Search Documents

By Robert L. Parsons

This paper describes the results of a detailed analysis of a loess deposit at the deep foundations test site established by the Kansas Department of Transportation. Multiple CPT, SPT, and pressuremeter tests were conducted as part of the investigation. This paper includes an evaluation of the effectiveness of common correlations used with the CPT, SPT when used for classification of loess and estimating its properties. Results show that common correlations must be used with caution as significant errors in estimation may result from using methods developed for other soil types. Laboratory testing included direct shear, triaxial, collapse, and consolidation testing, with many of the tests conducted on both vertically and horizontally oriented samples to evaluate anisotropic behavior. The results showed that strength properties could be considered to be isotropic.

Jan 1, 2009

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Cesar Sáenz Acosta

El presente texto señala las mediciones de impactos que se han realizado a los programas de responsabilidad social de una empresa minera. Esta medición se realizó a través del cálculo del indicador “Retorno social de la inversión”, aplicando el modelo SROIM o Gestión del Retorno Social de la Inversión. Los proyectos de RS medidos permiten actuar a las empresas de manera responsable con su comunidad y comprenden: salud y nutrición, educación y desarrollo económico. Asimismo, esta medición contribuye a mejorar la comunicación de los impactos generados y desarrolla una gestión adecuada de estos.

Sep 12, 2011

By James D. Nickerson

Thee Brightwater water treatment facilities, currently scheduled to be completed in 2010 and begin operating in 2011, will serve the northern part of King County, WA. The facility includes a new treatment plant and extensive conveyance system consisting of more than 21 km (13 miles) of influent and effluent conveyance tunnels and five portals. The majority of the conveyance system tunnels are mined by tunnel boring machines (TBM) and microtunnel boring machines (MTBM). Tunnel and portal construction is divided into three main contracts. The Ballinger Way receiving portal, constructed under the central tunnel contract, is the terminus for the BT-3 leg of the central contract and the BT-4 terminus of the west contract. The shaft has a 7.3-m (24-ft) finished inside diameter (ID) to accommodate removal of the central project TBM and the west contract TBM and extends to a depth of 66 m (216 ft) below grade through a complex and challenging soil profile characterized by multiple ground water tables. Vinci Grand Projects/Parsons/Frontier-Kemper Constructors (VCFK) was the joint venture team for the Ballinger Way portal. Frontier-Kemper was responsible for the shaft sinking. VCFK evaluated either slurry wall techniques or ground freezing for earth support during excavation of the portal and liner installation. The selection process took into account the vertical depth, cost, past practice, geology, water tables and a 9-m- (30-ft-) thick zone of contaminated soil at the top of the shaft. Ground freezing, which would also act as a hydraulic barrier, was deemed the better option for this project. The contract was awarded to New Jersey-based geotechnical contractor Moretrench. Typically, frozen walls, by design, key into an underlying cutoff. At the Ballinger Way portal, however, the [ ] freeze bottomed out in a substantially thick stratum consisting of predominantly clay, but with some inclusions of permeable soil that indicated significant ground water pressures. To ensure stable conditions at the bottom of the shaft, Moretrench, which also specializes in dewatering, designed and installed a perimeter array of deep wells to temporarily depressurize the permeable soils. The movement of ground water generated by pressure

Jan 1, 2009

By J. P. Josien, J. F. Noirel, F. Lahaie, P. Bigarre, M. Al Heib

ABSTRACT: In June 2001, a fatal rockburst affected a longwall face in the Houillères du Bassin de Lorraine (HBL), France. Subsequently, a large operation of in situ stress measurements by overcoring was carried out with two main objectives: providing input data for the back analysis of the dynamic event and characterising the stress field in the next panels to be mined for identifying other potential high-risk zones. This paper makes a synthesis of the results of the overcoring tests performed and discusses those results in connection with the mining context, numerical model predictions, laboratory rock test results and microseismic activity. KEY WORDS: Mine, rockburst, stress, overcoring, measurement. ZUSAMMENFASSUNG: Im Juni 2001 hat ein Bergschlag eine Kohlengrube des Houillères du Bassin de Lorraine (HBL, Lothringen, Frankreich) schwer beschädigt. Nach diesem Unfall sind Spannungsmessugen durch Überborung durchegeführt worden, mit zwei Hauptziele : 1/ Daten zu liefern für die Retro-analyse des dynamischen Gebirgsschlag und 2/ die Spannungen in den zukünftigen Ausbauen so gut wie möglich zu charakterisieren, um eventuele andere Risikozonen festzustellen. Dieser Artikel stellt eine Synthese der erzielten Ergebnisse vor. Er diskutiert diese Ergebnisse in Verbindung mit dem gesamten Kohlengruben Zusammenhang, mit den Ergebnissen von numerischen Modellierungen, mit der Labor-Charakterisierung und mit der microsismische Überwachung. SCHLÜSSEL-WÖRTER: Kohlengruben, Bergschlag, Spannung, Überborung, Messung. RESUME: En Juin 2001, un coup de terrain a gravement affecté une longue taille aux Houillères du Bassin de Lorraine (HBL) en France. A la suite de cet accident, une importante campagne de mesures de contraintes par surcarottage a été réalisée, avec deux objectifs majeurs : fournir des données d’entrée permettant la rétroanalyse du phénomène dynamique et caractériser au mieux le champ de contraintes dans les futurs panneaux exploités afin de détecter d’éventuelles autres zones à risque. Cet article présente une synthèse des résultats obtenus, et discute ces résultats en liaison avec le contexte d’exploitation, les résultats de modélisation numérique, de caractérisation en laboratoire et de surveillance microsismique. MOTS CLES: Mine, coup de terrain, contrainte, surcarottage, mesure.

Jan 1, 2003

By J Williamson, M Griessmann

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Watershed tungsten deposit is located in the Hodgkinson Province of north Queensland, Australia. The deposit is hosted by Siluro-Devonian flysch-type meta-sediments of the Hodgkinson Formation, which were subjected to four major deformation events. Mineralisation has occurred syn- to post-D4 and is related to the intrusion of S-type granitoids of the Permian Whypalla Supersuite.Watershed is located within a regional NW–SE-striking melange zone composed of brecciated and intermixed arenites and shales. The major NW–SE-striking Tullah fault zone is situated in close proximity to the east of the deposit.The Watershed deposit occurs within a tightly folded upright anticline with NW-plunging fold axis. The anticline contains a major package of coarse-grained to conglomeratic arenite, which harbours the Watershed mineralisation. Several alteration styles occur within the arenites, of which Fe-poor calc-silicate alteration dominated by clinozoisite/epidote is the most significant. Less widespread but locally important alteration styles comprise garnet-dominated calc-silicate alteration, albitisation and sericitisation. The arenites are enveloped by unmineralised carbonaceous shales and shale breccias.Tungsten mineralisation occurs solely as molybdenum-poor scheelite and can be found as three styles: disseminated mineralisation in calc-silicate altered arenites, vein-style mineralisation with quartz-albite-scheelite veins and minor but high-grade mineralisation in albitised felsic dykes.Contact metamorphic rocks and geophysical data indicate the proximity of an underlying granitic body. It is believed that this granitic body was the main driver of the hydrothermal system generating the Watershed deposit. An early mineralisation stage caused the selective calc-silicate alteration of the arenites, while a second stage caused the vein-style high-grade mineralisation. The folded shales enveloping the arenites worked as an effective barrier that kept the mineralising fluids in a confined rock volume.The scheelite mineralisation at Watershed is open to depth, with a granite-hosted porphyry or greisen-style mineralisation anticipated below the current resource.CITATION:Griessmann, M and Williamson, J, 2015. The calc-silicate-hosted Watershed tungsten deposit, far north Queensland, Australia , in Proceedings PACRIM 2015 Congress, pp 545–550 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Helga Larravide

A new on-line database of literature about copper has been created through a joint undertaking by the Copper Development Association Inc. and PROCOBRE-Chile, with funding provided in part through the International Copper Association, Ltd. The new database will permit Spanish-speaking technologists to access publications maintained by PROCOBRE-Chile by means of standard keyword searches. In addition, a new Spanish- English thesaurus has been written to enable Spanish-speaking individuals to search d access the Technology and Environmental databases of the Copper Data Center, which together comprise more than 80,000 publications dealing with the production, properties, uses and environmental effects of copper. Planned expansion of the new Spanish literature database is described.

Jan 1, 1999

By Martin C. Jones

This paper outlines the development of small diameter grouted piling, to deal with foundation problems in difficult soils conditions and in very restricted access areas. A number of applications are outlined to show the way in which these piles have been used over the last sixteen years in Canada. PICKERING GENERATING STATION - ONTARIO HYDRO UNDERPINNING OF SCREENHOUSE - TRASH DISPOSAL AREAS Between 12th July and 29th September 1971, 40 small diameter grouted piles were installed in the screenhouse at Pickering Generating Station. Access was extremely restricted as the screenhouse had been completed and the majority of mechanical equipment had been installed. The two ends of the screenhouse had been built on granular fill which overlies till and shale bedrock and settlements had been observed which it was decided had to be halted even though the rate of subsidence had decreased. Two diamond drills were employed to install 8 inch

Jan 1, 1987

By Pengfu Tan

A program ?SlagVis? has been developed to simulate the liquidus temperature, phase compositions and viscosities of ZnO-CaO-SiO2-Al2O3-?FeO? slag, such as Imperial Smelting Furnace (ISF) slag and lead blast furnace slag, combined with F*A*C*T slag database and the mathematical model of slag viscosities based on a modified Urbain formalism. The modeling results have been validated by a number of measurements. The effects of slag compositions on viscosities of ISF slag and lead blast furnace slag have been simulated and discussed.

Jan 1, 2005

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

The labour question is one that has caused mine managers much thought and anxiety and is likely to continue to do so as long as human beings exist. The difficulty is to devise some arrangement whereby the interests of miner and mine ownerare identical. Mines cannot be worked without capital, and capital is no good without labour, yet, though both have the mine in common, their interests are not exactly the same. Some men are happy so long as they can scrape through by exerting themselves as little as possible, but capitalists do not work mines for charity, they want some return for their money.Where a large number of men are employed there are bound to be examples of all sorts, good and bad, and it is because one cannot depend on all, that different methods of employment have to be adopted. Which method is selected depends to a great extent on the labour market, local conditions, nature of the ore and the way in which it occurs.A big step towards success is obtained by securing the services of good bosses, not only those who know how work should be done, but men who have a knowledge of human nature. It is a big mistake to be too lenient with a man, also to be unnecessarily harsh. A good boss will always be sought out by good men who have worked under him before, or who have heard of him from others. By a good boss we do not mean one who employs two men where one would do, or who lets the men loaf...

Jan 1, 1901

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

The treatment plant at Martha Mine was upgraded from a nominal throughput of 110tph (O.93mtpa) to 150tph (1.25mtpa) late 1999. Post-upgrade performance did not meet expectations when treating either the competent primary ore or the clay-rich oxide ore.   ò Plant throughput is constrained by milling capacity when treating the competent primary ore. This is not an issue at present as current plant feed is oxide ore from the top of the open-pit, but will become so in future years as the pit deepens. To counter this future threat, ball mill power has been restored to 1100kW through modifications to the drive train. The addition of a crushing circuit may also be necessary.   ò Plant throughput was originally constrained by thickener and leach/adsorption tank issues when treating the oxide are. Changes to plant equipment and operations has seen the removal of these constraints and throughput on this material is no longer a problem.   The most significant issue facing plant staff at present is the high silver grade and its impact on gold recovery. These high grades impact upon recovery through losses caused by insufficient leach and adsorption capacity. To counter this, the geology, mining, and milling teams are working together to blend the high grade silver zones with lower grade ores - this is seen to be the quickest and most cost effective way to deal with the issue. The plant design has also been evaluated with a view to modifying it to cope with the higher silver grades. The viability of these modifications will depend on cost and time (that is, the length of time to implement any modifications versus the length of time to mine out the high silver zones).

Jan 1, 2001

By Cz. Mora, A. Pawelczyk, D. Hreniak, P. Nowak, A. Dyonizy, S. Strek, W. Strek, K. Grabas, A. Ostrowski

Globalization and a growing demand for limited raw material resources have forced changes in the approach to the supply chain. This is particularly true in the case of rare earths, which are regarded as one of the most important development indicators of modern technologies. To ensure a secure supply of commodities, the European economies have been prompted to investigate REE recovery from sources which until recently, for technical or economic reasons, were considered not sufficiently attractive. An interesting example is apatite phosphogypsum waste dumps. The REE content in these waste dumps averages around 0.5-1 %. One of the most important phosphogypsum locations in Poland is the Lower Silesia region where a phosphoric acid Chemical Plant "Wizów" operated for several dozen years. In this work, rare earths are leached from the phosphogypsum crystalline structure by a chemical treatment and can then be separated into individual chemical compounds. The technology used in these recovery tests, matches up to a coherent European raw materials policy supporting effective management of resources and promoting waste materials recycling.

Jan 1, 2014

By J. -F. Lessard

Most underground mines rely on ore pass systems to ensure the transport of ore and waste. The design and operation of ore pass systems often rely on past experience, which is often anecdotal and at times contradictory in nature. This paper summarizes the current practice in Quebec underground metaliferous mines. The information was collected during a series of site visits in ten underground mines. The database includes information on ore pass configuration, support, materials transited, and overall ore pass performance.

Jan 1, 2006

By G. Gomez Ciments-Calcia

The sources of complaints by neighbours of the operating quarry are due to the 3 following causes : - Impulsional noises or air hoch wawes – Vibrations - D u s t How a blasting in a quarry operation is felt by neighbours cannot be measured solely by the various limits set by national and European regulations regarding vibrations and air shock waves (sound pressure).

Jan 1, 2002

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008

Nowadays, technology has improved to extract dimensional stone blocks at quarry sites and also to process these at processing plants for making slabs and tiles. In the process of quarrying and processing, performance evaluation of machinery is very important to achieve optimum output at minimum cost with improved technology. Cost analysis of improved technology includes parameters such as manpower, energy consumption, tool consumption, depreciation, maintenance and also others. The chainsaw machine with long boom and rail in marble quarries and multi-diamond wire saw machine for slab making from granite blocks at processing plants have recently been introduced in India. Thus, a study was carried out under a research project on these machines to assess their suitability. In this paper, performance evaluation and cost analysis of chainsaw and multi-diamond wire saw have been carried out with existing machines on the basis of research findings.

Dec 6, 2010

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magnetohydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2015

By Phillip J. Mackey, Gerardo R. F. Alvear F.

It is now 38 years since the publication of the first edition of "Extractive Metallurgy of Copper" by Professor W.G. Davenport and the late Professor A.K. Biswas. The text book would be issued in a total of five editions, soon became the standard for students and those in industry. Interestingly it was published at the onset of great change in the industry. This was a time when sulphur dioxide controls in the USA were introduced, and almost simultaneously, world oil shocks caused significant increases in the cost of fuel - all leading to efforts to adopt new technology and move away from the reverberatory furnace, which had no potential for sulfur capture and required large amounts of fuel. At the time of publication of the book, new processes such as the Noranda Process and the Mitsubishi Process were in their infancy, while flash smelting (which was first commercialized in 1949 at Harjavalta, Finland) had made significant in-roads in boosting copper output, with some 22 new flash smelters licensed by 1976. Computer technology and associated process control techniques were rudimentary compared to systems today, available physico-chemical data remained largely in tabulated format and needed to be manually entered into the main frame computers of the era, while modeling techniques common today had not yet been developed. The copper industry has therefore seen immense changes since the time of this textbook: world tonnage of smelted copper has risen from 7.34 million tonnes/year in 1976 to 16.7 million tonnes/year in 2012, over a two times increase. Technologies such as the El Teniente Process, or Top Submerged Lance technologies, typified by the ISASMELTTM, not commercialized at the time, now treat large tonnages of copper concentrate in a single furnace. Advanced heat and mass balance software and thermochemical modeling are now used extensively to examine chemical and physical characteristics for process design and to support process optimization. These changes in the industry have been chronicled in subsequent editions of the book. This paper looks at the issues and problems seen in 1976 and over the intervening years, and compares this with the challenges facing the industry with the available tools and technologies today. Some ideas looking into the future are also discussed in the paper.

Jan 1, 2014