Search Documents

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

Research on the Thermodynamics of Siderite Roast Decomposition and the Experiment of Magnetic Roasting-Separation

Sep 13, 2010

Three large deposits of good quality lignite were located and delineated in the Central Otago region between October 1978 and July 1979. The program was initiated and funded by Mines Division of the Ministry of Energy as part of the national Coal Resource Survey. The exploration work was carried out by Lime and Marble Limited on a contract basis (Bowman, 1980). The three deposits were all potentially mineable by open cast methods and possessed combined indicated and, inferred reserves in the order of 1000 x 106 tonnes. They ranked with the previously discovered Eastern Southland 1ignites and as such constituted an important national energy resource. Fifteen months later a second more detailed investigation of similar duration was undertaken by the Liquid Fuels Trust Board (LFTB). The objective was to upgrade and refine the geological data base of all of the nine South Island 1ignite deposits in order to make preliminary economic assessments of their potential. Again Lime and Marble Limited acted as the exploration operator (Bowman, 1981a, 1981b, 1981c).

Jan 1, 1983

By J. A. Finch, Zhenghe Xu

The competitive adsorption of xanthates on sulphide minerals in a binary mineral system (pentlandite and pyrrhotite) was studied using the pseudo-in-situ technique of attenuated total-reflectance FTIR spectroscopy. The minerals were placed in the same collector solutions, either separated by a glass wall or in direct contact with each other before magnetic separation and separate analysis. The effect of mineral interaction on xanthate adsorption was clearly demonstrated spectroscopically for the first time. At low concentrations of xanthate, its adsorption on pentlandite was activated by physical contact with pyrrhotite; the effect may be attributed to the enhancement of electron transfer through electrical contact between the two minerals. The results emphasise the need for caution in extrapolating results obtained from single-mineral studies to flotation practice

Jun 18, 1905

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

By A. A. Paoli

The selection of a mining plant for carrying on development work presents many problems distinct in themselves, and affected by various local factors. In this paper, the writer proposes outlining and discussing in some detail the chief factors governing the economic selection of such plants. This will be followed by an enumeration of the underground and surface plant required for carrying on several hypothetical exploratory and mining operations. Where it is impossible or not convenient to obtain hydro-electric power, and where wood for fuel is scarce, we now find oil engines being used. A 100 h.p. oil engine, such as would be required to operate a three-drill air compressor, consumes approximately five Imperial gallons of fuel-oil per hour at full load. On the basis of a 60 per cent load factor, this gives, for eight hours' operation, a probable actual consumption of twenty-four Imperial gallons.

Jan 1, 1929

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Mines investigation of the more economic utilization of the so-called "black oils" of Wyoming. This problem is being studied by the Bureau of Mines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station , Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oils has been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), and the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black- oils; it was thought t that a more fundamental attack would assist-materially in, the problem of sulfur removal.]

Jan 1, 1941

By J. A. Every-Brown

Case studies are presented of three derelict sites in Kent and Essex that provide a good cross-section of opportunities for second-generation commercial uses of former chalk, limestone, clay and gravel workings. A 240 ha abandoned chalk quarry at Grays in Essex, now known as Chafford Hundred, is undergoing mixed development to include leisure facilities, a range of housing and commercial areas and an enhanced environment. The 120 ha of Stone Marshes now comprises the Crossways business park and the Dartford international ferry terminal. Reclamation and servicing required more work than had been anticipated and the fact that the area was within the green belt added to the delays, but Blue Circle was eventually able to provide a comprehensive development of the entire area to a high environmental standard. Stone Pit 1 landfill, at Dartford in Kent, is a former chalk quarry 40 ha in area and with an original average depth of 35 m. Landfilling commenced in 1976 and during the period 1979-1984 the site operator designed, developed and installed a gas collection and flaring system. From 1986 a gas plant supplied up to 5 000 000 therm/yr of landfill gas to a local cement works and in 1989 a 1 MW power generation scheme, later expanded to 3 MW, was commissioned. Gas is currently also supplied to a metal refining company for use in internal combustion engines

Aug 1, 1994

By A. Sheikh, S. Hardcastle

"Various methods of leaching are being used by Denison Mines Ltd. Uranium Operations. This study was designed to investigate the flood leaching operation of two parallel inter-connected stopes contained by pressure bulkheads. The teaching muck piles, created from large scale uppers production blasts, are aerated by compressed air lines laid beneath the pile prior to blasting.A SFr, tracer gas, injection technique has been employed to determine the post-blast integrity of the single-ended air distribution system. SF6 was injected into the compressed air line feed to the stopes and collected at borehole exhausts from the stopes in grab-sampling bags. Analyses of the air samples were performed with a gas chromatograph.The system was designed to give a sufficiency of oxygen to sustain bacterial activities used to enhance the leaching recovery in the muck piles. The results obtained indicated that there is a minor anomaly in the distribution system that may not be critical to the operation. Compared to an idealized case, the over-all efficiency of aeration throughout the muck is estimated at over 85%."

Jan 1, 1988

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Nines investigation of the more economic utilization of the so-called "black oils" of Wyoming,. This problem is being studied by the Bureau of Nines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station, Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oilshas been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), end the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black oil, it was thought t that a more fundamental attack would assist materially in the problem of sulfur removal.]

Jan 1, 1941

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

By K. Lim, J. Sobil, L. Galarza Castillo, F. Tozlu

"For mining operations globally, the scale and criticality of the grinding mill drive has meant that selection of the correct mill drive technology is paramount. With so much depending on the successful implementation of the electrical drive system— safety operation, timely installation, availability, energy efficiency, minimum maintenance and extend its use as tool to assist during mill liner exchange—customers are justified in their scrutiny and slow adoption of new drive technology. From the first installation of low, fixed speed synchronous motors to the introduction of the current source and further voltage source variable frequency drive, innovations require long periods of time and mining customers willing to push the industry forward. In recent years, the variable frequency drive has been the stepping stone for a new generation of mill drive technology. In use for decades in other heavy industrial applications, the drives allow for system optimization in a myriad of ways. The most dramatic of changes is in the design of the motor. Where in the past motor design was bound by line frequency, today the designer can optimize machine size and, more importantly, eliminate the need entirely for the synchronous motor. Induction motor design has now progressed to the point where low speed operation is possible at efficiency levels nearing those of the synchronous design. Moreover, the simplicity of the squirrel cage design means that availability, reliability and spare part requirements are greatly improved. As the next step in the evolution of large pinion driven grinding mills, the low speed induction drive offers a new reliable and robust system to the market.IntroductionAs deposit grades continue to decline, new ways of processing ever greater concentrator throughputs have been required to maintain throughput efficient and profitable operations. Furthermore, the high risk nature of mining developments requires a constant search for safer, higher availability and more efficient equipment design. Limitation of downtime is a key factor in ensuring mining operations can be sustained through volatile market conditions. Often processing the entire mine throughput through just 1 or 2 lines, the crushing and grinding circuits are of particular criticality to the uptime and, thus, profitability of any mining operation."

Jan 1, 2016

By Wayne Burmeister, Danie Benade, Louis Meyer, Hugo Joubert

What is not measured cannot be managed. This is true of most things, including a furnace lining. This paper describes a Lining Management System used for this purpose. It provides the operations staff with a management tool to predict long term lining life and acts as a process optimisation tool. It alarms and records upset furnace conditions. Outputs from the system are described as presented through a specially developed software package and interface. It includes vertical and horizontal furnace sections showing estimated isotherms through the lining as well as the furnace bath. It also shows calculated heat flux values, estimated lining wear and the freeze layer profile. A novel three-dimensional display is described which provides the operator with a big picture view of the furnace crucible profile under real time operating conditions. The powerful trending facility for analysing both measured and calculated values is discussed. The required instrumentation hardware as well as the installation thereof is described, with special reference to an electrically insulating thermocouple socket design. Finally feedback is provided on the first year?s performance of the system installed on an open ferrochrome furnace at Assmang Chrome, Machadodorp, South Africa.

Jan 1, 2007

By P. C. Holloway

La Oroya zinc ferrite (19.5% Zn, 26.6% Fe, 0.052% Ga, 0.075% In) was roasted with coal under conditions more oxidizing than normally used in a Waelz kiln, and the roasted residues were leached with 200 g/L H2SO4. Overall zinc recoveries of up to 97% were achieved, with 35% of the zinc reporting to the fume after roasting at 1,100°C with a bituminous coal addition of 20%. Under these conditions, 93.2% of the Cd, 13.4% of the Cu, 33% of the Ga, 61% of the In and 18.2% of the Pb were recovered either in the fume or in the leach solution. At 2006 metal prices, the value of the recovered metals is comparable to that obtained from commercial Waelz kiln processing of this residue. Zinc in the franklinite (ZnFe2O4) mineral is reduced to zinc vapor, and, after oxidation, some of the zinc is found as ZnO or as Zn2SiO4 in the roasted residue. Iron reacts to form either hematite (Fe2O3) or magnetite (Fe3O4), with no metallic iron detected in the roasted residue, and less than 2% of the iron is solubilized during leaching. The residue produced after roasting and leaching is, therefore, much more stable than the residue from Waelz kiln processing and should be suitable for disposal in a landfill.

Jan 1, 2008

By H. T. Ozkahraman

It is important to know the breakage mechanism in materials since this knowledge influences the results of subsequent grinding operations. There are two distinct failure mechanisms in breakage: one is tensile micro crack generation at low stresses, which leads to macroscopic failure by disintegration, and the other is formation of shear zones under heavier dynamic impact forces, which generates more fines as seen in crush zones in blasting. Tensile fracturing simply breaks the material into fragments. It is seen as the disintegration of the specimen into two or more separate fragments. This happens under the absence of lateral stresses and the material is free to expand. On the other hand, compressive-shear breakage produces finer fragments due to shear stresses. The first mechanism is observed in laboratory tensile and bending strength tests and the second mechanism is observed both in laboratory brittleness tests and in situ blasting operations under dynamic impact forces. The friability of rocks and ores can be determined by a brittleness test. A test apparatus to determine the friability value has been designed to suit limestone strength characteristics used in cement production. The friability and stored strain energy values of barite, marble, limestone and bauxite have been determined and compared with the corresponding Bond work index (Wi) and grindability index (G) of these materials. The physico-mechanical properties of the tested materials have also been determined to investigate their effect on friability and grinding. The relationships obtained between the indices were in surprisingly good agreement, with high correlations (0.99 and 0.97). The Bond work index and grindability index can therefore be estimated from the friability value, which can be determined more rapidly than the Bond test. But for certain rock types such as andesites the relationships does not hold. Key words: comminution, tensile stress, shear forces, brittleness test, strain energy.

Jan 1, 2010

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961