Search Documents

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant' with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

By Morgan M. Sears

The stability of gateroad pillars is crucial in deep-cover longwall mining, especially during transitions to wider panel layouts. This study evaluates the transition from a 700-foot to a 1,000-foot panel layout with an inter-panel barrier in a deep-cover longwall mine in Southwestern Virginia to identify a configuration that enhances stability and reduces operational risks. Using the LaModel program, three pillar configurations were simulated to assess their performance based on stress distributions and pillar safety factors. These included the previously used 4-Entry Yield-Abutment-Yield layout, the current 3-Entry Yield-Abutment layout with a 220-ft inter-panel barrier, and the proposed 3-Entry Yield-Yield layout with a 320-ft inter-panel barrier. The findings of this study suggest that the proposed 3-Entry Yield-Yield pillar layout is more effective in managing stresses in deep-cover mining environments. By optimizing pillar placement and improving load management, this layout could positively impact mineworker safety and health. The study underscores the importance of advanced simulation tools in developing innovative solutions to address the challenges of modern longwall mining operations.

Feb 1, 2025

By Shingo Morimoto, Toru Sasaki, Masato Shinji

"1. INTRODUCTIONTunnel face stability is one of the most important consideration in New Austrian Tunneling Method. In general, if all of the material properties of ground can be obtained through the field investigations, the tunnel face behavior can be predicted using numerical simulation prior to tunnel construction. However, estimating the safety of a tunnel face is difficult, especially in cases where the ground is very weak such as in an urban area.In this study, numerical analyses of tunnel excavation in very weak ground conditions, such as a low cohesion and low internal friction angle, were carried out. The relationship between the average shear strain distribution on the tunnel face and the overburden was analyzed. This relationship estimates the shear strain of the tunnel face relative to the critical shear strain obtained by the ground properties. The critical shear strain was defined as an allowable value for the maximum shear strain. We proposed the allowable overburden as tunnel face stability index (TFI) that satisfies the critical shear strain criterion of ground. Finally, a design chart of the allowable overburden for various cohesion values and friction angles of ground was created. This chart is useful in the preliminary tunnel design stage to judge the necessity of additional counter measures against normal tunnel support design.2. WEAK GROUND MODELING AND ANALYSIS PROCEDURE2.1 Setting material propertiesWith reference to a past study1), the material properties were adopted on the basis of material properties in the standard worst rock classification case called “DII”2) for standard support pattern of weak ground in Japan. The typical material properties for “DII” are listed in Table 1. In addition, Fig.1 shows the distribution of the representative weak ground according to cohesion and internal friction angle. When the internal friction angle is relatively high and the cohesion is weak, the ground is categorized as sandy ground. Furthermore, when the internal friction angle is low and the cohesion is strong, the ground is categorized as clayey ground."

Jan 1, 2016

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

By J. Pancher

"Stainless steel castings are used in abundance in the mineral processing industry. In rotary kiln-based processes, these castings are typically exposed to high loads, corrosive elements, mechanical abrasion and cyclical temperature exposure. In the processing of iron ore pellets, it is typical to use a traveling grate preheater or a straight grate furnace to heat the pellets. Both machines have a conveyor that is mainly comprised of high temperature stainless steel castings. It is these castings which are the focus of this study. The expected life of these castings can be quite short, their cost quite high and the effort to replace them very labor intensive. The goal of this study was to gain a better understanding of the failure modes of these castings. With that basic understanding, modifications to the alloy content could be made to achieve a new operational paradigm. That paradigm could be a cheaper casting, a longer lasting casting or a casting tailored to special operating conditions (for example, highly corrosive gases or sudden temperature shocks). Over the past 4 years, Metso Minerals has sought to achieve a better understanding of the failure modes through modeling, laboratory testing and sampling of used castings from various end-users. In addition, we have tested new alloys in a laboratory setting and also in the field to see how they would perform compared to the existing ""standard casting"". Our testing has revealed interesting data concerning the impact toughness, sigma phase content and formation, chloride attack and other performance attributes of various grades of stainless steel when exposed to cyclical temperatures. Interesting results were also obtained concerning the addition of rare earth elements (Niobium, Boron, etc), nitrogen and manganese to a typical ASTM A297 grade of stainless steel. To date, a few hundred test castings have been installed in iron ore pellet plants worldwide. Many of these test castings have already experienced a year or more of operation with good results.INTRODUCTION Cast stainless steels (ASTM A297 and similar) are a main constituent used in the construction of iron ore pelletizing equipment. A typical straight grate pelletizing machine would contain upwards of 160,000lbs of ASTM A297 Grade HH castings. With a typical casting lasting only two to four years, and a casting costing around $35USD, it is easy to see that the castings are a main contributor to the overall cost of producing the pellets. Grade HH and HI (see chemical composition listed below) became the “go to” materials in the 1960’s and very few changes have been made to this day (the exception being plants that switched to flux pellet production in the 1980’s)."

Jan 1, 2015

By Mark C. Williams, Thomas P. Meloy

Particle shape characterization is a complex task made more difficult because of the human eye's sophisticated recognition of shapes, giving rise to the assumption that shape analysis is considered a simple problem. Further exacerbating the problem is the question of whether particles have a general shape. Old and new shape measuring techniques are discussed, particularly the new image analysis methods techniques such as Fourier, Haar, Walsh and Delta. Problems with the current image analysis equipment and future research equipment needs are presented.

Jan 1, 1989

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By D. A. Longhurst

Improper size distribution of the grinding media in a multicompartment mill can be a source of many operation problems encountered. Inefficient use of the power expended for grinding, and an undesirable product size distribution are two frequent resultants. It is necessary to resize the grinding media in the leading mill compartment at time intervals related to the abrasive nature of the material being processed. In practice, this is done when time permits and with sketchy guidelines, if any. Maintenance of the grinding media size distribution can be scheduled, and would be, with a realistic method supplied to the user.

Jan 1, 1984

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By Robert C. Maxton

The foundry industry is a basic source of structural component for all industry. Millions of tons of castings are produced annually in both ferrous and nonferrous alloys. These castings are subjected to a wide variety of heat treatments, finishing techniques, mechanical tests and machining operations. Through all of these steps the quality of the casting is of paramount importance to the end use of the product. The Quality Assurance Program at Minneapolis Electric Steel Castings Company is designed and established to provide a superior product for both original equipment manufacturers and the mining industry.

Jan 1, 1982

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 'C per 100 m (Virgin Rock Temperatures, VRT, around 50 'C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By Andrew Allan

[The Thompson Creek Coal and Coke Corporation, a. mall company engaged in producing coal in the Rocky Mountains of Colorado, is currently engaged in a struggle of destiny to increase their production from inclined seam operation to compete with highly mechanized horizontal bed mines. This paper introduces some of the problems encountered it pitch seam mining as they apply to the convention, room and pillar system employed at the present time. Further described is the test work now being conducted to overcome these obstacles with an. attendant increase in productivity. Included in this test work is a mining machine designed especially for pitching seams, an automated longwall, and hydraulic mining of the latter compared with those of conventional work presently employed.]

Jan 1, 1965

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By S. K. Kawatra, J. A. Halt

"INTRODUCTION Iron ore beneficiation needs advances in areas such as process control, automation, burner and furnace designs, silica-free binders, and even alternative iron making routes. While some – like new binders – are only step-changes, all are tools that can help make the ironmaking industry more sustainable. This paper focuses on binders. Binders are added to iron ore fines before they are agglomerated. Binders are used to control the balling process and increase the mechanical quality (e.g. strength) of green-balls and pellets. Agglomeration usually follows thickening and filtration. Good-grade ores, which don't require upgrading, are wet ground to decrease particle size and increase specific surface area. Low-grade ores are often extensively upgraded through wet operations (flotation, dispersion and selective flocculation, magnetic separation, etc.). For both types of ores, thickening and filtration conclude the circuits so that moisture contents are lowered and the ores can be agglomerated. It's been known for a long time that thickening and filtration behaviors are influenced by zeta potential (Sandvik, 1979). Highly-negative zeta potential is good for dispersion while low zeta potential is good for filtration. So, the zeta potentials of iron ore particles are lowered with additions of acid or carbon dioxide, for example, to increase filtration rates and throughputs (Eisele et al., 2005). What happens to particles as their zeta potentials are lowered? Particles aggregate together, effectively forming larger particles. How stable then, are those aggregates during mixing and balling? Are they easily broken up during mixing (if mixers are even used)? Are they broken up during balling? Or, do the aggregates resist breakage so that the availability of ultra-fines, which are so beneficial for agglomeration (Stone, 1968), is decreased? For plants where high doses of bentonite are used as binder, the above questions may be of no concern. The bentonite adds the necessary amount of fines; however, even at those plants, the calcium and magnesium contents in the water affect bentonite's effectiveness (more magnesium and calcium means less effective bentonite). (Engesser, 2003) For plants where new silica-free organic binders are being developed and used, the above questions may need to be considered. The binder is only amongst the iron ore particles for a short period of time – until it burns away or thermally decomposes in the induration furnace – so the liberation, availability and distribution of fine particulates is very critical for the quality of balls and pellets. It was hypothesized that high zeta potential conditions would lead to good pellets, while low zeta potential conditions would lead to relatively bad pellets."

Jan 1, 2018

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

2.1 INTRODUCTION When total extraction of an opening of sufficient size is reached in a horizontal coal seam, the roof strata in the overburden deform continuously to reach a new equilibrium condition. The severity of deformation decreases upward toward the surface. As the downward saggings of the strata propagate and reach the surface, there will be a depression zone on the surface directly above, but extending beyond the edges of the underground opening. This is the surface subsidence basin or surface subsidence trough. The surface subsidence basin is circular in plan view, if the coal seam is horizontal and the mined-out opening is square in shape. But it is rectangular with rounded corners or elliptical if the coal seam is horizontal and the mined-out opening is a long- and thin rectangle or a short-rectangular, respectively (Fig. 2.1). Most underground openings (e.g., longwall panel) assume rectangular shape when total extraction has been completed. Theoretically the edges of the subsidence basin are the points of zero subsidence. But it is difficult to exactly locate the points of zero subsidence. Therefore in practice the points with vertical subsidence of 0.4 in. (10 mm) are used. The final subsidence basin is that which exists long after the mining has been completed, because its magnitude and shape are quite different from the dynamic subsidence basin formed while the face is moving. 2.2 CHARACTERISTICS AND TYPES OF DEFORMATION IN THE FINAL SUBSIDENCE BASIN For a horizontal coal seam, every point in the subsidence basin moves toward the center of the basin. Subsidence is maximum at the center of the basin. Any cross-section that passes through the point of maximum subsidence and either parallel to AB or CD line (Fig. 2.1) is a major cross-section along which principal directions of surface movements occur. However among those infinite numbers of major cross-sections, two specific ones are of special significance, not only because the magnitudes of surface movements are the largest, but also because they are the most easily identifiable directions, i.e., one that is parallel to the faceline at the center of the basin (CD in Fig. 2.1) and' the other is that perpendicular to the faceline but parallel to the diction of face advance (AB in Fig. 2.1). Nearly all the subsidence data obtained in the US have been derived from these two cross-sections, although some cross- sections parallel to CD but near the edges of the panel have also been included. In addition to moving horizontally toward the center of the basin, every point in the basin also subsides vertically. The magnitude of subsidence increases toward the center of the basin. Therefore surface subsidence is a three-dimensional problem and should be treated so in all cases. On all the major cross-sections, only principal subsidence and principal displacement occur. Since subsidence and displacement vary continuously in every major cross-section, three additional deformation components are de- rived, i.e., slope, curvature, and strain. On all other non-major cross-sections on the other hand the five components are accompanied by two additional components, i.e., twisting and shear strain. The seven components of the surface movement are defined as follows (Fig. 2.2): 1. Subsidence, S. On any cross-section, the vertical component of the surface movement vector is called surface subsidence. It generally points downward. But sometimes it points upward in areas ahead of the faceline or beyond the edges of the opening. In such cases it is a surface heave which is usually less than 6 in. 2. Displacement, U. On any cross-section, the horizontal component of the surface movement vector is called surface horizontal displacement. It generally points toward the center of the subsidence basin. But in steep terrain, it moves along the downdip direction 3. Slope, i. On any cross-section, the difference in surface subsidence between the two end points of a line section divided by the horizontal distance between the two points is called the surface slope of the section. 4. Curvature, K. On any cross-section, the difference in surface slope between two adjacent line sections divided by the average length of the two line sections is called the surface curvature of those two line sections. There are two types of curvature: con- vex or positive curvature and concave or negative curvature. 5. Horizontal strain, e. On any cross-section, the difference in horizontal displacement between any two points divided by the distance between the two points is called horizontal strain. If the distance between the two points is lengthening, it is tensile strain with positive sign. Conversely, if it is shortening, it is compressive strain with negative sign 6. Twisting, T. On the surface of the subsidence basin, the difference in slope between two parallel line sections divided by the distance between the two line sections is called twisting. 7. Shear strain, y. Shear strain is the changes in internal angles of a square on the surface of the subsidence basin or on any major cross-section. It is the summation of the differences in incremental (or decremental) lengths between the two opposite sides divided by the original distance between the two opposite sides. More precisely, the surface deformation indices (i.e., slope, strain, curvature, twisting and shear) are defined by derivatives of surface movement components. For simplicity, the x- and y-axes of the cartesian coordinate system are set to be parallel and perpendicular to the cross-section of interest, respectively. In such a coordinate system, slope and curvature along x direction are the first and the second derivatives of the vertical components (S) of surface movement with respect to x, respectively, or i, = ds/dx and kx = d2s/dx2. Horizontal strain along x direction is the first derivative of the component along x direction of the horizontal displacement,

Jan 1, 1992

By Michael Markels

The United States Environmental Protection Agency (EPA) is charged under the Federal Water Pollution Control Act Amendments of 1972 with establishing effluent limitations which must be achieved by point sources of discharge into the navigable water of the United States. Section 301 (b) of the Act requires the achievement by not later than July 1, 1977, of effluent limitations for point sources, other than publicly owned treatment works, which are based on the application of the best practicable control technology currently available as defined by the Administrator pursuant to Section 304(b) of the Act. Section 301(b) also requires the achievement by not later than July 1, 1983, of effluent limitations for point sources, other than publicly owned treatment works which are based on the application of the best available technology economically achievable which will result in reasonable further progress toward the national goal of eliminating the discharge of all pollutants, as determined in accordance with regulations issued by the Administrator pursuant to Section 304(b) to the Act. Section 306 of the Act requires the achievement by new sources of a Federal standard of performance providing for the control of the discharge of pollutants which reflects the greatest degree of effluent reduction which the Administrator determines to be achievable through the application of the best available demonstrated control technology, processes, operating methods, or other alternatives, including, where practicable, a standard permitting no discharge of pollutants.

Jan 1, 1975

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By Y. Xi, T. M. Yegulalp

An availability approach for determining the capacity of a major Bucket Wheel Excavator (BWE) system to be used in the Yuabaoshan Surface Coal Mine in China is presented in this paper. Based on previous studies on other BWE systems for delay times due to internal and external causes and a four-level maintenance and repair schedule, a model was developed, taking into account all random failures, to present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity, are discussed.

Jan 1, 1994