Search Documents

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By F. Wendling, R. C. Nascimento, S. S. Wendling

"The objective of this research is to study the quality of blast-furnace iron ore pellets with binary basicity 1 fired on a pilot scale using the two main firing processes that are presently in use in the world and comparing them. Currently, the great majority of pellet producers use the traveling grate process because of its higher production capacity. In this study, the physical and chemical qualities of the pellet feed, limestone, anthracite and bentonite were determined and the amount of additives for a blast furnace pellet with the defined basicity was calculated. The physical properties of the green and dried pellets were determined accordingly. Produced pellets, after being fired on a pilot scale using traveling grate and grate kiln, were subjected to chemical analysis and physical testing. No significant difference was observed in the metallurgical quality — that is, reducibility index (RI), reducing disintegration index (RDI) and swelling index (SWI) — of the pellets produced by both processes. However, a comparison of cold physical tests — tumble and cold compression strength — shows improved quality of the pellets fired using the grate kiln process.IntroductionThe development of human civilization owes much to iron and steel (Sun et al., 2015). Iron is the most used metal in the world, and it is the main component of steel, which is present in materials for structural engineering, automotive and general industrial applications (Liu et al., 2014). Increased global demand has led to a decrease in the resources of ore with high iron content (Zhang et al., 2015), and currently 95 percent of the iron ore in China needs processing before smelting as its iron (Fe) content is only about 30 percent on average (Liu et al., 2014).Pelletizing is a process to economically agglomerate iron ore pellet feed into pellet form. After balling, green pellets are conveyed to the final step of the manufacturing process (Pena, 1982). The process is a multifaceted one, involving high temperatures, air flow gas turbulence and complex equipment geometry (Larsson et al., 2009). The pellets are fed into blast furnaces, which are now predominantly used in the extraction of iron. Ore processing also requires physical separation, including crushing, grinding and water removal (Sun et al., 2015).The increase in steel consumption favors the exploitation of low-concentration ores and the production of pellets (Halt and Kawatra, 2014). Pellet quality is affected by various factors, such as their physical and chemical characteristics and their temperatures and residence times in the furnace (Halt, Silva and Kawatra, 2015). Different geological settings lead to a wide range of different minerals (Graça et al., 2015).This work aims to generate important information for the pellet industry in the area of physical and metallurgical qualities of the agglomerates obtained by two processes: traveling grate and grate kiln."

Jan 1, 2017

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.

By Leonard Weixler, Peter Halbach, Michael Jarowinsky, Johannes Post

Germany as an industrial nation is highly dependent on the import of mineral or metal resources. Sources which have not been considered until now are the marine mineral resources (MMR), which in recent times are enjoying more and more increasing interests and which might provide in the future a considerable contribution to the supply security on metal resources not only for the industrial countries. Backed up by the German government’s "National Masterplan Maritime Technologies" (NMMT) and corresponding industrial R&D-activities, the idea and the advantages of deep-sea mining is gaining more and more interests and supporters with respect to industrial and political considerations on strategic raw material resources as well as on the development of deep-sea mining technologies. The NMMT aims to initiate growth and increase the competitiveness of the German maritime industry on international markets and covers about 10 different marine and ocean technology sectors including deep-sea mining.

Sep 1, 2014

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By R. Curtis

To achieve compliance with 2015 EPA Tier 4 Final regulations, which permit only around 10% of Tier 3 particulate matter (PM) and NOx emissions, a number of technologies are being implemented. Use of a fuel borne nanoparticle combustion catalyst reduces the level of PM and unburned hydrocarbons exiting the combustion chamber, alleviating the burden on downstream exhaust after-treatment systems. The impact of an iron-ceria combustion catalyst (GO2) on carbon oxidation kinetics and on diesel engine emissions is presented. The iron-ceria nanoparticles catalyze carbon oxidation at lower temperatures and increase the oxidation rate by a factor of 18 at 400 °C. Engine tests on a generator powered by a John Deere Model engine and field tests on a Cummins ISC 330 tractor truck and CAT 3508B propulsion engines are presented. Use of GO2 resulted in a reduction in PM10 (particulate matter under 10 um) emissions of up to 26% and a hydrocarbon emission reduction of up to 41%. NOx emissions did not increase in these trials and the amount of change depended on engine type. Application of this fuel borne technology for emissions reductions in mining equipment offers significant benefits.

Feb 27, 2013

By Alfred Weiss

Selecting a minicomputer is not unlike selecting a costly piece of mining equipment such as a truck, shovel, crusher, or conveyor belt system. A marked difference might lie in the frequency at which such selection takes place; another difference might be mine management's familiarity with mining equipment vis a vis a minicomputer. These basic differences might prompt a mining company to seek the aid of a consultant when selecting a minicomputer system. Advantages and Disadvantages The fundamental advantage of employing an independent consultant is that it provides management with a source of knowledge and breadth of experience not readily available within the organization. If the consultant has a minerals background, such knowledge and experience are further enhanced by actual experience in exploration, mining, and mineral processing. If the consultant has worked within a mining company, such hands-on experience is supplemented with a meaningful understanding of the client's business; this facilitates communication between the consultant and members of the client organization. The consultant has been, so to speak, "in the client's shoes." There are several other advantages. Since computer systems cut across organizational boundaries, the independent consultant may be able to move within the organization more easily than an inside staff person to collect necessary information. Also, detachment from any manufacturer should provide the client with an objectivity and a set of recommendations as near optimal as feasible. The principal disadvantages lie in the area of continuity and accountability. Once the consultant's report has been submitted and his recommendations implemented, a discontinuity might occur. Also, if implementation does not provide the desired results, the consultant might not be available to correct the situation or account for actions taken. Proper selection of consultant services, relative to kind and duration, and the consultant's method of operation, will often prevent many of these aftereffects. Services Offered The professional consultant can help a client: •Define and summarize information systems technology* needs; • Evaluate alternatives such as in-house capability and capacity, time-sharing, or service bureaus; • Prepare a formal request for proposal (RFP) to be submitted to vendors; •Evaluate vendor proposals; •Evaluate the economics of lease vs. purchase; and •Assist in the conversion and installation. Thus, consulting services may range from evaluating an existing system and upgrading to a larger piece of equipment, to selecting a new first-for-the-organization computer. First, Define and Summarize Needs Regardless of circumstances, the most valuable document required before equipment selection is the information system plan (I/S plan). It helps insure that the company's information needs are met in a cost-effective manner. An I/S plan is usually a comporient of the mining company's overall business goals. Since an I/S plan is a formal vehicle for establishing and communicating the direction the organization intends to take to satisfy information requirements needed to achieve goals and objectives, most initial systems services are likely to center around creating such a document or updating an existing document. The trend toward company-wide I/S planning is increasing in the mining industry; however, smaller scale efforts focused at the information systems needs to support an individual

Jan 11, 1981

The 2003 SME Annual Meeting and Exhibit will take place Feb. 24-26 in Cincinnati, OH. The meeting will feature a host of special symposia and programming geared toward the industrial minerals and aggregate industry sectors. This programming focus is particularly relevant for this annual meeting, as it will be hosted in the center of America’s transportation hub and industrial mineral center. Cincinnati, located on the Ohio River, is key to the movement of America’s supplies and construction material needs.

Jan 1, 2003

By Ashis Bhattacherjee, Rahul Upadhyay, Nearkasen Chau, Aditya Kumar Patra, Dhanjee Kumar Chaudhary

Heavy earth-moving machineries used in open-pit mines intensively expose the drill operators to whole-body vibration and shocks and thus to musculoskeletal disorders. The roles of an individual, machine, and rock-related factors in their exposure remain poorly understood. This cross-sectional study investigated their role among 39 drill operators from Indian iron ore mines. It shows that 70% of the operators were exposed to high levels of vibration, above the limit values recommended by ISO 2631-1. Multiple linear regression models showed that the whole-body vibration and shock exposures were strongly associated with operator’s age, drill machine model, rock’s hardness, uniaxial compressive strength, and density. The role of body mass index was close to significance (p = 0.08). Univariate analyses found that drill’s age, seat pad thickness, and seat backrest height were also strong predictors. These results help in identifying risky operators, materials and occupational situations, and in implementing appropriate prevention and intervention to reduce and monitor the exposures and health risk.

By Steven Hoerger

Newmont Mining has a large, integrated gold-mining operation in northern Nevada with several mines, stockpiles and processing facilities. There are more than 90 defined metallurgical ore types and more than 60 defined gold-recovery process options. Newmont developed a mine plan and process model to take better advantage of the available synergies at its Nevada mines. This plan includes a mixed integer and linear programming optimization tool. This system is maintained and operated by a Nevada planning group. Standard in-house planning software tools and methods have been implemented at all mine sites. These changes have allowed a reduction in mine engineering staff and have increased the effectiveness of mine planning.

Jan 1, 1999

By W. F. McDermott

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three- year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1968

By B. A. Ridolfi, S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By L. J. Blatnica

Throughout the 1980's the tem Mine-Wide Monitoring System has had various meanings for manufacturers of these systems and underground mine operators alike. System suppliers had visions of grandeur in the early 80's as they envisioned each mine, that has more than a single section, installing a computer based monitoring system to provide surveillance, control and documentation of the entire mining operation, including everything from a single heat detector to the weekly payroll. In a few cases this may have become reality but the truth is these systems have quietly become a steady but unspectacular workbase for the modern mining industry of the 1990's. As it exists today the total market for underground monitoring systems may not exceed $10 million annually. Suppliers have lowered their expectations of the dollar value of this particular market. Some were entering a new market because of experience with computer based data acquisition systems. Others had been active in the mining industry for years with more traditional equipment (communication systems, methane monitors, safety equipment, etc.) and decided to become involved with Mine-Wide Monitoring Systems.

Jan 1, 1990

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.