Search Documents

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By I. Yildirim

Free energy of interaction between particles in water can be calculated if one knows the values of appropriate interfacial tensions, which in turn can be determined from the surface free energies of the particles involved. The latter can be determined using the Van Oss-Chaudhury-Good (OCG) equation. This method requires the measurement of contact angles of well-defined liquids on the surfaces of the particles of interest. In the present work, the contact angles were determined using heat of wetting, capillary rise, and thin-layer wicking methods. The results are compared, and the utility of the surface free energy data obtained from the contact angles are discussed.

Jan 1, 2002

By Samer Sadek

The Georgia Department of Transportation (GDOT) undertook an exploratory feasibility study to one of the most ambitious tunneling projects in the United States. HNTB Corporation was retained to perform the study, deemed the Atlanta North-South Tunnel, which is approximately 7 miles long and consisting of four lanes (or six lanes) starting at the southern terminus of SR 400 extending to the south connecting with the northern terminus of I-675, providing substantial relief to the Downtown Connector (I-75/I-85), the most congested portion of Atlanta?s freeway system. This paper summarizes the analysis performed during the first phase of this challenging assignment which, if constructed, would be one of the longest roadway tunnels ever built in the United States.

The 23rd annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Tucson Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 3, 2005. The Mining Foundation of the Southwest is a non-profit organization. It educates the public about the mineral industries and reports outstanding accomplishments in the fields of mining and the earth sciences. This year’s inductee, guest of honor and featured speaker at the banquet will be Pierre Lassonde, president of Newmont Mining and resident of the World Gold Council. He is one of Canada’s leading gold analysts.

Jan 1, 2005

By R. L. Zick, D. C. Finn

Introduction The high-density sludge process was originally developed by Bethlehem Steel Corp. for use on acid mine drainage (AMD) and diluted waste pickle liquor discharges requiring continuous chemical-treatment. This work began in the early 1970s and was first put into practical use around 1973. To date, there are approximately 15 operating systems that have been installed to treat mine drainage in the United States. In addition, there are another 10 systems installed outside of the United States. The dense-sludge process is an innovative and improved method for treating acidic metal-bearing streams in a manner that minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge-recycle process that forms particles with a low affinity for water. These particles are unlike conventional metal hydroxide solids that contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations that combine with calcium ions in lime-based treatment systems to form gypsum crystals. Compared to the form generated in conventional lime treatment systems, the physical form of the gypsum is radically altered when the dense-sludge process is utilized. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. The dense-sludge particles settle faster, dewater more readily, are more easily pumped and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered. In general, the conventional and dense-sludge treatment processes are very similar. The changes required to implement the dense-sludge process are minor, and, typically, much of the existing equipment can be utilized. The net results of the process are: reduced operational costs associated with sludge generation, improved process control (particularly pH control), reduced gypsum deposition (i.e., less scaling) on system components and reduced sludge generation resulting in less return water for treatment. Despite the relative simplicity of the process, the application of the technology requires careful discrimination, and the "experience factor" for implementation is an important consideration that should not be over looked.

Jan 1, 2000

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By R. Fernández, E. Marczak, A. Collins

Newmont roasting plant in Carlin, Nevada commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable that affected the structural characteristics of the calcine which, in turn, affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature was closely monitored since October 2000. Original design temperature was 550oC. Lower roaster temperatures of around 500oC resulted in gold recovery increase by more than 6 percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an “intelligent” process control system helped significantly in achieving steady low roasting temperatures thus achieving high gold recoveries between 92 and 93 percent. Under those conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease of gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g. porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2007

By Takuji Yamamoto

High-speed TBM excavation requires rapid ground assessment ahead of excavation, particularly in complex grounds. The Tunnel Reflector Tracing technology (TRT) developed by authors, uses seismic reflections to produce volumetric images of ground anomalies. To further minimize interruption in the TBM excavation the authors modified surveying technique switching from cable (wired) to radio (wireless) data acquisition system. This paper presents the outline of the Wireless TRT system, and compares the results for the wired and the wireless surveys. The comparison shows that the wireless system offers high precision data, is more efficient and economical and significantly less intrusive in tunneling operations.

By Don C. White

The Vulture mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11t(12.1 st) Au and 8t (8.8st) Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely dis¬seminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence, all dipping north about 35°. Early mining focused on the vein-hosted gold, particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pit mining of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry. The sill is a 350 m (1148 ft) long apophysis from a quartz mozonite stock to the west of the mine area. The stock has been dated at 85 my and contains abundant lesser gold occurrences in its core and about its margins. The Proterozoic rocks are notably lean in precious metals except where altered in proximity to the Creataceous stock and sill. Circumstances dictate an interpretation of epigenetic mineralization related to the Laramide intrusion.

Jan 1, 1990

By J. Barrett

State-of-the-art wireless communication and location-tracking technologies will dramatically change the face of mine worker safety. The MineTracer System developed by a Liberty Lake Washington company is a broad capability wireless sensor network based on a new breed of technologies known as wireless mesh systems. In this paper, R&D Manager Jim Barrett summarizes the balance of engineering tradeoffs that result in a system that (1) performs well, (2) is survivable against many types of mine accidents, (3) operates for many hours post-accident on battery power, (4) meets stringent MSHA requirements for intrinsic safety, and (5) is economically affordable for the mines.

Jan 1, 2009

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002

By L. "Andy" Anderson, Stephen N. Short, James E. Friant

Since the introduction of "boxhole" drilling in South Africa in 1973, the concept of a blind raise, drilled upward from below, has become an accepted mining practice. A combination machine, capable of constructing raises to a mining level below, or blind raising upward from a single setup position adds a further dimension in versatility. A machine with these dual operating modes was designated by The Robbins Company as the 53R and was introduced into the Western Deep Level Mines, South Africa in 1984. The unit is powerful (200 hp) and compact (18,000 lbs., in a 10 ft x 4 ft 5 inch x 4 ft 6 inch package). This paper describes the design considerations for the new machine, provides field data from early trials, and looks briefly at its overall market and potential.

Jan 1, 1985

By Yu-ren Jiang

Novel compounds of hydroxycarbamoyl carboxylic acids, including 2-hydroxycarbamoyl -3-methlcyclohexane carboxylic acid (HCMC), 2-hydroxycarbamoylmethyl decylen-4-yl carboxylic acid (HCDC) and 2-hydroxycar-bamoylmethyl tridecylen-4-yl carboxylic acid (HCTC) were synthesized. The flotation behaviors of diaspore, kaolinite and illite using these compounds as collectors were investigated. The flotation results revealed that the floatability of the minerals was, in descending order, diaspore and kaolinite, followed by illite, and the ability to collect the minerals was, in ascending order, HCMC and HCDC, followed by HCTC. At a dosage of 2×10-4 mol/L, both HCDC and HCTC show a strong ability to collect diaspore and a weak ability to float kaolinite and illite. The flotation recovery of diaspore is over 90% and that of kaolinite and illite less than 30%. Moreover, Fourier transform infrared spectroscopy (FTIR) spectrum and zeta potential, as well as the adsorption amount, indicated that the adsorption interaction between HCTC and diaspore was primarily a kind of chemisorption in the form of chelate rings, while the interaction between the collector and aluminosilicate mineral was dominated by physisorption. It was concluded that the novel hydroxycarbamoyl carboxylic acid compounds are highly selective collectors for the flotation of diaspore vs. aluminosilicate minerals.

Jan 1, 2011

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By L. M. Anisdahl

Ventiflex is a flexible ventilation duct system with a global market within mine and tunnel ventilation. The system is distributed in a wide range of qualities and dimensions. It is very important that ventilation systems are designed correctly in mines and tunnels. An incorrectly dimensioned system might result in bad air quality and too high costs. The objective of this study has been to assess some important design parameters for ventiflex comprising the friction loss factor for the duct wall itself, as well as the shock loss factors and the leakage factors for the different couplings systems. This has been obtained by carrying out a large scale experimental program on ducts with all the three different couplings: Velcro, zip and steel-ring. Pressure profiles and air flow rates have been measured, and based on these data the different factors have been calculated. The following results have been obtained: A friction factor l = 0,012 (K = 10) for the duct wall, a shock loss factor z = 0,0125 for velcro- and zip couplings, a shock loss factor z = 0,005 for steel-ring couplings, and a leakage factor f* = 0 mm2/m2 for all three coupling types. The latter result proves that no leakage is possible for a correctly installed duct with proper alignment. The results also confirm that ventiflex complies with class S, or better, according to the SIA-norm. However, whether ventiflex should be designed as class S, A or B according to the SIA-norm, depends on the particular application.

Jan 1, 2009

By A. A. Campoli

The U. S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6)tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of a longwall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

Jan 1, 2000