Search Documents

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By Michael Feroz, Marcus Jensen, James E. Lindell

The Southern Nevada Water Authority (SNWA) operates two water-intakes in Lake Mead, located 20 miles east of Las Vegas, Nevada. Severe drought has caused decline in lake level by 85 feet since 2000 and future declines are expected. SNWA will construct a third deep-water intake to ensure existing water system capacity. This paper describes expected construction challenges for the new project that consists of: an intake structure and tunnel beneath the lake, pumping station, pipeline to connect existing treatment facility, and interconnecting underground adits. The project will be completed in the year 2012 for total estimated cost of approximately $600 million.

Jan 1, 2007

Ground falls (roof and rib) have historically been responsible for nearly 50% of all fatalities in bituminous underground coal mines. In recent years, the number of some annual ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, the twin disasters at Crandall Canyon in 2007, in which nine miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990s, these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents since 2005. Progress has also been made in pillar recovery, where there has been just one fatal incident since 2005. On the other hand, more than 300 miners continue to be injured each year by rock falling from between supports and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities available technologies such as roof screen, rib bolting and inside control roof bolters could reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety.

Jan 1, 2011

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011

By R. L. Grayson

Based on the relationships between severity measure vs. productivity and other factors, this paper presents a comprehensive analysis of US underground coal mine injuries in 1996 by mine size. From the 1996 data, it was concluded that, generally, the larger the mine, the more productive it is (in tons per employee-hour) but the more severe is its injury experience (r = 0.65). However, within very large, large and medium mines, the more productive the mine, the less severe is its injury experience (r = -0.43, - 0.36 and -0.26, respectively). For small and very small mines, a deeply nested analysis would be required to understand relationships. Other interesting relationships and comparisons are presented.

Jan 1, 2002

By Arthur Darby

The city of Kuala Lumpur was founded in 1857 by miners seeking tin near the confluence of the Klang and Gombak rivers. The rapid development of the city and surrounding area since independence has led to more rapid runoff during rainstorms and to gradual canalisation of the rivers with some restricted sections. The outcome has been more frequent and more severe floods (Abdullah 2006). At the same time the centre of Kuala Lumpur has become a modern inter-national city with tall office buildings, hotels, and shopping centres connected by a network of wide roads and commuter rail systems. With these the cost of dislocation during floods has risen as has the cost of making good damage afterwards. The Government of Malaysia considered these consequences unacceptable and sought ideas from the private sector for a solution. Potential solutions consisted of variations on the themes of bypassing the city centre with a flood relief tunnel or of providing off channel storage or a combination of both. Since under Malaysian law a tunnel cannot be constructed under private property unless this is first purchased or agreement reached with the owner, it was necessary for most of the tunnel alignment to run below existing heavily congested roads. After considering these facts Gamuda Berhad and MMC Berhad, two leading Malaysian development and construction companies, decided to propose to Government an innovative solution in which the tunnel would be used to carry road traffic except during floods.

Jan 1, 2008

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay, Cicek Sena, Zhao Haochen

"Analysis of Longwall Pillar Stability (ALPS) and Analysis of Retreat Mine Pillar Stability (ARMPS) treat the pillar as a passive structure that is designed to carry overburden dead-weight. This dead-weight is calculated by simple rules based on the geometry of the mining, such as “tributary area theory,” “pressure arch theory,” and “abutment angle theory.” Although the pressure arch loading approach indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology of the overburden in load calculations. The relationship between successful pillar layouts and overburden geology can be incorporated into the load calculation by using the Ground Response Curve (GRC) approach.This paper introduces the GRC modeling methodology to investigate the effect of overburden geology and excavation geometry on load transfer mechanisms using seven field measurement case studies from four U.S. mines. It was also shown that the modeling methodology used to derive GRC in this study approximates mining-induced stresses and deformations within 5% of the values measured in the field.INTRODUCTIONFrith and Reed (2017) stated that current state-of-the-art pillar design methods ignore the overburden mechanics and use estimated dead-weight of overburden to compute pillar sizes. In the United States and around the world, overburden loading is typically estimated by simple geometric rules, generally with the tributary area theory (TAT). The specific overburden mechanics, structural competence of the overburden strata, geology, in situ stresses, and overburden/pillar interactions are typically ignored. However, these important mechanical responses affect the stability of the mine pillars and openings; therefore, they also affect the safety of the mine workers.Research conducted by the National Institute for Occupational Safety and Health (NIOSH) after the Crandall Canyon mine disaster (Esterhuizen, Mark, and Murphy, 2010) showed that small panel width-to-depth ratios and stiff-strong overburden result in a reduction of the observed pillar loads, much smaller than the TAT estimate. In fact, as a response to the Crandall Canyon disaster, Mark (2010) implemented a pressure arch loading approach into the latest ARMPS program to recognize the inherently greater stability of narrow panels at depth. The pressure arch approach is a first logical step to introducing non-tributary area loading into the practical ARMPS program. Although the pressure arch loading indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology and mechanical response of overburden in the load calculations."

Jan 1, 2019

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023

Beneath some of New York?s most iconic buildings ? The Met Life Building, the Helmsley Building, the Waldorf Astoria ? crews are busily at work on the Metropolitan Transportation Authority?s long-awaited East Side Access (ESA) project. In fact, it is 14 floors beneath the famed Grand Central Station where one of the centerpieces of the project, the new Long Island Railroad (LIRR) station terminal, is being blasted and carved into shape. When completed in 2016, the $7.3-billion ESA project will increase LIRR?s capacity into Manhattan and significantly relieve congestion at Penn Station. Currently, 37 LIRR trains per rush hour roll into the crowded Penn Station where many riders must then transfer to subway trains to complete their commute. When completed, the ESA tunnels will bring an estimated 160,000 riders directly to Grand Central Station, saving those riders 30 to 40 minutes. Studies have found that more people work within walking distance of Grand Central than Penn Station. ?The benefits of the project are tremendous,? MTA Capital Construction President Michael Horodniceanu told more than 340 industry professionals attending the UCA of SME?s George A. Fox Conference in New York on Jan. 26. ?The ESA is the first expansion of the LIRR in 100 years. It will increase the East River tunnel capacity by 50 percent and will help support job growth around Grand Central.?

Jan 3, 2010

By Richard R. Klimpel

During the last 28 years, I have had the very challenging and rewarding experience of working as an engineering professional in a large multinational company, both as a manager of engineers and engineering projects as well as an inventor and generator of new engineering processes and products. Due to the diversified geographic and tech¬nical nature of my employer's business, my responsibilities have taken me all over the world. This has included interactions with people in different industries including minerals, coal, chemicals, petroleum, pulp and paper, agriculture and pharmaceuticals. As diverse as my experience may seem, it has always amazed me how common the basic underlying technology and economic trends are that shape the working environment that any given engineer in any given geographic loca¬tion will experience. I would like to discuss the industrial evolution from micro to macro engineering. One of the basic truths behind how industry must and will operate is "change," including: • the creation of conditions for change, • the anticipation of change, • the resistance to change, • the rewards that being part of a change can bring and • the destruction that change can bring to the unprepared. This fact was well stated by Heractitus around 500 BC.: "There is nothing permanent except change." This simple truth has been valid since the dawn of time and, if anything, is accelerating in nature every decade.

Jan 1, 1993

By Micah Nehring, MEHMET KIZIL, Farzad Sotoudeh, Amin Mousavi, PETER KNIGHTS

Production scheduling in underground mines is one of the most important and complex processes in maximising the economic value of an operation over the life of the mine. Due to increasing energy, transportation, processing and smelting costs and reducing water availability, the extraction of ore deposits through underground operations has become more expensive and challenging. A potential productive and efficient solution to mitigate these issues is to integrate pre-concentration systems into the existing mining system to increase ore grades through a preliminary process of rejecting some waste before sending the ore to the energy intensive mineral processing plant. Further benefit of such systems includes the utilisation of the waste and low-grade material in backfilling of open stopes to reduce the transportation costs and surface environmental impact such as reduction of CO2 emissions and waste transportation. The objective of this paper is to present a new mathematical model to optimise the production schedule of underground metalliferous mining operations in the presence of a pre-concentration system. The proposed model optimises the production schedule and sequencing of stopes within a sublevel stoping operation. The results of this study illustrate the potential economic benefits of using a pre-concentration system prior to a mineral processing operation as a result of increased net present value.

Nov 16, 2023

By Vladimir Admek, Paul W. Jeran, Michael A. Trevits

It has' been found that lithological conditions over the Pittsburgh Coal bed cause the subsidence coefficient to vary within the area of the subsidence trough. This precludes the use of European developed predictive models, which are based upon a constant subsidence coefficient. Regression analysis of the distribution of subsidence coefficients from 11 Bureau of Mines, U.S. Department of the Interior, longwall panel studies on the location relative to the edge of the panel has yielded a third degree polynomial equation. This equation has been incorporated into a BASIC computer program for use on a personal computer that allows users with no previous knowledge of the theory of subsidence to predict vertical movements over typical longwall panels in the Northern Appa1achian Coal Basin.

Jan 1, 1986

By B. Ballard

Engineers at a West Virginia coal preparation plant owned by one of the nation's largest coal producers sought a fire suppression system for the plant's MCC and cable spreading rooms. Officials considered the traditional options of water-based sprinklers, dry chemical, and clean agent systems; however, each of those options presented challenges. Sprinklers can damage electrical equipment, proper delivery of the agent and adequate coverage/protection can be an issue with dry chemical systems, and clean agent systems require room integrity. An alternative to traditional systems was discovered in the Victaulic Vortex Fire Suppression System. The first hybrid inert gas/water mist system (FM 5580), Vortex adequately addressed these concerns. The system, which deploys a high-velocity, low-pressure mixture of water and nitrogen, is not damaging to electrical equipment and extinguishes fires in open, ventilated areas. This is one of the first installations of the Vortex system in a prep plant, and is a compelling example of how new technology can overcome the challenges of traditional technologies. The paper will detail plant specs, situation, and system evaluation, selection, and configuration.

Feb 23, 2014

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By C. Wen

In Huoqiu region of Anhui Province, Fe2O3 occurs mainly in the form of specularite. Besides quartz, the gangue minerals include iron-bearing silicates such as chlorite and sericite which account for about 10% of the total gangue. The separation effect of conventional collectors is poor in the flotation of the minerals, that is, the average grade of iron concentrates is only 60-62%. Using the developed amphoteric collector can successfully realize not only the separation of specularite from various gangue minerals with results of iron concentrate grade above 65% and iron recovery of above 80% but also low temperature flotation at 15°C.

Jan 1, 2012

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By R. Hipsley, D. Arbonies, P. Dobak

South Arturo is a “Carlin-type”, breccia-hosted, oxide gold deposit located at the north end of the Carlin Trend. The discovery hole was drilled in July 2005 from mine dumps 1,000 feet south of the Dee open pit. Discovery hole (BD-72) encountered a cumulative 245 feet @ 0.056 opt Au beneath 850 feet of post mineral Tertiary Carlin Formation. Oxidation extends to depths greater than 2,000 feet in the deposit area. The deposit is presently in definition drilling stage with approximately 190,000 feet of drilling completed to date. A resource estimate is in progress. This paper will focus on the discovery and descriptive characteristics of the mineralization.

Jan 1, 2007