Search Documents

In June, 1,334 underground construction and tunneling professionals gathered in Toronto, Ontario for the 2007 Rapid Excavation and Tunneling Conference (RETC). This biennial event, sponsored by SME, is one of the global underground construction industry?s major events. And this year?s RETC was the first one that included the new Underground Construction Association. [ ] (UCA) of SME. In addition, the conference?s exhibit attracted 125 equipment and service providers. The next Rapid Excavation and Tunneling Conference is set for June 14-17, 2009 at Caesar?s Palace, Las Vegas, NV.

Jan 1, 2007

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By P. Harris, G. Groenmeyer, L. Parolis

The effect of molecular weight, charge and the presence of the cations Ca2+, Mg2+and K+ on the adsorption of carboxymethyl cellulose on pure talc obtained from Balmat, New York have been investigated. Higher adsorption densities were obtained in the presence ofCa2+ and Mg2+ ions than with K+ ions and higher ionic strength solutions resulted in higher adsorption densities. Changing the molecular weight did not influence the adsorption however increasing the charge (DS) of the polymers resulted in lower adsorption densities.

Jan 1, 2004

The use of belt air in underground coal mines has been a continuous discussion since it was first introduced in the Federal Coal Mine Health and Safety Act (Coal Act) of 1969. Although the Coal Act prohibits the use of belt air to ventilate active workings, there were two exceptions prior to the 2004 Final Rule. There have been several major studies/rule-proposals by MSHA since 1985 and the most recent of which is the Technical Study Panel (TSP) established by the Mine Improvement and New Emergency Response (MINER) Act of 2006 to study the use of belt air and related issues. This paper reviews the history of belt air use, its associated controver-sies, and more specifically, the 20 recommendations unanimously approved by the TSP.

Jan 1, 2009

By W. H. Pomroy

In its 2001 diesel particulate matter (DPM) rule for metal and nonmetal underground mines, MSHA established an interim concentration limit of 400 micrograms of total carbon (TC) per cubic meter of air (400TCµg/m3), and a final concentration limit of 160TCµg/m3, to be phased in over five years. Following a court challenge to the 2001 rule, MSHA, industry and organized labor reached a partial settlement of the litigation under which the agency agreed to issue a proposal to amend the 2001 rule by, among other things, changing the surrogate from TC to elemental carbon (EC), applying MSHA's traditional hierarchy of controls, and revising requirements for one-year special extensions for complying with the final DPM exposure limit. MSHA issued a final rule in 2005 converting the interim concentration limit from 400TCµg/m3 to 308 micrograms of EC per cubic meter of air (308ECµg/m3) based on a miner?s personal exposure. Pending further rulemaking, MSHA retained the final concentration limit of 160TCµg/m3. In May 2006, MSHA issued a final rule that clarified that the final limit of 160TCµg/m3 would be based on a miner?s personal exposure rather than as a concentration limit. The 2006 rule also phased in the final DPM limit in three steps over two years, beginning in May 2006 at 308ECµg/m3, followed eight months later in January 2007 with a limit of 350TCµg/m3, and finally reaching 160TCµg/m3 in May 2008. Also in the 2006 rule, MSHA committed to converting the 160TCµg/m3 limit to an EC limit in future rulemaking. This paper reviews the DPM exposure limits in the context of the MSHA rulemakings and discusses the DPM engineering controls that were utilized by mine operators to attain compliance with each progressively lower limit.

Jan 1, 2009

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By S. A. Shuey, P. Taylor

The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of “electronics” as well as the constant change in materials of construction coupled with the speed at which electronics are changing. CSM researchers have undertaken a survey of the current state of pyrometallurgical processing of e-waste. This base-line will set the stage for the development of new recycling technology at CSM.

Jan 1, 2004

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By U. Thorley

Management of mine and tailings reclamation activities by surface mining oil sands operations in Alberta, Canada is experiencing increased national and international attention. Of particular concern is the ability of existing mines to execute and fund reclamation activities. Concern stems from a lack of demonstrated tailings reclamation technologies, perceptions of a poor track-record of reclamation activity by industry, and a lack of transparency with respect to the potential cost of reclamation activities relative to the monies secured in Alberta?s Environmental Protection Security Fund (EPSF). Limited information is publicly available regarding reclamation costs and technologies. Available data typically comes from disparate sources. This paper examines the expected costs of oil sands reclamation activities through a study of corporate Asset Retirement Obligation (ARO) liabilities, the Province of Alberta?sEPSF, and published data relating to reclamation costs.Issues relating to current liability funding are introduced.

Jan 1, 2011

By C. A. Young, R. G. Robins, E. J. Dahlgren

The formation of copper thio-complexes in sulfide solutions has been recognized for many years and the measured solubilities of certain copper sulfide minerals attributed to these complexes. Attempts to model this system have proposed either copper(I) or copper(II) thio-complexes, and these have been incorporated into computer programs for generating stability diagrams for the copper-sulfur-water system in order to delineate the region where the reductive dissolution of copper sulfide minerals is likely. In this paper it is proposed that the dissolution of copper from both ore bodies and sulfide tailings can be explained by the formation of the cupro-thio-complexes under anaerobic conditions. Stability diagrams are presented to depict the region and extent of the solubility.

Jan 1, 2001

By N. C. Trivedi

Natural calcium carbonate, commonly known as limestone is an abundant resource pretty much worldwide. Calcium carbonate occurs naturally as the main constituent of chalk, limestone, and marble. One of the unique characteristics of this abundant mineral is its versatility. Major markets for calcium carbonate are: paper, plastics, caulks and sealants, carpet backing, paint, and food additives. This broad spectrum of consuming industries has warranted producers of this industrial mineral to be innovative and quality focused simply to meet the ever increasing demands for performance. This need for improving performance of calcium carbonate has led to the development of new sources of calcium carbonate, natural as well as synthetic.

Jan 1, 2002

In the present study, we have investigated the conditions for the formation of bubble clusters and the effect of well-defined agitation on the stability of clusters. A specially designed cell was used in which bubble clusters could be formed at the surface of a porous block in a fluidized bed of relatively coarse hydrophobic silica particles. The clusters then rose through a flow field of known turbulent characteristics. The size of the clusters before and after passing through the turbulent zone were measured using a high speed camera. The influence of shear rate on the deformation of the bubble clusters was investigated. The results showed that the Kolmogarov microscale was much smaller than the maximum cluster size, suggesting that the breakage of the clusters was mainly due to interaction with clusters in the inertial convection sub-range.

Jan 1, 2009

The residues produced during the incineration of leather scraps contain significant amount of chromium which can be recovered and reused in the tanning industry. The objective of this study is to develop a cost effective method for chromium recovery from leather ashes produced during the incineration of leather scraps using a fluidized bed incinerator. The entire process investigated involves fusion of leather ash with sodium carbonate in air to oxidise chromium to sodium chromate, leaching with distilled water to dissolve chromates, and chromium reduction from the hexavalent to trivalent state by sodium thiosulphate solution. The main factors affecting chromium extraction, such as temperature, reaction time, and sodium carbonate to leather ash ratio, were investigated. Based on the results obtained, almost 100% Cr extraction can be obtained at 700°C fusion temperature, sodium carbonate to ash weight ratio equal to 3 and retention time longer than 50 min.

Jan 1, 2006

By E. Shelobolina, S. M. Pickering, J. E. Kogel

A long history of weathering and bacterial alteration processes have transformed Georgia’s Coastal Plain kaolins from dark organic muds to recrystallized white pigment-grade industrial clays. A sequence of six stages in development of these valuable mineral deposits is outlined over their Late Cretaceous and Tertiary deposition and alteration history. Anaerobic and aerobic iron oxidizing and iron-reducing bacteria are present in the Georgia kaolins. These bacteria may have had a major role in iron and organic matter removal during several of the alteration stages that occurred over the past 60+ million years. Iron was likely solubilized by both iron-reducing and iron-oxidizing bacteria, depending on availability of Fe(II), Fe(III), and NO3. Thus, over long periods bacterial activity slowly led to nearly complete groundwater removal of iron from the kaolin deposits. Further bacterial iron removal on an industrial process scale may eventually prove feasible. “Without the multitude of living reactions as channels for energy and electrons and without the enormous capability of life to transfer with and against chemical gradients, there would be practically no or at least a very reduced geochemical rock cycle on this planet.” (Krumbein and Dyer, 1985, p. 157)

Jan 1, 2002

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By K. N. Han, N. S. Kim, H. Yoon, J. S. Sohn

The leaching behavior of silver and silver oxides in ammonical solutions has been studied. The current study is concerned with an effective recovery of silver from secondary sources such as spent silver batteries. Silver associated with these batteries appears in various forms including metallic silver, argentous oxide, Ag2O and argentic oxide, AgO. The leaching behavior of metallic silver in ammoniacal solution has been studied using an electrochemical mehtod. Oxidants used in this study include hyperchlorite, hydrogen peroxide, bromine and iodine. Results on cyclic polarization and Tafel plots on the silver anode in ammoniacal solutions are presented and the results are discussed. The dissolution rate of metallic silver in ammoniacal solutions is also compared with those of silver oxides.

Jan 1, 2002

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Most of the future phosphate resources in Florida, which accounts for 70  percent of production in the United States, are contaminated with too much dolomite that is difficult to remove with existing industrial practices. The low-grade ore quality coupled with increased phosphate demand is of concern to the Florida phosphate industry. In order to resolve the dolomite issue, various beneficiation technologies were designed and evaluated, but none have been sufficiently successful [1]. 

By Steve Kral

Conference themes are usually chosen by organizers to reflect the current state of the industry. The Colorado Section MPD came up with what may be the most appropriate theme of a mining conference during the last few years. The local SME MPD section’s theme of its 56th annual conference was “The Wild, Wild World of Mining.” The current boom can be felt in all aspects of the industry, including exploration, mining, processing, sustainability, and economic and political issues. Each of the 25 speakers at the conference, held in Colorado Springs, CO, touched on how the boom has impacted each of those aspects. The meeting attracted about 110 people from around the world.

Jan 1, 2006

By M. J. Gregory

The Pebble Cu-Au-Mo deposit in southwest Alaska is one of the world's largest porphyry deposits. The western part of the deposit was discovered by Cominco America in 1987, who sold the project to Northern Dynasty Minerals Ltd., in 2001. Northern Dynasty discovered the high-grade eastern part of the deposit in 2004 and went into a 50:50 partnership with Anglo American PLC in 2007, forming the Pebble Limited Partnership (Lang et al., 2008). The Pebble Limited Partnership has continued to delineate the deposit through diamond drilling with the most recent resource estimate released in February 2010 (Pebble Limited Partnership, 2010). The Pebble deposit mineral resources comprise 5.94 billion tonnes of measured and indicated resources grading 0.78% Cu EQ, containing 55 billion pounds of copper, 67 million ounces of gold and 3.3 billion pounds of molybdenum. Also delineated are 4.84 billion tonnes of inferred mineral resources grading 0.53% Cu EQ, containing 25.6 billion pounds of copper, 40.4 million ounces of gold and 2.3 billion pounds of molybdenum (Pebble Limited Partnership, 2010). Resources are calculated using a 0.3% Cu EQ cutoff. GEOLOGY AND MINERALIZATION Deposit Geology The Pebble deposit is located in the Kahiltna terrane, between terminal strands of the north-east-striking Lake Clarke strike-slip fault. This fault represents an accretionary boundary and separates the Kahiltna terrane to the north-west from the Peninsular terrane to the south-east (Lang et al., 2008). The Pebble deposit represents a large magmatic-hydrothermal system centered on a group of 90 million year old porphyritic hornblende granodiorite intrusions. An east-west cross section through the southern part of the deposit (Figure 1A) shows the typical relationships between the various rock units which host sulfide mineralization. Sub-parallel ~96 million year old granodiorite and diorite sills were intruded into siltstones of the Jura-Cretaceous Kahiltna flysch. In the west, these sills were cut by a ~96 million year old alkalic intrusive complex composed of porphyritic monzonites and monzodiorites and related intrusion breccias (Bouley et al, 1995). The mineralized 90 million year old hornblende granodiorite intrusions cut all rock types and comprise four small stocks in the western part of the deposit and a larger pluton in the eastern part of the deposit. Recent deep drilling indicates that these intrusions coalesce at depth. The strongest porphyry-style mineralization is centered on the eastern granodiorite pluton and extends into the surrounding rock units (Figure 1A). The western half of the deposit crops out at surface, whereas the eastern side is un-conformably overlain by a cover sequence of Late Cretaceous to Eocene sedimentary and volcanic strata. The deposit was tilted 20º to the east during the Eocene.

Jan 1, 2012