Search Documents

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4010(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mobs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyro-phyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constitu-ents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 percent and the alumina from 22 to 33 percent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent.

Jan 1, 1940

By Arnaud Faucher, Claude Bazin, Marilène Renaud, Mohamed Mai Manga

"Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action needed to minimize its impact on the process. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality. Recovery losses in downstream leaching or flotation circuits justify the effort in developing techniques for the detection of hydrocyclone malfunction. Two approaches for the detection of hydrocyclone fault are presented in this paper. The first proposed method uses the conventional sensors available in a grinding circuit allowing real time detection of hydrocyclone abnormal operation. The second technique is based on the use of vibration sensors installed on the hydrocyclone of a nest. This last technique enables the classification of the hydrocyclone malfunction as surging, overloading and plugged apex. The two techniques can be combined to increase the robustness of the problem detection.INTRODUCTIONHydrocyclones are used for many purposes ranging from water separation, fines removal and obviously for the preparation of the feed for subsequent concentration circuits in a mineral processing plant. The strategic role of the hydrocyclones for the preparation of the feed to the concentration circuit is often underestimated because of their simplicity of operation and robustness (Napier-Munn et al., 1996; McIvor, 1988). It remains that despite their simplicity, hydrocyclones have been studied extensively from 1970 to 1990 with the objective of developing mathematical models of their operation to be incorporated into grinding circuit simulators (Napier-Munn et al., 1996; Lynch, 1977; Flintoff et al., 1987). Such a development effort is already an acknowledgement of the importance of these units in a mineral processing plant. Several authors (Del Villar et al., 1996; Plitt and Kawatra, 1979; Casali et al., 1998) proposed soft sensors to estimate the classification efficiency of hydrocyclones using sensor measurements. However, few of the proposed sensors are used in the industry. More recently several papers were published to discuss the application of 3-D modelling of the hydrocyclones (Narasimha et al., 2005; Cullivan et al., 2004) and sensors (Bond et al., 1999; Neesse et al., 2003; Hou et al., 1998; Olson and Waterman, 2004; Williams et al., 1995; Willams et al., 1997) to help in the detection of hydrocyclone malfunction."

Jan 1, 2010

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

In this, the centennial year of The Institute, it is appropriate that the history of the Institute in New Zealand be recorded. I am indebted to John Dew, compiler of the centenary publication æMining People A Century - Highlights of the First Hundred Years of The AusIMM 1893 - 1993Æ, for many of the early historical references in this paper. In July 1892 the Amalgamated Mining Managers' Association of Australasia held its annual conference in Ballarat, Victoria, Australia, when it was suggested by the delegate from Broken Hill that the time had arrived for the establishment of an Australasian Institute of Mining Engineers. Resulting from this meeting at Ballarat, a Provisional Committee was formed at Broken Hill with the object of forming The Australasian Institute of Mining Engineers having the following objectives. To promote the arts and sciences connected with the economic production of the useful minerals and metals, the welfare of those employed in those industries by means of meetings for social intercourse, and the reading and discussion of professional papers with the circulation by means of publications amongst its members and associates the information thus obtained.

Jan 1, 1993

By Fabio do Prado Verderano

A partir de corpos de prova de uma chapa de aço baixa liga NBR 6656 grau LNE 26, realizou-se a caracterização microestrutural, levantamento do perfil de dureza ao longo da espessura da chapa, ensaios de tração monotônicos, cíclicos de fadiga e análises fractográficas. Concluiu-se que, nas extremidades da espessura da amostra, o valor da dureza é maior, indicando que quando a chapa foi laminada as superfícies em contato com os rolos de laminação sofreram encruamento, aumentando a dureza nessa região. A microestrutura encontrada e o grau das inclusões presentes na amostra são compatíveis para o material, bem como as propriedades mecânicas monotônicas, que estão de acordo com a especificação. Por meio de ensaios de fadiga de baixo ciclo, encontrou-se uma boa correlação entre as propriedades monotônicas e cíclicas do material para a proposição da equação de Basquin, considerando-se dados seguros, quando utilizado os primeiros vinte ciclos do ensaio de fadiga para estabilização de cada corpo de prova. Verificando-se a seção transversal da fratura do corpo de prova, observa-se que o mecanismo de falha do material ocorreu a partir do aparecimento de trincas na interface ferrita-cementita com propagação transgranular até a fratura final.

Aug 17, 2017

By H. C. George

This bulletin deals with prime movers, power-transmitting machinery, and the surface equipment and methods used to pump oil wells. It does not discuss geological problems nor the methods and equipment used in drilling or at flowing oil wells. Much of the presentation is by photographs and drawings which are described in the text. Underground equipment and methods for pumping oil wells will be discussed in a later publication of the Bureau of Mines.

Jan 1, 1925

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Energy dissipation and fragmentation of rock is of interest for mine-to-mill operations in order to understand breakage and to minimize energy consumption during blasting at the mine site, and comminution at the processing plant. In this regard, high velocity impact breakage of long granite cores, called bars, has been studied with instrumented strain gages to follow the energy dissipation gradient along the bar length resulting from the strain waves generated by impact. As a result of high velocity impact, three zones have been identified (fragmentation, fracture, and elastic) and these three zones have been characterized in 3D using X-ray tomography. The fragmentation zones of the granite bars were studied in detail to describe the particle size distribution and the particle shape characteristics. Finally, the experimental energy dissipation for the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work equation, if the anisotropic granite particles are defined by length rather than by sieve size.

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Energy dissipation and fragmentation of rock is of interest for mine-to-mill operations in order to understand breakage and to minimize energy consumption during blasting at the mine site, and comminution at the processing plant. In this regard, high velocity impact breakage of long granite cores, called bars, has been studied with instrumented strain gages to follow the energy dissipation gradient along the bar length resulting from the strain waves generated by impact. As a result of high velocity impact, three zones have been identified (fragmentation, fracture, and elastic) and these three zones have been characterized in 3D using X-ray tomography. The fragmentation zones of the granite bars were studied in detail to describe the particle size distribution and the particle shape characteristics. Finally, the experimental energy dissipation for the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work equation, if the anisotropic granite particles are defined by length rather than by sieve size.

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By W. F. M. GOSS

For the purpose of procuring data that could be used in estimating the value of the briquetting process as applied to American fuels, the United States Geological Survey, in cooperation with other interests, began in 1904, at the Louisiana Purchase Exposition, certain experiments involving the production and use of bituminous-coal briquets. It installed at St. Louis, and later at Norfolk, machines for the manufacture of such briquets, and the output of these machines has been tested in locomotive service on several different railroads in comparison with natural fuels. An elaborate and carefully executed series of tests involving the use of natural coals and of briquets made from the same coal, previously crushed, was carried out on a locomotive mounted at the testing plant of the Pennsylvania Railroad Company at Altoona, Pa.; and some preliminary experiments involving the use of briquets in marine service were made in connection with one of the Government's torpedo boats. A description of these tests is presented herewith. The results sustain the following general conelusions: 1. The briquets made on the Government's machines have well withstood exposure to the weather. and have suffered but little deterioration from handling. 2. In all classes of service involved by the experiments, the use of briquets in the place of natural coal appears to have increased the evaporative efficiency of the boilers tested. 3. The smoke produced has in no test been more dense with the briquets than with coal; on the contrary, in most tests the smoke density is said to have been less when briquets were used. 4. The use of briquets increases the facility with which an even fire over the whole area of the grate may be maintained.

Jan 1, 1911

By B. Caro Vargas

The Toulon Tunnel project is a key component of the highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960s. The tunnel project is comprised of two separate tunnels: south and north. The north tunnel was built between 1992 and 2002 after 10 years of difficult construction. On March 15, 1996, for example, a collapse of the tunnel in the Marchand area generated a sinkhole in the city center, causing a 20-month delay. The south tunnel alignment runs parallel to the north tunnel below Toulon?s historical downtown at a depth of 20 to 40 m (65 to 131 ft) with some areas with less than 10 m (32 ft) of cover. The risk management program was studied to be a state of the art program in urban tunneling construction.

Jan 1, 2012

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

The acid plant consists of the following units: 1. Glover tower. 6. Mills-Packard type chambers. 3. Reaction towers. 6. Gay-Lussac towers.The sulphur dioxide bearing gases, used in the manufacture of the acid, are obtained from the roasting of zinc concentrate. Six Herreshoff type furnaces are available, each with an effective hearth area of 520 sq. ft.The concentrate contains approximately 30% sulphur, of which about 72 is ultimately recovered as acid. The oxides of nitrogen are added to the gases in the requisite proportions partly from nitrous vitriol and from nitric acid in the Glover tower, and partly from nitrous vitriol in some of the chambers and connecting flues.The acid leaving the Glover tower is cooled by the ordinary water-cooling coils, while the cooling of the chamber gases is effected by circulating water over the outer surface of the chambers, and by spraying nitrous vitriol and weak acid into them.Flow of gases throughout the plant is regulated and controlled by means of regulus metal fans, fitted with variable speed gears.

Jan 1, 1934

Local conditions at Hatches Creek are described, together with the mineralogy, mining and treatment of tungsten ores, with particular reference to procedures adopted by Pimer Mines, N.L.The Hatches Creek tungsten field covers an area of about 20 square miles in: Central Australia; 285 miles' N.E. of Alice Springs. Access is by rail to Alice Springs, then by 200 miles of bitumen highway to Barlo Creek and 8,5, miles of bush track to the field. Passengers can also reach the mines by... A semi-desert climate prevails Rain; generally in the form of thunderstorms falls in the summer months: December to March. Average annual rainfall is approximately 15 inches but there is great variation from year to year, occasional droughts being followed by torrential downpours. Vegetation is sparse except in the wide creek beds. Surface water occurs in rock holes some of which, spaced miles apart, carry permanent water...

Jan 1, 1955

By R. W. Stahl

Employees and dollars are necessary to all enterprises and any force, such as fire, which destroys either, can bring very serious consequences, including business failure. Since everyone acknowledges the necessity of conserving human life, we will devote most of our paper to the economic factors involved. A coal-mine fire is considerably more difficult to combat than a fire in a surface building because of the combustible surroundings in the mine, the explosive gases emitted from the coal, the suspension of explosive dust when mine timbers burn and the unsupported roof falls, the limited space in which approach to the fire can be made, and the limited avenues of escape. A survey of coal-mine-fire protection indicated that a rather low value was being placed on property and equipment. This prompted comparison with other industries. The comments made in this comparison are not intended as an indictment of the coal industry, since we do have mines that are well protected against fire, but the comments on conditions at the mines visited are factual and may help others to improve similar conditions. SURVEY PROCEDURES Plants of the steel, aluminum, rubber, chemical, and petroleum industries were surveyed, and all facets of the fire-protection scheme were covered. The industrial plant invariably had four times as much water readily available for instant use than the mine. In many mines where water is available, no equipment for applying it is provided, such as hose, nozzles, and adapters, so that time is lost in collecting this equipment. (See Table I.) EXTINGUISHERS Many more and generally larger portable extinpishers are available at the plant as compared to the mine. The extinguishers are generally placed nearer to sources of danger. In addition, respiratory protective equipment is always available at strategic points in plants but only in a few mines. (See Figs. 1 and Table 11) INSPECTING AND TESTING EQUIPMENT Plant water facilities are checked weekly and flushed at 6-month intervals, and hose is pressure-tested at least yearly; some mines check water yearly, but hose is not tested unless used. Fire extinguishers are inspected weekly in plants and completely overhauled yearly; one mine had monthly checks and overhauls only after use. FIRE BRIGADES AND TRAINING Every plant had designated fire-fighters and some complete full-time brigades; at one mine a chief mechanic was designated as being in charge of fires, and other depended entirely upon officials who might not be familiar with the equipment. COST OF FIRES AND PERCENTAGE OF CAPITAL INVESTMENT IN FIRE PROTECTION The direct cost of recent mine fires ranged from $128,000 to $240,000; indirect costs, such as lost tonnage, idled equipment, lost orders, and the like might run the cost to over $500,000. (See Figs. 2 and 3).

Jan 1, 1961

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By M J. Kongas, K M. Saloheimo

This paper presents the art of on-stream particle size and elemental analysis used at iron ore concentrators, followed by the results and experiences from several sites.Online particle size analysis is rather common at medium- to large-sized concentrators. Online X-ray fluorescence (XRF) elemental analysis, however, is only used in some iron ore concentrators, while it is a routine practice in base metal concentrator plants. Online XRF analysis is applicable for process monitoring and control down to four to five per cent silica by measuring Fe assays accurately. With lower silica content, direct measurement of silica and other light elements is required. Some light element analysers that are based on the prompt gamma neutron activation analysis (PGNAA) method have been developed, but they have not performed up to expectations with slurry analysis. Other methods have been tried though these have not been used beyond prototype installations. Operating online light element slurry analyser installations are not common in iron ore applications.There is an economic incentive to mine lower and variable grade iron ore resources, which require concentration and removal of several impurities to produce high-quality concentrates for pellet production. Monitoring such operations by on-stream analysis has significant economic benefits, and there is a need to develop a dependable slurry online analyser for Si, Al, Mg and other light elements. The latest developments in slurry on-stream light element analysis are described.CITATION:Kongas, M J and Saloheimo, K M, 2013. Online slurry analysis for process control and monitoring at iron ore concentrators, in Proceedings Iron Ore 2013 , pp 303-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J. L. Wiley

THIS REVIEW contains abstracts of the technical literature and patents dealing with the history, development, and commercial application of the Bergius and related processes for the hydrogenation, under greater than atmospheric pressures, of liquid and solid carbonaceous materials such as coal, lignite, their distillation and extraction products, pitches and tars, and petroleum and its distillation residues. An attempt has been made to include abstracts of all the published information on this process and of as much of the captured foreign documents and reports compiled therefrom as could consistently be reviewed during the time allotted for the work. Contact with the current literature and patents and review of the foreign documents will be continued and the information will appear in Synthetic Liquid Fuels Abstracts, which is being issued bimonthly as a Bureau of Mines publication. The material in this review is divided in two sections-literature (part I) and patents (part II)-and each of these is arranged alphabetically by author or patentee with further chronological arrangement under each author or group of authors. Secondary authors and patentees as well as assignees are cross-indexed to the main entry. In serial articles or reports the complete series appears in the alphabetical arrangement according to the author of the first member of the series. Succeeding members as well as secondary authors are entered as cross references; Titles of the journals are used as the authors in anonymous references. By following such a procedure, an author index is not required. However, a detailed subject index and a numerical patent list by countries are given as part III.

Jan 1, 1950

Taking the third meridian as the eastern boundary of proved payable auriferous country, there is a stretch of country, nearly 600 miles in width, in which no appreciable amount of gold has yet been discovered. Many prospectors have attempted to .penetrate or traverse it, but comparatively few have thought it worth while proceeding with the examination.The desolate stretch of waterless desert-the very few and insignificant outcrops through the sand and the almost total absence of feed for horses have, combined, presented such a barrier as to preclude prospecting. The few who have traversed the country are eloquent in denunciation, yet their investigations, necessarily hurried, are not quite satisfactory. The absence of water utterly debars a thorough examination being made. Gold may exist in quantity, yet it would have to be extraordinarily plentiful to render its obtaining profitable. Too fantastic is the idea of its ever being a mining district; shifting sand to traverse, utter absence of wood and water render the notion absurd. Likely looking belts occur, but these in all "cases are small and remote from water. Gold has been obtained from likely look ing quartz reefs, but only by fire assay, and then but a few do to the ton. Without wishing to be pessimistic, I would unhesitatingly declare that east of the third meridian, and between the parallels 25 and 30 degrees in West Australia, there is no gold in payable quantities.

Jan 1, 1901

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015