Search Documents

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Roger Malmström, H. Heden, Kjell Lidin

INTRODUCTION LKAB was formed at the turn of the century when the railways between the ore fields and harbors were built. The mines are situated north of the Arctic Circle in Sweden. Kiirunavaara is the largest mine, with a pro¬duction capacity of approximately 30 Mt/a. Malm¬berget has a capacity of about 12 Mt/ a. Both are under¬ground mines. Svappavaara, the only opencast mine currently in operation, has a capacity of about 4.5 Mt/a. The ore harbors are at Narvik for the Kiruna and Svappavaara mines and at Lulea for the Malmberget mine (see Fig. 1). Production in the form of finished products is shown in Fig. 2a, b, c, and d. Due to poor ore markets in re¬cent years, production and shipments have been cut back, but there was a positive swing in 1978. LKAB has been 96% state-owned since 1957. In addition to the iron mines in northern Sweden, LKAB has subsidiaries in central Sweden which produce sulfide ores, quartz sand, and uranium (Fig. 3). The mining methods employed are opencast bench stoping at Svappavaara and sublevel caving at Kiirunavaara and Malmberget. GEOLOGY The Kiirunavaara ore body is 4000 m long and av¬erages about 90 m wide, with variations in width from a few meters to around 150 m. The ore has been ex¬plored by deep drilling down to about 1000 m, but mag¬netic measurements indicate a depth of at least 1500 m. The Kiirunavaara ore is oriented in a north-northeasterly direction with a number of ores in the boundaries be¬tween the wall rock types. The ore in Kiirunavaara is mainly a fine-grained magnetite with a varying content of fine-grained apatite. The apatite content of the ore decreases with increasing depth. The other ores are all apatite-bearing and a couple are hematite ores (Fig. 4a, b). The ores are sedimentary, tilted, and tectonically de¬formed. They have a lateral dip of 0.87 to 1.2 rad (50 to 70°). The contacts between ore and wall rock are distinct and sharp, but both the hanging wall and the footwall are brecciated and impregnated with magnetite. The footwall of the Kiirunavaara ore consists of syenite porphyry with a low quartz content and rela¬tively good strength; the hanging wall consists of quartz porphyry. Both types are known as Kiruna porphyries. The ore at the boundary with the hanging wall is often rich in kaolin. There are a few veins of syenite porphyry running through the ore, which has a few major faults (Fig. 4c, d). There are two sharply delineated ore grades in Kiirunavaara: low phosphorus ore with less than 0.1 % phosphorus (about one-third of the ore) and high phos¬phorus ore with greater than 0.5% phosphorus. The iron content is 67% in the low phosphorus ore and 60% in the high phosphorus ore. These ore types are sold as different grades and so are kept separate during mining. MINING AT KIIRUNAVAARA The Kiirunavaara and Luossavaara ores were first mined using opencast bench stoping in 1902. When mining costs rose owing to higher waste removal, under¬ground methods were adopted. In the mid-1950s, the ores were still being mined on the surface at the same

Jan 1, 1982

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By S. L. Barua

An industrial engineering and computer simulation study was conducted on reclamation operations to evaluate the possibility of integrating mining and reclamation operations, and to evaluate the factors which influence the production potential of scrapers. The study was done in a southern Illinois strip coal mine producing approximately 2.27 M metric tons (2.5 million short tons) of clean coal annually. The main outcomes of this study are (a) it is possible to reduce reclamation cost about 20-25 percent by integrating reclamation and mining operations, (b) haul distance has the most significant effect on scraper production, (c) push-pull is the best mode of operation for wheel scrapers for topsoil/subsoil removal, and (d) historical data obtained from the mine for one year show that average dozer productivity in rock grading is about 60 percent lower than the expected production; similar data for scraper is about 25 percent less.

Jan 1, 1981

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By Rex C. Bryan

An accurate and dependable ore reserve estimate is important to any mining company. It is also essential for development drilling and production planning to know about the distribution of the ore within the area to be mined. This paper will show that in the case of more variable deposits such as uranium, the use of geostatistics is superior to conventional techniques. Unlike conventional methods, geostatistics includes the importance of spatial orientation of measured variables. With the use of variograms in conjunction with kriging, a point or a block may be estimated along with its error of estimation. The existence of disequilibrium can create a severe problem in uranium 'ore reserve estimation, and mine and production planning. Disequilibrium can be simply defined as the ratio of chemical or assay values to gamma equivalent values calculated from the downhole geophysical gamma-ray logs. Various methods for adjusting for disequilibrium have been proposed. Most, however, have side stepped the consideration of disequilibrium itself being a regionalized phenomena; or its, relation to surrounding geology. This paper presents methods of incorporating both aspects. The East Dilts Pit at the Bear Creek Uranium Mine in Wyoming, has been used as a case study. Polygonal, triangular, and lognormal kriging and various disequilibrium adjusted methods, including multi-factor cokriging have been com- pared with the mining experience.

Jan 1, 1982

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019

By I. WILKOMIRSKY, J. BECKER, F. Parada

The current processes that aim to purify molybdenite concentrates are not able to dissolve some copper compounds, hence limiting the processes. Typically, the copper content results are from 2 up to 4 weight percent in the last concentrate. Such values are still too high for the molybdenite concentrate to be further processed to molybdenum trioxide by roasting. In order to achieve lower levels of copper — but also avoid excessive molybdenite losses — a continuous sulfation-leaching process is investigated and applied successfully on a pilot scale. Additionally, a reactor prototype and its process parameters are proposed for a commercial plant.

Jan 1, 2023

By James R. Hindman

Vermiculite is the mineralogical name generally applied to a group of hydrated, trioctahedral ferromagnesian aluminum platty or micaceous silicate minerals. In microscopic particles the mineral as mineral is differentiated from montmorillonite by a higher Si:AI ratio of approximately 3:l and a higher layer charge and higher cation exchange capacities. Commercial vermiculite, the vermiculite which is mined, beneficiated, and discussed in this chapter, is an important industrial mineral which is formed by the alteration of macroscopic particles of biotite and iron-bearing phlogopite. In natural form it has the size and shape of mica, while possessing the ion exchangeable properties of zeolites and some clays. Within the internal structure of vermiculite lie water molecules, which when rapidly heated to high temperature, transform into steam causing the vermiculite particles to increase in volume. This process of thermal exfoliation produces a lightweight product which finds use in various construction products, agriculture, horticulture, and other industrial applications. In exfoliated form it has the low density and biological inertness of expanded perlite, while maintaining a chemically active surface. Most of the uses of vermiculite are for the thermally exfoliated material. In addition, the cation exchange potential of vermiculite and its layer-silicate structure are properties which can be used as the basis for numerous products including intumescent coatings and gaskets, inorganic films, and the treatment of nuclear and other toxic waste. When chemically and physically modified, it possesses some properties common to organoclays and synthetic compounds. In high purity concentrates and manufactured products, these properties can be altered and optimized in applications to produce superior performance. GEOLOGY Mineralogy Vermiculite was first described as a mineral by Thomas H. Webb in 1824. Webb believed vermiculite to be a variety of talc and described its diagnostic property of thermal exfoliation thusly: "If subjected to the flame of a blowpipe, or that of a common lamp, it expands and shoots out into a variety of fanciful forms, resembling most generally small worms having the vermicular motion exact." Observing that with one exception, all commercial vermiculite has formed by the alteration of iron-bearing phlogopite, a simple definition of vermiculite might be the alteration product of trioctahedral micas, macroscopic particles of which display marked exfoliation when heated rapidly to temperatures above 374°C (the critical temperature of water). The first vermiculite described was found near Worcester, MA, but it was later pointed out by Brush (1866) that vermiculite had been known for some time in Japan as a children's novelty. Because the techniques for mineral analysis were somewhat primitive com- pared to those routinely available today, and because the structure and crystal chemistry of the micas and related minerals were not widely understood, the early literature generated at least 20 "new" minerals which were nothing more than variations in the color and chemistry displayed by vermiculite. Trade names such as Dugarlite, Mandolitem, Strong-LiteTM, and Zonolitem are sometimes used to denote commercial vermiculite, thermally exfoliated vermiculite and their products. Vermiculite particles resemble mica and vary in color from colorless through tan and green to black, depending on the chemical composition. Most physical and optical properties are close to those of biotite, with perfect basal cleavage, hardness between 1.5 and 2.5 Mohs, and specific gravity between 2.2 to 2.8. Fine-sized particles will feel talcose, especially when wet. However, for commercial vermiculite the diagnostic test is that of thermal exfoliation. Vermiculite can display a wide range of compositions, depending on the composition of the original mica and the change of chemistry during weathering and ion exchange. Chemical data for some commercial vermiculites are given in [Table 1]. There are numerous analyses for vermiculite given in the literature, and the analyses of vermiculites from commercial deposits will fall within the range indicated by the average analysis in the table. Many analyses separate the adsorbed water (H2OP) from crystalline water and water as hydroxyl (H20+). The basis of separation of adsorbed water is generally considered to be 100°C. However, hydrate water within the vermiculite interlayer begins to be lost at 75°C and lower. Therefore, measured water content and loss on ignition are combined in the table as H20[total].

Jan 1, 1994

By Brett P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using alkali solutions1. Without implementing emission controls, world energy emissions will rise from 29.7 billion t in 2007 to 42.4 billion t in 2035. The first objective of the project was to determine the optimal amount of alkali in solution for CO2 absorption. This was accomplished using theoretical equilibrium calculations and experimental absorption data for alkali solutions of 1, 2, 3, 4 and 5 weight %. As the % alkali in solution increased, so, too, did the ionic strength of the solution. Theoretical calculations took into account the effect increasing ionic strength will have on the solubility of gaseous CO2. The calculations assumed negligible formation of H2CO3, constant temperature and constant pressure. In the experimental setup, a 16% CO2 /balance air gas mixture was bubbled through an Erlenmeyer flask filled with an alkali solution. The gas exiting the flask was fed to a gas analyzer to record the % CO2 in the exhaust gas stream. The % CO2 absorbed was taken as the % CO2 in the exhaust gas minus the % CO2 in the feed. Theoretical calculations found that as the % alkali in solution increases, the solubility of CO2 decreases. This was verified by experimental data, which found that a 2% alkali solution, by weight, was the ideal solution for CO2 absorption. Current research is focused on using the 2% alkali solution for permanent storage of CO2 via mineral carbonation to produce a value-added product.

May 1, 2012

By M. Polat

A combined heavy medium-flotation process which incorporates the advantages of two widely employed cleaning methods, namely, heavy medium separation and flotation was used to achieve improved separation of coal from ash at fine sizes and to recover the heavy medium as a substantially recyclable product. The investigation was carried out in two successive phases. In the first phase, tests were performed to deter-mine the effect of different variables such as the medium density, flotation time, magnetite type, etc. on the efficiency of the process using in-plant samples from Homer City Coal Preparation Plant. In the second phase, the optimum conditions determined in the first phase were employed to determine the applicability of the process to a few Central Pennsylvania coals. It was observed that the process was very effective in recovering the magnetite. In most of the cases investigated, the magnetite was separated from the non-magnetic material at approximate-1 to 99 % recovery with a grade ranging from 95 to 99 %. The grade of magnetite decreased with increase in ash content of coal and with decrease in size of magnetite.

Jan 1, 1992

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984

By J. W. Wilson

In the ultrafine coal cleaning process, small coal particles (-400 mesh) are produced during the pulverizing operation. After the coal cleaning process, these ultrafine particles are very difficult to dewater, and create problems in coal transportation, storage and handling at utility plants. Research work on ultrafine coal dewatering and briquetting has resulted in the development of a single stage operation that is potentially more effective and economic than conventional thermal drying and briquetting processes. The final coal product have a moisture content of less than 15% and possess high strength and water resistance that satisfies coal transportation, storage and handling requirements.

Jan 1, 1995

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By Roger L. Hulette

Mt. Newman Mining Co. is now completing an expansion program, begun even before initial construction was complete, which will result in facilities with the ability to ship over 30 million tons of iron ore per year by early 1973. Confidence in such rapid future growth was evidenced by careful planning for the future expansion of those facilities provided for initial operation of the project which first shipped ore on 1 April 1969. Ore sales contracts totaling more than 300 million tons have been negotiated, thus justifying the optimism which led the joint venturers to provide over $200 million in initial investment and a like amount in capital required to finance the continuing expansion program. Members of the Mt. Newman Joint Venture are: Amax Iron Ore Corporation - 25% (a subsidiary of American Metals Climax) Pilbara Iron Ltd. - 30% (a subsidiary of Colonial Sugar Refining) Dampier Mining Ltd. - 30% (a subsidiary of Broken Hill Proprietary) Seltrust Iron Ore Ltd. - 5% (a subsidiary of Selection Trust Ltd. of London) ? Mitsui C. Itoh Iron Ore Pty. Ltd. - 10% Mt. Newman Mining Co. Pty. Ltd. manages the project on behalf of the five companies which make up the joint venture.

Jan 1, 1972

By E. A. Lauha

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike sub-district of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike sub-district, there are seven major deposits: Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the sub-district are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Barrick Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post and Deep Star occur both on Barrick and Newmont property.

Jan 1, 1993

By R. M. Tyson

Sulfides present in the troctolitic and footwall rocks are placed into one of three major zones (hornfels, cloud, and basal) on the basis of their stratigraphic position and mineralogy. Hornfels sulfides, enriched in Fe, represent remobilized sedimentary sulfide. Sulfides from the Cloud Zone are probably magmatic and are enriched in PGE, Cu, Ni, and Ag. The basal sulfides, composing most of the ore, resulted from contamination of the magma by remobilized sedimentary sulfide. The basal sulfides exhibit a differentiation trend in their mineralogy and chemistry. PGE, Cu, and Ag are enriched with increasing differentiation which is attributed to fractionation within an immiscible sulfide liquid.

Jan 1, 1986

By K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized long wall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3DTM seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis. This paper focuses on the application of RockVision3DTM technology for delineating hazards caused by stress and geologic anomalies. Case studies for two bump-prone coal mines will be discussed. For example, (1) in a German deep (>1,130 m) mine, the drilling-yield method was used to verify the effectiveness of this technology in detecting stress anomalies ahead of longwalling; (2) in a Polish mine (-500 m deep), two longwall panels 4 km apart were monitored to assess structural and stress-related factors contributing to differences in mining conditions and magnitude of structural failures.

Jan 1, 1999

By E. A. Devuyst

Metallurgical processes involving the use of cyanide such as gold cyanidation, metal plating and flotation, generate effluents containing cyanide and cyanide in complex combinations with heavy metals in quantities exceeding those regarded as being safe for discharge into streams. A new process for destruction of free and complexed cyanide and related-species in wastewaters has been developed at the Inco research laboratories using sulfur dioxide, air and lime. High reaction rates are obtained in the presence of a small amount of copper which acts as a catalyst. Cyanide species can be reduced to as low as 0.1 mg/L in a very short treatment time. Examples of treatment of gold mill effluents and barren slurries, plating rinse waters and flotation liquors or tailing slurries are given.

Jan 1, 1982

By R. J. Sawyer

The Greens Creek underground polymetallic mine restarted production in 1996 from a newly discovered high grade ore zone. Efforts to improve payable gold recovery have focused on gravity separation. The paper compares testwork and plant results for a newly installed gravity circuit.

Jan 1, 1997