Search Documents

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

By M. Tangstad, H. Brun, P. Calvert, A. G. Lindseth

In 1999, Eramet bought the ferromanganese plants in Porsgrunn and Sauda (Norway) and Marietta (USA). With an ownership in the Comilog mine, the plants will operate with a high amount of Comilog ore. The properties of Comilog ore are reviewed and compared to a number of industrial operations. Important ore properties are chemical and mineralogical analyses, CO reactivity and mechanical strength. The advantage of Comilog ore is its contribution to lower energy and coke consumption. However, special precautions must be taken regarding the amount of fines and water introduced in the furnace, as Comilog ore is more porous compared to other Mn ores.

Jan 1, 2004

By Satyam Tiwari, Sarat Kumar Das

Tailings from mines and industries impose danger to the environment as evidenced by the recent failures of tailing storage dams. The tailings are mostly non-plastic with silt-size particles, but their behavior is largely dependent on the extreme void ratios of the material. Hence, the critical state provides an appropriate perspective in explaining the behavior of these geomaterials. Based on a comprehensive dataset of non-plastic tailings and non-plastic soils, an attempt has been made here to correlate critical state parameters to extreme void ratios and stress parameters. A hybrid algorithm with multi-objective feature selection (MOFS) and extreme learning machine (ELM) was used to establish the correlation and to identify the most influential input parameters. Based on the information from the proposed hybrid algorithm, a comprehensive prediction model is proposed using multi-gene genetic programming (MGGP) algorithm to facilitate quick estimation of critical state parameters. The performance of both models has been assessed using several performance metrics. The results from the study indicate that hybrid MOFS algorithms perform very well in the prediction of critical state line parameters and the identification of influential features. The findings of the study have significant implications for future research on the safe management of tailing storage facilities.

Dec 22, 2023

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By J. Coffin, R. Multani, C. Deredin

Glencore’s Strathcona Mill has recently evaluated a pyrrhotite depressant combination of diethylenetriamine (DETA) and sodium metabisulfite (SMBS) to improve its overall plant pyrrhotite- pentlandite (Po-Pn) selectivity, with the aim of producing a higher quality nickel concentrate. In a previous paper, key findings from a comprehensive lab-scale program (completed at the XPS Centre) were summarized where, of the depressants tested, DETA/SMBS combination was found to be the most effective in improving the Po-Pn selectivity. The present paper describes the metallurgical program recently completed at Strathcona Mill; DETA/SMBS evaluation on select plant “grab” samples as well as the major results of three DETA/SMBS plant trials conducted on several plant ore feeds (long-term testing). Interestingly, it was found that there was variable success in using DETA/SMBS depressants on the different plant ore feeds; DETA/SMBS (dosage: 25/50 g/t milled feed) on lower Cu feeds demonstrated a ~2% Ni recovery increase at the same Ni grade. On the other hand, higher Cu feeds demonstrated virtually no benefit from DETA/SMBS at the same plant dosage, suggesting that higher DETA/SMBS dosage (at specific locations) than that tested is required to overcome the increased Cu-DETA complexation for these particular feeds. Glencore Nickel – Sudbury Integrated Nickel Operations owns and operates Strathcona Mill which has been processing Ni-Cu ores from the Sudbury Basin since 1968. The valuable sulfides are pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2, majority of the sulfide gangue is pyrrhotite (Po) – Fe(1-x)S [0 < x ≤ 0.125] which is present in two forms: hexagonal Po (Fe9S10) and monoclinic Po (Fe7S8) (Multani & Waters, 2017; Lawson et al., 2014). Currently Strathcona Mill processes ore mined from two primary sources from the Sudbury area and produces two concentrate streams: (1) nickel-copper concentrate that is sent to the Sudbury Smelter; and (2) copper concentrate that is shipped to the Fonderie Horne (Glencore Copper, Rouyn-Noranda).

Jan 1, 2019

By S Christensen

In August 2001 the Minister for Conservation declined an application by GRD Macraes for an access arrangement to enable work at the Globe Progress Mine near Reefton. In her decision, Ms Lee said:æI have considered whether potential compensation and the proposed safeguards against some of the adverse effects are sufficient to outweigh my concerns as to the loss of conservation values, consistency with the objectives of the Conservation Act, the purposes for which the land is held by the Crown and, to a lesser extent, the North Westland Regional Management Plan. I do not think they are sufficient. To my mind, my concerns as to the consistency with the objectives of the Conservation Act, the purposes for which the land is held and the loss of some conservation values in particular, outweigh any potential compensation and possible mitigation of adverse effects.Æ Commenting on the MinisterÆs decision Guy Salmon of the Ecological Foundation stated that the Minister should have invited the applicant to provide a 10 000 hectare pest-free wildlife sanctuary as part of the æpriceÆ for obtaining that access. However,æfor many people of green persuasion, it has become fashionable to say no every timeàthose who really have the well-being of the environment at heart, will want to look carefully at the bigger picture of environmental restoration needsàThe deciding criterion: the mining company should show that its involvement on conservation land would produce a net conservation gain. That is a criterion that creates the right incentives for win-win-win solutions on conservation land.ÆThis paper considers whether the concept of off site mitigation is one which fits within the current legal regime. Two questions arise:Can such mitigation/compensation be legally considered in access arrangements or required as a condition of resource consents? Is this a realistic option for industry to be pursuing?

Jan 1, 2002

By T. S. Lundy, J. I. Federer

Chemically purified Zr95and Cb95 have been used in determining self-diffusion coefficients in the bcc phase of iodide zirconium over the temperature range of 900o to 1750°C. The temperature dependence of the diffusion coefficients could not be described by the usual Arrhenius-type equation over the entire temperature range. Values of the apparent frequency factors (D0)a and activation energies (Q)A for ZR95 varied from 4.8 x 10-6 to 2.5 x 10-2 sq cm per sec and 20,700 to 46,900 cal per mole, respectively, between 900°and 1750°C. Similarly, for Cb95, values of (Do) a and (Q)A varied from about 2.4 x 10&apos;5 to 0.25 sq cm per sec and 26,500 to 56,800 cal per mole, respectively. The data may be described in terms of the a to ß transition temperature of 1136 °K and the absolute temperature of the diffusion anneals by the following eauations: SEVERAL studies on the diffusion of Zr95 in zirconium have been reported.1"5 The values of the constants contained in the usual Arrhenius-type equation for describing the temperature dependence of the diffusion coefficient, D = Do exp [- Q/(RT)], are summarized in Table I. The reported values of Do, the frequency factor, and Q, the activation energy, are seen to vary by factors of about 60 and 1.6, respectively. Examination of the data from any one study indicated reasonable consistency of measurements. The large discrepancies of over-all results, therefore, cannot be explained on the basis of experimental scatter. One possible explanation for the differences in results could be a varying impurity content of the zirconium. Another possibility is that the radioactive daughter, Cb95, influenced the values of some of the determined diffusion coefficients. Therefore, the first of the three purposes of this study was to reconcile the large differences in diffusion results that have been obtained. Several empirical relations have been proposed to relate the diffusion coefficients in solids with physical properties, such as the absolute melting point, the heat of fusion, and the heat of sublimation.

Jan 1, 1963

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source. &nbsp; Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine. &nbsp;Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991

By Lu Li, Sara E. Wilson

Occupational exposure to whole body vibration has long been associated with increased incidence of low back pain and low back injuries1. A number of studies have investigated transmissibility of seat pan vibration 5, 6. While transmissibility has been well researched, the mechanism by which vibration may induce injury has not been thoroughly studied. Winter et al. identified increased reflex response delay after vibration exposure and speculated that muscular fatigue may be the cause of this increase9. However, a mechanism has yet to be demonstrated completely. A potential mechanism that may explain the increased risk is neuromotor habituation. Muscle spindle organs have been shown in the extremities to be sensitive to muscle and tendon vibration. Rapid length changes in muscle have been shown to result in kinesthetic illusions as the regular firing of the muscle spindles is interpreted as muscle lengthening4, 7. These illusions have also been demonstrated in the paraspinal musculature2. With removal of vibration, research in the extremities has demonstrated increased positioning errors, probably due to neuromotor habituation8. In this research, it has been hypothesized that neuromotor habituation after exposure to occupational vibration will increase positioning errors. It is further hypothesized that these errors can be shown to be linked to increased reflex response time. Such increased reflex response time could, in turn, decrease spinal stability and increase low back injury risk. Methods Both positioning error and sudden load response were measured before and after exposure to 20 minutes of 5 Hz, 0.223 m/s2 RMS seat pan vibration. Subjects were asked to sit on an unpadded seat without a backrest. Throughout the whole body vibration period, subjects were instructed to put their hands on a stable hand rest and feet on an adjustable stable footrest. The subjects were instructed to assume a comfortable and relax sitting posture for the duration of the exposure. Positioning error was measured using an active-active reposition sense protocol. Electromagnetic markers (Motionstar, Ascension Tech, Burlington, VT) were used to track trunk motion. With markers attached to the skin at the T10 vertebra, the S1 vertebra and manubrium, trunk flexion (the angle from vertical of the line connecting T10 and S1) and lumbar curvature (the difference in inclination of the T10 and S1 markers) were tracked. In the reposition sense protocol, subjects were asked to maintain an upright trunk flexion and to rotate their pelvis and lumbar curvature to assume a target lumbar curvature. In the protocol subjects completed training trials, where they were asked to match their lumbar curvature using a visual display, and assessment trials, where they were asked to reproduce the lumbar curvature from memory. After two initial training trials, training trials and assessment trials were alternated for a total of 3 assessment trials. Reposition error was defined as the absolute difference between the target lumbar curvature and the lumbar curvature the subject assumed during the assessment trials.

Jan 6, 2006

By D. S. Burgess

This report summarizes the incidents that preceded the December 9, 1970, propane-air explosion in Port Hudson, Mo., and then attempts to establish the nature of the explosion from the ensuing events. Special emphasis is given to possible ignition sources, the distribution of flammable vapors, and the analysis of blast damage. Both near-and far-field damage indicated that this explosion may be attributed to the detonation of propane in air with an energy release equivalent to that from about 50 tons of detonating TNT.

Jan 1, 1973

By Colin C. West

On August 7, 1986, Barge 45, while being towed near the mouth of the Niagara River, was swept downstream and pinned against one of the central piers of the Peace Bridge. The barge rested against the pier with 125 feet overlying the Canadian border and 50 feet overlying the American border. The tug boat which was towing the barge was lost further downstream. Fortunately, the crew escaped and were rescued with no loss of life. There was serious concern about the potential erosion effects of the river currents on the foundation of the bridge pier as caused by the flow concentrations around the barge structure. Due to the time of year, with the approaching Fall and associated worsening weather conditions, it was imperative that the barge be removed as soon as possible. Donjon Marine of New Jersey, the United States Navy&apos;s Atlantic Zone Contractor, was called on to retrieve the barge. By this time the original owner had abandoned the wreck.

Jan 1, 1987

By K S. Smith, J Woodhead, K Olson Hoal

Mineralogy is the link between ore formation and ore extraction. It is the most fundamental component of geomet programs, and the most important aspect of a life-of-project approach to mineral resource projects. Understanding orebodies is achieved by understanding the mineralogy and texture of the materials, throughout the process, because minerals hold the information required to unlock the value they contain. Geomet mineralogy programs absolutely require the appropriate expertise and at least three steps of mineral characterisation prior to using semi-automated or other methods: field examination, thorough core logging, and optical microscopy. Economic geological inputs for orebody characterisation are necessary for orebody understanding, and are exemplified by current research in the Zambian Copperbelt, where revised sequence stratigraphy and understanding of alteration, metasomatism and metamorphism can be used to predict topical issues at mine sites. Environmental inputs for sustainability characterisation are demonstrated by recent work on tailings from the Leadville, Colorado, USA area, including linking mineralogy to water quality issues. Risk assessments need to take into account the technical uncertainties around geological variability and mineral extractability, and mineralogy is the only metric that can be used to make this risk contribution.CITATION:Olson Hoal, K, Woodhead, J and Smith, K S, 2013. The importance of mineralogical input into geometallurgy programs, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 17-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By George Holderer

THE Enos Coal Mining Co. owns an area underlaid by coal, of approximately 5000 acres. This property is situated 9 miles from Oakland City, in the southern part of Indiana. The mine has been in operation 5 years, during which time some 350 acres have been stripped, and stripping is now proceeding at the rate of about 100 acres per year. TOPOGRAPHY These coal lands consist of gently-rolling agricultural fields which in times past were farmed for wheat. There is no timber and but very little brush to contend with. The overburden varies from 10 to 60 ft. in depth. A thin bed of slate overlies the coal, followed by limestone, which varies from 3 to 15 ft.; this, in turn, is followed by sandstone, slate, shale and clay. There is a very wide variation in the thickness of all of these beds. The coal has an average thickness of 5 ft., and is a good grade of high-volatile bituminous. MINING OPERATIONS Briefly, the sequence of operations is: drilling holes with churn drills; blasting with L. 0. X.; stripping overburden to uncover coal and, finally taking up the coal, which is sent to a tipple for cleaning and sizing. In order to show what is being accomplished by the use of L. 0. X., results will be shown from May to November, 1926, inclusive, and compared to the same period in 1925. No work was done in No. 1 pit during May, 1925, hence all figures are unduly low for this month. Drilling There are in use 8 No. 44 Loomis clipper drills, caterpillar traction with gasoline engines; recently these were equipped with extra heavy stems, measuring 26 ft. overall and 4 ½ in. dia., to increase the speed of drilling. In addition, 4 No. 1 ½ G non-traction drills have been acquired, and are used to save the time of the larger drills when recleaning is necessary.

Jan 1, 1927

By J. Nalaskowski

A study of the interfacial properties of the basal plane and the edge surfaces of talc is described in this paper. The isoelectric point measured at the two different crystallographic planes by the streaming potential method was found to be similar and exists at about pH 3.0. In the case of the edge surface the zeta potential increases at higher pH values which can be attributed to the hydration of magnesium ions at the edge surface. The atomic force microscopy (AFM) colloidal probe technique was used to measure interaction forces. For such experiments a 20 um talc particle was attached to the AFM cantilever and forces between the edge of the talc particle and two different crystallographic planes of talc were measured at various pH values. These measurements, while being qualitative due to the poorly characterized contact area, show differences between the properties of the base plane and edge of the talc and correspond to the results from streaming potential measurements. Finally, the differences in the hydration of the basal plane and the edge of talc are revealed from molecular dynamics (MD) simulations. The basal plane of the talc is much less hydrated than the edge, as can be seen from the water density distribution functions, which correlate quite well with the contact angle measurements at the basal plane surface and the edge surface of the talc sample.

Jan 1, 2006

By Kenneth Eilerts, Vincent Smith

"INTRODUCTION Knowledge of the Phase relations of fluids produced from combination wells 4/ at the pressures and temperatures characteristic of production from natural reservoirs is essential to efficient recovery and refining practice. An accurate sample of the fluid from such wells may be prepared by mixing (in the proportions of the measured gas:liquid ratio) gas and liquid taken from the separator conditions of steady flow; and physical properties of the sample, at significant pressures and temperatures, may be determined with suitable laboratory apparatus for use in the solution of engineering problems. The results of study of sample so obtained and of mixtures of gas and liquid from the separator combined in other proportions are presented in this report. Attention was given in the study to the relationship between the physical properties of what may be regarded as the constituent materials - the gas and liquid taken from the separator - and the properties of mixtures of these constituents. Data obtained for the complete range of mixture Proportions are expected to provide a reference scale for the study of other combination-well fluids produced at different liquid:gas ratios."

Apr 1, 1942

The sedimentary basins of this region developed in the collision zone of thePacific Ocean plate and the continent. Stresses were transmitted thorough wedge-like lithospheric blocks, such as the Okotsk Sea, East Kamchatka, Aleutian and other smaller blocks. Compression and inversion were more active at the boundaries: ***INSERT EQ*** and ***INSERT EQ*** in places. Tension, rifting and the increase in the rate of sedimentation were marked in P1-2, P3, N12, and also in N2 û Q in places. Structural plan changes of the sedimentary basins and possible oil, gas and fluid migration occurred more actively at the boundaries: ***INSERT EQ***.

Jan 1, 1995

By Met M, Worner H. K

In pursuance of the investigation into the influence of various elements on the properties of lead during the past year, the effect of several elements on the creep rate of commercially pure lead has been investigated; a standard initial stress of 500 lb. per sq. in. having been adopted for comparison purposes. Other work which has been carried out indicates that the relative results of creep tests may be altered by varying the applied stress, but this aspect of the problem will need to await further investigations for itscomplete elucidation. The results obtained with dilute tellurium alloys are considered sufficiently interesting, and in some respects are so extraordinary, as to warrant publicatiorr at this stage.n must be realised however that, since the results obtained appear to be at variance with those said to have been obtained in practice and those previously published, the present investigation can only be considered as a contribution to our knowledge of the general problem.Consequently it is not considered advisable or necessary to offer detailed explanation of the results given. In fact, some features of the tests about to be described will need further investigation before an adequate explanation is possible.

Jan 1, 1936

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973