Search Documents

By Arash Nikvar‑Hassani, Timothy Batchler, Lianyang Zhang

Recently, a new hybrid geopolymer/biopolymer (GP/BP) cementitious material was developed for improving the performance of pumpable roof supports in underground mines. This study demonstrates the application of the hybrid GP/BP cementitious material and validates its effectiveness in full-scale. In this regard, eight (8) full-size (0.61 m diameter and 1.52 m height) cribs were produced in collaboration with Minova International Ltd and tested at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) Laboratory. These full-size cribs were produced with different material configurations to evaluate the effect of water to solid (W/S) ratio, Portland cement (PC) content, and BP dosage. The results demonstrated and validated the effectiveness of the hybrid GP/BP cementitious material in increasing the peak and residual bearing capacities of pumpable cribs and eliminating the issue of deterioration when exposed to air compared with the conventional Portland cement/fly ash (PC/FA) cementitious material currently used in practice. On average, the peak uniaxial compressive strength (UCS) and the highest residual UCS after peak of the full-size cribs produced from the hybrid GP/BP cementitious material are 1.90 and 1.33 times of those of the PC/FA-based full-size cribs by one company and 2.32 and 1.66 times of those of the PC/FA based full-size cribs by the other company, respectively.

Feb 6, 2024

By Carrie Smith

In 1972, in Denver, CO, five women with a shared goal joined forces to create the first formal space for women in the mining industry: Women in Mining USA (WIM USA). When the organization first took shape, few could have predicted that a small gathering of women would grow into one of the most influential organizations that would advocate for inclusion in the industry. Now, more than 50 years later, the group remains a vital network for professionals across the United States with a diverse array of membership and chapters.

Jan 1, 2026

By S. Behl, S. Mathur

The viability of physico-chemical purification methods such as selective, flocculation for the separation of two components having similar chemical compositions and the same crystal structure but different surface properties is demonstrated. A loss of selectivity was observed in a dolomite-dolomite mixture when polyethylene oxide (PEO) (five million molecular weight) was used us the flocculant. Heteroflocculation was minimized using a low molecular weight PEO (MW =105) as a site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at the 100% recovery level

Jan 1, 1996

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer's machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023

By William D. Mayercheck

Beginning in 1974, the Bureau of Mines, U.S. Department of the Interior, sponsored R & D efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The U.S. Department of Energy continued this effort as of October 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems or components now being built, surface tested, or tried underground.

Jan 1, 1981

By Yi Luo

In a shearer longwall mining operation, the longwall bits are responsible for breaking into and chip-ping the broken coal blocks away from the coal face. However, underground observations have found that a large number of longwall bits are always working under various degrees of wear. Reduction of the bit wear could be realized by using better designed longwall bits and properly selected shearer operating parameters. A computer program has been developed to simulate the performance of the longwall bits. The shape of the bit head, the installation of the bits on the drum and the operation parameters are the information required by the program. Through the simulations, the main factors affecting the bit wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1996

By Xin Zhou, Huilin Jia, Xiaofei Liu, Jinxin Wang, Zifeng Meng, Zinan Du, Hui Xie, Guihang Jiang

The change of gas emission or concentration level at the working face is one of the main precursor characteristics of coal and gas outburst. At present, coal and gas outburst monitoring and early warning are mainly based on whether it exceeds the limit and its change law. However, the gas concentration level is affected by factors such as coal seam gas content, permeability, and mining process, and the change law is complex to recognize manually. In this paper, the response characteristics of gas concentration level in the mining process are analyzed and revealed, and a bidirectional long short-term memory model is established. The change characteristics of the gas concentration level in the mining and non-mining processes are studied and recognized. The results show that the change law of gas concentration in the mining process has apparent periodicity and trapezoidal volatility. The proposed intelligent recognition method based on the bidirectional long short-term memory neural network can automatically recognize the underground mining and non-mining processes, and the recognition accuracy achieves 97.7% . The research can significantly help improve the level of coal mine safety management and the accuracy of early warning of coal and gas outburst.

Apr 29, 2023

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By K. Mohamed, G. Rashed

A conventional mechanical anchor bolt consists of a smooth bar threaded at the anchor end, with a conical wedge, and a mechanical shell anchor. When the smooth bar is torqued, the conical wedge pushes the shell anchor against the borehole wall. Coal mines use mechanical bolts in addition to other types of bolts to control the deformation and stabilize the yielded coal ribs. Limited research has been conducted to understand how a mechanical anchor performs in a coal rib. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted the study described in this paper to define the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of a mechanical rib bolt. Based on the strength of the coal seam and the conditions of the coal mines, the bolts were installed at different amounts of torque. A typical tri-linear load-deformation response was obtained from these tests. It was found that the anchorage capacity depends on the coal strength, and the anchorage stiffness depends on the installation torque. The outcome of this research provides essential data for rib support design. INTRODUCTION Rib falls are a serious hazard in underground coal mines. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Although resin bolts has been used increasingly in the last few years to control coal ribs, mechanical bolting (mainly expansion-shell bolts) is still used in many underground coal mines. Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 79% of the mines determine their rib support requirement based on the depth, mining height, and the loading conditions, of which 35% use the conventional mechanical bolts. Conventional mechanical bolts are preferable for rib support because they do not require the miners to be too close to the rib during rib bolting. Hence, using the conventional mechanical rib bolts can reduce the risk of injuries and fatalities during the installation process. The mechanical bolt or the point-anchored bolt is the oldest type of rock bolt that is still in use today. The point-anchored bolt is a tensioned bolt anchored down the hole with a mechanical expansion shell or a grouted medium (Peng and Tang, 1984). Figure 1 shows the components of the mechanical anchor bolt. The mechanical anchor bolt consists of a plug, a shell anchor, a headed smooth bar with the top end threaded, a bearing plate, a hardened washer, and sometimes a friction-reducing washer. The shell anchor can be either standard or bail type. The shell of the standard type is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the smooth bar is generally 5/8 in for the #5 bolt or 6/8 in for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the wedge down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall.

Jan 1, 2019

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

Placing a detonating explosive inside a volume of rock is an efficient method of rock fragmentation. The explosion generates internal tensile stresses in the rock, and because rock is a brittle material, this brings about crack propagation and fragmentation far more efficiently than does application of explosive on the surface. To get the explosive inside, we drill a pattern of boreholes and charge the explosive into the holes. This is really the one and only purpose of making blastholes in mining: to give access for the explosive to the interior of the rock. No matter how big and expensive a drilling jumbo we stand up in front of a rock face, and no matter how many boreholes we let it drill, the rock does not fall apart by itself without blasting. It is the action of the explosive in the boreholes that does it. When we consider that we need a pound or two of explosive for every cubic yard of rock to be fragmented, and a pint of borehole volume for each pound of explosive, we see that the process of blasthole charging is an important element in the whole process of rock blasting.

Jan 1, 1975

By Mehdi Noori, Atefeh Azizitorghabeh, Fereshteh Rashchi, Ataollah Babakhani, Sarah Mahmoudi

The focus of this research was to evaluate the synergistic effect of bis(2,4,4-trimethylpentyl) phosphinic acid (CYANEX 272) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), diluted in kerosene, on the extraction and separation of Co(II) and Li(I) from synthetic sulfate solution. The results indicated that using a mixture of CYANEX 272 and D2EHPA was efficient in extracting and separating Co(II) from Li(I). The optimum ratio of CYANEX 272/D2EHPA was found to be 5:1, in which the highest separation factor was obtained (5973.23), and ΔpH0.5 was 4.10. Adding tributyl phosphate (TBP) as a modifier and increasing the temperature improved the metals’ separation rate and extraction efficiency. Thermodynamic studies were also carried out, and ΔH, ΔS, and ΔG values were computed, revealing the endothermic nature of Co(II) and Li(I) extraction by CYANEX 272/D2EHPA mixture. The conducted experiments for the McCabe–Thiele diagram showed the possibility of using two stages to extract over 99% of Co(II) and Li(I). Slope analysis and Fourier transform infrared spectroscopy (FT-IR) were employed to comprehend the Co(II) and Li(I) extraction mechanism using a mixture of CYANEX 272 and D2EHPA.

Jan 17, 2022

By Michael Casson

With the mining industry changing rapidly due to mergers, acquisitions and fluctuating market pricing, today?s market for coal, minerals, ores and aggregates demands electrical apparatus that perform every time with maximum efficiency and with consideration for personnel safety. This is especially true in existing mining operations where every payload counts. Draglines are the workhorses of surface mining operations, and reliable and efficient operation is absolutely critical to success. However, the inherent disadvantages of using dc motors and motor-generator (MG) sets can significantly impact productivity and return on investment (ROI).

Jan 1, 2013

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By Michael Ferrell

The primary reason pigments are used in plastics is to impart a desired color to the plastic. Color is one of the more important assign considerations associated with today's market oriented society. Secondary reasons for adding pigments to plastics include: 1. Improved UV stability 2. Enhancement to selected physical properties 3. Changes in optical properties Pigments may be used at loadings as high as 20% or as low as .001%. Generally the loading levels are between 0.2% and 2.0%. Pigments may be added to the plastic either by the manufacturer of the plastic, or by the user of the plastic. If the customer buys material that is already colored, it is referred to as "pre-colored". If the customer buys uncolored plastic and adds colorants, the process is referred to as "in-house" coloring.

Jan 1, 1985

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022