Search Documents

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

The low production rates associated with the underground metal mining industry have received considerable attention during the last decade. A number of significant technological advancements, in the form of new equipment, have taken place to improve the economics of ore production. Unfortunately, an extremely important factor in the equation -- the operator protection and safety -- continues to receive a low priority. The underground metal mining industry has one of the poorest industrial safety records in the United States. Equipment operators are constantly being placed in hazardous situations. Even one fatality is one too many. All of us bear the responsibility to eliminate it. This project is one of the important steps currently being undertaken by the U.S. Bureau of Mines to improve the operational safety of seven major pieces of ore handling equipment commonly used in underground metal and non-metal mines. The objectives of this study are; (a) to identify the existing hazards associated with the operation of the specific equipment, and (b) to recommend practical solutions that will minimize these hazards and reduce operator injuries. These recommendations are to be in the areas of equipment design improvements, additional operator protection and warning devices, equipment operating procedures and any modifications to the existing safety regulations.

Jan 1, 1975

"Guests and Members of the Rocky Mountain Coal Mining Institute: "It gives me a great deal of pleasure to call the Fifty-Second regular meeting to order this morning. "I think that you will agree with me that we have an excellent program planned for the next three days, comprising various interesting and educational subjects by authors of prominence, which will be of keen interest to all of us in the coal industry. "The Program Committee, chairmanned by John Peperakis, has done an excellent job in securing this very splendid talent for our convention. "I would like to say a word as to the, condition of the coal industry in our part of the country as well as elsewhere. I believe we can look at it with more optimism than in the past several years, particularly in the state of Colorado, with which I am more familiar. "Annual coal production in Colorado gradually dropped from around 12 million tons during the years of World War I to as low as 8 million tons during the last war, and to less than 3 million tons in the year of 1954. We believe that it touched bottom that year, as in 1955 the state production went up again to nearly 3,400,000 tons, equivalent to an increase of 15%. As you know, the national increase in bituminous coal production for the year of 1955 was roughly 2000 over 1954. "The national increase for the first two months of 1956 over the same period of 1955 is approximately 2100. Colorado's production is running around 1000 over the comparable period of last year, and the 5 states represented by our Institute came up with a nice increase in 1955 over 1954 of 1000. "Figures on the increase so, far in 1956 for this group of states are not readily available, but I fully believe that. our industry locally, as well as nationally, is now starting out on a steady rise despite the fanfare of nuclear energy and its more glamorous competitor, solar energy. Many authorities tell us that real competition from these sources is a long way off and that the atomic energy program will consume far more coal than is displaced by nuclear power. "I do not mean to infer that we coal people are out of the woods by a long way' so far as holding and regaining markets, for our coal. The captive operators, which are well represented here, have not lost their market for coking coal, since coke is still a necessary

Jan 1, 1956

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By G. Warren

"In the past, smelting and refining of the precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. This philosophy is changing however, as economic and environmental pressure are forcing a re-evaluation of all aspects of gold mining and milling.This paper describes and evaluates three furnace technologies available and used by precious metal operators. The operation of arc, induction, and reverberatory furnaces are discussed and their strengths and weaknesses with respect to capital cost, impurity removal, slag quality, and environmental concerns highlighted.INTRODUCTIONIn the past, smelting and refining of precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space, and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. Generally, gold producers will spend a great deal of effort to squeeze the last drop of efficiency out of a leach or grinding circuit via simulation or testwork but will design and build the refinery based upon past practices or industry standards. That past practices or industry standards will provide a functional refinery is undisputed; that this philosophy achieves the efficiencies that are possible or demanded in other plant operations is debatable.Environmental and worker hygiene requirements are considerations as well. Pollution control equipment can become a substantial contributor to both the capital and operating costs of a refinery and furnace selection has a marked influence upon the type and cost of this equipment. Slag characteristics and subsequent processing options available also play a role in furnace selection as precious metal slag losses and the recovery effort can greatly influence the cost / benefit analysis of a particular technology."

Jan 1, 2001

By Adam Powell, Matthew Earlam

INFINIUM, Inc. is scaling up a new molten salt electrolysis process for producing rare earth metals. Instead of conventional carbon anodes, this process uses Pure Oxygen Anodes™ which employ a stabilized zirconia solid electrolyte between the molten salt and anode. This eliminates two problems with today's rare earth metal production technology. First, it eliminates carbon anodes and contamination of the product by carbon and its impurities, enabling 10-100 times larger batch size than current practice, and lower labor costs. Second, it eliminates emissions of perfluorocarbons (PFC) such as CF4 and C2F6, which are very problematic greenhouse gases with 6000+ times the global warming potential of CO2. The zirconia also enables a sealed vessel with no LiF emissions, creates a reducing environment enabling use of low-cost welded steel vessels, and either produces a high-purity oxygen by-product or can use natural gas to reduce the necessary electrical energy with no HF production. This paper will describe the technology and its current status for rare earth metal production.

Jan 1, 2014

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of more accurate detonators. The new and more accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1986

By Earl S. Greiner, Eric R. Jette

ALTHOUGH the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data on the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face- centered cubic (gamma) phases, and the alloys containing from 24 to 100 atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt. per cent Si).* The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,5 who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by Osawa and Okamoto.6

Jan 1, 1943

By H. B. Humphrey

[EXPLOSION of gas and dust in coal mines, have caused death t lid injure to mines, and destruction of workings in all countries where coal is mined underground. In the United Stales the first reported explosion wits in Min; explosions have continued to the present. The danger to film ill it mine When an explosion occurs in not always measured by the violence created or by their nevi lies, to the area through which flame and Violence extend. As many, perhaps more, risen have died from gases and lade of oxygen (known as "after-damp") than have been killed by the blast and hart. Me explosions often are caused by it combination of factors, including concentration of methane in air, formation of clouds of dust, and the presence of a flame or spark. These explosion factors have varied with changes ill milting method and practises over the years, but the basis causes have always been the salve. Understanding of the causes and to acceptance of ways to guard against explosions and their effects have been slow to spread from investigates to officials and Own to bosses and miners. To a considerable extent there hats lawn a belief that explosions were a joining risk but might hr, put oil hut could not be presented. Such belief is based on the human failure to maintain and observe necessary precautions. These failures, caused by inertia to change, carelessness, or reliance on continuance, of past explosion-free years, are being reduced in number and effect by education of miners and supervisors and acceptance of higher prevention standards.]

Jan 1, 1959

By Bassam Kattaa

"Abstract - A heavy mineral survey of beach and dune sands including geochemical analysis for trace elements was undertaken to evaluate the economic potential of the sands and to understand the nature and distribution of the heavy minerals relative to potential source rocks. Results indicate that heavy minerals are generally derived from outcropping volcanic rocks that comprise a proportion of the hinterland in the south part of our survey area. The most abundant minerals are magnetite and pyroxene. The morphologies of the heavy mineral grains are angular to subangular, suggesting that they were transported short distances from the source rocks. Factors controlling heavy mineral distributions include wave and wind action, proximity to provenance, the fluvial drainage network, and longshore currrents.The most economically important mineral is ilmenite. Zircon and rutile concentrations are relatively minor and thus have lower economic potential."

Jan 1, 2002

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant's future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant's 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952

By John E. Lens

How much trouble can narrow vertical fissures in bedrock cause on a shallow bedrock site? Enough trouble so end-bearing H-piles range between 8 and 100 feet long in a single pile cap and tiebacks range from 40 to over 100 feet long within a 10 foot wall span. Sloped bedrock surfaces also complicated the tieback installation as the drill casing followed the sloped rock surface while drilling and caused unanticipated bending (and sometimes breaking) of the drill string. Warned via pre-construction rock probes and cores reaching over 80 feet deep at the Winooski, Vermont project site, the design and construction team expected anomalies in pile driving and tieback drilling due to fissures in the bedrock filled with soil and weathered-rock. The degree of abruptness in the variability in the rock surface, and its impact on pile driving and tieback drilling were less predictable. Close monitoring of pile and tieback installation, redesign of pile caps, and lengthened tiebacks overcame these anomalous fissures. This paper shares the lessons learned for overcoming these geologic challenges to benefit designers, contractors bidding the work, and ultimately, the owner, with lower contingencies.

Jan 1, 2006

CONTENTS PAGE FOGLER, M. F., and QUINN, E. J.-Scratch and Brinell Hardness of Severely Cold-rolled Metals. Discussed by H. S. Rawdon, Carl Benedicks, M. F. Fogler, A. L.Davis 1 GREEN, C. H. Eutectic Patterns in Metallic Alloys. Discussed by Carl Benedicks, Carle R. Hayward, G. E. Dalbey, George F. Comstock, C. H. Green. 3 ARCHER, ROBERT S., and JEFFRIES, ZAY.-New Developments in High-strength Aluminum Alloys. - Discussed by F. B. Coyle, M. F. Fogler, Zay. Jeffries, D. J. McAdam, Jr., Horace C. Knerr, Ernest Schweizer 6 FLICK, FULTON B.-Etching Aluminum and Its Alloys for Macroscopic and Microscopic Examination. Discussed by Samuel Daniels 22. MERICA, PAUL D., and WALTENBERG, R. G.-The Malleability of Nickel. Discussed by H. W. Gillett, Ancel St. John. L. W. McKeehan, A. L. Feild, A. L. Davis 23 ANDERSON, ROBERT J., and NORTON, JOHN T.-X-ray Evidence Versus the Amorphous-metal Hypothesis. Discussed by Zay Jeffries, Chu Phay Yap, Francis B. Foley, H. H. Lester, Edgar C. Bain, Ancel St. John, L. W. McKeehan, Carle R. Hayward, R. P: Heuer, Jerome Alexander, Carl Benedicks 26 COOK, MAURICE, and EVANS, ULICK R.-Recrystallization and Grain Growth in Soft Metals. Discussed by M. F. Fogler 36 POLUSHKIN, E. P.-Determination of Structural Composition of Alloys by a . Metallographic Planimeter. Discussed by H. S. Rawdon 36 BASSETT, WILLIAM H., and DAVIS, C. H.-Corrosion of Copper Alloys in Sea Water. Discussed by W. B. Price, W.. R. Webster, George A. Orrok, A. E. White, William H. Bassett, D. K. Crampton 38, Scratch and Brinell Hardness of Severely Cold-rolled Metals Discussion of the paper of M. F. FOGLER and E. J. QUINN, presented at the New York Meeting, February, 1925, and issued as Paper No. 1395-E with MINING AND METALLURGY, January, 1925. H. S. RAWDON, * Washington, D. C.-We had the privilege of looking over the data just given before they were published and we were not able to suggest any convincing reason for the differences that were secured

Jan 6, 1925

By Peter E. Price

Salt dome hosted metallic sulfide deposits are the product of a complex evolutionary system involving halokinesis, cap rock development and diagenesis, and the generation, migration, and accumulation of basinal brines and hydrocarbons. Hydrocarbons play an important role in: (1) the production of calcite cap rock which hosts some of the metallic sulfide and sulfur concentrations, and (2) the generation of the reduced sulfur available for metallic sulfide precipitation and sulfur formation. Hydrocarbons and related fluids also are involved in the transporta¬tion and remobilization of the metals. Hydrocarbon consumption, in the course of cap rock development and sulfide mineralization at Hockley dome, is estimated to have been 6.4 million barrels of oil or 114 million cubic feet of methane. Mineral textures, including cap-rock banding, sulfide bands in anhydrite, and fine sulfide mineral banding indicate both episodic fluid influx and fluid compositional differences through time. Features such as pyrite "shells" and sphalerite and marcasite hemispheres may have been localized by hydrocarbon droplets and /or bacterial colonies. Marcasite mineralization in shallow strata above and flanking Hockley dome is best developed over the western and southern parts of the dome. This pattern mimics the known distribution of sulfide mineralization, which is dominantly marcasite, in the underlying cap rock. The iron sulfide paragenetic sequence in the sediments is pyritohedral and cubic + pyrithohedral pyrite followed by marcasite which is encrusted by cubic pyrite. Sulfur isotopic averages for the three stages are +20.8, -20.2, and +6.4 per mil, respectively. These values generally coincide with cap rock sulfate (+20 per mil), cap rock hosted metallic sulfides (-20 to +4 per mil), and sulfur in hydrocarbons (+5.8 per mil). Hydrocarbon compositions indicate provincial variations in oil composition and generation history. Long Point and Boling domes, which have an intergrown sulfide-sulfate-sulfur mineral assemblage indicative of mixed reducing-oxidizing environment, contain oils that are less mature than Hockley dome which appears to be more mineralogically segregated. Sterane biomarker compositions of the oils at Hockley, Long Point and Boling domes indicate a local, dominantly terrestrial source. An oil sample from supracap sandstones on the northeast flank of Hockley dome contained over 750 ppm combined Fe, Zn, Pb, and Co, indicating that hydrocarbons are carrying or remobilizing metals. Cap rock calcite and anhydrite also exhibit provincial variations in strontium isotopic ratios. Calcite and anhydrite cap rocks from several sulfide mineralized domes in the Houston diapir province have strontium isotopic ratios that are more radiogenic than Jurassic sea water (>0.7078). A calcite sample within massive sulfides at Winnfield dome also has a high 87Sr/86Sr ratio (0.7085). Variations in strontium isotopic ratios with strontium content indicate the mixing of at least three Sr-bearing fluids in the cap rock environment, one of which may have been the metal carrier. Anhydrite residues from diapiric salt have strontium ratios up to 0.7100, considerably more radiogenic than Jurassic seawater. These high ratios indicate either that salt and anhydrite recrystallized sometime post-Jurassic in the presence of a fluid with a high 87Sr/86Sr ratio, or that they precipitated in the Jurassic from a fluid with a higher 87Sr/86Sr ratio than Jurassic seawater. Salt domes with cap rocks containing metallic sulfides have only been found in basins that have geopressured zones. Waters from geopressured zones in the vicinity of mineralized salt domes have salinities that are two or more times higher and iron and base metal concentrations that are three to one thousand times higher, than geopressured fluids from other parts of the basin.

Jan 1, 2013

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms in strata around a longwall gate road system at two sites in an underground coal mine near Ham, WY. Of particular interest was timedependent (on the order of several months) roof deformation. Strata above and below the coal seam are very weak, carbonaceous mudstones that have cohesionless planes of weakness oriented along bedding, which dips approximately 8° to 16° at N 49° E. An extensive array of instrumented roof bolts, roof extensometers, and biaxial stressmeters were installed during development mining at these two sites under variable depth of cover [I83 to 335 m (600 to 1,100 ft)], seam dip (10° to 16°), and top coal thickness [estimated to be 0.30 to 0.61 m (1 to 2 ft) on the downdip side of the entry]. Bolt load and roof deformation histories during the entry development periods were compared. Bolt loads at site 2 were less than those at site 1, which is consistent with the amount of overburden. Deformation magnitudes at site 2 were similar to those at site 1, but deformation rates were approximately 44% greater and nearly constant over time, whereas the deformation rates at site 1 decreased exponentially over time. Also, most deformation occurred above the bolt horizon at site two, but extensometer measurements at site 1 showed that a significant amount of deformation occurred within the bolt horizon. The most significant factor that influenced bolt tension and timedependent strata deformation was strength and Young's modulus of the strata. Finite-difference models support this conclusion.

Jan 1, 1996

By Peter Grandone, Ludwig Schmict

The injection of oil-field brimJs into subsurface formations containing mineralized water ·now is .recognizud as the most satisfactory and effective means of disposal in Kansas.· Other disposal ·methods, such as impounding brines in evapOTation nonds and controlled diversion into surface streams, have not prov-ed entirely successful, principally. because the volumes of brine to be disposed of were large, the soil f;?xtr~~mely porous, the net evaporation is low, and the rairiiall insufficient fc)r adequati.:~ dilution of the brine. The disposal of brine by subsurfaCE) inj'ection is often: more. expensive than by either of the above surface methods; nevertheless, surface dis:pos?,l ow.ing to the damaging effe-c.ts of· salt water to plant, animal and aquatic life and to potable water supplies has been:a long-continuing problem with many technical, economic, and 'legal·complexiti,2s

Aug 1, 1943

By W. B. Berwald

[Accurate ~cusirc::ie t of euusu.rface r,resw rus £Uld tee:: ?er:~t:,res in producin+ oil and as wells is one of tine ast iy,ulortant steps ever t,.s:en to place the rprwctice of retroleum ,-iroduction on an exact scientific basis. i'reerures and teial.or-tures in a -petrolcuia r4:, rvoir. have a rn..r..ed influence over the o:wvement of oil and ~c s both within the. reservoir and t~:rou,=Ii the various-size "flow otrin;;u" of proLucin,; wells to tine surface. Knovrled: ?c of theso fc,.ctgrs form a Laois for cny attei:ant to [.,-~ly eciantific j:cthods to the solution or analysio of mc.nj proble;ae encountered in the production of oil and 1c_c, Without a.ccur:tc mcaaurx,ients of reosures r:.nd tcn::paratuxes within the rocervoit and -well 'flo-,r strinL:s" tae aI,licution of w.ny proved enbinecrin and scientific princiy-,loo is on %,]

Jan 1, 1935