Search Documents

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala's Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala's cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala's Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976

By T. L. Heisler

The Cigar Lake project, located in northern Saskatchewan (Figure 1), is one of the world?s largest high grade uranium deposits, with reserves of 150 million kilograms of uranium in a deposit averaging 430 metres below the surface. The Cigar Lake project is being developed by Cigar Lake Mining Corporation (CLMC) which is owned by Cameco Corporation (48.75%), Cogema Canada (36.375%). Idemitsu Uranium Exploration Canada Ltd. (12.875%) and Korea Electric Power (2%). Mining the Cigar Lake orebody is presenting a very real challenge due to the high grade and the ground conditions in and around the orebody. Presently, an underground test of various mining methods is underway.

Jan 1, 1992

By Frank Hagar, George M. L. Robinson

INTRODUCTION Mine waste monitoring and management is essential when the industry is being required to accept the environmental liability for all generated, stored and disposed solid and hazardous waste. Environmental regulations mandate the operator to minimize waste production while requiring the operator to cleanup existing contamination. Since these requirements are being enforced, many operators do not have a clear under- standing, whether their existing operation will or could be required to adopt remedial plans to mitigate off-site contamination impacts. The following methods, using conventional and advanced geostatistical methods, provide a tool to make appropriate assessments whether existing or potential contaminant issues are present. BACKGROUND Generated solid wastes from mining operations are currently exempt from Solid Waste Disposal Act (SWDA) Sub- title C (RCRA), statutes and promulgated regulations, however, compliance with SWDA Subtitle D statutes and regulations is required. In order for the mining operator to be exempt from hazardous waste regulations, the operator must demonstrate that generated waste does not have hazardous waste characteristics. In many instances the operator will be able to use statistical tools and their existing data to determine whether their site could be a potential hazardous waste liability. METHODS The following statistical and geostatistical methods can be used to determine whether existing wastes could be a regulatory concern. The following presents a brief discussion of standard statistical methods and discusses, in greater detail, how advanced geostatistical tools can be used to define potential waste issues. The following will discuss how data can be screened, "Data Filtering and Reporting"; how data can be evaluated using "Conventional Statistics"; followed by a detailed discussion o f "Geostatistical and Estimation Techniques" and "Statistical Modeling". Data Filtering and Reporting Data filtering is the simplest, but potentially the most powerful statistical tool because data can be easily sorted to meet regulatory reporting requirements. Filtering includes unions and intersections of data such as date, maximum and minimum values of one or several variables. Using the data base presented in "Mine Waste Data Base Management Procedures", Robinson and Hagar, 1987, an example of a filter group is presented.

Jan 1, 1987

By K. Biswas

In general, it cannot be assumed that the strength of coal pillars remains constant over long time periods. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing load-bearing capacity of the pillars. This paper discusses a unique approach to determine the time dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15 and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar and the strength profiles were determined for each hole using the Borehole Penetrometer. The strength data were treated statistically to establish time dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 1999

By D. Hongjun

In this paper, the flotation rule and behaviors of kyanite-group polymerphous minerals were studied in modified Hallimond tube in detail. Furthermore, the energy change of collector/mineral systems before and after adsorption and the net charge densities of the atoms on the minerals surfaces were calculated by use of quantum chemistry. The flotabilities in minerals were successfully explained.

Jan 1, 1995

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By Werner Wenzel

Methods to increase the gas penetration through sinter layers. In the field of agglomeration, sintering has gained importance, specially in Europe; in Best-Europe this trend will continue till the year 1980, since it is quite probable that in the blast furnace burdens with 50-60 sinter, 10-20 % pellets and 20-25 % ore lumps will be employed. In order to meet this demand for sinter, new sinter bands with reaction areas between 300-400 m2 will be constructed. Chemical and physical phenomena during the Suction-Draught-sinter process. Iron ore sintering is generally considered as a burning process where the material contains 90-95 % ash i.e. non-combustible ingredients. Sintering represents a heterogeneous exothermic reaction in which the chemical phenomena as combustion, calcination, hydration, reduction and oxydation are superposed by physical phenomena. The physical phenomena are devided into material transport and simultaniously occurring heat transport processes. The velocity of these combined physico-chemical reactions i.e. the change in the reaction site per unit time determine the efficiency of the sinter process. The gas permeability as an important criterion of heat transport during the Suction-Draught sinter process.

Jan 1, 1971

By Richard W. Kimball, Fred B. Estep, Dwayne E. Easterling

This paper discusses the overall challenges to construct a 15,125.7 m (49,625 LF),wastewater drainage tunnel in Cobb County, Georgia by a joint venture of Gilbert Southern Corp. and S.A. Healy Co. and a construction manager Parsons, with Jacobs Associates as a subcontractor. The goal of the project is to provide wastewater retention during peak usage and is connected to a treatment facility near the Chattahoochee River. The primary component of the project is the TBM-driven hard rock tunnel. Additional works include drill and blast areas; four intake interceptors, two construction shafts and a 33.5 m (110 ft), diameter pump station shaft.

Jan 1, 2003

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By Lawrence M. Brennan

Early in 1971 the Peabody Design and Preparation group began engineering on a preparation plant which was to process eight mil- lion tons per year of raw coal. For the first five or six years this product was to be furnished 50% from surface mining operations and roughly 50% from underground operations. By early 1980, 1008 of the production was to come from underground mines. Because of the large annual commitment from Randolph Preparation Plant, it was essential that the plant operate with minimum down-time. As usual, capital costs were to be kept at a minimum. Before we discuss the details of design, it would be best to discuss the overall picture. Underground production to be pro- cessed through Randolph Preparation Plant was to be delivered by means of one mile overland conveyor from Baldwin #1 Underground Mine to the plant. Surface Mine production was to be delivered by means of 100-ton haulage units dumping in a 1,000-ton capacity hopper. Because of the changing production rates in both the underground and surface mines as well as the great difference in size consist, it was decided that it would be necessary to divorce the plant as much as possible from production. For this reason, twin 6,500-ton raw coal silos were constructed to separate the two coals as well as allow blending. The preparation plant itself, was to be designed to Operate two shifts per day, five days per week, at an average rate Of 2,200 tons per hour with a maximum rate of 2600 to 2800 tons per hour. Coal was to be delivered to our customers by means of rail haulage at both unit train rates and plant process rates. The surface mined coal, after discharging into the 1,000-ton R.O.M. hopper, is fed by means of two 72" wide reciprocating feeders onto a 72" wide steel cable belt. The steel cabled conveyor discharges the R.O.M. coal onto a fixed grizzly, scalping out a percent of the 6 x 0 coal. The balance is fed to a 12' x 27' Rotary Breaker. The material passing through 6" round hole screens is added to the 6" x 0" from the scalping screen. The 6" x 0" is conveyed to the top of one of the 6500 ton silos designated for surface coal. Material that is not broken to pass the 6" breaker screen is discharged to a bin and disposed of with plant refuse.

Jan 1, 1976

By P. Michael

Proponents of geomorphic mine land reclamation have criticized current reclamation practices in the coal fields of steep-sloped Central Appalachia as too narrowly focused on civil engineering principles and neglectful of the functional and aesthetic benefits of reclaiming mine sites in ways that mimic natural landforms and drainage patterns. They observe that current mining and reclamation practices are radically transforming the mountain-and-valley terrain into gigantic flat plateaus and, in doing so, disrupting the beauty and ecology of the natural landscape. Instead of designing and constructing linear or planar surfaces and unvarying slope gradients during the reclamation process, they recommend ?landforming,? i.e. the adoption of curvilinear, compound slope forms that blend well with the surrounding physiography and represent the result of naturally stabilizing geomomorphic processes. The authors feel that the concept of geomorphic mine land reclamation is sound, however, its application to the Central Appalachian coal fields faces significant--albeit not insurmountable--challenges. They include: (1) existing reclamation enforcement regulations that are focused on civil engineering principles and not explicitly supportive of geomorphic methodologies; (2) regulatory agencies? current intent to limit the down-gradient reach of excess spoil fills in order to allay disruption or burial of natural streams; (3) actual or perceived increases in reclamation costs; and (4) the challenge of designing and constructing ?natural? landforms that are mature and stable in an otherwise youthful, erosional landscape.

Jan 1, 2010

By G. V. Henderson

Limestone and Dolomite quarries located near Salto-De-Pirapora, Arroia Grande Gaucho, Conde Francisco and Candioita probably represent the closest, major sources of high quality lime and cement grade carbonate rocks to the major population center of Sao Paulo Brazil. The nearest major city to most of the limestone - dolomite sources is Sorocaba and Palma. All of the mining properties visited during this study are located in the state of Rio Grande Do Sul at approximately -32 degrees south latitude and -52 degrees west longitude, southwest of the major port city of Porto Alegre.

Jan 1, 1981

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By J. Scheepers, P. Smith, G. (Yunfei) Qiao

High pressure acid leach (HPAL) and pressure oxidation (POx) or pressure leaching extraction processes occur in autoclave vessels operating at elevated temperature and pressure, acidic conditions with abrasive mineral slurries. The harsh process conditions require specialized severe service metal seated ball valves to support operation of the vessels. Over several decades thermally sprayed titanium dioxide (TiO2) and chrome oxide (Cr2O3) coatings have been applied to extend the service life of the ball valves and other high wear critical components. Variability in the coating application quality control and severe process conditions can result in spalling, coating failure and premature failure of the component resulting is decreased autoclave circuit availability. In 2012 MOGAS, together with BRENCO, initiated research and development for ML-381, metallurgically bonded coating. This paper includes the historical development of severe service ball valve coatings, success of the trials and increasing industry adoption of the ML-381 coating for ball valves and other critical autoclave circuit components.

Mar 2, 2022

By Eleanora I. Robbins, Motoaki Sato

Many problems associated with acid mine drainage (AMD) are caused by the complex way molecular oxygen (O2) oxidizes reduced matter at surface temperatures. In aqueous solution, O2 kinetically "prefers" to go through the formation of hydrogen peroxide (H2O2) as an intermediate. Being innately unstable, H2O2 is quickly decomposed back to water and oxygen in the presence of dissolved Fe and Mn, both catalysts for the decomposition. Direct addition of H2O2 to AMD produced similar results. Ozone (O3) is a much faster and stronger oxidizer than either O2 or H2O2. In the laboratory, O3 rapidly precipitated Mn, Fe, Ni, Co, Pb, and Ag even in acidic solutions. The experiments indicate that AMD can probably be processed with ozone and metal oxides/hydroxide recovered in flow systems using only septic-tank-size reactors and small sedimentation ponds.

Jan 1, 2000

By Tom Michaud, Rob Albinger, Ian Turner, Michael Rispin

Data transmission, communication, tracking, and the connection of equipment such as gas detectors, cameras, and collision avoidance systems in today's tunnel industry are critical pieces of the constructor's infrastructure. Reliability, flexibility, redundancy, and cost-effectiveness are key in selecting and implementing inte- grated systems. Both wired and wireless components are used to deliver custom solutions and can involve interconnectivity between backbones. Systems integration is important as industry adopts proven technologies from other industries. Case stud- ies are given showing how tailor-made approaches deliver needed functionality, with varying degrees of com- plexity, in various classifications of environment, in order to meet a project need.

Jun 23, 2024

By G. Wayne Clough

During shallow tunneling in an urban environment, deposits or pockets of saturated soil or fractured, weathered rock are often encountered. Under such conditions, special problems with tunnel support, underpinning of structures adjacent to the tunneling, and/or flow of groundwater into the tunnel occur. If the ground conditions are appropriate, i.e., the soil is sandy, silty or fissured, or the rock is weathered or fractured, the solution to these tunneling problems may be chemical stabilization of the ground. Injection stabilization as an aid to tunneling is practiced extensively in Europe and its use is increasing in the U.S. The advantages of this technique over conventional solutions can be substantial in terms of cost and time, especially in mechanized tunnel boring where even a small zone of soft ground can bring the tunneling to a complete halt. In this paper European practice in using chemical ground stabilization for urban tunneling will be reviewed. In contrast to previous papers which have dealt with specific applications (1,5,8,9) this paper will broadly cover the subject, addressing itself to grouting techniques, costs, the reasons for grouting, philosophy of the users towards grouting, design of grouting solutions (or lack thereof) and methods of quality control. Differences with U.S. grouting practice are also noted. The information presented is derived from several visits to Europe, discussions with European and U.S. grouting personnel, and the available literature (2). The author's most recent European trip was made under the auspices of the U.S. Department of Transportation in conjunction with a research study being performed at Stanford University; a detailed report of this visit is available in reference (6).

Jan 1, 1976