Search Documents

By J. C. Draper

This subject was introduced last April in a paper presented in Birmingham, Alabama, by James E. Elkin, General Superintendent of Duquesne's Coal Department. This paper will cover some of the same data and in addition it will update and further describe our experience. Our Portal No. 3 was started in June 1965 with battery tractor-trailer face haulage. This mine is operating in the Sewickley seam in Dunkard Township, Greene County, in Southwestern Pennsylvania as shown on Fig. 1. The Warwick group of mines fronts on the Monongahela River and extends westward for some ten miles as shown on Fig. 2.

Jan 1, 1968

By Richard C. Neavel

Among the many compositional parameters used to judge the quality of a steam coal is the fouling factor of Attig and Duzy1 [% base in ash % acid in ash X % Na20] in ash. The higher the fouling factor, the more likely the heat transfer surfaces of the boiler will acquire a deleterious deposit of sintered ash. While examining the elemental composition of ash from various size and gravity fractions of coals from Illinois, we noticed that variations in the fouling factor were attributable mostly to variations in the sodium content. Further, sodium content was essentially the same in all sink-float fractions from a given coal. In other words, sodium was related neither to the ash nor to the organic material. We therefore concluded that the sodium was most likely in the pore water, which was approximately a constant proportion of all fractions. This led to the supposition that the sodium might be removable through water extraction. This supposition tended to confirm the observations of Daybell,2 Daybell and Gillham,3 and Gluskoter and Ruch4 that much of the sodium in coals existed as water soluble sodium ions. In passing, it should be noted that most sodium in Western U.S. coals (i.e., Wyoming, North Dakota, Montana) is not water soluble, but rather is fairly strongly held in association with the organic material (ion-exchanged).5 Because data reported in the literature were not very conclusive about the typical proportions of sodium that might be removed by water extraction, and because there were few data indicating extraction rates, and finally, because our calculations showed a favorable economic incentive to lower sodium contents, we initiated an experimental program to investigate water extraction of sodium from Illinois coals.

Jan 1, 1976

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

Over the years, numerous studies have been conducted to characterize the floatability of coal pyrite. Unfortunately, many of the results obtained using isolated samples of coal pyrite are not directly applicable to actual coal flotation systems where liberation and entrainment may be the major factors affecting pyrite rejection. In this paper, the association of pyrite with other coal constituents is investigated, and the data are presented for feed and product streams obtained from release analysis tests. Release analysis is used to minimize the effects of entrainment. Particle distributions for each stream are presented as functions of size and composition in order to discern the behavior of free and composite particles.

Jan 1, 1992

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By Michael Li, Kathryn Rogers, Arie Moerman, Mike Cooper

The Brunswick Mine, a Division of Noranda Inc., produces zinc, lead, copper, and bulk lead-zinc concentrates through underground mining of a large massive sulphide deposit. The mining method employed is longhole open stoping with delayed backfilling. In 1996 Brunswick began a review of its mining methods and backfilling operations. In 1997 the decision was made to convert the backfill system from cemented and uncemented rockfill to paste backfill prepared from mill tailings. This paper will describe the features of the backfill preparation and distribution systems, review the handling of technical issues, and discuss experiences since plant commissioning.

Jan 1, 2001

The National Mining Hall of Fame and Museum will hold its Ninth Annual Induction Banquet Sept. 8, 1996, at the Las Vegas Hilton Hotel. Six mining greats, two of them living, will be enshrined at the event. They will join 126 other mining legends previously honored by the hall of fame. The keynote speaker will be William Perry Pendley, president and chief legal officer of Mountain States Legal Foundation in Denver, CO. Jeffrey Zelms, president and chief executive officer of The Doe Run Co., will be master of ceremonies. Richard Swayne, regional director USA for Boart Longyear Co. of Salt Lake City, UT, will introduce the speakers. Thomas Falkie, president of Berwind Natural Resources Corp. and chairman of the Mining Hall of Fame’s board of governors, will enshrine the inductees.

Jan 1, 1996

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984

By S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques including galvanostatic and steady state polarization, cyclic voltammetry and impedance spectroscopy were used. The results show that the dissolution of chalcopyrite is incongruent. Initially, at low potentials(<O.34V), iron species are released which give rise to the growth of an iron-deficient sulfide (IDS) layer. The dissolved iron might reprecipitate as a hydroxide layer depending on solution composition. Continued oxidation involves diffusion of species through the product layer. At higher potentials (>O.48V) further oxidation leads to dissolution of copper and sulfur species with a resultant breakdown of the IDS layer. The changes in properties of surface coatings resulting from various electrochemical treatments are discussed.

Jan 1, 1991

By A. Bergmann

Location The Meggen Mine and the concentrator plant of the "Sachtleben Bergbau G.m.b.H." are located in the southern part of the Ruhr-district of the Federal Republic of Germany. The mine has been in operation for more than 100 years, but the concentrator described in this paper was built in 1962 and started up in January 1963. Goelogy and Mining The Meggen ore-body is of sedimentary origin and occurs in a zone of limestones, graywacke and shales of Devonion age. The average thickness of the deposit is 3 meters and, due to an intense folding of the area, the mineralized zone dips very steeply at 800 toward the north. The ore consists of 85 percent of sulfides and 15 percent gangue that mainly contains silicates from the host rocks. The principal ore minerals are pyrite (67 percent), sphalerite (16 percent) and galena (2 percent) with minor amounts of marcasite and only traces of chalcopyrite. As shown in Fig. 1, the sphalerite and galena are very finely disseminated in the massive pyrite of the Meggen ore, and a very fine grinding combined with a special flotation technique are required to liberate the valuable sulfides and to produce separate concentrates of lead, zinc and pyrite. Mining is performed by the sub-level stoping method and employs trackless equipment. Present operations provide ore from the 600 meter level. Annual ore production is 870,000 metric tons.

Jan 1, 1972

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet&apos;s producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product&apos;s quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet&apos;s porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historical Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon in leach for recovery of gold ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a course rock fraction from the grinding circuit SAG mill. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900s. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1983

By Ronald M. Hays

During the twentieth century the Mesabi Range in northeastern Minnesota has been the major source of iron ore for American steel mills. The Mesabi Range extends along an iron bearing outcrop known as the Biwabik formation. This outcrop is some 120 miles long and up to three miles wide. The formation is from 200 to 650 feet thick and dips 5 to 10 degrees to the southeast. The iron content of the original Biwabik formation was quite uniform, but much of this formation has been subjected to alteration. Thus major variations in iron content and mineral composition exist both laterally and vertically in the present Biwabik formation. The remaining unaltered iron formation includes the magnetic taconites which are commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons. per year of iron pellets and have produced approximately 170 million tons of pellets since 1956. Capacity for another 30 million tons per year of pellets is being considered by the industry for the next ten years. This increase will be obtained by construction of new plants and expansion of present operations. Thus by 1977, it is estimated that approximately 60 million tons per year of iron pellets will be produced from magnetic taconite on the Mesabi Range. The portions of the Biwabik formation subjected to intense alteration resulted in the direct shipping, wash and heavy media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron for American steel mills. In 1966, 12 million tons of direct shipping ore and 18 million tons of wash, jig, heavy media and other gravity concentrates were shipped from the Mesabi Range. These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from about 30 million tons in 1966 to 6 to 8 million tons in 1975. This decrease will be due to depletion of reserves and poor quality product.

Jan 1, 1968

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant&apos;s -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By A. L. de Vegt

For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m /d. A pilot plant started operation in November 1995 at Kennecott&apos;s Bingham Canyon Utah copper mine to develop the processes for metal and sulfate removal from groundwater and selective copper recovery from leach water. The principle of the biotechnological methods, full scale experience, and an overview of the test program at the copper mine are presented.

Jan 1, 1997

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985