, however, did the onset of twinning alter the continuity of the yield stress -tempwature curve. Our data shows that carbon inhibits twinning and slip at low tem-peratures. This observation nay be used to explain the ductile-to-brittle transition in iron. The effect of fast neutron irradiation on yielding and embrittlement in iron and Fe-C alloys is offered as supporting evidence for this viewpoint. THE mode of yielding in iron at low temperatures was studied in an attempt to find an expression based on a single mechanism to describe the thermal dependence of the yield stress of iron. There are two types of inflections observed in the variation of the yield stress with temperature in iron and Fe-C alloys. The first is associated with ductile behavior and consists of a region extending 50" to 100°K above absolute zero in which the yield stress is independent of temperature. The second is observed in more brittle materials such as Fe-C alloys and irradiated iron and consists of an abrupt discontinuity in the yield curve as the temperature is lowered through a ductile-to-brittle transition point. The temperature dependence of the yield stress for iron with four grain diameters as found in this study is shown in Fig. 1. To varying degrees all the curves appear to flatten or approach an asymptotic value as the temperature is lowered below 50°K. Several other investigators1,2 have observed a plateau in the yield stress of iron and steel at low temperatures and in 1956 Louat3 presented a theory which contained an explanation for this behavior. In a subsequent exchange with Erickson and Low4&apos;5 who attributed the plateau to the onset of mechanical twinning Louat8 showed that twinning first occurs in iron and steel tested in tension at temperatures as high as 140°K which is well above the observed plateau in yield stress. Furthermore he pointed out that both twinning and slip are basically dislocation processes and that with modified parameters his original theory still applied when deformation is initiated by twinning. Variables which affect the ductile-to-brittle transition in iron are test temperature, strain rate, composition and grain size.7 LOW,8 Hahn et al.,9 and Hull10 have provided evidence which links brittle fracture at a given temperature with the specimen grain size and the onset of twinning. In fact, Hull equates the brittle fracture stress to the twinning stress. On the other hand brittle fracture has been observed in the absence of twinning and priestnerl1 has given a fracture criterion which is valid whether or not fracture is preceded by extensive twinning. The data presented here clarify the role of twinning in the low-temperature deformation of iron. Strong evidence is given that the amount and distribution of interstitial impurities such as carbon are of

Jan 1, 1965

By John Greenawalt

IN view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by com-bustion within the mass itself. Its first successful application, in connec-tion with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremen-dous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blown off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for ignit-ing purposes.

Jan 1, 1938

By Paul C. Merritt

Chrysotile asbestos producers in Quebec may soon experience a unique situation-i.e., strong competition from American ore sources for the short fiber market west of the Mississippi River. This com- petition will be forthcoming from Copperopolis and Coalinga, two deposits now being developed on opposite flanks of the San Joaquin Valley in central California. The combined output now planned from both deposits is 100,000 tons annually, equivalent to about 50% of the annual market demand in the western, central and Gulf States, and more than twice the tonnage sold in 1960 by all other American asbestos producers combined. The principal companies involved in these new undertakings are Jefferson Lake Asbestos Corp. (subsidiary of Jefferson Lake Sulphur Co.), Hidden Splendor Mining Co., Coalinga Asbestos Co. (Johns- Manville Corp. in conjunction with Kern County Land Co.), Union Carbide Corp., and Asbestos Corp. Ltd. Jefferson Lake&apos;s principal interest is at Copperopolis where the company&apos;s new 70,000-ton per yr mill recently went on stream. The company also holds some claims at Coalinga, but this latter area is better known as the site where Hidden Splendor, Coalinga Asbestos Co. and Todd Industries (a local company) have established operating mines and mills capable of turning out 30,000 tons of fiber each year. Coalinga is also the site of exploration by Union Carbide Nuclear and Asbestos Corp. Ltd.

Jan 9, 1962

By C. M. WEILD

ATTENTION has been turned recently to the exploration and development of certain large blanket-deposits of brown iron-ore in Cuba. The most conspicuous of these to-day, and the one upon which the most light has been shed, is the Mayari deposit, situated about 15 miles south of Nipe bay. Here the Spanish-American Co. has sole control over 18,500 acres of ore-bearing lands, reported by its engineers to contain 500,000,000 tons of ore; and the necessary plant and equipment, with docks and railways, is now under construction for the early marketing of this ore. A similar deposit, and undoubtedly the next to be exploited, is the ore-field at Moa bay, where 13,000 to 15,000 acres of ore-lands, immediately adjacent to the shores of an excellent harbor, have been generously covered by numerous mining-claims, practically all controlled by four large interests. This deposit is now estimated to contain approximately 350,000,000 tons, on the basis of dried ore ready for shipment, a figure which may be increased when the western limits of the ore-deposit have been more accurately defined. Other deposits of the same type, but smaller and less accessible, are those at Cubitas, situated from 12 to 15 miles north of Camaguey city, and at Taco bay and Navas, points lying a few miles west of Baracoa. The area of the Cubitas deposit is said to be 6,000 acres, and the yield of ore is estimated at 150,000,000 tons. The Baracoa. deposits are less well known, but preliminary estimates have placed their joint ore-reserves at 40,000,000 tons. Accepting the above tonnages as reasonably correct, we conclude that the deposits enumerated give promise of adding about 1,000,000,000 tons of iron-ore to the world&apos;s supply; they have, therefore, to be considered in any attempt to fore-

Aug 1, 1909

By Alfred H. Brooks

LESS than a decade ago the consumption of coal in Alaska was practically limited to the salmon canneries and the few lode-mines and settlements along the Pacific coast of the Ter¬ritory. The sparse population of the interior depended on the forests, that of the shores of Bering Sea and the Arctic Ocean on driftwood for fuel. All this has changed. The thousands who have sought and mined gold on the Seward peninsula since 1898 have much impoverished the long-accumulated supply of driftwood, and at the same time the constantly increasing demand for fuel, on the part of the placer-camps and steamers, has resulted in heavy inroads being made on the accessible timber of the Yukon and its tributaries. While on the one hand the immediately available store of wood has decreased, on the other the consumption of fuel because of the rapid expansion of the mining and fishery industries and the attendant growth of population has much increased. Alaska, therefore, offers a constantly growing market for coal and other fuels. As the local coal-production has been insignificant, the demand has been met by importations from Washington, British Columbia, and even from Pennsylvania and Australia. Fuel-Consumption Mr. D. H. Jarvis, Collector for Alaska, has kept systematic records of the trade of the Territory since 1903. The statistics of the coal-importations of the past two years are shown in Table I. If data were available for a longer period of years, the increase of coal-importations would be much more striking.

Jul 1, 1905

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker&apos; will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By T. Rosenqvist

From the chemical, metallurgical, and mineralogical points of view, the importance of thermodynamic data for metal-sulphides and sulphur dissolved in molten metal has long been realized. Such data will give a basis for thermo-dynamic calculations of processes such as roasting and the distribution of sulphur between molten metal and slags. Furthermore, it will help us understand the chemical forces which tie sulphur to the metal and to the melt. Thermodynamic studies of solid sulphides and the equilibria between solid sulphides and metals have been carried out in a rather large number of cases by several investigators. An excellent review of this work is given by Kelley.1 On the other hand, very little is known about the thermodynamic properties of molten sulphides and of sulphur dissolved in molten metal. The only system which previously has been investigated in this respect is the iron/sulphur system. The purpose of the present investigation was primarily to obtain further data for metalisulphur melts and the system silver/sulphur was chosen, not because this system was expected to be of special interest in itself, but because the silver/sulphur system is a typical example of a metal/sulphur system. Because of the low melting temperatures, the work could be carried out without appreciable furnace and refractory difficulties. The sulphur in this system possesses a rather high escaping tendency compared to most other metal/sulphur systems. By the method employed (reaction with hydrogen to form hydrogen sulphide) this gives ratios Ph2s/Ph2 up to 0.30, which may be determined accurately. &apos;rhermodynamic investigations of the heterogeneous reaction Ag2S +H2 —+ 2Ag + H2S have previously been carried out by Pelabon,2 Keyes and Felsing,3 Jellineb and Zakowski,4 Wat-anabe,6 and Britzke and Kapustinsky.6 Their results are in rather poor agreement. Experimental Part PRINCIPLE In the present invehgation the escaping tendency of sulphur from the condensed phase was determined by the reaction: S + H2 = H2S The ratio Ph2s/Ph2 is at constant temperature, directly proportional to the escaping tendency of sulphur and to its chemical activity in the condensed phase. (This ratio will subsequently be denoted by H2S/H2.) From this ratio and its variation with temperature and with change in the com- position of the condensed phase, thermodyrlamic quantities such as free energy and heat of reaction can be derived. The apparatus used is shown in Fig 1. The silver/sulphur alloy was placed in a crucible inside a refractory tube and mounted inside the furnace to the left. The tube was a part of a closed, gas-tight system in which the gas mixture could circulate until equilibrium was established. Circulation was maintained by the glass propeller to the right, driven by an external magnet, and promoted by the chimney action of the furnace. The gas passed up through the furnace, down into the crucible where it came in contact with the alloy, passed rapidly up through a narrow tube and out of the hot zone. After equilibrium was established between the gas and the condensed phase, the composition of the gas mixture was determined from its density. In its circulation, the gas mixture passed through a chamber (lower right on Fig 1) containing a buoyancy-balance, where the density of the gas was determined by magnetic balancing. From the measured density,

Jan 1, 1950

By Paul M. Tyler

NOW that the dust of World War II has settled and we and our allies are faced with extravagant losses of men, money, and materials, virtually the only hope that the United States and Britain have in the way of reparations lies in the capture of industrial, technical, and scientific secrets. Even during the war American and British scientists and technicians gained access to German factories, questioned German personnel, studied German documents, and endeavored generally to keep pace with new discoveries in science, industrial technology, and process development. Under various agencies this work continued for two years after the war. Altogether at least 600 American scientists and industrialists have gone to Germany and brought back reports and several times as many British, Canadian, and. Australian investigators have been similarly engaged under co-operative arrangements designed to assure the maximum of coverage with a minimum duplication of effort. As a result of these investigations and document studies, about 500 or 600 reports have been prepared on metallurgical and allied subjects. Those by American authors or joint teams have been listed in the annotated Bibliography of Scientific and Industrial Reports, issued by the Office of Technical Services in the U. S. Department of Commerce. Many of the British reports are also available in this country through the same office or through a British representative in New York. Since it was my duty to read most of these reports for

Jan 1, 1948

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES&apos; OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By Robert E. Green, T. Hinton

The velocities of the three possible modes of elastic-wave Propagation have been calculated for single-crystal aluminum at 1-deg intervals throughout the standard steveographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy propagation and specirzen axes are presented as arrows drawn within the standard triangle. The orientation factors associated with dislocation nzotion on the primary slip system only and also on all twelve slip systenzs have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing--7aue resonant specivnen hazle also been calculated. The relevance of these results to ultrasonic attenuation measurements is discussed. DUE to the widespread use of ultrasonics in the investigation of the properties of solids a number of authors15 have discussed in detail the theory of elastic-wave propagation in solids. In this paper the modes of wave propagation are evaluated according to the procedure suggested by reeen&apos; for the case of single-crystal aluminum at 1-deg intervals throughout the standard stereographic triangle. The wave speeds are presented in the form of contour diagrams within the standard triangle. The deviations between the direction of maximum energy propagation and the normals to the wave fronts are presented as arrows drawn within the standard triangle. The orientation-de pendent factors (orientation factors) associated with dislocation damping as derived in the preceding paper6 have been calculated for the case of aluminum at 1-deg intervals throughout the standard triangle. The orientation factors for dislocation motion on the primary slip system only and on all twelve slip systems are presented in the form of contour diagrams, for both the traveling- and the standing-wave conditions. The relevance of these results to ultrasonic attenuation measurements is discussed. ELASTIC-WAVE PROPAGATION Three waves can be propagated in a linear elastic homogeneous anisotropic medium. The velocity of propagation v of each of these waves in a medium of density p can be obtained from the determination of the eigenvalues and eigenvectors of the matrix equa- The A&apos;s are a series of moduli which are functions of the elastic constants cij and the direction cosines 1, m, and n of the specimen axis. In the case of cubic single crystals where there are only three nonzero elastic constants cll, c12, and C, the A&apos;s are, The solution of Eq. [I] will give the wave speeds (eigenvalues) and the direction cosines a, 0, and y of the particle displacements (eigenvectors). To obtain the direction of maximum energy flux requires the calculation of the energy-flux vector ET with com- w is the angular frequency, A, the amplitude, and v the velocity of the wave. The direction cosines a, b, and c of the energy flux vector are then given by

Jan 1, 1967

By Armando M. Lago

Secular and cyclical patterns of postwar sources and uses of funds of the mineral sector are analyzed. A simultaneous equation behavior model of sources and uses of funds is developed for both mining firms and integrated producers, and these models were put through the task of predicting the financial and expenditure be-havior of mineral corporations in response to mergers and changes in investment tax credits and depletion allowances. Finally, the quantitative analysis methodology is applied to the analysis of optimum capital structure of mining corporations. The postwar changes that have occurred in the expenditure and financial behavior of mineral corporations are reviewed, particularly the relative importance of factors that affect the industry&apos;s supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail. An econometric model of mineral corporate financial behavior is formulated. This model is then estimated and reviewed. Policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector are discussed. Finally, the optimum financial structure of mining firms is discussed and the effect of corporate financial structure on the mining corporations&apos; average cost of capital is analyzed.

Jan 1, 1971

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

By J. L. Huitt, D. K. Lowe

This laboratory flow study covers propping agent transporl in horizontal fractures as influenced by the characteristics of the propping particles, fluid and fracture. Correlations are presented for the transport of particles, deposition and fingering through dunes. For particles moving individually, the article velocity in some cases may be low compared to the hulk average fluid velocity; in other cases, the particle velocity may exceed the bulk average fluid velocity. At high propping agent concentration or low fluid velocity, the likelihood of particle deposition and dune formation increases. Fingering and channeling accompany dune formation. Dune formation can be limited to the outer region of tile fracture by adjustment of pump rate, fluid viscosity and particle concentration. A method is presented by which pump rate and fluid vircosity may he selected to control dune formation for given propping agent concentrations. INTRODUCTION The area and flow capacity of a fracture predominantly control the stimulation derived from hydraulic fracturing. Generation of fracture area exposes the rock matrix to a flow channel; the flow capacity of the fracture controls the flow through the channel to the wellbore under a given pressure gradient. This paper pertains to an important factor that affects the flow capacity of a fracture: the transport of the propping particles in the fracturing during the hydraulic fracturing treatment. With a better understanding of particle transport, fracturing treatments may be designed to obtain more effective distribution of the propping agent. RELATED STUDIES In recent years, the approach to obtaining high fracture flow capacity has been partial monolayer propping. Three papers1-3 have dealt with various facets of this concept. However, in some papers dealing specifically with particle transport, the results generally indicate that packing the propping particles within a fracture is inevitable. In early work&apos; with a sand slurry flowing in a pie-shaped flow cell, qualitative results showed that particle deposition in a fracture during transport should be expected. In other studies"" correlations based on slurry flow in vertical linear flow cells showed particle deposition was primarily a function of fluid velocity. In a recent paper the rate of sand advance (movement of dunes) in a horizontal linear flow cell was discussed. Subsequently, a method was given for designing fracturing treatments, based on the extent of sand advance during a treatment. In this work, particles whose diameter was small relative to the fracture width (i.e., dl W< 0.2) were primarily considered. The particle transport approaches that of sand transport in a stream bed. The industry trend, however, has been to use larger size propping agents. That is, particles with diameters approaching fracture widths predicted by Perkins and Kern.&apos;&apos; This trend has led to generally better fracturing treatments with particle relative sizes in the range 0.2 <d/W < 1.0. In all of the particle transport studies previously cited, the fluid characteristics were discussed. However, little or no attention was given to the parzicle characteristics. In this study the particles. as well as the fluid and fracture, are considered. VARIABLES AFFECTING PARTICLE TRANSPORT In the exploratory work to set LIP a program for this study, it was noted that particles within a batch moved at different velocities in a horizontal linear flow cell. In some cases the particles moved independently. In others there was particle interference. Also, particle deposition and fluid fingering occurred in some cases (Fig. 1). As a result of observing the easily distinguishab&apos;le types of particle movement, the particle variables as well as the fluid variables were included. In addition, the fracture width was included because the fluid velocity profile surely must affect the movement of the larger particles differently than that of smaller particles. Particle variables were density, diameter (based on a sphere of equal volumetric displacement), long and short dimensions, drag coefficient and velocity. Fluid variables were density, viscosity, yield shear strength and velocity. Fracture variables were the width and the angle between the plane of flow and a horizontal plane. Two factors which may prove to be important were omitted because of the complexity resulting from the parameters cited above. These are the fracture-surface roughness and gross irregularities that cause changes in the direction of flow. EXPERIMENTAL EQUIPMENT AND PROCEDURE A linear parallel-plate flow cell (Fig. 2) was used in the study. Lucite plates 1 in. thick formed the test section and permitted a viewing section 11 ft long and 10 in. wide. Spacing between the plates was adjusted with shims to give fracture widths 1/36 to 1/2 in. The model could be tilted to an angle of 45" with the horizonltal plane. Fluid flow was maintained with a Moyno positive displacement pump. Single particles were placed in the flow stream with a particle injector. A .4 - in. diameter plunger moving at a constant rate in a

Jan 1, 1967

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world&apos;s produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world&apos;s demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world&apos;s barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

Mining and Metallurgy of Lead and Zinc, AIME Vol. 121, edited by Dr. C. R. Hayward in 1936, remains a document of importance today even though 34 years have passed in the meantime. Since nothing in this world seems to be permanent, however, and progress brings new and better ways to do things, a two-volume set has just been published to bring the state of the art of 1936 up to date. This two-volume set, Mining and Concentrating of Lead and Zinc and Extractive Metallurgy of Lead and zinc, incorporates the papers to be presented during the Proceedings of the 1970 World Symposium on the Mining and Metallurgy of Lead and Zinc. The Symposium is being held October 20-24, 1970, in St. Louis, a site near to the famous Lead Belt of southeast Missouri. Some eighty papers are bound in these two volumes covering exploration, geology, mining, concentrating, roasting, smelting, electrolytic processing, residue fuming, refining, etc. All of this is laced with data on tonnages, processes, assays and efficiencies obtained, and the man-hours and equipment needed to achieve these performances.

Jan 1, 1970

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

Aamot, Olav Crone, (M&apos;29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M&apos;3S) Min. Engr., Dir., Bu¬ reau of Mines. Manila, P. I. Abbott, Agatin Townsend, (J&apos;40) Jr. Engr., Phelps Dodge Corp., Morenci Branch, Morenci. Ariz. Abbott, Clarence E., (M&apos;04) Civil Engr., V.P., Ten¬nessee Coal Iron & R.R.. Co., 1542 Brown -Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M&apos;28) Chem. Engr., Command¬ing, Officer, Pittsburgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D., (M&apos;32) Alin. Engr.. Div. of Cor¬porations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M&apos;31) 423 3rd Ave., Decatur, Ga. Abell, Leo M., (M&apos;31) Mill Supt. & Met., Emperor Gold Min. Co., Led., Vatnkoula, Fiji Islands. Abernathy, G. E., (M&apos;38) Geol., Kansas State Geol. Survey, Pittsburg, Bans. Abernathy, Jack H., (M&apos;40) Peer. Engr., c/o Superior Oil Corp., National Bank of Tulsa Bldg., Tulsa, Okla. Aborn, Robert H., (M&apos;10) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M&apos;39) Peer. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles, Calif. Abramowitz, William L., (J&apos;40) Chem., Industrial Inventions, Inc., 103 Foster Se., Peabody, Mass.

Jan 1, 1942