Search Documents

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept's economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

By R. M. Parlman

Interest is increasing in obtaining incremental improvements in mineral recoveries in flotation processes because of changing world economic conditions. Research on collector reagents, long indispensable components in flotation systems may provide the cheapest and simplest route to higher metal recoveries. Sulfhydryl group - containing compounds (-SH) and their salts, e.g., dithiophosphates, xanthates and a few other derivatives are commonly used to promote the flotation of sulfide minerals. Alkyl mercaptans, another class of sulfhydryl compounds, have long been known to have collecting properties but have been relegated to dormancy for one reason or another. This paper reports results from new investigations of alkyl mercaptans, trithiocarbonates, and a petroleum oil with a variety of western domestic and Canadian ores for copper and molybdenum sulfides recovery. Specific opportunities are pointed out to the industry for mineral recovery enhancement through the use of the proper reagent combination.

Jan 1, 1980

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By Roger G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of Project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the Project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mecha¬nics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1983

By A. D. Davis

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well defined drainage in a heavily mineralized area of the northern Black Hills. The basin contains numerous inactive and abandoned mines as well as a currently active heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer and thus can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted, and two abandoned mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 1997

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

The Jiboia heavy mineral sands deposit is a new discovery associated with the São Francisco River delta on the northern coast of Sergipe state. The identified resources are part of the much larger mineralized trend. Mineralization is hosted in paleodunes deposited on Holocene marine terraces (Fig. 1). The dunes are up to 30 m above sea level, and mineralization occur from 6 m above sea level upward. The main ore minerals constitute pseudorutile, ilmenite, zircon, rutile and monazite. This work presents a thorough characterization of the mineralogy and granulometric distribution of the Jiboia orebody.

Apr 1, 2024

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

By Nikhil Dhawan, Amit Barnwal

The present study reports a processing route to recover metals from integrated circuits of discarded random access memory (RAM) units containing ~ 66% printed circuit boards and ~ 33% integrated circuits. The integrated circuits are manually separated, grounded, classified, and subjected to water fluidization for the effective separation of metals. The significant separation was achieved via water fluidization, and the underflow fraction was magnetically separated. The magnetic fraction was thermally exposed in a muffle furnace, and the process optimization was carried out using a Box-Behnken statistical design. The detailed characterization at subsequent steps significantly aids the understanding of metal-plastic separation and enrichment. A concentrate containing 97% metals (Fe-59%, Ni-9.5%, Cu-7.7%, Sn-13.4%, Pb-5.6%, Ag-1.6%) with 96 wt% recovery can be recovered from discarded IC units. The process pursued is simple, adaptable, and environment-friendly, and the product can be used in conventional smelters.

Jun 23, 2020

By Ben E. Lusk

First of all let me say what a genuine pleasure it is to be here. Acapulco certainly is a beautiful change. I'm going to spend sometime talking about change, because frankly I'm astounded at the rate of change in our world today. One good example of this, reminds me that the first time I spoke before the AIME two years ago, we were at the Ramada Inn in Beckley, West Virginia. Today we're at the Princess Hotel in Acapulco, Mexico. Now that's what I call a change. Seriously though, I'm sure you've all heard it said that the most consistent thing about our society is its constant change. Five years ago, no one could have predicted the changes we experienced in the United States during the first half of the 1970's. In the past twenty-four months alone, we have seen two presidents, three vice-presidents and hundreds of administration and government personnel changes. We have stumbled from one social crisis to another, while suffering through rising inflation, major energy shortages and labor unrest that could plunge us into a full scale economic depression. In view of these constant and unpredictable changes around us, it's obvious that we must learn to deal with change and "roll with the punches" if we are to survive. A controversial book published recently, explores in detail the various aspects of change and its impact on man.

Jan 1, 1974

By L. E. Mercando

The proposed Flambeau Mining Project is based on a high grade copper deposit located approximately one mile southwest of Ladysmith, Wisconsin. The project involves only the mining, crushing, and shipping of ore to facilities outside of Wisconsin for processing. The Wisconsin environmental regulations include provisions for identifying wetlands, the requirements for minimizing the disturbance of wetlands, and the need to establish new wet-lands to replace any wetlands which have to be disturbed.

Jan 1, 1991

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022

By Xiaodong Yu, Jinxia Zhang, Fusheng Niu, Hongmei Zhang

The three-dimensional (3D) fractal dimension is an important parameter to analyze the 3D structure and flocculation effect of the hematite flocs. In this work, the 3D fractal dimension of hematite flocs was predicted by establishing the particle swarm optimization (PSO) algorithm optimized with the back propagation (BP) neural network (PSO-BP). The proposed model considers four factors, namely, the flocculant quantity, flocculation time, stirring speed, and temperature, as the input parameters. We normalize the input data during the preprocessing stage. The BP neural network was optimized by using the PSO algorithm for realizing the 3D fractal dimension. The prediction accuracy and effectiveness of the model were evaluated. The experimental results showed that the predictions performed by the proposed PSO-BP neural network were better than that of BP neural network. In addition, the root mean square error (RMSE), mean squared relative error (MSRE), mean absolute error (MAE), and mean absolute relative error (MARE) of the proposed model are lower, compared with the errors of the BP network. Similarly, the measurement coefficient R2 of the proposed model is higher, compared with the BP network. The maximum absolute error of the model is 0.0772, the maximum relative error is 0.02405, and the regression coefficient r is 0.98592. These results showed that the proposed model has a good performance and high prediction accuracy. When verifying the practicability and the effectiveness of the proposed PSO-BP model, the prediction results of 10 groups of hematite flocculation experimental data under different conditions showed that the prediction value of the proposed PSO-BP model was closer to the ground truth as compared to the BP model. Therefore, the proposed model is suitable for predicting the 3D fractal dimension of hematite flocculation.

Oct 3, 2022

By S. S. Szoke

The concrete masonry industry, represented by the National Concrete Masonry Association has significantly expanded its markets since the industry's inception. The concrete masonry industry has developed and refined concrete masonry units by producing a variety of quality products on automated machines. In the sixties, architectural concrete masonry units gained popularity. In the seventies, the concrete paver market expanded. In the eighties, segmental retaining wall units became popular. The industry continues to research and develop new products and applications for concrete masonry to satisfy the needs of designers, specifiers, installers and owners. Both existing and innovative technologies in the concrete masonry industry are discussed.

Jan 1, 1993

By K. S. Whiting

Elevated concentrations of copper, cobalt, and arsenic within the Panther Creek Basin sediments in north central Idaho prompted an evaluation of the sources of the metals. Potential tailings and waste rock source samples collected at the head of Blackbird Creek were compared to sediment samples in the Panther Creek Basin using electron microprobe techniques. The mineral types, degree of alteration, and the morphology of the metal-bearing sediment grains within Blackbird and Panther Creeks were found to consist of copper-, cobalt-, and arsenic-bearing sulfide minerals.

Jan 1, 1997

By Kevin B. Doyle

Virtually all industries use sulphur in some form. About half of the world's production is used in the production of fertilizers. Sulphur is produced in one form or another in over sixty countries in the world. The major producing countries, in order of importance, are: U.S.A., Canada, U.S.S.R., Poland, Japan, France, Mexico, and Spain. Canada is the largest exporter of sulphur presently supplying about 30% of the world elemental sulphur export trade. It has held this position since 1968. World sulphur resources are virtually unlimited. Future world competition will come from Iraq and other Middle East countries as well as Central and South America.

Jan 1, 1978