Search Documents

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By Rajagopala Reddy Kallu

After the Sago and Darby No. 1 mine incidents, the new regulatory standards for the design of mine seals in underground coal mines of the United States require the mine seals to withstand higher explosion standards. This necessitated for the development of new design approaches and standards. For development of any new design standards or approaches a detailed understanding of effect of key influencing parameters on the stability of mine seal is a must. This paper attempts to address one of the factors, i.e. roof convergence, that play an important role in the stability of mine seal under explosion loading. Initially a couple of three dimensional numerical models were built and tested for different levels of roof convergence. These models confirmed that roof convergence has great influence on seal stability. A detailed study is undertaken, with some simple assumptions, to establish typical influence of roof convergence on the stability of mine seal under different levels of static explosion pressures. Three dimensional distinct element code 3DEC is used for this purpose.

Jan 1, 2007

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

By D. Harrington

Probably over 95 percent of the coal production of the United States depends upon the use of explosives before it can be placed in the railroad car at the mine, and up to the present time it has been impossible to obtain Pry kind of practicable explosive that isn't dangerous unless handled carefully. In other words, no "foolproof" explosives have been found to date and inspection of the accident records of the coal mines of this country indicates that the use of explosives in coal mines has taken a sad toll of lives. ACCIDENTS PROM EXPLOSIVES IN COAL MATES Of the 2,000 to 2,500 persons killed annually in the coal mines if the United States, 100 to 125 have been killed from explosives without an explosion of gas or dust; these accidents have been due to misfires, hangfires, premature blasts, or accidental setting off of explosives through carelessness or otherwise (but chiefly through carelessness in some form). In this type of accident the flame character of the explosive is not necessarily involved, although an unexpected or premature blast is initiated much more easily with black blasting powder, which has a long flame, than with a permissible explosive, which has a flame much shorter and of briefer duration. By far the greater number of such accidents are caused by black blasting powder or dynamite rather than by permissible explosive.

Jan 1, 1936

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By GJ Hundman

The Multiple Unit Continuous Haulage (MUCH) System was designed to provide the capacity to continuously convey coal from the mining machine to the main haulage belt. The MUCH System has an operator who steers the lead vehicle, ever following the mining machine. All the remaining vehicles follow the path of the lead vehicle, with their conveyors automatically lining up between the lead vehicle and mine section panel belt. This is accomplished by mechanical linkages on the vehicles which are interconnected by steering bars between vehicles (patent pending). The MUCH System has an operator who steers the discharge vehicle when outby travel is required. Outby travel is just like inby, with each vehicle following the path of the preceding vehicle. Surface tests overwhelmingly indicate the "UCH System should track/retrack successfully in square pillar underground room and pillar coal mines with 18 ft. wide entries and slopes up to 10 percent. For 60 degree pillar plans the minimum entry width required is 15 ft. Surface tests also indicate the MUCH System will convey over 8 TPM of coal around 90 degree corners without excessive spillage.

Jan 1, 1983

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By T. G. Joseph

Mines must manage variability from within their operations as well as those imposed upon them by external forces. This paper provides a framework to manage both internal and external variability through the review and adjustment of the mine plan where applicable to minimize lost production and maintain operational safety.

Nov 1, 2011

By G. Danko, R. Tiwari, J. Knowles

Many excavation and loading tasks require equipment operators to simultaneously coordinate the motion of multiple machine links, in order to achieve complex tool trajectories. Efficiency, ore selectivity, and machine wear, are all affected by the skill level and attentiveness of the operator. A software-based kinematics reconfiguration system designed to assist operators with various tasks has been implemented on a small experimental excavator using our new differential control architecture. Kinematics transformation and feedback control algorithms are being developed and tested using computer simulation, and the results implemented on the experimental excavator. Several task-specific kinematics transformations, including a virtual revolute-to-Cartesian machine reconfiguration and computer-assisted bucket steering and stabilization have been successfully tested. Progress, challenges, results, expected benefits, and planned work are described.

Jan 1, 2006

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By R. S. Olson

An analysis of the wash thickener-two stage filtration circuit was undertaken to quantitatively describe the circuit performance. On the basis of information developed in this study, the factors of major importance in reducing soluble loss are: filter wash, wash zone size, filter capacity, filter feed pulp dilution, blow back, filter cloth, water to repulp, water to primary wash, water to feed pulp and thickener underflow. The wash thickener-two stage filtration circuit has been used in many hydrometallurgical plants to separate solute from leach solids. As many as 20 to 30 plant operating variables determine the performance of the wash circuit and hence the soluble loss. The complex relationships of these variables, with each other and with soluble loss, make the evaluation of their effect on mill performance difficult. An analysis of this type of circuit was undertaken to quantitatively describe the circuit performance. THE CIRCUIT The diagram in Fig. 1 represents the operation of the wash thickener-two stage filter circuit. This circuit provides for counter current, cross current or for a combination of countercurrent-cross current operation. The feed pulp stream, J, is intended to include any solution or water, other than primary and secondary filtrate, which enters the wash thickener. Except for filter washing, the operations in the circuit are simple mixing operations which can be described by material balance. The concentration of solute in the filtrate and cake solution after application of wash liquor cannot be described by simple material balance. The displacement washing equation, derived by Rhodes1 and extended by Choundhury and Dahlstrom,2 appears to best describe this case of miscible displacement in porous media. In a useful form, it is

Jan 1, 1963

By A. Sutton-Pratt

The African continent has been the most prolific producer of gold since mining began. Although most of this gold has come from South Africa, other countries have also been important contributors in the past. There is currently little production outside South Africa, Ghana and Zimbabwe, but the gradual globalisation of the industry over the past decade has resulted in growing interest in the region which bodes well for its future development. An outline is given of prospects and activity (or lack of it) in South Africa, Lesotho, Swaziland, Zimbabwe, Mozambique, Madagascar, Botswana, Namibia, Zaire, Tanzania, Kenya, Uganda, Rwanda, Burundi, Zambia, Malawi, Angola, Congo, Central African Republic, Gabon, Equatorial Guinea, Ethiopia, Eritrea, Djibouti, Somalia, Sudan, Chad, Libya, Tunisia, Egypt, Algeria, Morocco, Ghana, Ivory Coast, Liberia, Sierra Leone, Guinea, Senegal, Guinea-Bissau, Gambia, Mauritania, Mali, Burkina Faso, Togo, Benin, Niger, Nigeria and Cameroun

Apr 1, 1996

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facilitate research on the fundamentals of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, but Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing adit has an advantage over an active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin in September 1936, with a crew of four laborers under a resident engineer. The laborers were recruited from nearby farms, and although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By Theodore R. Maynard

The history of foundation engineering in Chicago is a tale of innovation, made necessary in order to keep pace with structural technology which allowed taller buildings with heavier bearing loads, to accommodate a non-conducive geologic setting. The geology as it relates to foundation construction and underground construction in general is briefly described. A chronology of important events from the birth of Chicago to the present is presented. The impact of various construction techniques which were either initiated or refined to allow the growth of Chicago are discussed. Introduction The growth of Chicago resulting in today's high-rise high-density population center can be looked upon as a history of modern underground construction. The two major reasons which explain this are 1) It grew up during a period of rapid development in the Industrial Revolution and 2) Its natural geological setting needed a great deal of innovation for continuing growth.

Jan 1, 1991

By David E. Thompson, Andrew F. McKown, Herbert H. Einstein, Amr S. Azzouz

INTRODUCTION Design of supports for underground chambers in rock has undergone considerable development. This becomes evident when comparing support dimensions of subway station caverns built in the U.S. over the past fifteen years. The Porter Square Station cavern, which is a part of the Massachusetts Bay Transportation Authority (MBTA) Red Line extension, is the latest in this series. It is approximately 168 m (550 ft) long, 21 m (70 ft) wide, and 14 m (45 ft) high, and has a permanent support of light steel ribs imbedded in a 0.4 m nominal (15 in) shotcrete lining. An extensive construction control instrumentation program made it possible to evaluate the performance of the cavern and its support. This evaluation, which is presented in this paper, was the objective of a research project sponsored by the Urban Mass Transportation Administration (UMTA) and jointly conducted by Haley and Aldrich, and MIT. The actually used design procedure was compared with other approaches, notably procedures based on Finite Element analyses and empirical rock mass classification methods. Support dimensions predicted with all these approaches were compared to the actual support and its performance.

Jan 1, 1983

By Galen G. Waddell

Dilation and contraction of the rock surrounding horizontal access open-ings of a deep mine were analyzed during stope advance to determine what type of measurements, made with relatively inexpensive instrumentation, would best reflect the rock behavior. A variety of instruments, mostly mechanical extensometers, were used. Detailed descriptions are given of Down-the-hole extensometers, floating rockbolt clusters, transit surveys, and other instruments and measuring techniques. Although all of the radial-deformation-rate graphs illustrated useful rock behavior data, the most informative graphs were compiled from data procured with the radial extensometers that penetrated, to various depths, the rock around the access openings. An analysis is given of measurement data on the rock around lateral drifts and across and adjacent to the nearly vertical vein of the Star mine, Burke, Idaho. Several useful relationships were found between the rock deformation rate and the stoping process. Information was produced on the elastic state of rock around an underground opening, effectiveness of stope support, rheology of rock, zone of influence around stopes, effectiveness of rockbolts, axis of maximum strain in a plane perpendicular to the long axis of the lateral, and other phenomena. This information could be of particular value in determining location, design, and support of underground openings.

Jan 1, 1966

By S. E. Olsen, K. Tang

The complex heterogeneous equilibria associated with the production of manganese ferroalloys have been simulated by employing recently developed thermochemical databases. The non-ideal Mn-Fe-Si-C alloy and the MnO-SiO2-Al2O3-CaO-MgO-FeO slag system have been modelled separately by the compound energy and cellular model. A large number of experimental thermodynamic and phase-equilibrium data were used to evaluate the model parameters for the liquid and solid Mn-Fe-Si-C phases. In addition to the liquid metal phase, solid mixture phases occurring in the Mn-Fe-Si-C system have also been studied. Over 500 measured equilibrium data have been utilised to verify and calibrate the model calculations. The paper will present typical simulation results, from activities of components to multicomponent heterogeneous equilibria. Good agreements can be obtained for many important technological parameters such as carbon solubility, phase relations and equilibrium diagrams, element distribution as function of temperature and slag composition etc. Application of the present models to the silicomanganese production will be demonstrated in this paper.

Jan 1, 2004

By Maurizio Siepi

The realisation of most of the civil engineering works is subordinate to the execution of consolidation works, in order to improve the soil physical-mechanics characteristics. The works classifiable with the term "Soil Improvement" can be realised using several technologies, among which the Deep Mixing Method is distinguished for his remarkable flexibility and productivity characteristics. The Deep Mixing Method is a process whereby a rotary drilling machine mechanically drills a constant diameter hole while cement slurry is injected into the soil at high pressure. The process combines state of the art construction techniques merging mechanical and hydraulic mixing energies at the tool bit. The result is a soil-cement column of engineered strength, consistency and dimension. Whereby the soil cement column formation process is controlled by a computerised device, the result is a speedy installation, thorough mixing, and a high degree of control, repeatability and documentation.

Jan 1, 2002