Search Documents

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Due to the difficulties of ventilating large opening stone mines, the effective dilution of diesel particulate matter and noxious gases has often been problematic. Since stone mines have large openings that develop low air resistances, and propeller fans are designed for low pressure-high volume applications, main mine propeller fans may be a feasible option for ventilating underground stone mines. This paper describes the results of a case study where researchers from the National Institute for Occupational Safety and Health have demonstrated that significant increases in total mine airflow can be achieved and the ventilation improved in a large-opening stone mine by replacing an axial-vane mine fan with two 12-ft diameter propeller fans and adding a line of stoppings. In this study, the use of the propeller fans more than doubled the air quantity from 300,000 cfm to 750,000 cfm, while operating at 50 horsepower less than the original axial-vane fan.

By M Rafty, A Markham, S Atkinson, M Heyting

Over recent years there has been a significant increase in the number of miners in the Pilbara region of Western Australia targeting channel iron deposits (CID) located in valleys, intersected by ephemeral creeks and below the groundwater table. The falling iron ore price has triggered a drive to reduce cost and maximise yield. Creek diversions provide an opportunity to maximise the utilisation of orebodies and extend the life-of-mine.Creek diversions that are required during mining operations to access ore and provide flood protection have historically been constructed as uniform engineered channels designed primarily for flow conveyance while minimising earthworks costs; however, the design of diversions becomes more complex when they are required to function in a similar way to the existing creek system during operations and remain stable during more extreme events than would typically occur following mine closure, in accordance with current regulatory guidance. The design specifications for closure are often more rigorous than the operational phase, and could incur significant additional cost to implement retrospectively if not planned and designed upfront.The complexity of diversion design depends on site specific factors such as: the size of the creek to be diverted; hydrology; corridor restrictions; geomorphology; hydrogeology; geology; environmental and heritage values; potential impacts and the risk to operations and environment. The complex interactions of these factors must be well understood and hydraulic modelling undertaken to characterise the existing creek system, demonstrate the diversions, provide adequate flood protection during operations, and can function in a similar way to the existing system following mine closure. This paper presents key design considerations for Pilbara creek diversions, operational and closure requirements, mine planning considerations, risks, cost saving opportunities, and the benefits of an integrated approach to design.CITATION:S Atkinson, A Markham, M Rafty and M Heyting, 2017. ‘Back to the future’ – resilience in historical context and implications for the future, in Proceedings Iron Ore 2017, pp 367–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

This paper gives an overview of the difficulties associated with determining the strength of hard rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large scale pillar collapses in South Africa were caused by weak partings which traversed the pillars. Currently two different methods to determine the strength of pillars are used namely, empirical equations derived from the back analyses of failed and stable cases and numerical modelling tools with an appropriate failure criteria. Both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods are popular and easy to use, but care should be exercise that the results are not extrapolated beyond the range of the data which were used to derive them. An example is the Hedley and Grant formula (derived for the Canadian uranium mines) that has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value) to design the pillar layouts. Very few collapses have nevertheless been reported and it might even be too conservative an assumption of pillar strength in these mines. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many flawed assumptions. An area where numerical modelling is invaluable, however, is to study specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling currently provide a solid basis to conduct pillar design. It is therefore recommended that both these techniques be utilised when confronted with a pillar design to obtain the best possible insight into the problem.

Nov 25, 2010

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By Cooper R. J

The essential features of the zinc concentrate roasting installation at the Risdon Works by the Electrolytic Zinc Company of Australasia Ltd. are given.The problem of maintenance of ignition in down-draught zinc concentrate flash roasters is discussed, and a solution offered.A successful and economical method of using by-product oxygen for raising the roasting efficiency of hearth roasters is described. Three methods of utilizing oxygen for the same purpose in flash roasting are detailed, and their relative merit, considered.INTRODUCTIONThe zinc sulphide concentrate used at the Risdon Works is roasted autogenously for removal of sulphur in two hearth roasters, and four flash roasters. The hearth roasters are of modified Skinner type with eleven hearths. They were designed, and are used, for roasting mixtures of relatively low sulphide content. Their design and operation have been described elsewhere (Forster, 1949).The flash roasters are down-draughted furnaces with cross-section and rabbling equipment based on the hearth roaster design, and the process is similar to that developed by the Consolidated Mining and Smelting Company of Canada Ltd. (Cominco) at Trail, B.C. (Stimmel, Hannay, and McBean, 1936).These furnaces are 20 ft. in diameter. They have three drying hearths through which hot gas is drawn from the combustion chamber by the burner fan. The combustion chamber is 2'1 ft. high above the collecting hearth (27 ft. in No. 4 unit), and the discharge hearth below it is 6 ft. high, so that a large gas offtake is possible. Four rabble arms for each hearth are carried on a central column. Dried, ground concentrate, and the air for roasting it, are fed to a burner...

Jan 1, 1958

By V P. Elpatyevskaya, V S. Arzhanova

Main geochemical problems concerning the environment and mining industry interrelation are connected with the transformation of natural water chemistry by mining wastes. The investigation of many mines in Primorye, the southern part of the Russian Far East, showed that their mining waters have high concentrations of heavy metals and aluminium. Water acidity is primarily connected with the amount of acid-forming sulphide minerals in ores and also depends on the neutralising capacity of rocks. Considerable quantity of metals occur in the waters in dissolved form. Metal concentrations in mining waters exceeds the natural levels by two to five orders of magnitude and can't be reduced to the background levels even after multiple dilution. It is necessary to develop and put into practice new technologies so that to reduce the geochemical impact upon the environment.

Jan 1, 1995

By Greg S. Williams, Richard W. Givens

This paper examines the effect of prill size consistency, internal panicle density, and oil absorbency on Ammonium Nitrate Fuel Oil (ANFO)-emulsion blends. By analyzing these physical properties of prill and the nature of the blending process, a mathematical model has been developed to theoretically predict blend densities. Calculated densities can now be compared to actual field densities to give an operator a basis for comparing various manufacturers’ emssions and Ammonium Nitrate (AN) during bid solicitation. The lowest priced emulsion and/or AN may not be the most economical, due to the impact of specific physical characteristics. These factors dictate the blending mechanics and resulting density yields for various mixes. The research was driven from observed ‘field’ mixing relationships and data. Ultimately, such a model can be an effective tool in evaluating blends from a cost and performance basis.

Jan 1, 1992

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

By R. A. Williams

Electrical impedance tomographic methods have been applied to a variety of mineral and chemical processes in the laboratory and on plant. This review paper surveys technical developments in measurement methods to enable quantitative extraction of key process information in the form of mapping of concentration profiles, mixture homogeneity and suspension velocity. The methods for determining velocity are summarized, since this is of especial interest when applied to opaque systems where most conventional optically based measurements fail. A recent significant development is the use of ultra-high speed measurement that now allows velocity vectors to be extracted for fast moving mixtures and fluids (up to several metres per second). New data are reported pertinent to low and high solids concentration flow in pipelines. Use of the methods offer improvements to design of such systems but also points to the use of tomographic electrical sensor as online flow measurement and fault detection. This offers new opportunities for applications and benefits in the design and monitoring of mineral slurries and sludges.

Jan 1, 2008

By B Mohanty, M P. Roy, P K. Singh

"The measured response of residential structures is a critical indicator of troublesomeor potentially damaging ground vibrations. A study was conducted to evaluate theresponse of structures situated in the periphery of four open-pit coal mines in India. Although, most of the structures were at far-off distances from the present blasting sites, an attempt was made to document the response of structures to blast vibration for future applications to optimize the blast designs for the safety of the structures. The study involved a total 215 blasts, employing one-, two- and three-hole calibration study, and production blasts. The bench height varied from 7.5 m to 42 m, and boreholes loaded with emulsion and slurry explosives were 250, 260, 270 and 310 mm in diameter. The explosive detonated in a blast were between 300-198400 kg whereas in a delay it was 33-24800 kg. Up to 12 tri-axial vibration sensors were located in overburden along a linear array from 25 m to 6.5 km distance from the blasts. Altogether, 1512 blast vibration signatures were recorded. Production and specially fi red single-charge blasts allowed the determination of natural ground frequency. The fundamental frequency of the structures ranged between 3.13 to 10.6 Hz, the same as those of the ground vibrations. The amplifi cation of vibration in the structures was in the range of 1.6 to 5.6. The study details the interaction between ground vibrations and selected structures, and the means to reduce amplifi cation of vibrations in the structures and persistence of vibrations through improved blast design."

Jan 1, 2008

By R. M. Goktan

Rock brittleness plays an important role in the cutting action of picks on rock surfaces. It controls the ease with which cracks can propagate through the rocks. Although rock brittleness is known as a property that contributes to the cuttability of rocks, despite considerable research effort, there is still much uncertainty about the relation between rock brittleness and rock cutting efficiency. This fact can be attributed to the lack of a universally accepted brittleness concept and a brittleness measurement method. The existing publications of some researchers have, in a way, tended to confuse the understanding of brittleness in the general field of rock excavation where it is expected that the energy consumption of cutting should decrease with increasing brittleness of rock, other conditions being equal. However, this sometimes conflicts with the brittleness concept commonly used in rock mechanics, where the more brittle the rock the higher its mechanical strength. The ratio of rock compressive strength to tensile strength is considered by many authors to give a valuable brittleness index for drag pick operations. Hence, in this contribution the ratio of uniaxial compressive strength to tensile strength BI is considered as an index of rock brittleness, and a new methodology is proposed for its use in rock cutting efficiency analyses of drag tool operations. Validation of the suggested approach is supported by available experimental data in the literature. Contrary to the conclusions reached previously by other authors, it is shown that an increase in rock brittleness is accompanied by an increase in the cutting efficiency, other conditions being equal. Keywords: brittleness index, rock brittleness, cutting efficiency, specific energy, rock excavation.

Jan 1, 2005

By Hamid-Reza Manouchehri

Mining & Sustainability? A Paradox?! ? Production: gradually or exponentially increasing (giant mining) ? Ore Grades: gradually declining, ? Open Cut Mining: now widespread, likely to be sustained in the future though the long-term is hard to predict as new mineral deposits are likely to be deeper ? Waste Rock / Overburden: increasing rapidly, likely to be sustained in the future and closely linked to open cut mining, especially for coal and base metals ? Economic Resources: commonly increasing but some remain stable or gradually declining, future is linked closely to exploration, technology and economics; Increasing population, changing life style and technology development, ultimately result in sustainability in mining industry to hang in the balance and continue.

May 1, 2013

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

By S E. Munro, P D. Munro

The commonly traded base metals concentrates of copper, lead, tin and zinc are sold by miners to custom smelters using contracts whose terms were generally established at the beginning of the 20th century or even earlier. Technical clauses in these concentrates for items such as payable metals and penalty elements do not reflect current realities of extractive metallurgical technologies and hygiene/environmental issues.It is an axiom that the miners and smelters have a symbiotic relationship. While the existing antique and arcane commercial arrangements serve the purpose of transferring money from the buyer to the seller, they are not likely to result in the industry achieving better overall technical and economic outcomes. By examining the cases for copper concentrates and zinc concentrates in particular, it will be shown that the practical application of these antiquated technical clauses does not drive the miners to produce the better quality concentrates that should be desired by the smelters. This is despite development of mineral beneficiation and hydrometallurgical technologies that would allow the miners to make better products.The adage that any extractive metallurgical problem in the smelter is cheaper to solve in the concentrator still generally holds.While nickel concentrates are only touched on lightly in this discussion because sales terms are more opaque than those for the other base metals, it is expected that the same conclusions will apply.CITATION:Munro, P D and Munro, S E, 2015. Base metals concentrate sales contracts – change Pavlov and the dog, in Proceedings MetPlant 2015, pp 46–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015