Search Documents

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By T. Arthur Palm, Stephen L. Bessinger

San Juan Coal Co. (SJCC) operates an underground coal mine near Farmington, NM. Continuous miners and a longwall produce 6.3 to 7.2 Mt/a (7 million to 8 million stpy). SJCC is owned and operated by BHP Billiton. The coal seam at SJCC has been shown to have a propensity for spontaneous combustion. As such, during the feasibility study for this project, it was elected to use a bleederless ventilation system on the longwall. Due to the combination of spontaneous combustion, methane liberation and, to a lesser extent, hydrogen sulfide, a typical wraparound ventilation system would not be appropriate. Three-entry gate roads are developed, and the longwall gob is sealed as mining progresses. SJCC uses a nitrogen injection system to continuously inertize the gob.

Jan 1, 2007

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By Y. Lahaye, O. Martinsson, B. I. Palsson

"Four main and three minor rare-earth-element (REE)-bearing minerals were identified and quantified in the Kiirunavaara apatite iron ore tailings using optical microscopy, an electron probe microanalyzer (EPMA) and a mineral liberation analyzer, and their chemical compositions were analyzed by the EPMA and laser ablation inductively coupled plasmamass spectrometry. REEs are shown to be contained in the minerals apatite, monazite, allanite, titanite, zircon, thorite and synchysite. In zircon, thorite and synchysite, they occurred in only trace amounts and contributed limited amounts to the total REE budget, and these are consequently of minor importance. Monazite occurred as inclusions in apatite and as free particles, 90 percent liberated. Allanite occurred to some degree in mixed grains with magnetite but also as free particles. Monazite mainly reported to the apatite concentrate, while allanite and titanite largely went to the tailings, the latter preferably to those fractions smaller than 38 µm. The amount of titanite in the finest tailings fraction was 2.3 weight percent, containing close to 1 percent REEs, with heavy rare earth elements (HREEs) making up 28 percent of the total REEs. However, a texturally distinct group of titanite grains showed an HREE/REE ratio of up to 67 percent. Furthermore, titanum dioxide analyses indicate that titanite is preferentially released into the tailings from the secondary magnetic separation step in the concentrator. Our data therefore suggest that titanite, occasionally enriched in HREEs, can be extracted from the processing stream and might thus be considered a new source for REEs at Kiirunavaara and similar deposits.IntroductionDeposits of apatite iron ores are the major source for iron in the European Union and are exploited by Luossavaara-Kiirunavaara AB (LKAB) in several mines in the Kiruna-Malmberget area in northern Sweden. Kiirunavaara is the largest of the apatite iron orebodies in Sweden, comprising more than 2 Gt of iron ore with 60 to 68 percent iron (Fe). At the end of 2015, the total accumulated production of crude ore from openpit and underground mining since the start of mining was 1,566 Mt, with ore reserves of 644 Mt grading 46.3 percent Fe (LKAB, 2016). The deposit defines a steeply dipping tabular body, approximately 6 km long and up to 180 m thick, extending at least 1,500 m below the surface. It is situated in the middle part of the Palaeoproterozoic Kiirunavaara Group of volcanic rocks and follows the contact between a thick pile of trachyandesitic lava and overlying pyroclastics (Martinsson, 2004)."

Jan 1, 2017

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

Many of the world?s largest existing mines are considering substantial step changes in production volumes, compensating for declining ore grades while trying to address increases in world demand for resources. The natural configuration of coal deposits allows for many mine development openings along the strike to access the ore body and thus increase volume. Similarly, with iron ore the nature of the deposits means that additional capacity can easily be added by opening up new mesas and providing extensions to infrastructure. On the other hand most of the non-ferrous metaliferous deposits form vertically and additional extraction volume comes from increasing depth. Underground mining from the base of the strata allows for large extraction rates, but block or panel caving operations develop at rates dictated by the geophysics of the overlying strata and the need for massive tunnelling developments to establish sufficient extraction points for high volumes. For really big mine production capacity, open cast mining still allows the easiest development of more massive mining techniques. But there remains the question of whether there are limits to how large an open cut mine can become in terms of throughput?

Feb 27, 2013

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By William R. Yernberg

The Society of Economic Geologists (SEG) held its biennial conference May 14 through 16, 2006, in Keystone, CO. SEG is an international organization with about 3,500 individual members with interests in economic geology. The 2006 SEG conference theme was “Wealth creation in the minerals industry — integrating science, business and education.” The conference exceeded expectations with 705 participants, including 102 students, from 44 countries. The conference featured 30 oral presentations, 24 professional posters and more than 70 student posters. The conference also included a trade show with 50 vendors, numerous field trips, workshops and social activities.

Jan 1, 2006

By Steve Skelhorn

Over the recent years, major advances have been made in design of precast concrete segmental tunnel liner. Starting from basic, parallel sided rings, we now have state of the art, universal rings incorporating custom tapers to suit individual requirements. At planning stage, the ring diameter is normally fixed and the ring geometry is one of the first items to be assessed. Obvious factors such as TBM layout and curve radius can constrain geometry; however, there others factors that should be considered in order to optimize production. This paper takes a look at the history of the segmental rings and criteria for ring selection, including: general ring geometry;; individual segment geometry; ring taper, and ring width. This paper also explores optimization of ring with a focus on constructability.

By I. T. Oramah

Despite the abundance of solid mineral deposits, Nigeria only earns about 0.5-1% of its current Gross Domestic Product (GDP) from the solid minerals sector. This is as a result of the dominance of the oil and gas industry, which has negatively affected the competitiveness of other sectors of Nigeria’s economy. The dominance of this industry has resulted in unemployment, poverty, hunger, domestic price inflation, corruption, unstable government, and higher exchange rates. These impacts are typical for economies suffering from the effects of "Dutch Disease" and the "Resource Curse". Community-based small-scale mining offers hope as an economic activity that can create wealth, employment, reduce hunger and poverty, and provide basic amenities for rural communities with solid minerals endowment. This study presents preliminary results of ongoing research into the prospects of using community-based small-scale mining in a developing country like Nigeria to move towards rural sustainable development.

Jan 1, 2011

By Wu Xueling

9K medium was used to isolate iron-oxidizing bacteria from 27 sump water samples collected from Dexing Cop-per Mine, Chengmen Mountain Mine and Yin Mountain Mine, Jiangxi Province, China. Lead acetate and silver nitrate were used to enrich metal-resistant iron-oxidizing bacteria from the above water samples. Isolate 16 was isolated from the sample taken at Dexing Copper Mine. Growth experiments indicated that when incubated under lead acetate (3,500 mg/L), isolate 16 still carried out ferrous ion oxidation, while isolate H1, a less resistant strain taken at Yin Mountain Mine, had a tolerance level of only 400 mg/L. When assayed with other metals, i.e., Ag+ (240 mg/L), Hg2+ (0.9 mg/L), Cu2+ (32,000 mg/L) and Mg2+ (22,500 mg/L), isolate 16 still carried out ferrous ion oxidation while, on the other hand, isolate H1 exhibited much lower tolerance levels, i.e., Ag+ (60 mg/L), Hg2+ (0.1 mg/L), Cu2+ (19,000 mg/L) and Mg2+ (13,500 mg/L). Based on 16S rDNA sequence data, isolate 16 and H1 were both identified as Acidithiobacillus ferrooxidans.

Jan 1, 2007

By H. Walqui

The Empire concentrator was built in four stages, with the latest stage accounting for 50% of the overall plant capacity. Over the past 5 years, the average throughput of the three grinding lines has decreased by 50 LTPH (15%) without significant changes in ore characteristics and despite the addition of secondary grinding capacity to supplement the existing pebble mills that are the constraint of the grinding circuit. This paper discusses the different areas under study that are aimed at optimizing grinding circuit utilization which includes improving system logic, pebble crushing operation and pebble mills operation.

Jan 1, 2009

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006