Search Documents

By J. A. C. Diering

The simulation of mining in faulted ground was recently described by Crouch. His method is extended here to enable a wide range of non-homogeneous mining problems to be modelled. Essentially, the boundary conditions at geological interfaces are incorporated into the overall iterative solution, which is necessary if faults and joints are to be modelled realistically. Two examples are given to demonstrate the method: the mining of coal a seam below a thick dolerite sill, and the mining of a flat reef in close proximity to a vertical fault where hangingwall and footwall rocks have different properties.

Jan 1, 1980

By L. Dison

This technical note is issued in two parts as follows. Part I, which appeared in the January issue of this Journal, after a brief introduction, discusses the value of patents and the law of patents, including patent applications and the exploitation of inventions. This is followed by some comments for the benefit of would-be inventors and potential users of patents. Part I focuses on the mining industry and then discusses views on patents that were quoted in Part I. The last section makes recommendations as to how inventors and users (including mining authorities) should handle patents.

Jan 1, 1992

By C. E. Feather, G. M. Koen

The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E. FEATHER B.Se. Hons. (Cape Town)* and G. M. KOEN D.Se. (Pretoria)* A description is given of the nature and occurrence of gold at various stages in the process of its recovery from Witwatersrand and related ores. Electron microprobe investigations show that the surface of gold grains in the ore is already coated. During metallurgical processing, further coatings, mainly hydrated iron oxides, accumulate on the grains. Theories are advanced for the formation of these coatings, and the adverse effects on metallurgical operations are discussed.

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

Contribution by G. Narsimhan It was with much pleasure that I went through D.F. Malan's excellent paper. The following explanatory and critical note has been the result of my deep study of the paper. Although by qualifications and experience I have been a chemical engineer, involved over four decades with problems in the modeling and simulation of transport-limited (heat and mass) chemical reactions in multi-phase systems, I have of and on interested myself in challenging problems in extractive metallurgy. This is the first time I have veered of to continuum mechanics, at the age of 71! Author's reply. I thank Professor Narsimhan for his extensive contribution to the paper. It provided me with the stimulus to derive an extended model. However, there are some inaccuracies in his arguments that need further discussion. Professor Narsimhan's main concern is that there is not a good enough fit between the derived viscoelastic Kelvin model and the experimental data supplied by Güler1 (see Figure l1 on page 218 of my paper). I will therefore explain the choice of a viscoelastic model in more detail and also make specific comments on the arguments given in his contribution.

Jan 1, 1996

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

By D. D. Howat, J. van der Colf

Selected members of the slag system were reduced in graphite crucibles in an argon atmosphere, and the physicochemical properties of the reduced derivatives of the slags were determined in inert crucibles. It was found that slags having magnesium aluminium titanate as the primary phase before reduction underwent an increase in liquidus temperature, accompanied by a change in the primary phase. No analogous behaviour could be detected for the slags having perovskite as the initial primary crystallization product. In most instances, the viscosity of the melt passed through an initial minimum, followed by an increase as the reduction time was extended. Increased MgO/CaO ratio. basicity, titania content, and reduction temperature all served to accelerate thickening. During reduction, the electrical conductivity of the slags tended to rise relative to the value for the unreduced melt.

Jan 1, 1979

By H. A. D. Kirsten

Mining-induced seismicity is usually evaluated in terms of continuum elastic analyses, and is quantified in terms of energy release rate as state parameter and excess shear stress along particular features on which failure may be induced. Although both of these quantities are representative measures of potential seismic activity, elastic analyses do not enable the associated stresses and displacements in the rock in which failure occurs to be evaluated reliably. The paper compares the effect of depth, span, support stf1Jhess, field stress ratio, and discontinuity strength on mining induced seismicity determined from elastic analyses and from analyses in which discontinuities in the rock are allowed to fall. It is, accordingly, shown that the incidence and magnitudes of potential seismic events and the net excess shear as representative state parameter cannot be determined reliably from elastic analyses that do not account for the failure of ubiquitous discontinuities. The magnitudes of seismic events in rock in which ubiquitous discontinuities are allowed to fail are very considerably overestimated in elastic analyses. The extent of the seismic source region and the associated seismicity do not increase with depth, which, together with the improved containment of the concomitant rockburst damage by backfill is reassuring for mining at greater depth in future. For conventional support, the magnitude of potential seismicity increases for an increase in span in elastic rock, but remains unaffected in non-elastic rock. For backfill, the magnitude of potential sesmicity decreases substantially in elastic and non-elastic rock for an increase in span. Increases infield stress ratio very significantly reduce potential seismicity irrespective if the type if analysis, but effect the distribution if potential seismic events very differently in elastic and non-elastic rock.

Jan 1, 1994

By deur R. R. Mears

The expected curtailment of activities within the gold-mining industry by the closure of the more marginal mines, and the shortening of the life of the industry as a whole as a result of rising costs and/or an uncertain gold price, are factors that are bound to harm the South African economy in a number of ways. The industry has no option but to regard the gold price, which is determined on the world market, as a given quantity. The remaining ore reserves al tend to be of a lower grade and/or to be found at greater depth. Therefore tighter control of working costs would seem to be almost the only option open to the industry. Working costs can be divided into two broad categories: costs emanating from the environmental characteristics of the orebody, and costs emanating from the general inflationary environment in which the industry has to purchase its inputs. Working costs stemming from the physical environment also fall into two categories: those relating to the grade of the orebody, and those resulting from working at increasing depth and temperature, together with the need to pump increasing quantities of water. The industry is both capital- and labour-intensive in absolute terms, since it requires large inputs of labour as well as of capital. It is limited in its scope to adjust its production function by becoming more labour- or more capital intensive, and is dependent on a large labour force, which cannot easily be replaced by capital inputs. On the other hand, large amounts of capital are required for investment in shafts, development, machinery, and equipment. Since the early seventies, the working costs of the South African gold-mining industry have increased at an annual rate that was significantly higher than the general rate of inflation. This rapid rise in working costs has caused some mines to find themselves in a difficult profit position. At times, the gold-mining industry has even been compelled to restructure its cost/revenue relationship rather fundamentally by revising the grade of ore worked sharply upwards or downwards, as the case may be. The rise in the gold price since 1972 has made it possible for the industry to introduce significant changes in its Black wage policy. The main aim was to increase the permanency of the Black labour force and to encourage local Black workers to join the industry. At the same time, significant increases were also experienced in the cost of machinery and stores, as well as of capital, mainly as a result of inflation. In the study on which this paper is based, the author attempted to measure the influence of environmental factors on working costs, using the physical consumption of electricity as a criterion for measurement. He found that the usefulness of this criterion in relation to factors such as depth, temperature, and water quantities pumped was invariably more than neutralized by the effects of greater productivity and economies of scale. The effects of these environmental factors on the working costs of the industry could therefore not be determined to any degree of accuracy. It seems that good progress is being made with the development of capital-intensive forms of technology aimed at coping with rapidly rising working costs and other effects of increasing depth. Techniques are also being developed to improve rock-cutting procedures and to eliminate the use of explosives in order to introduce a continuous mining process. On the whole, the gold-mining industry seems to be more sensitive to general inflationary pressures than to the cost effects that are associated with depth, temperature, and water quantities pumped. Greater control is possible over physical environmental factors such as the grade of ore mined, temperature, rate and nature of development of a mine, and adaptation of the daily working cycle to a continuous mining process. Wolfe and others hold the view that the industry will lose control over labour costs as a result of the 'sharp increase in wages and the growth of Black trade unions. However, the use of more capital-intensive technology will allow the industry to reduce its labour force, and a smaller, better-trained, and more permanent labour force will enable the industry to cope with the increasingly difficult physical environment and higher wages.

Jan 1, 1987

By R. H. C. Andrew

With the advent in recent years qf mechanization in deep-level gold and platinum mines, large quantities of rubber was are being used on both production and support vehicles. Conditions in these types of mines are extremely harsh and, as a result, we performance is significantly lower than in other types of mining such as open-cast base metal mining, where more favourable conditions prevail. Various options are available to the user to reduce tyre costs, including the use of retreads, the filing of tyres, and the repair of damaged tyres. While these methods may be generally successful in open-cast conditions, their use in deep-level mining needs to be carefully evaluated for each particular set of conditions. A basic requirement for any evaluation of we costs is the availability of reliable data on tyre performance and, for this reason, it is essential that proper tyre records are maintained This paper reviews the performance of tyres in deep-level gold and platinum mines in Johannesburg Consolidated Investment Company, Limited (JCI) over a period of about 8 years, and shows how the costs of retreading and tyre filing can be evaluated in practice. It also discusses the cost implications of repairing damaged tyres.

Jan 1, 1994

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By NONEn NA

1. Book reviews . Rudiments of mining practice, oy C.E. Gregory.Clausthal-Zellerfeld (West Germany), Trans Tech Publications.OS$24.Reviewer: A.N. BrownProfessor Gregory has had a wide experience of hardrockmetalliferous mining throughout the world, beinga well-known academic who has taught at many universitiesin the Western World. His basic training was obtainedin his native land of Australia. In this publication he identified the need for a basic, simple book on miningpractice to provide new students of mining with a backgroundto their studies. He also designed the book to providea background to persons operating on the fringesof the industry such as students of economics and journalists.The text extends to only some 120 pages, and containsa sufficient number of monochrome sketches, diagrams,and photographs. It is written in a straight-forward, easyto-read style. The book contains an index and elementarytable of conversion from imperial to SI (metric) units,and there is also a glossary of mining terms that mostreaders would find useful.The author has succeeded in keeping the contentssimple, as indicated by the title. However, after each chapter, there are references to further recommendedreading. The book could be useful in the South African context, although the coverage of coal and opencast mining operations is slender.

Jan 1, 1987

By J. Meintjest

As you pointed out, furnace power factor (and consequently transformer MVA rating) depends upon the inductive reactance, and so it is desirable to design for the lowest possible value of this parameter. The further introduction on the primary side of the transformer of capacitors, whether in shunt or in series, increases the network power factor but does not alter the furnace power factor; that is, the phase angle between electrode to- hearth voltage and current remains unchanged. Corrigenda The following amendments should be made to the article entitled 'Coal-preparation routes for maximum coal recovery', which was published in the August issue (vol. 80, no. 8) of this Journal:

Jan 1, 1980

By N. O. Lotter

Evaluation errors and value frequency distribution models of the gold ore bodies in the Witwatersrand and Free State systems are reviewed. It is found that the low-grade sections of the data are prone to the largest evaluation errors, and that an understanding of the shape of the value frequency distribution is essential to the calculation of mean grade. The evaluation of a mineral process for a particular ore requires attention to mil-feed sampling, sample processing, and monitoring. In particular, the calculation of a representative mass of mill-feed sample (Ms) should take account of size-by-size value variance. Alternative Ms models are discussed.

Jan 1, 1995

By M. Klapwijk

Ancient Metallurgy - In addition to the preceding three papers, the following three contributions were received for publication 1. An analysis of Bantu-made iron implements from the Letaba district M. KLAPWIJK INTRODUCTION It has often been stated that it is hardly possible in South Africa to classify Bantumade iron hoes according to their places of origin and manufacture. It is well known that these hoes were used for barter, and as currency in the purchase of livestock or the payment of lobolo, although reports of the value of the hoes differ widely. The difficulty in their classification has arisen from their distribution over a very wide area.

Jan 1, 1974

This paper describes an interactive personal computer program, ENVIRON, which simulates cooling and ventilating systems on gold mines. An example of the practical application of the program is given and proposed future developments are discussed. The program consists of two main modules, HEATFLOW and VENT- FLOW. HEATFLOW calculates the heat loads and the effect of air coolers, while VENTFLOW estimates the air flow distribution. As the calculation of the heat loads requires a knowledge of the air flow and vice versa, the two modules are run iteratively until the solution converges. The program is written in Pascal and runs on any IBM-compatible personal computer.

Jan 1, 1987

By N. B. Strydom

I have read with interest all the papers dealing with heat transfer and the setting of heat stress limits that have appeared during the past two decades. Scientifically speaking, most of them can be rated as being of a high standard, and some of them have been acclaimed internationally as masterpieces of logical and calculated reasoning. Weathering of ore minerals A short course on 'The Weathering of Ore Minerals and the Textural Evaluation of Base Metal Gossans' is to be given by Dr I.M. Reynolds in Grahamstown from 4th to 6th October, 1982.

Jan 1, 1982

By H. Scott-Russell

Ladies and Gentlemen. It is my great pleasure on behalf of The South African Institute of Mining and Metallurgy and The Geological Society of South Africa to welcome you to the 15th CMMI Congress and to Southern Africa. It is a great honour to be hosting this event and we have been looking forward to it for a long time. I am sure the technical discussions and visits will be of great value, and I am confident you will return with pleasant memories of places and people in South Africa and neighbouring countries. The theme of this Congress, Resources and Technology', is appropriate for discussions on the ways and means of going forward in the minerals industry to create the employment and wealth so sorely needed in this region. The technical programme will give mineral industry professionals from different parts of the world the opportunity to share experience and expertise for the purpose of making operations more productive, safer and environmentally acceptable to the world at large. Delegates will be exposed to current technical developments by means of 133 papers prepared for the congress: 30 on geological subjects, 45 on mining, 29 on extractive metallurgy, and 29 in the field of metals technology.

Jan 1, 1994

By Zdenek Kunicky

Kovohute Pribram is a plant recycling lead wastes, lead acid batteries in particular. Relevant new recycling technologies are being gradually developed. Outdated technology of smelting lead plates has been replaced by a new technology based on processing of entire batteries in a blast furnace according to the process developed by know-how of German Varta company. The classical Harris refining has been substituted by the oxygen refining. New technologies aimed at utilization of related wastes arising from refining lead bullion in Kovohute Pribram are being developed in house. At present, a new technology of utilization of spent battery acid for extracting zinc from various wastes has been developed. Zinc oxide dross from alkaline refining of lead bullion, during which residual zinc from the preceding vacuum de-zincing is removed as well as waste zinc galvanic sludges (a product of neutralizing precipitation of metals from industrial wastewaters with lime) were treated. In this study, the new developed technology yielding basic zinc carbonate - a valuable raw material for zinc electrowinning, is described together with the first experience of applying the developed method to processing zinc wastes on a pilot scale. Most of the equipment used in the past to regenerate alkali solutions originating from Harris refinery was utilized in the practical realization of this new technology.

Jan 1, 2008

By D. G. Keefe, I. C. Robinson

In this paper the authors present their views on the actual and potential role of commodity analysis in mining industry. Owing to the dominant influence of the economy on all commodity markets, it is essential that individual commodities are studied not only in depth but within the broader context of economic influences. A commodity unit, which monitors market developments in a wide range of commodities, is well placed to provide the broader perspective in the study of commodity markets. This paper describes some of the specific functions of such a unit. Some of the methods used for price forecasting are described, and the results of price forecasts by different forecasting methods are compared.

Jan 1, 1980