Search Documents

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024

By Peter Bigwood

Whether drilling through tough clay or breaking rock, or facing the most severe conditions including mixed face ground, perched water and running and flowing sands, working under-ground certainly comes with no shortage of challenges. In an environment where the unknown is faced on a daily basis, tunneling contractors must be able to rely on their equipment to get the job done properly. Not only that, their equipment must comply with two of the highest priorities: safety and efficiency. In addition to being the number one concern, a proven safety record provides additional benefits to a company. A safe work environment serves as a key component to company growth, including the ability to remain competitive in bidding and maintaining higher-level, more challenging projects.

Jan 1, 2012

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By Harvey Parker

This is part two of an article on the prominent role that the United States and its industry leaders have played on the International Tunnelling and Underground Space Association (ITA), which represents the underground construction and underground space industries worldwide. The U.S. is officially represented in ITA by UCA of SME. (Part one is in T&UC, June 2007, pp 39-42) Tunnel advances in 1960s and 1970s The 1960s and 1970s were active and productive times for the U.S. tunneling industry. During that time, federal programs, sponsored by the Federal Railroad Administration (FRA), the Office of High Speed Ground Transportation (OHSGT) and the Advanced Research Projects Administration (ARPA), stimulated tunnel research and development. Also, the American Society of Civil Engineers (ASCE) and SME collaborated to create the Underground Construction Research Council (UCRC) and the Rapid Excavation and Tunneling Conference (RETC) series.

Jan 1, 2007

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By Sheridan A. Glen

As the Federal government along with individual states continue to grapple with the job of refining a comprehensive energy policy, coal continually stands out as an energy source which heralds a combination of old and new capabilities like an energy planners prophecy, but which is plagued with serious environmental constraints. To determine what level of coal utilization is ultimately possible for states East of the Mississippi, whose high sulfur content coal presents the most paramount of challenges, one must consider product availability, via existing transportation modes, the developing industrial markets and the ability of coal to meet the challenge of becoming an environmentally acceptable fuel. Gasification is emerging as a form of utilization, which during the next twenty years stands a good chance of being able to meet the challenge of making coal an environmentally clean, easily transport-able and usable fuel. It can be argued that, of all the potential ways of utilizing high sulfur coal, coal gasification is perhaps the most expensive, the most financially risky and carries environmental liabilities of its own. Synthetic gas and oil markets will undeniably be a function of price and demand, which, for the purposes of this paper, I'm assuming will begin to merge in the late 1980's and into the 1990's. This is also presuming that public utility commissions will allow favorable price structure ruling so that gasified coal products can be rolled into their respective rate base, much the same as synthetic natural gas from petroleum by-products are currently being priced. The comparative economic markets of coal to gas pro-duct have plenty of time to mature. There is an approximate twelve-year lead time needed to bring coal gasification plants on line which will be able to compete in the market place for natural gas and oil customers.

Jan 1, 1977

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

By Edgardo Fogli, Mario Lampiano, Antonio Nicola

The project is located in the northern region of the People’s Republic of China and was awarded to Impregilo, as sponsor of the Wan Long Joint Venture, in September1997. The project consists of four tunnels for a total length of 88,700 m, with an excavation diameter of about 4.9 m. The lining is made of honeycomb pre-cast segments, connected by PVC dowels and the joints are sealed with elastomeric gaskets. The geology is mainly Limestone, Dolomite and Sandstone. Karst cavities are abundant and are often in-filled with plastic red clay. This has adversely affected the TBM’s progress. Four double shield telescopic TBMs were mobilized to cope with the very tight construction schedule and, at the end of November 2000, more than 80% of the tunnel has been bored. The article analyses the TBMs’ productions in the various geological conditions and the results of different technical solutions adopted at the project.

Jan 1, 2001

By K. E. Kolm, W. H. Langer

Developing natural aggregate resources (sand, gravel, and stone) creates environmental impacts. A systems analysis method has been designed to characterize the components of the environmental system, identify potential impacts to those systems, and evaluate the extent of those impacts. The step-wise method consists of problem definition, data collection, preliminary conceptualization and characterization, additional data collection, data analysis, and refinement. The method requires analyzes of various systems making up the environment, including land surface, geomorphic, subsurface, and groundwater systems. After system characterization is complete, the method focuses on identifying and evaluating potential environmental impacts to determine acceptable mining strategies.

Jan 1, 2001

By John L. Bolles

The Phelps Dodge Corporation's Morenci Concentrator includes facilities for coarse crushing, fine crushing, grinding, flotation, tailing, disposal, concentrate filtering, and drying. The Morenci Concentrator daily throughput is in excess of 60, 000 tons. The ore milled is mainly a medium-hard monzonite porphyry in which the principal sulfide minerals are chalcocite and pyrite. The ore is transported by rail from the Open Pit Mine to the primary crushing plant located at the concentrator site. Ore is side-dumped from 80¬ton railroad cars into a sixty-inch gyratory crusher. The ore is then conveyed to a. 12, 000 ton coarse ore storage bin. Fine crushing is accomplished by four parallel lines of conventionally stacked crushers in open circuit. Each unit consists of one seven-foot standard cone followed by two seven-foot shortheads. Ti% product of the fine crushing plant is distributed by two tripper cars across a fine ore storage bin. The crushed ore is then fed by variable speed belt feeders into thirty parallel, single stage, closed circuit grinding units. Each of the 30 grinding units consists of one 6' x 23' conditioning drum, one 10' x 10' ha l mill and two 54" duplex spiral classifiers as principal equipment. The dry ore is fed into the conditioning drum with water to dilute the ore to a slurry of approximately 78% solids by weight. An aqueous solution of ammonium sulfide is also added to the conditioning drum. The ammonium sulfide primarily acts as a sulfidizing agent. The ore slurry containing the naturally occurring sulfide copper minerals and the sulfidized copper minerals discharges into the feed scoop box of the ball mill, where milk of lime, collector and-.dilution water are added. The ball mill product slurry is gravity fed: to the classifier pool where water is added to obtain the desired classifier overflow product

Jan 1, 1977

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By John Heter

An alum/sulfur deposit (USDA organic registered) was mined underground for alunite (K,Na) Al3 (SO4)2 (OH)6 from the early 1900s to the 1930s. It is now being mined as an open pit quarry. A larger assemblage of minerals is included with this method (Alunite, Potassium?Alum, Jarosite, Gypsum, Native Sulfur and K-feldspar). This assemblage of minerals provides the necessary requirements as a Volcanic Soil Conditioner Sulfur-Potash. Heart of Nature? Company has been marketing this product to farmers on the west coast as a (1) pH reducer, (2) soluble sulfur and potassium source for plant growth and (3) soluble calcium. Recently, a new market has been tapped. This product has been found to solve many odor, bacteria and algae problems faced in the dairy industry.

Jan 1, 2008

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986