Search Documents

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By J. Douglas, W. T. Ford, G. E. Henderson, I. F. Roebuck

An implicit numerical method is presented for simulating the differential and algebraic relations governing one-dimensional three-phase flow in porous media. The method is based upon compositional representation of the hydrocarbon system. Variable physical properties and water-oil capillary forces are included in the formulation; however, the effect of gravity is ignored. The effects of changing composition and mass transfer are considered through the use of known phase behavior concepts and correlations. The differential and algebraic equations and the numeric approximations to these equations are presented, and the computing algorithm is discussed in detail. This method is used to simulate a single-phase, two hydrocarbon-component gas displacement laboratory experiment. The method is also applied in simulating a solution gas drive and a gas injection problem using a reservoir oil represented as a nine-component mixture. For comparative purposes, the latter two problems also are examined with a one-dimensional volumetric model. The results of the simulation of the laboratory experiment demonstrate the relevance of this method to problems wherein the effects of mass transfer significantly enter the displacement process. The comparison of the results of the volumetric and compositional methods applied to a reservoir system illustrates not only the advantages and benefits derived from examining the hydrocarbon system composition, but also the necessity of this approach in application to a general reservoir problem. INTRODUCTION The advent of large memory, high-speed digital computers enabled reservoir engineers and mathematicians to pool their knowledge in the development of sophisticated techniques for the prediction of oil and gas reservoir performance. These techniques have progressed from volumetric and trend analysis calculations to the development of "mathematical models", or reservoir simulators. These latter models, in general, utilize finite difference approximations to the rather complex partial differential equations that mathematically describe the physics and thermodynamics of fluid flow in porous media. Many forms of this "model" type are available today, and much of the recent literature has been devoted to either improving known methods or developing new techniques for use in these prediction methods. The more advanced techniques in use at this time consist of the solution of differential and algebraic relations that describe a reservoir geometry in one, two or three dimensions and that incorporate reservoir hydrocarbon and water fluid systems that obey specified physical laws, having properties that might easily be measured in the laboratory. This type of model utilizes formation volume factors and other volumetric data, expressed directly as functions of pressure, to represent the reservoir fluid system. Experience gained with this type of simulator, commonly known as a "beta-factor model", has indicated that the approach has many outstanding defects, most of them due to the assumption that those properties measured in the laboratory completely describe the behavior of the fluid system throughout the life of the project under study. The effects of varying hydrocarbon composition and mass transfer between the phases of this hydrocarbon system must, by definition, be ignored. These defects, which may often be ignored in

Jan 1, 1970

By Steve Kral

The mining industry in northern Ontario is known mostly for its huge nickel deposits. Inco’s and Falconbridge’s nickel mines in the Sudbury Basin are the best known. And with nickel prices being what they are, interest in the region continues. And how. Inco and Falconbridge want to merge. Teck Cominco wants Inco, but without Falconbridge. Xstrata made a hostile bid for Falconbridge, which Falconbridge rejected. And, in June, Phelps Dodge trumped them all when it made an approximately US$40-billion friendly offer for Inco and Falconbridge in a two-part deal.

Jan 1, 2006

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By P. Chaddock

The Thompson Mill has a capacity of 15,000 T ID of ore and produces two grades of nickel concentrate, copper concentrate and occasionally graphite concentrate. Up to July of 1985 we processed two distinct ore types: T-1 ore, averaging 2. 8% Ni and . 2% Cu and Pipe Open Pit ore, averaging . 8% Ni associated with peridotite and serpentine. Presently our ores from T-1 mine and Thompson Open Pit are of the same type and are processed together. (Figure 1)! n October, 1982, we decided to install an Outokumpu Courier 300 on-stream analyser on an initial 6 streams. The equipment was delivered to the mill on May 2, 1983 and the first analyses were generated by June 17th. The calibrations were 35% complete by the mid-July summer shutdown and were completed in the fall. 1. 2 Analyser Slurry Feed System:The key to successful on-stream analysis is delivery of the sample streams to the analyser.Our system uses pressure-thief sampling for collection. (Figure 2) Initially we used thief samplers modelled after the Outokumpu design, with turbulence bars upstream of the collection point. These units have been replaced with simple laterals as they have worn out. Our thief samplers are mounted vertically on pump discharges and we believe sufficient turbulence exists to ensure representative sampling.

Jan 1, 1987

By Earl Redman

The Juneau Gold Belt portion of the Juneau Mining District has historically had the greatest mining and exploration activity within the district. Between 1880 and 1983, the mines within the Juneau Gold Belt produced 6.7 MM oz gold, 3.1 MM oz silver, and 45 MM lbs lead, which had a total value of about $157,000,000 at the time of production. This report summarizes Bureau of Mines work completed in 1986, the second year of the Juneau Mining District study. Fifty mines, prospects, and occurrences were examined and 638 samples were collected for analysis during 1986. Metallurgical samples were collected from seven deposits and preliminary tests of cyanide amenability have been completed for five of these. The simultaneous discovery by private industry and the Bureau of gold-bearing quartz veins cutting diorite gneiss recently exposed by the retreat of the Herbert Glacier is the most notable result of work during 1986. This location yielded gold values up to 7 oz/st.

Jan 1, 2011

By F. Dieu, C. Laughton

CERN, the European Laboratory for Particle Physics, is, at present, constructing an underground tunnel and cavern network to house a Large Electron Positron (LEP) colliding beam machine. This paper describes the techniques adopted to permit the excavation and temporary support of the access shafts through a series of glacial moraines, at depths of up to 80 m, to reach the bed-rock. Owing to the presence of superficial and deep water-tables, the variable nature of the moraine deposits and, above all, the tight work schedule, a combination of diaphragm walling and ground freezing was employed.

Jan 1, 1987

By George W. Maynard

(Pittsburg Meeting, March, 1910.) AT the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, ill their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.1 The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper, 2 which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly -every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the. manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas;3 read at the New York meeting of, the Institute, February, 1885, I show that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on and advanced by chemists and metallurgists at home and abroad. 1 Trans., viii., .5 (1879-80). 2 The Iron Age, vol. 22, No. 17, p. 3 (Oct. 24, 1878). 3 Trans.. xiii., 785 to 791.

Jul 1, 1910

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Jochen Petersen, Thandazile Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques. The anodic dissolution process has been established to be a seven-electron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions. The number of electrons transferred in the carbonate and sulphate salts suggests that the sulphur is oxidised to a thiosulphate intermediate and the copper and iron released as Cu+ and Fe2+. The Cu+ and Fe2+ is subsequently oxidised in solution in non-Faradaic reactions. The deportment of Fe2+ and S2O32- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, however observations made on the mineral surface after leaching do not support the formation of elemental sulphur. Scanning electron microscopy and energy-dispersive spectroscopy analysis of the mineral surface suggest presence of an iron–sulphur surface layer completely free of copper under the ammonia–ammonium sulphate conditions, an iron-rich surface layer under ammonia–ammonium perchlorate solutions and absence of surface layer build up under ammonia–ammonium carbonate solutions. INTRODUCTION Hydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different approaches to hydrometallurgical treatment of chalcopyrite can be carried out. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base-metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilisation of copper(I) and copper (II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation 1 (Beckstead & Miller, 1977a):"

Jan 1, 2015

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005

By Raquel Costa, Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, Ana Filipa Marques, Andreia Afonso, Maria Ana Martins, António Calado, Luísa Pinto Ribeiro

Since its formation in 2004, the Task Group for the Extension of the Continental Shelf (EMEPC) has been collecting hydrographic, geological and geophysical data to support the extension of the continental shelf beyond 200 NM. In 2008, the EMEPC acquired a 6,000 m rated ROV named "Luso" and has been cooperating with several national and international institutions to increase and improve its operational capabilities to conduct research on deep-sea minerals. The Portuguese continental shelf corresponds to a broad area of the seafloor encompassing different physiographic domains: the mid-Atlantic ridge system, abyssal plains and numerous seamounts. From 2008 to the present, the mid- Atlantic ridge and seamounts have been the most visited sites with the ROV "Luso". Several hydrothermal vent sites are known to occur along the mid-Atlantic ridge to the south of the Azores archipelago and mostly within the Portuguese EEZ. Vent fields were also discovered in the extended continental shelf, namely the Rainbow and the Moytirra sites located to south and to the north of the Azores archipelago, respectively. The most studied seamounts correspond to those forming the Great Meteor chain and the Madeira- Tore rise. All these visited sites are related either with the occurrence of polymetallic sulphides or cobalt rich Fe-Mn crusts and the opportunities to further pursue their exploration will be discussed.

Sep 1, 2014

By J. Persson, N. G. Bliss

Electric furnaces used for smelting and those used for scrap melting exhibit different performance profiles in terms of electrical characteristics. However, the underlying principles are the same for either case. The rationalization of these variables is a major concern for furnace operators and designers. This paper presents the results of a two year study of high speed real time data from a number of electric furnaces around the world, covering a very wide range of design philosophy and product manufacture, to provide a better mathematical insight into rationalizing the furnace operation.

Jan 1, 2004

By E. Don Dilling, W. F. Holbrook, Lloyd R. Michels, James W. Pennington, Dwight L. Harris, Wm. F. Hergert, Cyrus L. Blogett, H. A. Doerner, Ernest A. Reige

"IntroductionA process for production of magnesium by carbothermal reduction was developed at Padentheirm, Austria, by the Austro Americanische Magnesit Corporation& an independent investigation of this and other processes was started in 1937 by the Bureau of Mines at Pullman, Wash., with the cooperation of Washington State College. 10/ A preliminary study of the Radentheirm pro¬cess, as revealed by the meager information then available, demonstrated the following two major disadvantages,The use of hydrogen for shock cooling requires an enormous volume of gas - about 1,000 cubic feet for condensing each pound of metal as a pyrophoric dust which must be completely separated from this gas. Then if the gas is to be recycled for repeated use, the CO produced by the reduction reaction must be separated from the hydrogen. These separations are costly from the standpoint of equipment and operation. 11/The condensate is an impure, pyrophoric metal powder that must be purified and converted to coherent form. This is accomplished by distillation or sublimation of the metal. Distillation on a large scale involves difficulties inherent in the high boiling point (1,107° C.) and the chemical activity of the metal. To avoid these difficulties, the metal is sublimed at 600° C. and of very low pressure. This is quite easily carried out as a batch operation but is a costly procedure. A continuous sublimation process has not been accompli shed."

May 1, 1945

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By Linda Dufour

"Autoclaves have been in commercial use in the mining industry since the early 1950's the initial applications included tin, uranium, cobalt, nickel and copper extraction under both acidic and alkaline conditions. These circuits varied in batch or continuous operation. The geometry has been spherical, vertical, and horizontal type with up to six agitators, with throughput as high as 1000 stpd.Presently autoclaves are a good process selection for many refractory sulphide gold bearing ores. The first application of pressure oxidation in the gold industry was at the Homestake Mcglaughlin's Mine which was commissioned in 1985. This was an acidic pressure oxidation process treating 3000 stpd in three four compartment horizontal autoclaves 14' diameter and 53' long. Since the initiation of autoclaves for the treatment of gold bearing sulphides, there are presently 16 gold autoclaves operating worldwide varying in size up to 18'4"" inside diameter. There are seven autoclaves for the treatment of refractory sulphide gold bearing ores to be commissioned in 1997 and 1998.Autoclave technology has progressed extensively since the mid-eighties. Operational experience has made rapid progress and the result is much smoother and safer autoclave operation. There have been many advances in autoclave technology design. For example, the use of exotic materials for corrosion resistance to reduce down time for maintenance. The instrumentation involved in autoclave operation is very sophisticated which allows for many safety features. The advanced design has allowed for greater availability and as a result operating costs and maintenance costs have decreased. These technological advancements have made autoclave technology more safe and this has resulted in a greater acceptance of this type of operation. Many of the gold autoclave facilities operate up to 9 months continuously without shutdowns. The advancement of autoclave technology has inspired many new applications.Because of the outstanding operation of autoclaves in the gold industry, many other applications for autoclave technology are being considered. The following is a list of autoclave applications:"

Jan 1, 1997