Search Documents

A New Technology of Applying SLon-2500 Magnetic Separator to Recover Iron Concentrate from Abandoned Tails

Sep 13, 2010

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By E. B. Brauer, W. Hurst, J. D. Clark

Because of drilling, completion, and workover practices, the permeability around a wellbore generally is different from the permeability of the formation. The zone with the altered permeability is called "skin" and its effect on the pressure or flow behavior of the well is called "skin effect". Hawkinsl has shown that the radius and the permeability of this zone are related to the skin by: If the permeability in the skin zone is less than that of the formation, the skin is positive; if it is more than that of the formation, the skin is negative. If the two permeabilities are equal, s is zero; that is, there is no skin. Van Everdingen2 and Hurst3 have given mathematical solutions to the case of a zone of reduced permeability around the wellbore. This skin effect is illustrated in Fig. 1. They treat the positive skin as a zone of reduced permeability of infinitesimal thickness around the wellbore. When applied to a well with negative skin, however, their solutions lead to the calculated flowing well pressure which is smaller than the formation pressure, i.e., an injection situation. This is a physical contradiction. In this paper, it is shown that this mathematical difficulty can be overcome by assuming an effective wellbore radius larger than the actual wellbore. Existing solutions2"4 are modified to include the effect of an enlarged wellbore radius, and thus enable the engineer to deal with negative as well as positive skins. Theoretical Development Van Everdingen and Hurst,4 through the use of Laplace transformation, obtained the following expression for transient fluid influx into a wellbore: The values for QtD, reported extensively by van Everdingen and Hurst,4 are obtained from the following integral:

Jan 1, 1970

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By L. C. Stilwell

Input-output analysis is a major branch of quantitative economics, and is used to analyse the flow of goods and services between production sectors in a national economy. Its purpose is to determine the relative value-adding capacity of each sector. The model has also, in recent years, found increasing use in assessing the environmental and ecological impact of development projects. It has, however, never been applied to individual production facilities, such as large mines, which themselves have complex economic structures, through which there is a flow of goods and services. Conventional cost and accounting systems, as used on mines, treat production sectors as separate cost centres, and do not determine the inter-relationships between them. This can lead to incorrect conclusions on the relative value of sectors and their impact on the total economic performance of the facility. This paper explains the basic principles of input-output analysis, and presents an example of its application to a simplistic model of a mine, which is used in the absence of any real data. The paper concludes that, by forcing definition of the value adding function of each sector, input output analysis will facilitate control of inputs, or costs. This will result in optimal application of resources and exploitation of ore reserves. The authors realise the model needs to be tested on an operating mine, and hope this paper will result in an opportunity to do so. The authors wish to thank the anonymous referees for their valuable comments.

Jan 1, 2000

By M. S. Delibalta, S. Kahraman, R. Comakli

The block cutting machine is one of the most important noise sources in the stone processing factories. In this study, the assessability of the noise from the block cutting machines in the stone processing factories using the P-wave velocity was investigated. The noise levels of some block cutting machines were firstly measured during the cutting of the three different rocks. Then, core samples of the same rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. A conversion factor was obtained by dividing the site noise levels by the laboratory noise levels. Then, thirty seven different rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. The P-wave velocity of rock samples were also measured in the laboratory. A strong relation between the laboratory noise levels and the P-wave velocity was found. The noise level from the block cutting machines can be assessed using the derived relation and the conversion factor.

Jan 1, 2011

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By Jonathan E. Ludlow

A field test was conducted to demonstrate and quantify the relationship between deep cutting and the creation of airborne respirable dust for longwall mining With a double-ended ranging drum shearer. The testing program was carried out on the 3 North longwall of North American Coal Company's Quarto No. y mine in Claringten, Ohio. Continuous recordings of the dust levels were made at both the midface and tail ate areas. Data were collected during 27 shifts during which time 81 complete mining, cycles took place. Both drum speed and the number of picks per line were varied systematically during the testing program to alter the depth of cut while the production rate was held constant by maintaining a constant haulage speed. The test results indicated that at the midface position, airborne respirable dust was strongly dependent upon the depth of cut as influenced by both the drum speed and number of picks. Drum speed had a much stronger effect than number of picks over the experimental range, since a halving of drum speed reduced dust levels by approximately 60 percent while removal of every other vane pick resulted in only a 2.1 percent reduction at constant production. At the tailgate position, however, neither effect was strongly apparent. A tendency for the slower drum speeds to he associated with reduced power consumption and higher haulage speeds (and therefore production rates) was also noted. It is recommended that longwall operators oper¬ate at the lowest available drum speed wherever possible.

Jan 1, 1981

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

By John H. Soule

Although known since 1902 , the Capitan iron deposits have not been mined mainly because of the low grade of the ore . A small amount of exploratory work carried on at an early date was reported . C. E. Johnson , district engineer of the Bureau of lines for New, Mexico , visited this propert , and as a result of preliminary sampling and mapping by the Bureau3/ and the Federal Géological Survey , an exploratory project was conducted during March , April , and liay 1944. Further mapping and logging of the vagon -drill samples was done by V. C. Kelly , geologist , of the Survey .

Mar 1, 1947

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 239 to 245. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropriateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at30th June, 1997, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1997

US 4,133,866-Selective recovery of the bound sodium content of red mud obtained in the production of alumina by the Bayer process The red mud is mixed with aqueous ferric sulfate, the resulting suspension stirred intensively at a temperature of 15-85°C and adjusted to a pH value of from 4.4 to 4 6, and the solids are removed. The clarified solution of sodium sulfate can be used directly for the leaching of additional bauxite T Lakatos, M Miskei, J Szolnoki, F. Toth, and L Revesz, assigned to Aluminiumipan Tervezo es Kutato Intezet, Almasfuzitoi Timfoldgyar, and MTA Geokemiai Kutatolaboratorium. Jan. 9, 1979. 3 pp (423-208). Filed: 10¬28-77 (846,588) Priority: Hungary, 10-29-76 (AU 364). US 4,145,398-Continuous digestion of bauxite with aqueous sodium hydroxide, with higher throughput in existing plants or the construction of smaller plants with equivalent capacity The ore suspension at a solids concentration of 1-6% by weight and temperature of 200-300°C is flowed through a digestion tube or nest of tubes at a velocity of preferably from 2 to 5 m/s and under a pressure of from 10 to 200 atm Heat is supplied by a fluid heat carrier flowing in countercurrent in a concentric outer tube. Preferably, some of the red mud is recycled to the digestion operation. L. Plass, assigned to Vereinigte Aluminium-Werke A.G Mar 20, 1979. 5 pp. (423-121) Filed: 2-27-76 (754,749) Same: British 1,437,548, dated May 26, 1976 Same Canadian 1,008,253, dated Apr 12, 1977. US 4,146,573-An aqueous slurry of red mud, formed in the Bayer process production of alumina from bauxite, can be solidified by treating the red mud with a described quaternary ammonium salt, continuing mixing until the red mud has set up to a rigid mass, and recovering the solidified concentrated red mud J Kane, assigned to Nalco Chemical Co Mar 27, 1979 4 pp (423-82). Filed 8-2-78 (930,251).

Jan 1, 1980

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

By William C. Hood

A leaching column technique that produces effluent similar in quality to coal mine drainage in the Eastern Interior Basin has been developed. The columns are charged with 1000 grams of crushed overburden and cycled through the leaching process once a week for twelve weeks. Inter-relationships among the important chemical constituents are very similar to those present in actual mine drainage waters, but the overall concentrations of ion are more dilute in the leachates. Multiplying the leachate concentrations by a factor of 4.5 gives values similar to mine waters. Available data suggests that each of the leaching cycles represents about three years of natural weathering, so that the leaching technique can predict the evolution of the mire drainage water over a time span of nearly 40 years. Use of the leaching technique with drill core samples should provide a method of approximating mine drainage quality in advance of mining and should be quite useful in identifying potentially toxic units in the overburden. However, the results should he considered to be a 'worst case' situation because the technique' does not consider the effects of reclamation.

Jan 1, 1984

By B. J. Moore

This publication contains analyses and related source data for 675 natural gas samples from wells and pipelines in 24 States and 5 foreign countries. The samples obtained and analyzed during calendar year 1980 are included in tables 1-4. Those samples included in tables 5-7 were collected during the years 1960 through 1979. However, permission to publish the analyses of those samples was not given until the past year when the operators were again contacted to seek release of the information. All of these samples were collected as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576. The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-two previous publications have presented the results of 12,152 gas analyses made prior to 1980. The first three, Bulletins 486,' 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1980. The other

Jan 1, 1981

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017