Search Documents

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By D. Tao

The reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In such a process quartz is often floated with ether amines (R?O(CH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of hematite does not work well if a certain amount of slime is present in ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the flotation efficiency of iron ore flotation by use of a new type of depressant for clay and iron minerals, i.e., GP clay binder. It is postulated that the GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It is further theorized that the clay binder helps depress hematite flotation due to its unique chelating ability to iron ion. The results from this study clearly show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing concentrate grade to 67.08% and iron recovery to 78.15% simultaneously. Key words: Clay Binder; Depressant; Iron Ore; Flotation.

Jan 1, 2009

By C. R. Landis

The Wyoming bentonite industry finished 2005 with strong growth. For most of the markets, demand exceeded supply. The industry continues to be heartened by the strength of its longtime markets, oilfield and iron ore pelletizing markets. But overall, all of the major markets enjoyed good to excellent commercial conditions. Growth at the macroscale was fueled by the continued strong domestic economy, by the exchange rate of the U.S. dollar in global markets and by strong worldwide global demand. As result, two new greenfield operations are in the early stage of development in the Wyoming region for the first time in more than two decades.

Jan 1, 2006

By James W. Stewart, A. C. Colvine

Introduction Precambrian shield terrains the world over are experiencing an unprecedented level of concerted exploration for lode gold deposits. Reasons for this include: • The increase in the price of gold (following 40 years at $1.13/g or $35 per oz) has transformed targets that were once unattractive into viable exploration propositions. • The relatively suppressed market for other metals produced from shields (base metals, nickel, iron, and uranium) has further focused exploration attention on gold. • The preeminence of gold production from rocks of early Precambrian age, as shown in Fig. 1. • The relatively high grade of gold in these mines (averaging about 10 Wt or 0.29 oz per st) permits profitable extraction even under depressed gold prices. A number of these mines have been in continuous operation for more than 50 years. • The recent discovery of the major Hemlo deposit, in well exposed rocks adjacent to the Trans Canada Highway, has had a world-wide impact. This demonstrates that a major new deposit can be found even in an accessible, well exposed area of a shield; gold mineralization is susceptible to rational exploration; and new target types for gold exploration exist. This paper reviews exploration activity for gold in shield terrains worldwide (Fig. 2), excluding Early Proterozoic paleoplacers of the Witwatersrand type. Emphasis is on the Archean, which is traditionally the most productive part of the Precambrian shields. There is also an emphasis on the Canadian shield (Fig. 3) because of its vast areal extent and exceptionally broad range of mineralization styles. Geological Approach A basic problem exists in gold exploration when compared to exploration for base metal massive sulfides that predominated during the 1960s and 1970s. Gold concentrations cannot usually be detected by airborne geophysical instruments. The majority of massive sulfide deposits were detected using airborne electromagnetic detectors and magnetometers. A full 75% of Canadian gold discoveries can be credited to surface prospecting. The percentage is even higher in other countries. This observation allows for great optimism for two reasons: • Large areas of shield terrain are obscured by either surficial deposits (glacial tills, clays, and desert sands) or deep surface weathering. This makes them inaccessible to prospectors. Logic dictates that such obscured areas should have the same potential for gold concentration as has exposed bedrock. • The Hemlo style of mineralization, a roughly tabular ore body where gold is associated with disseminated sulfides, is different from the traditional prospecting target. The gold is hosted by discrete quartz veins. While it is true that limited discoveries were made at Hemlo more than 30 years ago, and this style of mineralization is present elsewhere, recent

Jan 12, 1984

By James Paone

Drillability of rocks by mechanical means is closely related to the physical properties of the respective rocks, Various approaches by previous investigators on rock drillability are presented, as well as recent techniques studied by the Bureau of Mines. The studies show drillability concepts based on (1) theoretical drilling equations derived from laboratory drilling experiments extended to field drilling results and on (2) a statistical method where multiple regression analysis is used to develop a prediction equation for drillability.

Jan 1, 1966

By J. T. Bartlett

Life-of-mine process simulation is an interdisciplinary effort and a useful means of thoroughly evaluating mining and minerals projects. Communication between geologists, mine planners, miners, metallurgists, and managers not only benefits each discipline but facilitates design of an efficient operation and allows for accurate forecasting of productions and cash flow. By focusing on the key areas: geology; mine design; waste dumps; stockpiles; metallurgy; weather data; tailings disposal; using contours, block models, mine plans, process flowsheets, design criteria, operating and control strategies, maintenance schedules, and operating costs to perform detailed daily simulation from start-up to shut-down; a comprehensive understanding for all disciplines is achieved. Construction of a METSIM model that includes all test work and project data from drill holes through net present value calculations brings the pieces together to achieve optimum process design, minimize operating problems and eliminate the term ?black box? from project meetings and discussions.

Feb 27, 2013

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By D. Stone, R. Pakalnis, B. Seymour

Most mines using backfill routinely carry out quality control (QC) testing of backfill mixes with unconfined compression test cylinders. This is true for paste operations, hydraulic fill operations, and cemented rockfill operations worldwide. However, a large number of mines simply do not prepare and test the backfill samples in a consistent manner and fail to properly analyze or interpret the test results. Conventional concrete test criteria are not applicable given the differences in the mix constituents and the fact that a large number of the backfill QC test cylinders typically fail to achieve the target strength. Standard industry practices are needed to improve the analysis and interpretation of QC test results and to provide a better means of determining if the backfill is achieving its intended target strength. This paper will attempt to lay the groundwork for standard industry practices and will address several key questions raised by operators, such as how laboratory test data compares to in-stope performance, and how many QC tests should fail before a red flag should be raised. INTRODUCTION Although paste backfill is widely used throughout the mining industry, cemented rockfill (CRF) remains as the backfill of choice in places like Nevada where very poor ground conditions mandate the use of underhand mining. The safety and stability of undercut entries beneath backfill is a function of the quality of the cemented fill, which is typically assured through routine quality control testing. In the absence of a backfill quality standard, most mines rely on concrete standards to design and interpret their backfill quality control programs. In the USA, these standards are developed and published by organizations such as the American Society of Testing and Materials (ASTM) and the American Concrete Institute (ACI). However, the application of these standards to cemented backfills can be very difficult owing to the high degree of variability in backfill mixes and the resulting variability in test results. To illustrate, the concrete industry standards denote that an acceptable (passing) test result occurs when the average strength of the duplicate test cylinders exceeds the target strength and no single test result deviates from the target strength by more than 10% (ACI 214R). Remedial measures must be taken if three consecutive tests fail. With mine backfills, it is safe to say that these criteria are rarely achievable. A further, more dramatic example is the accepted coefficient of variation for concrete QC cylinders. According to ACI 214R, the coefficient of variation (CV) should range from below 3% (excellent rating) to above 6% (poor rating). However, if this analysis method is applied to several backfill QC databases from operating mines, coefficients of variation are calculated on the order of 50%. Clearly, there is a need to develop better industry practices for assessing the quality of mine backfill and to assist mine operators with the interpretation of test results and the development of action plans in the event of undesired outcomes.

Jan 1, 2019

By Steve Kral

About 500 mineral-processing professionals from around the world gathered in San Francisco, CA in Oct. 22-27, 1995 for the XIX International Mineral Processing Congress (IMPC). Following the theme “Leading Mineral Processing into the 21st Century Through Advanced Technology,”186 speakers from 28 countries covered research and development activities and innovative processes. Subjects included comminution and simulation control, physical and chemical processing, flotation practices and fundamentals, precious metals processing and mineral waste and the environment.

Jan 1, 1996

By P. Todd, K. Dever, P. S. Mills, A. A. Campoli

Resin bolt performance is dependent on the size of the resin annulus, the difference between the hole and bolt radii. The vast majority of the millions of resin roof bolts installed each year in the United States employ an annulus of 0.125 or 0.188 inches. Short encapsulation pull tests with resin annuluses of 0.125 and 0.095 inch resisted an average of 2.25tons per grouted inch, with no significant variation. Resin loses to simulated fractures increased as annulus size decreased, with a minimum loss of35% and a maximum loss of 60% associated with0.188 and 0.095 inch annuluses, respectively.

Jan 1, 2000

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN ‘01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN ‘01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB are expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2002

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By Patrick J. Doig

The Lewis Street CSO Tunnel is an important element in the efforts of the Metropolitan Government of Nashville and Davidson County (Metro) to improve the treatment of waste-water in the area. The tunnel is approximately 1,675m (5,500ft) long with a finished diameter of 2,600mm(102inches). 116m (380ft) of tunnel was constructed in soil with the balance being in lime-stone rock. Excavation was with a 3,700 mm (12ft) diameter Jarva hydraulic shield in soil and a Jarva Mark 12 TBM in rock. The permanent lining of the tunnel comprised concrete pipe with steel end-rings and a vinyl liner. This paper describes the construction of the project with particular emphasis on the excavation and lining of the tunnel.

Jan 1, 1997

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By G. W. Toth

The coal mining cost models described in this paper represent a computerized estimating procedure for analyzing mining costs and requirements of proposed coal mining projects. Both surface and underground mining analyses can be conducted through the use of these models. These models were developed by the NUS Corporation for the Electric Power Research Institute (EPRI). The methodology design of the cost models follows a process engineering approach for determining mining requirements and costs similar to the logic typically employed in preliminary mine feasibility studies. All capital and operating costs associated with a new coal mining project are thereby estimated. The results of these analyses are then entered into a financial analysis framework which computes annual cash flow summaries, utilizing a profit and loss statement approach, to solve for either the coal value/ton (minimum required selling price) or the rate of return on equity for the project. The coal value/ton is also referred to as the economic cost of production (F .O . B. mine, including preparation).

Jan 1, 1980

By D. Bogh

Wound rotor motors are used in difficult mining applications where there is a need to start high inertia, hard starting loads while limiting inrush current They are recognized as robust and simple to control. This paper will cover the performance, specification, and important issues to be considered when applying medium voltage wound rotor motors in mining applications. Medium voltage grinding, crusher, and conveyor applications will be discussed. Specifically covered are motor efficiency, speed range, and rotor control. Crane motors often have wound rotor construction, but their load cycle and ratings are outside the scope of this paper.

Jan 1, 2011