Search Documents

By Dominc C. Torre

INTRODUCTION Rapidly increasing capacities of equipment used to load and handle material at the face require improved haulage equipment and better methods of transporting the mined materials or "muck" to the shaft or slope and out of the mine to the processing plant on the surface. Increasingly, those transportation demands are being satisfied with underground belt conveyors. Such con¬veyors provide the most readily available, most efficient, and most reliable method of carrying materials in a continuous and rapid flow from the face loading equip¬ment to the surface plant. Almost universally, belt con¬veyors are used in coal mines and those nonmetallic and metallic mines operating in relatively flat bedded deposits. Belt conveyors are available in a wide range of capacities, mainly limited by belt width, belt speed, and weight of the material to be transported. They can be used on the level, on grades, on the surface, or under¬ground. They provide a rapid and constant flow of material, transporting the material as quickly as it is mined. Length of belt conveyors is almost unlimited. Where the haulage distance exceeds the practical capacity of a single conveyor unit, two or more conveyors can be used in series. Single conveyors more than 1.6 km (1.0 mile) long are common; multiple-unit conveyors in series operation are transporting materials over distances exceeding 16.1 km (10 miles). Depending upon mate¬rials being transported, job conditions, cost of the terrain being spanned, and alternative haulage methods avail¬able, conveyors can be conceivably economical for even greater distances. Table 1 lists maximum belt speeds recommended for most materials, relating belt speeds to belt widths. Table 2 lists capacities of typical conveyors of various widths and speeds, transporting commonly mined mate¬rials of various weights. ADVANTAGES OF CONVEYOR SYSTEMS For several years after their initial introduction, belt conveyors were available only with rigid side frames or a supporting structure of steel and concrete. That con¬struction limited underground applications, due to the cost and relative inconvenience of extending or retract¬ing the belt conveyor in the confined underground environment. However, during the last 20 years, wire-¬rope side-frame belt conveyors, as shown in Fig. 1, have become widely used in underground applications. Even wider use can be anticipated with their application to the fast movement of materials in surface mining operations. Advantages of the wire-rope side-frame belt con¬veyors were realized first in panel or section belt haulage in coal mines. Soon afterward, use of those conveyors was extended to gathering and main-line haulage. The mobility of the wire-rope side-frame conveyor is the principal reason for its success. The conveyor can be extended, retracted, dismantled, moved, and reassembled easily, even in relatively confined under¬ground spaces. The intermediate structure consists of rope support stands, wire-rope side frames, wire-rope tie-off stands, and the necessary carrying idlers and return idlers. An important and very attractive feature is the ability to suspend the conveyor from the roof in an underground mine, as shown in Fig. 2, leaving more room for improved housekeeping and allowing passage of face-service equipment, haulage vehicles, and other mining equipment. The conveyor's open construction allows quick and easy visual inspection of its com¬ponents for failures or malfunctions; it also facilitates checking and correcting conveyor-belt alignment. Other advantages contributing to the attractiveness and widespread application of wire-rope side-frame conveyors in main-line, slope, and surface installations include: lower capital costs, lower installation costs, lower maintenance costs, reduced impact on idlers and belting, reduced spillage and minimal cleanup, improved conformation to undulating terrain or mine bottoms, and the ability to span most obstacles without heavy structural support. CONVEYOR CLASSIFICATIONS Underground belt conveyors are classified normally according to their function. Generally, conveyors are classified into one of four main categories: 1) Panel or section conveyors normally receive the material to be transported directly from the face-haulage equipment. 2) Gathering conveyors are secondary haulage units that usually receive material from two or more panel conveyors. 3) Main-line conveyors transport all the material mined in the underground operations to the slope or shaft. Normally, they receive the material from two or more gathering conveyors. 4) Slope conveyors generally operate in tandem with the main-line conveyor, providing continuous Table 1. Maximum Belt Speeds Recommended for General Use Run-of-Mine Hard Ores and Belt Width, Coal and Earth, Primary Crushed mm (in.) m/s (fpm) Stone, m/s (fpm) 356(14) 1.52 (300) 1.52 (300) 406(16) 1.52 (300) 1.52 (300) 457(18) 2.03 (400) 1.78 (350) 508(20) 2.03 (400) 1.78 (350) 610(24) 2.54 (500) 2.29 (450) 660(26) 2.54 (500) 2.29 (450) 762(30) 3.05 (600) 2.79 (550) 914(36) 3.30 (650) 3.05 (600) 1067 (42) 3.56 (700) 3.05 (600) 1219 (48) 3.56 (700) 3.30 (650) 1372 (54) 3.56 (700) 3.30 (650) 1524 (60) 3.56 (700) 3.30 (650) 1676 (66) 4.06 (800) 3.81 (750) 1829 (72) 4.06 (800) 3.

Jan 1, 1982

By A. C. Bigley

Before going into this subject, I would very much like to call to your attention some past history on patents granted by the United States Patent office that involved ammonium nitrate. On February 10, 1885, a patent was granted to Russell S. Penniman. "The object of this invention is to securely protect ammonium nitrate against deliquescent and to maintain it in substantially its normal disintegrated condition, so as to afford a new product suited for ready use in the manufacture of high explosives, and enable the immediate admixture thereof with any of the well known explosive substances or compounds heretofore employed. 'Whether the nitrate be thus granulated or otherwise reduced to a granular or divided condition, it is then thoroughly mixed with about twelve (12) percent of the fluid or semi-fluid carbonaceous protecting medium, which forms a readily applied jacket or coating for the granules of nitrate and also serves as a carbonaceous element in such explosive compounds as it may thereafter be employed in."

Jan 1, 1958

By Allegra Yeley, Ted Klemetti, Gamal Rashed, Tim Miller, Nicole Evanek

In 2015, the Subtropolis Mine in Petersburg, OH, experienced a massive ground collapse that continues to grow over time. Horizontal stress effects have affected the roof at this operation in the past and may have played a large role in this collapse. Horizontal stress can impact the roof and floor stability and endanger the health and safety of underground stone miners. Mines experiencing damaging effects from horizontal stress typically find that the principal stress direction is the same throughout the mine and the region. At the Subtropolis Mine the principal horizontal stress direction appears to change as conditions change and differs from the regional horizontal stress, particularly near the collapse or other roof fall areas. The growth over time of this collapse and other roof falls have been captured and analyzed using geologic mapping, 3D LiDAR scanning, numerical modeling and geographic information systems like ArcGIS. Utilizing these tools to better understand sitespecific conditions can be critical to reducing the potential of massive ground collapses in the underground limestone industry.

Feb 1, 2024

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world's largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960's, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By J. W. Cooksley

Pyrometasomatic zones are a type of replacement deposit, normally in a carbonate rock unit, which consists of a zoned, coarse-grained, generally iron-rich mixture of calcium and magnesium silicates. These zones or rock masses are also called ?skarn,? and ?tactite?. They are formed as a result of the interaction of a shallow intrusion of magma with a carbonate or calcareous host rock and are considered to be of hydrothermal origin. Three environments of pyrometasomatic deposits are depicted in Figure 1. Of course, the interaction takes place at high temperatures. Pyrometasomatic zones are categorized as calcic or magnesian, depending on whether the intrusive interacts with a limestone or a dolomite. Common pyrometasomatic zone minerals are garnet, epidote, quartz, calcite, wollastonite, actinolite, hedenbergite and diopside. Pyrometasomatic zones are of considerable economic importance because they contain ore deposits of tungsten, molybdenum, copper, lead, zinc and iron. According to Rose and Burt (1979), the chronological sequence in the formation of a ?typical? pyrometasomatic deposit is as follows: 1. Shallow intrusion of magma at 900-700°C into carbonate sediments.

Jan 1, 1981

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994

By D. C. McDonald, P. R. Whincup, H. Duke

Due to grade, overburden depth and stability and the presence of groundwater it was considered impractical to recover gold contained in unconsolidated palaeochannel sediments by conventional mining, dredging or borehole mining techniques. A series of field experiments was conducted to determine the feasibility of recovery of gold by in situ leaching from sediments located at a depth of about 80 metres. The test wellfield site and plant are described together with field test procedures, results and wellfield rehabilitation procedures. Choice of sodium cyanide as leachant and laboratory testing are discussed in relation to groundwater and sediment chemistry and problems encountered in field tests.

Jan 1, 1989

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By N. S. Tanious

The Nuclear Regulatory Commission (NRC) regulation 10 CFR 60 requires that the ventilation system for the geologic repository be designed to: (1) control the transport of radioactive particulates and gases, (2) assure continued function during normal operations and under accident conditions, and (3) separate the ventilation of excavation and emplacement areas. The ventilation system design should take into account thermal loading; maintenance of the retrieval option and-the separation of the development and emplacement ventilation circuits. An analysis was performed by NRC's contractor, Engineers International on the ventilation system design described in the Department of Energy's conceptual design for Nevada. The ventilation analysis is of a preliminary nature. The conclusions presented in this paper reflect the views of the authors and may not represent the views of the NRC. In this analysis, available Nevada Nuclear Waste Storage Investigation (NNWSI) ventilation design information was reviewed and a ventilation network analysis was performed.

Jan 1, 1988

By George J. Skoronski

The economics of pellet plant operation, in terms of fuel and power consumption, flexibility in the selection of the cheapest fuel source, system availability, maintenance costs, and the simplicity of process design, contribute to the determination of building and profitably operating a pellet plant. Design innovations, sup- ported by actual field data, have been initiated into the GRATE-KILN System design to positively address these factors. This paper presents the recent state of the art design concepts which have helped the GRATE- KILN System assume worldwide acceptance status.

Jan 1, 1983

By T. E. Bernard

"Refuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet the U.S. Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and management of heat from the occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements and carbon dioxide generation that are representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current U.S. coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in.) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in a refuge alternative. The highest likely metabolic heat generation ranged from 113 to 134 W, depending on occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 L (0.81 cu ft) of oxygen per hour per person and 20 L (0.71 cu ft) of carbon dioxide per hour per person, which means the margin of safety is 50 percent or more compared with the MSHA requirements. The information on metabolic heat generation can be used to assess refuge alternative thermal environments by testing or simulation. The required oxygen supply and carbon dioxide removal can be used to assess refuge alternative requirements. IntroductionRefuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet U.S. Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen (O2), removal of carbon dioxide (CO2) and management of heat resulting from the refuge alternatives’ occupants and mechanical/ chemical systems (MSHA, 2008)."

Jan 8, 2018

By O. J. C. Runnalls

Canada has played a significant role in the international uranium industry for some three decades. Although there have been many challenges in the past, the future offers a more extensive range of problems and prospects as Canada moves to expand its activities in all aspects of the nuclear fuel cycle. World uranium demand could grow to an annual requirement of 500,000 tons U308 by the year 2000. A substantial fraction of this material is likely to come from Canada because the country's reserves and resources are large, and because of a favourable geological potential for future discoveries. There has been a long history of association between the producing industry and the federal government, and it has provided the foundation for existing national uranium policies. Close industry-government association will be maintained and developed in future because of the anticipated rapid growth of the industry and the consequent need for continual refinement of government policies relating to exploration, mining, processing and export of uranium.

Jan 1, 1975

By Fumio Wada

Kuroko deposit is a stratabound massive sulphide and sulphate deposit associated with Miocene submarine volcanics and has been considered to be a prototype of meta- morphosed Palaeozoic and Precambrian equivalents. Since the discovery of Uchinotai deposit of the Kosaka mine in 1959, Dowa and other mining companies have conducted intensive exploration work in the Hokuroku district of northeastern Japan. Dowa has been placing its first priority on the exploration of Kuroko deposits and made a series of remarkable successes in finding the Kuroko deposits, i.e. Uchinotai, 1959; Matsumine, 1963; Uwamiki, 1966; Fukazawa, 1969 and Ezuri, 1975. It is emphasized that our successes have resulted from the proper application of exploration technologies accumulated through our experiences. Firstly we defined the Kuroko horizon and favourable felsic volcanism based on the detailed structural and volczno-stratigraphic study of the Hokuroku district, and then delineated the promising areas by means of the quantitative evaluation of geophysical, geochemical and mineralogical parameters such as the magnetic susceptibility and contents of alkaline and alkaline earth metals in the foot wall dacites and clay mineral assemblages of both hanging and foot wall pyroclastics and dacites. Practical application of these techniques is essential to our routine Kuroko exploration.

Jan 1, 1982

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the United States for the detection of fire in the belt entry and the monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data have the potential to provide fire characteristic information such as fire growth — in terms of heat release rate — and exact fire location. Such information is critical in making decisions regarding firefighting strategies, underground personnel evacuation and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide concentration, carbon dioxide concentration and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division’s Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy.IntroductionFires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases.The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke and toxic gases are produced and transported by the ventilation system and which provides an indication of the time available for escape or firefighting (Babrauskas and Peacock, 1992). The HRR is also an important input parameter to mine fire simulation models."

Jan 6, 2017

By G. H. Lewis

This work was completed in a 440 KW pilot-scale combustor in preparation for a 50,000 Kg/hr industrial steam boiler limestone injection test program. The main objectives of the work were to: (1) identify the variables which affect sulfur capture, (2) determine the maximum sulfur removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. The variables which were identified as being important in sulfur capture were: Ca/S molar ratio, flue gas temperature at the limestone injection location, and limestone particle residence time. The maximum sulfur dioxide removal was 72%. The addition of limestone increased the particle deposition rate in the combustor; however, all deposits were easily removed by an air lance.

Jan 1, 1985

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By L. Yuan, A. C. Smith

MFIRE, the mine-fire simulation program of the U.S. National Institute for Occupational Safety and Health (NIOSH), is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines. MFIRE has been used by U.S. and international companies to simulate fires for planning and response purposes. It is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence, such as changes in ventilation parameters; external influences, such as changes in temperature; and internal influences, such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the former U.S. Bureau of Mines in the 1970s, several updates have been released. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated Fortran programming language was replaced with an object-oriented C++ language and packaged into a dynamic-link library. However, the MFIRE 3.0 release included no change or improvement to the fire-modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire-modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of the t-squared fire as a new fire-source model and the ability to include available heat-release-rate versus time data, the addition of a moving fire source for conveyor-belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke-rollback phenomena. All of the improvements discussed in this paper will be included in MFIRE 3.1 and released by NIOSH in the near future.

Jun 1, 2016

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

Roadheaders are commonly used in coal mines for roadway excavations. The prediction of roadheader performance is necessary for the planning of roadway projects and the estimation of costs. Recently, a new rock mass cuttability classification (RMCC) system has been introduced for roadheaders used in coal mines. In this study, the validity of the RMCC system was investigated for different types of roadheaders and different coal mines. Four different coal mines were visited, and the performance measurements of different axial and transverse roadheaders were carried out during the excavation of roadways. Uniaxial compressive strength, volumetric joint count, the strike and dip of joints, joint aperture, the Cerchar abrasivity index, and water ingress were determined in field and laboratory studies to calculate the RMCC index. The analysis of the data demonstrated that the correlation coefficients between the net cutting rates and the RMCC indices were higher than 0.94, suggesting that the RMCC system was valid. It was concluded that the RMCC system could be reliably used for the evaluation of roadheader performance in coal mines.

Jun 21, 2023

Exploration of new resources and development of new equipment and designs are an ever changing facet of mining. New equipment to handle specialized operations is being developed and new techniques for its use explored. One such system is reviewed. Another is a potential system for handling the thinner stray coal seams between the more profitable thick seams. The availability of federal coal leases in the West is reviewed and current planning discussed. Gulf Coast lignites have been of much interest in recent months and are overviewed.

Jan 1, 1979