Search Documents

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By Khaled Morsy

The studied mine extracts the Sewickley seam using room-and-pillar method. The overburden at study site ranges from 400 to 800 ft. Eight years earlier, the Pittsburgh seam was mined 80 ft underneath the Sewickley seam. Parts of the mains at the study site experienced problems of rib spalling associated with floor heave. Numerical modeling was used to explain the mechanism of ground control problems encountered at the mains of the upper seam. The modeling results show that the ground control problems encountered were caused by multiple seam interactions with the previously mined longwall panel of the lower seam. Based on the modeling results, a criterion to predict the probability of multiple seam interactions was proposed.

Jan 1, 2006

TABLE TUNNEL NAME OWNER LOCATION STATE TUNNEL USE LENGTH (FEET) WIDTH (FEET) BID YEAR STATUS Gateway Tunnel project Amtrak Newark NJ Subway 14,600 24.5 2015 Under study

Sep 1, 2013

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title 11, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

Technologies are receiving a lot of 'press' - and rightly so; as they are seen as the means for achieving quantum leaps in productivity and cost reductions. A point of concern for Caterpillar is that we do not believe there is enough understanding of the infrastructure needed to support some of the future technologies, as well there is not enough utilisation of the current systems.

Jan 1, 1997

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By James R. Aggson

This Bureau of Mines report describes floor heave ground control problems that have been encountered in a new underground coal mine in West Virginia. Previous experience in the coal seam, the results of physical property investigations, and in situ rock stress determinations are discussed. The apparent cause of the ground control problems is the existence of a high, biaxial, horizontal stress field coupled with a floor member that has time-dependent deformation characteristics, A theoretical analysis of the failure process is developed. The analysis is assisted by finite element techniques. Mine design recommendations based on this analysis are presented.

Jan 1, 1978

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system&apos;s productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By Steve Dillingham

Whenever misfired holes or portions of misfired holes remain after a blast is fired, a hazardous situation exists until the unfired explosive materials have been disposed of properly. Yet, there are so many factors that can contribute to misfires that it is impossible to give blanket instructions on how to handle them. To complicate matters, misfires today are rare due to reliable blasting products. As such, it isn’t very surprising that many blasters have never had to deal with a misf i re condition. While the likelihood of a misfire occurrence is minimal, you should always be pre p a red to handle a misfire should you be involved in such an event. To begin, every blaster and blasting org a n i z a t i o n should develop a misfire policy which contains the company’s safe operating pro c e d u res, emergency contact list, as well as any regulatory compliance re q u i re m e n t s . Tailgate and/or company-wide safety meetings should communicate the company’s contingent misfire pro c ed u res and any special site-specific precautions BEFORE the start of any project.

Jan 1, 2004

By E. Esponosa-Gomez, J. A. Finch, A. R. Laplante

"Water quality plays an important role in oxide flotation. The effects on selective flotation of fine (1-16 um) pyrochlore of two types of water used at the Niobec concentrator, potable and plant recycle, were assessed. Several pyrochlore collectors and silicate depressants were tested. Water effects were different for each mineral-reagents) combination. In general plant recycle water decreased selectivity and increased reagent consumption. Interpretation of results is given in terms of electrokinetic effects, hydrolysis of cations, and mineral-collector interactions. Two techniques of treatment for plant recycle water, cation precipitation and zeolite adsorption were assessed. The former was found to be more effective under the tested conditions but recycle water continued to give poorer selectivity than the potable.INTRODUCTIONWater quality plays an important role in selective flotation. Specific effects have been reported by many workers (1-6) and in general the better the water quality the more selective is flotation. Water composition depends on origin and the minerals being processed. For example pulp containing salt-type minerals (calcite, apatite, dolomite) will contain more Ca and Mg cations than that from a sulphide deposit. Another source of water contamination is the flotation reagents added to the pulp, particularly if water recycling is practiced."

Jan 1, 1986

By Terry J. Close

From 1981-84, Bureau of Mines personnel examined and evaluated mines and prospects in the highly mineralized 62,400 acre Inyo Mountains U. S. Bureau of Land Management (BLM) Wilderness Study Area (WSA), located east of Lone Pine, CA. The 62,400 acres studied is the part of the 87,145 acre WSA designated as suitable prior to February 28, 1983. The WSA is underlain principally by quartz monzonite and quartz diorite that have intruded sedimentary and volcanic rocks. Three types of mineral deposits are present: 1) gold in fissure veins, 2) silver in fissure and replacement veins, and 3) talc in metasomatic lenses. Of the 84 nines, mills, and prospects examined, 54 are significant: 1) 5 in the intrusive rocks total about 4.4 million tons of inferred marginal gold reserves averaging 0.24 oz gold and 0.74 oz silver/ton; 2) three associated with intrusive-sedimentary rock contact zones total about 280,000 tons of inferred subeconomic silver resources averaging 7 oz silver/ton; 3) 27 gold and silver occurrences in the intrusive and sedimentary rocks total about 1.2 million tons of material in poorly defined bodies too small or low grade to be resources; 4) 15 gold and silver occurrences in the intrusive and sedimentary rocks are too poorly exposed to estimate tonnage and grade; and 5) four talc deposits along intrusive-sedimentary contact zones have inferred marginal reserves totaling about 640,000 tons. The marginal gold reserves at $450/oz might be profitably mined (reserve) at a gold price of about $600/oz and the subeconomic silver resources at a silver price in excess of about $27/oz. The marginal talc reserves might become minable at prices of about $50/ton and $80/ton for unprocessed and processed talc, respectively, after present supply sources are depleted. At most of the 54 significant mines and prospects, additional reserves or resources would likely be disclosed by trenching or drilling. Present in the WSA are 13 gold mills, numerous small pits and cuts, 270 underground workings totaling about 36,000 ft, and 80 mining benches totaling about 11,000 ft. Gold, silver, or talc were produced from most of the workings. A total of 1,561 lode and 18 placer samples were taken.

Jan 1, 1985

By N. L. Wimmler

The Metaline mining district was examined in 1942 by Bureau of Mines engineers with the cooperation of geologists of the Federal Geological Survey. Because the demands of war production were rapidly depleting reserves in some of the older zinc-lead producing districts of the United States, it was decided that an attempt should be made to increase the proved or indicated ore reserves of the Metaline district. With this objective, certain areas to be explored by diamond drilling were selected. The Bureau of Mines began work on this program. January 15, 1943; work terminated September 8, 1945. Forty-five holes were drilled in seven areas, The holes ranged from 154 feet to 2,050 feet in length. Their combined length was 38,150 feet. Thirty-three of the holes were drilled in. the North Pend Oreille and the West Bella May areas.

Jan 1, 1949

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By Russell J. Foster

Many important materials are derived entirely or partially as byproducts of primary copper, lead, and zinc production. This U.S. Bureau of Mines report examines the collective role of byproducts with regard to the economics of domestic mineral production, and their individual significance in terms of dollar value, end uses, and strategic considerations. The study also analyzes circumstances that have affected the competitiveness and structure of the U.S. copper, lead, and zinc industries, and factors that impact byproduct availability. These factors include production capacity at smelters and refineries, process technology, changing sources and composition of ores, regulations, foreign ownership, and byproduct demand and price. Policy considerations regarding stockpiling, regulations, and research are assessed.

Jan 1, 1991

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

By S. Rajeswari, D. Gopi

"Pitting corrosion inhibition of 304 stainless steel (SS) in groundwater with a ternary inhibitor mixture (phosphonic acid + bivalent cation + various surfactants) was studied with different environmental variables such as temperature, pH, dissolved oxygen and chloride ions. Critical pitting potential and corrosion potential were calculated for these test media using electrochemical techniques. Under the tested condition, the localized corrosion resistance of 304 SS was determined and the results are discussed. IntroductionPitting corrosion of metals and alloys is a major cause of failure in chemical processing desalination plants, scrubber for flue gas desulphurization (FGD) plants, water storage tanks and pipelines, petroleum refineries, etc.Heat exchangers and condensers in inland thermal and nuclear powerplants utilize groundwater as a coolant, but materials of construction are generally prone to localized corrosion.Localized corrosion attack can be initiated when the passive film on the metal is disrupted. The presence of certain aggressive anions such as chlorides (Cl-) can migrate to the actively corroding area and stabilize pitting corrosion. Attention has been focussed on improving the resistance of stainless steel against localizedcorrosion in aqueous environments.One of the most accepted methods of avoiding corrosion is by the addition of chemicals (inhibitors). Over the past two decades, some phosphonic acids have been explored due to their good corrosion inhibition efficiency and low toxicity (Fang et al., 1993; Karman et al., 1998; Rajendran et al., 1998; Gopi and Rajeswari, 2000a). Bivalent cations like Zn2+ are often applied as additives to inhibit the metal dissolution (Sekine and Hirakawa, 1986; Aruna Bahadur, 1998)."

Jan 1, 2003

By James Westfield

A brief résumé follows of some of the most recent activities of the Division of Coal-Mine Inspection that have had a favorable effect. on health, safety, and injuries at coal mines: 1. There were approximately 8,510 active coal mines in the United States during 1955. In all, 82,389 regular Federal inspections of coal mines have been made since Public Law 49 became effective in May 1941; 9,823 of these inspections were made during 1955. 2. The Bureau of Mines introduced the revised Coal-Mine Accident-Prevention Course for Supervisors in the coal-mining industry on March 1, 1948. Since that date, 19,455 supervisors and those aspiring to official positions have completed such training conducted by personnel of the Division of Coal-Mine Inspection.

Jan 1, 1956

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No. H0155113, "Noise Abatement of Continuous Mining Machines." It reviews, briefly, the aboveground tests performed on a Jeffrey 120M conveyor that were documented in Vol. I of the subject contract; and describes the performance of treatments implemented on underground equipment. The noise level at the operator&apos;s position in the aboveground-test facility was reduced from 101.5 to 91 dBA using treatments with satisfactory - aboveground - durability. Extensive underground evaluation has been performed only on the constrained layer damping, which has reduced the conveyor noise by 2 to 6 dBA depending on the operating conditions, and has been shown to be sufficiently durable. Other promising candidates for exploratory evaluation include resilient layers for the top/bottom decks, and smoother discontinuities between adjacent conveyor sections.

Jan 1, 1983