Search Documents

By C. Sahyoun

The influence of microwave treatment on copper flotation has been investigated. Comparative batch flotation tests carried out on ore treated at 5?12 kW for 0.1?0.5 s showed that improvements in copper recovery of between 6?15 % could be achieved compared with untreated ore. Both recovery and cumulative grade increased with increasing treatment time and power. A preliminary economic analysis showed that microwave treatment will be economically viable if recoveries similar to those determined on laboratory scale can be achieved on a plant. Keywords: microwave treatment, copper ore, flotation, liberation, recovery

Jan 1, 2005

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

Pressure Oxidation of Sulfide Gold-Bearing Concentrates with Double Refractoriness

Sep 13, 2010

1. Scope of project In South Australia, the Western Mining Corporation operates the underground copper and uranium mine Olympic Dam. The deposits concerned are enormous (approx. 570 million tons) and have been mined since 1988. At the end of 1996, Western Mining decided to increase the capacity of Olympic Dam from 85,000 t.p.a. to 200,000 t.p.a. Planning At this point, SIEMAG-GHH Mining Division was asked to carry out a study including the planning of the entire shaft hoisting operations and calculation of the investment and operating costs involved. With the assistance of Australian partners, the study was completed within a single month. The principal points of the study were as follows: ? Planning of the hoisting machinery for 1,375 tons per hour from the surge bin below ground to the discharge bunker above ground. ? Optimisation of the hoisting operation with regard to maximum availability and safety. ? Optimisation of the time schedule to minimise the financing costs of the investment. ? Statement of the investment and operating costs. ? Comparison of the technical data, design and availability of the planned machinery with reference plants. Construction of the plant Following acceptance of the study, the decision was taken within a few weeks to implement it. SIEMAG Transplan GmbH received the order to execute the entire shaft hoisting machinery on the basis of the study submitted. The decisive factors in placing the order were: ? Convincing study, adherence to schedule ? Reference to comparable plants elsewhere ? Reference with regard to availability.

May 1, 2003

These proceedings consist of an introduction and four descriptive papers. The first paper is an update on fire protection for large haulage vehicles, the second paper is concerned with improved visibility systems for large haul- age vehicles, the third paper is on improved ladders for large haulage vehicles, and the fourth paper is concerned with large haul-age vehicle operator training systems.

Jan 1, 1980

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By Robert Boyd

The Diamond Markets ? Supply has continuously increased over the past 25 years ? However, global supply is expected to drop by 1 to 2% by 2015 ? Demand Driven Market ?Demand is expected to grow 3% annually through to 2015 ? Supply Squeeze Anticipated (2010 to 2015) ? Consumption is exceeding rate of discovery, mine development and reserve replacement ? These fundamentals are driving increased capacity and production at existing mines in South Africa, Botswana and Russia and new areas such as Canada ? Canada is now the third largest diamond producing country in the world ? These fundamentals are also driving record levels of exploration expenditures throughout the world with particular focus on Africa and Canada

May 1, 2006

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By C. F. Vos, J. D. Miller, J. C. Davidtz

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate(DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromite rejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2006

6889. Aslakson, C. I., and Swick, C. H. Gravity Observations in Peru and Colombia. Coast and Geodetic Survey,-Special Pub. 233, U. S. Government Printing Office, Washington, D. C., 1943, 18 pp. (Price, 10 cents.) In accordance with the policy of cooperation among American republics, the-United States Coast and Geodetic Survey in 1941 made gravity surveys in Peru and-Colombia. The information was desirable for determining the figure of the earth for geophysical purposes and for studying the relationship between intensities of gravity and deflections of the vertical. The survey instrument was the Brown pendulum apparatus. 11 gravity stations were established in Peru and 13 in Colombia. The results obtained at these stations are given in a table covering observed gravity, theoretical gravity, and anamalies. - V. S.

Jan 1, 1943

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By S. D. D. Welsby

"A pilot-scale flotation column was used to evaluate four polyglycol frothers at Teck’s Highland Valley Copper Mine. The column was fed with flotation plant feed from the grinding circuit cyclone overflow. Frother dosage was changed by controlled addition to the column feed. Pulp, froth and metallurgical performance were assessed using gas dispersion measurements, water recovery and copper, molybdenum and gangue grades and recoveries. Ranking the frothers based on pulp and froth phase performance using gas dispersion measurements and water recovery yielded contradictory rankings. All of the frothers changed the froth structure in a similar manner such that, at the same structural conditions, they all gave the same degree of separation between water and entrained solids. The only difference between the frothers was what dosage was required to achieve a certain structure. Changes in pulp structure appeared to be related to the critical coalescence concentration (CCC) for each frother. Changes in froth structure were not completely described by the CCC and involved other factors, such as the hydrophobicity of particles in the froth. All of the frothers were capable of achieving the same metallurgical result, just at different dosages. Optimal dosages for the frothers were anywhere from the CCC, where copper and molybdenum grades were maximised, to 2 to 3 or 4 to 7 times the CCC, where copper and molybdenum recoveries, respectively, were maximised.INTRODUCTION Background Due to supply issues, Teck’s Highland Valley Copper (HVC) Mine replaced Dowfroth 250C, their auxiliary frother, with Huntsman Polyfroth W31. The primary criterion for selection was that the new frother gave the same performance as Dowfroth 250C, minimising disruption to the circuit. Frothers play a dual role in flotation, altering the bubble size in the pulp zone and the stability of the froth. A stronger or weaker frother, or a blend of both, will alter the balance between pulp and froth effects and, ultimately, metallurgy. Dowfroth 250C and Polyfroth W31 may not necessarily be the best frothers for HVC from a metallurgical standpoint. There may be a different frother or frother blend that could deliver higher recovery in the bulk roughers."

Jan 1, 2014

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

By E. A. Lowe, J. W. Smith, C. W. Overton

"The operations of Bethlehem Copper are situated in the south-central interior of British Columbia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Columbia.The minerals are chiefly chalcopytite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies some pyrite is present. Average grade of mill feed is 0.55% copper.History of Milling Operations Production commenced in December 1962 at a rate of 3,000 tpd in a plant that comprised two-stage crushing followed by rod and ball milling. Production ratings were increased to 6,000, 10,000 and 12,000 tpd by the addition of a further stage of crushing and more rod and ball mills. When the last expansion was completed tonnage throughput exceeded the 12,000 ton designed rate and was stabilized at 15,500 tpd.However, recovery did not meet expectations at the expanded rate because of coarse flotation feed. Capacity in the rod mill circuits exceeded the subsequent fine grinding capacity, resulting in poor liberation. Studies were initiated to improve recovery without decreasing throughput.Description of Operation Prior to Pebble Milling Crushing with primary, secondary and a closed tertiary stage proceeds at a scheduled 20.5 shifts per week. Fine ore screened on 1/2"" x 4"" apertures is stored in a 30,000-ton bin ahead of two 12.5' x 15' rod mills. Rod mill discharge joins secondary ball mill (one 10.5' x 14' and one 11' x 14') discharge for classification in a single 50"" cyclone which closes the secondary mills. Overflow from this cyclone is split between three third-stage ball mill-pump-cyclone circuits (two 11' x 14' and one 12.5' x 15'). Prior to addition of the two pebble mills the flotation feed was produced by this three-stage grinding system. Grinding criteria are shown in Table I."

Jan 1, 1975

By Charles H. Minott, Michael J. Markow, Robert D. Wyatt, Fred Moavenzadeh

The substantial investment in tunnels anticipated in the next twenty years has focused new attention on the economics of tunnel construction itself and on some costly problems associated with underground work: the uncertain geologic conditions, the performance and adaptability of men and equipment, and the need for quicker, more efficient excavation methods. There also exists a need to develop better ways of estimating tunnel construction. Inaccuracies in current bid estimates stem from a number of causes, among them (1) the effects of geologic conditions, which are not adequately known prior to construction, (2) the dependence of actual cost on the construction method used and on the interactions among the operations occurring underground, and (3) the reliability of tunneling equipment. Inability to estimate final costs for conventional tunneling more accurately has in turn caused difficulty in gauging the costs and benefits attributable to new tunneling technologies either under development or for which R&D programs are planned. ATTRIBUTES OF THE TUNNEL COST MODEL This paper presents a computer based Tunnel Cost Model (TCM) which quantitatively assesses the uncertainties inherent in underground work, and is detailed enough to aid in preparing estimates or bids. The model employs appropriate techniques of subjective (or "degree of belief") probability and computer simulation of tunnel construction operations to estimate distributions of total tunnel

Jan 1, 1974