Search Documents

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

By R. A. Jankowski

The U.S. Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces of up to 12.2 m in length. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain setback distance, operator positioning, and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels on the order of 0.5 to 1.2 mg/m3 were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust control system for extracting deep cuts up to 12.2 m in length. The impact on methane was not evaluated.

Feb 24, 1997

By R. Hedin, M. Dunn

The Pennsylvania Department of Environmental Protection (US EPA 319 program) provided funding to aid a public-private effort in the installation of an environmentally-friendly system to treat abandoned mine drainage at Jennings Environmental Education Center (Pennsylvania Department of Conservation and Natural Resources). Through this cooperative effort among state and federal agencies, mining, excavation, and environmental companies, college and home school students, Girl Scouts, and volunteers, a successful multi-component passive system, readily accessible for upgrades and public education/research activities, was built. 90 people were directly involved in construction of this award-winning system and about 1000 people annually benefit from the educational opportunities.

Jan 1, 2002

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By M. Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes that the particles are initially nonporous, have a constant mass prior to fragmentation and travel at a constant velocity throughout the reaction chamber. The model requires the specification of the following five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with the experimental data collected in a laboratory furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2008

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process 1.2x0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm.

Jan 1, 2002

By A. C. T. Bigg, Y. Kocak, N. K. Bodur

The Gumuskoy silver mine, owned by the Etibank, in the province of Kutahya, Turkey, has been operating since 1987 with primary, secondary and tertiary crushers, and two parallel single stage ball mill circuits. Continuing problems with crushing and feeding of the ore to the ball mills, because of the moisture retaining and sticky nature of the ore, prompted an investigation into the possibility of converting the grinding circuit to an autogenous or semiautogenous grinding circuit. This would remove the bottleneck associated with the secondary and tertiary crushing. At the same time the target feedrate is to be raised from 140 t/h to 175 t/h. This paper demonstrates the response of five ore types, and blends of ore types in an onsite pilot plant test program, and also suggests how the variations can be handled in a SAG mill/ball mill circuit incorporating just one of the present ball mills.

Jan 1, 2000

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By Jai Ghosh, Aprad E. Torma, Roger Guay

The catalytic effect of ferrous ion in the industrial biohydrometallurgical heap and dump leaching processes is explained. During the bacterial leaching of metal sulfides, ferric ion will partly be hydrolyzed and a variety of sols, gels, amorphous and/ or crystalline mono- and polynuc- lear hydroxo- and sulfato complex species formed, especially by olation and aggregation reactions. There are many problems associated with these iron precipitates especially in the purification of leach solutions. The present study will discuss the iron precipitation reactions; gives kinetic and thermodynamic evaluations of the effect of temperature on pyrite and ferrous iron oxidation; and reports on the tolerance of heavy metal ion concentrations by Thiobacillus ferrooxidans.

Jan 1, 1989

By N. Ahmed

The collection of hydrophobic particles in the froth phase in flotation has been studied. A continuous flotation cell was developed, in which the froth phase could be isolated from the pulp zone. Hematite particles, d80 = 87 µm, were floated in the pulp, using a conventional oleate collector, while glass spheres of similar diameter, d80 = 82 µm, were introduced in wash water added to the froth. Four samples of glass spheres, with contact angles between 0 and 82 degrees, were used. The results indicate that the efficiency of collection of the hydrophobic particles in the froth can be very high. The process is strongly influenced by the hydrophobicity of the particles and the surface area available for attachment in the froth. Recommendations for the flotation of particles in the froth phase are made, especially regarding the desirable hydrophobicity as reflected in the contact angle, the froth depth, the solids concentration in the feed to the froth, the air rate and the wash water rate.

Jan 1, 2001

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By W. L. Zhong

Probability function integration method is one of the influence function method. It is a widely accepted method in many mining districts in China and Poland mainly because its theory and formulae can well-represent the surface subsidence basins due to longwall mining of flat or near-flat seams. This paper introduces the basic theory of the probability function integration method and determines its 4 basic parameters by analyzing the measured subsidence profiles in eight longwall panels in Northern Appalachian Coal field. It also discusses the two methods for determining the 4 parameters. Finally the acquired parameters are used to predict the subsidence and deformation of the houses for damage assessment. Comparisons are made between the measured and the predicted subsidence. Probability Function Integration Method The probability function integration method for predicting surface movements and deformations is widely used in China and Poland. The governing equation of the method contains five parameters: subsidence factor, a, offset of inflection point, d, tangent of the major influence angle, tan fl, horizontal movement constant, b, and major dispersion angle e (e = 90. for flat seams). Its applicable range iis much larger including seams less than 30' from the horizontal, critical and noncritical mining and soft to hard overburden.

Jan 1, 1986

By I. Tsolas

This paper presents the use of non-parametric approach (i.e., data envelopment analysis, DEA) for the development of environmental sustainability indicators in mineral processing using environmental, economic and/or integrated indicators (i.e., indicators that interrelate two dimensions of sustainability). A case study based on real publicly available data is presented to illustrate how the proposed approach can be implemented in practice. The merit of this approach, which is based on the productive efficiency framework, is that it provides environmental sustainability indicators that can be used internally for benchmarking purposes and externally for sustainability reporting.

Jan 1, 2008

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007