Search Documents

By R. R. M. Cousens, W. S. Garrett

Discussion: L. T. Campbell Pitt: When Mr Garrett and I discussed the design and construction of plugs and bulk head doors to resist great water pressures in mines about ten years ago, we visualized an emeregeny when there would be no time for site preparation. We could not however, anticipate a problem of such magnitude and urgency as the one described in the paper under discussion. The paper very clearly describes the flooding and the measures taken to save the mine. The complete flooding would have been a national disaster. The account of the combat between man and water reads like the account of a military operation. It was an endeavour which achieved success because there was a master plan, tenacity and, in fact, heroism. The paper is of necessity a long one. In my contribution I will mention some historical facts and factors that I believe have relevance to the flooding and the saving of the mine. It is of great satisfaction to me to have been one of the two initiators of a new approach to underground plug design and construction. The investigation was taken over by a Chamber of Mines Committee which combined our early work with further research and the resulting data had a significant bearing on the West Drie emergency plug designs. The final plug length was correctly based on the requirements to obviate leakage. A plug to have structural strength only would have been very much shorter but so ineffective as to have become a waste of labour, material, and in consequence, wasted the limited time available to prevent flooding of the whole mine. The figure of 75 lb per sq in. sheer stress provided a very ample margin, in my opinion, but under the very difficult site conditions and the limitations of plug material suitable for the very unusual construction, justified such a figure. There must have been considerable temptation to reduce the safety margin due to the urgency to complete and commission the plugs, but it is much to the credit of the directors of this operation that nothing less than a safe design was permitted. In about 1945 Blyvooruitzicht Gold Mining Company, which was then mining in to the West Driefontein area to assist in early development, decided to protect themselves from a possible inrush of water from the latter mine. A bulk head door was accordingly designed and installed on 2 level between 1945 and 1948 at 4,218 ft below surface. Since West Driefontein paid for it, Gold Fields consulting mechanical engineers collaborated with their colleagues of Rand Mines who completed their design after a few modifications were agreed. This door was never used to prevent an inrush into Blyvooruitzicht but the exercise was very useful to Gold Fields when the high pressure doors initially installed on 10 and 12 levels between Nos. 2 and 3 shafts to enable isolation of one section of the mine from another were designed. At that time the capacity of West Driefontein to cope with an inrush of water was comparatively small because the storage in stoped areas and the installed pump capacity were much less than in later years. These doors together with others of the same design were later moved to the lower levels served by sub vertical shafts. In addition, doors to prevent flood water entering the pump chambers on 18 level were installed at each end of that level, and designed for a head of 360 feet so that water would have to reach 16 level before the pumps were flooded. All these doors were called upon to hold water and it is reported that only a small plug in one of the doors and a 4 in. dia flanged pipe joint failed. The lesson is that in these cases the smallest details warrant as much attention as the major ones. That these were the only equipment failures when so much depended on equipment, is very much to the credit of design engineers, both of the Gold Fields head office and companies who supplied both mechanical and electrical equipment. Until I had read the paper I wondered why the policy of isolation by bulk head doors was not continued as the development moved eastward towards the Bank Compartment and particularly when it pierced the Bank dyke. The reasons have been given in the paper. It was unreasonable to expect provisions to be made to counter the remote contingency that the large installed pumping capacity and mine capacity to store water would be exceeded during a peak inrush. When pumps were being considered for West Driefontein, it was decided that the Gold Fields standard underground main pumps at that time of 1 million gallons per 24 hours would be too small. Three alternatives were considered. 1. Very large units that would require underground sub assembly and dismantling of both pump and motor. 2. The largest pump and motor that could be conveyed as a complete pump or motor from surface to the pump chamber. 3. Pumps of higher speed to reduce dimensions and weight. It was decided to adopt alternate 2 because of avoidance of transporting pumps in parts and assembling underground. Alternative 3 was not favoured because high speeds would have introduced problems of more exact rotor balancing. I believe the decision was correct and in the crisis enabled comparative easy transport of pumps and motors to surface for overhaul and, if required, transfer to other pump stations. The standard pump thus became a 10 stage 1,500 rpm pump with a capacity of approximately 2 million gallons per 24 hours against a static head that varied

Jan 3, 1969

By J. W. van der Merwe, K. G. Moloko

Furnace wall tubes from 600 MW subcritical boilers at three coal-fired power stations were sampled and the fireside deposits examined to determine the mechanism of fireside corrosion. This involved an indepth investigation into the morphology and composition of the fireside deposits and the conditions of the furnace that enable this type of attack. SEM-EDS analysis revealed high concentrations of oxygen, iron, and sulphur, QEMSCAN and XRD analyses identified the presence of Fe3O4, Fe2O3, FeS, and FeS2. Differential thermal analysis showed thermal activities at temperatures of 500–600°C, 900–1100°C, and 1100–1250°C, which are associated, respectively, with FeS2 oxidation to FeS and Fe2O3, at 475–525°C, formation of aluminosilicates at 925–1100°C, and melting of FeS around 1190°C. The absence of sodium and potassium eliminates the contribution of molten alkali sulphates to the corrosion. The consistent coexistence of iron sulphide and iron oxide is indicative of the substoichiometric conditions in the furnace, while the detection of pyrite suggests that the coal is not completely combusted, which points to a poor combustion process. These observations were affirmed by gas analysis at one of the stations, where very high levels of carbon monoxide were measured at the furnace wall (≥ 14 000 ppm) and furnace exit (≥ 3500 ppm). The high CO concentrations are indicative of limited combustion caused by limited O2. These reducing conditions promote the formation of FeS-rich deposit, which is the corrosive species responsible for degradation.

Jun 1, 2021

By A. Della Rocca, P. Jonker, B. Henning

Successful prediction of the collection efficiency of cyclone separators is a necessary step in cyclone design and verification. Aside from standard empirical relations, CFD modelling is widely adopted to supplement the design of cyclone units in relation to the desired separation performance. Nevertheless, effective adoption of numerical modelling is sometimes prevented by large modelling errors, especially for small size particles which are more subject to turbulence effects than larger particle classes. In the past, this motivated the adoption of more refined turbulence modelling approaches, such as large-eddy simulations. These approaches provide greater insight into time dependent behaviour, while leading to larger computational cost with respect to more standard approaches. In this paper, an effective Eulerian-Lagrangian Reynolds-averaged Navier-Stokes (RANS) approach is investigated, which is able to predict the complete separation efficiency curve with satisfactory accuracy, without requiring prohibitively long computational times. An assessment of the proposed approach is carried out against experimental data from large laboratory scale cyclones, in the form of mean and fluctuating velocity profiles from LDA measurements (Hoekstra, 2000), as well as with respect to the experimental separation curve (Zhao, 2005). The final application to a full-scale industrial cyclone unit is then carried out with the aim of tuning the cyclone design to the separation efficiency curve as required by downstream processes. Keywords: Cyclones, separation, CFD, RANS, RSM, Lagrangian

Jan 1, 2020

By A. Mainza, I. Govender, Elbasher M. E. Ahmed

A mechanistic description of axial segregation in rotating drum flows remains an open question. Consequently, optimal mixing of grinding balls and rocks for efficient breakage, maximum production of fines, and slurry transport is seldom achieved. Experimental and numerical studies of granular mixtures in rotating drums identify alternating axial bands that eventually coarsen in the long-term limit. Most models of axial segregation are limited to binary mixtures and cannot always predict the logarithmic coarsening effects observed experimentally. A key missing factor is a robust description of the axial free surface profile that is valid across a wide range of flow regimes. We present a practical model of the axial free surface profile by linking it to readily-derived geometric features of the cross-sectional S-shaped free surface profile. A parametric study shows good agreement with experimental measurements reported in the literature and heuristically valid trends.

May 1, 2021

By D. N. Esfahani, K. Khazen, M. Mohammadi

Electrowinning is one of the nickel recovery processes from solutions obtained from the leaching of nickel sources. Every year significant amounts of nickel products are used in various industrial processes and daily life, such as catalysts or batteries, which are a valuable source of nickel for recovery. Nickel purity is also very important in the electrowinning process, because the amount of impurities in nickel such as sulphur, if greater than 100 ppm, make it unsuitable for use in catalysts and plating. Because sulfur is intrinsic to the sulphate electrowinning system, we needed to investigate parameters that can affect the quality and purity of nickel. In this regard, experiments were performed in static and circulating electrowinning processes. A monitoring and circulation system was designed and built to measure voltage, current and temperature as well as to circulate the solution in the system at a specified rate. It was then observed that nickel ion concentration, pH, using the circulation system and additives, were factors affecting the purity and quality of nickel, and in the best case the amount of sulphur in nickel was below 100 ppm. Keywords: Nickel, electrowinning, sulphur impurity

Jan 1, 2020

By L. S. Bicalho, W. J. Rodrigues, P. M. A. Rollo, P. R. G. Brandão, W. C. da Silva

Quadrilátero Ferrífero is an important mineral province located in Minas Gerais state, responsible for a substantial amount of iron production in Brazil. Among the concentration methods for iron ore practised by the mining companies in this region, the most important is the reverse cationic flotation. Dolomite iron formations, with the presence of hematite, quartz and dolomite, occur in several areas of mining and, with the deepening of the deposits, this type of ore, with low iron content and more complex mineralogy occurs frequently. Carbonaceous minerals, mainly dolomite, present a technological challenge for the concentration of iron ore by flotation. In the present study, the concentration of iron ore with 6% of dolomite content was evaluated. Bench flotation trials indicated that conventional iron ore flotation is not selective to float dolomite, thus compromising the iron content in the final concentrate. Alternative flotation routes were evaluated, and a selective condition was reached to float both quartz and dolomite using the combination of the cationic collector Flotigam 16424 with an anionic collector Flotinor 16551. It was demonstrated that the flotation of dolomite was improved with the combined use of both collectors in the cleaner stage, and by a previous quartz flotation in the rougher stage. Zeta potential analysis indicated specific adsorption as the adsorption mechanism between Flotinor 16551 and dolomite, confirming the high selectivity observed in the bench flotation tests. Keywords: Flotation, iron ore, dolomite

Jan 1, 2020

By J. Bullón, A. Pérez

Some years ago, Ferroatlantica developed a new type of electrode known as the ELSA electrode. In this electrode there is a central graphite core that provides support, surrounded by an annulus of Søderberg paste that gets baked during operation. This technology has been implemented on several silicon furnaces around the world, and was reported on during the previous Infacon conference. In all electrodes, but particularly in the ELSA electrode, the quality and consistency of the paste are important for correct operation. As the type of paste varies between customers and between countries, Ferroatlantica has developed a quality control procedure for their customers of this technology. This procedure is geared to the point of view of the customer rather than the paste producer. The analysis is based on the desired flow pattern of the raw paste and on the desired mechanical and electrical properties of the baked paste, as experience has shown that these are the most important parameters to monitor in order to avoid having problems with the resulting electrodes. This paper discusses these methods of paste analysis in the light of complementary studies that have been done when there has been an electrode breakage in the different plants.

Jan 1, 2007

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By L. W. Helle

In this investigation, which was conducted at the Metallurgical Research Plant, Lulea, Sweden, a series of experiments were carried out using a water-model to simulate the gas rinsing of a ladle containing liquid metal. The factors examined include the effect of gas flowrate, the position of a porous plug or lance, the immersion depth of the lance, and the geometry of the bath at the time of complete mixing. Mixing times were recorded by conductivity measurements. The results showed that there is a threshold level for mixing above which no advantage is to be gained from an increase in the gas flowrate. It is suggested that the results can be applied to rinsing ladles in working situations, the levels being approximately 270 dm3/min for 40 t ladles and 780 dm3/min for 150 t heats. The optimum siting of the lance or porous plug is a position that is three-quarters of the internal radius from the centre of the ladle with the lance penetrating as deeply as possible into the ladle. The best design of liquid bath is that having a diameter-to-height ratio of I. An equation was developed for the calculation, by dimensional analysis, of the time required for mixing during gas rinsing, and a comparison of the calculated mixing times with the results from production trials shows a satisfactory agreement (with a correlation factor of 0,91). Thus, an equation is available for the calculation of the stirring time needed to completely mix the bath in production situations.

Jan 1, 1981

By G. P. O’Malley, A. N. Nikoloski

One of the most promising options for extraction of copper from low-grade chalcopyrite ores by heap leaching, however, chalcopyrite is refractory and suffers slow leaching kinetics and poor overall extraction due to formation of a passivation layer on the particles. The solution composition is believed to strongly affect the formation of this layer. This paper examines the effects of the major cationic species of Fe3+/2+, Mg2+, Cu2+, and Al3+ and the anionic SO42− species in acidic ferric sulfate media with a composition simulating recycle heap leach conditions. It was found that altering the sulfate, iron or aluminium concentration had significant effect on the copper extraction, the concentration of copper slightly influenced the extraction, and the amount of magnesium had no appreciable effect. Also, iron and aluminium caused a change in the sulfate concentration, and the sulfate ions had the greatest influence on the extraction of copper under recycle leach conditions

Jan 1, 2023

By SAIMM Journal

COLLOQUIUM ON COMMINUTION The Institute has arranged a colloquium on the above topic to be held on 13th March, 1973, at Kelvin House. The following papers will be presented: 'Peripheral Discharge Mill', by A. H. Mokken, Union Corporation Limited

Jan 1, 1974

By Z. Zitron, G. J. de Korte, D. W. Horsfall

This paper summarizes work carried out on the treatment of fine coal, nominally classified as minus 0,5 mm (wedge-wire screen), which is removed from the raw coal prior to the treatment of the plus 0,5 mm sizes. The minus 0,5 mm coal divides, for treatment purposes, into fines, nominally between 500 and 150 !tm, and ultrafines, nominally minus 150 !tm. Studies on processes for the treatment of minus 0,5 mm coal are discussed, and the lower size limit beneficiated is indicated for each process. The installation and operational results from a pilot froth-flotation plant treating minus 150!tm coal are described.

Jan 1, 1986

'Gee Whiz', a nationwide schools' science and technology competition, is being screened on SATY1 on Friday evenings at 18:00. Twenty-seven schools from al over South Africa are taking part in the series, which will run for 13 weeks. The participating schools were selected on the basis of their performance in the National Youth Science Olympiad and in Mintek's Minsa science competition, which has been organized on an annual basis since 1988.

Jan 1, 1991

The statistical methods described in the previous chapter permit the estimation of the average value p of a deposit, and the calculation of confidence limits for this value. They are based on the assumption of independence of sample values. As soon as a reasonable number of samples has been obtained from a deposit, local valuation, or estimation of blocks of ore within the mineral deposit, becomes necessary. The assumption of independence of values must then be rejected. Local valuation is possible only if there is a relationship between the value of a sample and the value of the surrounding ore, provided this relationship is a function of the position of the sample with respect to the blocks of ore to be valued. Whichever method is used for the valuation of a block of ore, the following assumptions are always made: ? The values of samples located near or inside the block are related to the value of the block. ? The values of the samples located closest to the block are most closely related to the value of the block. These assumptions will hold true only if the following assumption can also be made: ? There exists a relationship between sample values which is a function of the distance between samples. We are saying that the value x (z) of a sample centred at a point z has properties which are functions of this point. A certain spatial structure exists in the sample distribution. We are therefore dealing with a regionalized phenomenon, and we must treat x (z) as a regionalized variable. This can be done statistically by means of a model chosen to represent the spatial structure of the phenomenon. We shall see that the relationship between block values and sample values can be deduced from the relationship between sample values, and all local valuation problems can be solved using the statistical model obtained from the analysis of the sample values. It is important to realize that this statistical model is obtained by analysing the properties of known sample values, and will be used for the estimation of unknown block values. Such a statistical inference is valid only if the model developed represents the properties of both the sampled section of the ore body and the section to be valued: some stationarity conditions must be satisfied, and the model with the least restrictive conditions is preferred. In the following chapters, the most important models used in spatial geostatistics are presented. The models which can be used when there is no significant drift (trends) in values are described in Chapters 3-1 1. These models can also be used to solve some specific valuation problems when a linear drift is present. A general study of the more difficult problem of analysis of an ore body whose values present a drift is described in Chapter 12. Note that the area considered for local valuation of a block of ore is often small enough for any drift which might be present to be ignored.

Jan 1, 1978

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By E. Saari, B. Musuku, K. Jansson

The quality of the concentrator plant process water is crucial for high performing mineral flotation circuits. Significant metal recovery and concentrate grade losses have been noticed particularly in more closed water loops. The recovery and quality losses have started to emerge mainly with decreased freshwater usage and because of changes in tailings management towards tailings thickening, paste, or dry stacking. These changes result in shorter, closed water loops with a rapid build-up of harmful components with negative impact on the beneficiation process. Consequently, water quality has a direct link to decreased product value and sales returns. Complete cleaning or water blending might not be the right way to achieve high recovery and high-quality products. Instead, the key is to understand what kind of water qualities are needed for the flotation of specific minerals. In this study harmful substances in various plant water streams were removed and/or modified by pilot-scale dissolved air flotation. Batch-scale mineral flotation tests with the untreated and treated water were then performed by using fresh ore samples and the plant’s own laboratory flotation procedure. The results indicate that because of dissolved air flotation, the mineral flotation recoveries were enhanced by 1‒3.3%. Keywords: Mineral recovery, metal recovery, mineral quality, process water, concentrator, beneficiation, mineral processing, flotation, process water treatment

Jan 1, 2020

NIM reports Report No. 1615 Fluorspar pellets. A survey of the world market and an assessment of future South African production. Report No. 1621 Correction for matrix effects in the analysis of solutions by X-ray-fiuorescence spectrometry. Notices Questionnaire on Technicians The Department of National Education's committee of enquiry into the education, training, utilization, and status of engineering technicians in the Republic of South Africa was established as a result of Resolution 6.3 taken at the Sixth Conference on Engineering Education: The Education and Training of Engineering Technicians. Vraelys oor Tegnici Die Departement van Nasionale Opvoeding se komitee wat ondersoek instel na die opleiding, gebruik en status van ingenieurstegnici in die Republiek van Suid-Afrika is gestig as gevolg van Besluit 6.3 wat geneem is tydens die Sesde Konferensie oor Ingenieursopleiding: Die Opleiding van Ingenieurstegnici. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute.

Jan 8, 1974

By G. Akdogan, T. P. Kekana, Q. G. Reynolds

The DC arc plasma gasifier concept is currently under development at Mintek for testing the feasibility of producing syngas from waste coal fines and dry steam. The technology is intended for the valorisation of low-grade discard coals into market-quality syngas, which may then be used for largescale electrical power generation to address current grid supply challenges in South Africa. Other potential applications include feedstock for petro-chemical plants, fuel for transportation vehicles, domestic and industrial heating, and others. The proposed concept of a DC arc plasma gasifier was developed based on a plasma torch, metallurgical-based and entrained flow coal gasifiers. The principles of design and operation of the proposed gasifier are based on the concept of the Westinghouse Plasma Corporation (WPC) gasifier where the torches are substituted by graphite electrodes from which electric arc plasmas are generated. The DC section of the gasifier will be designed considering Mintek’s experience in the sealing of the furnace as carried out in the Mintek Thermal Magnesium Process. As part of the building blocks of a full conceptual design, the feasibility of the DC arc plasma gasifier was investigated through testing and modelling of its critical elements as proof of concept. The main activities of this work included pilot scale evaluation of the arc behaviour in the presence of dry steam, modelling of the temperature distribution within the reactor and explosibility studies on three different coal dust samples. Keywords: DC arc plasma gasifier, explosibility index, lower explosion limit, minimum ignition energy

Jan 1, 2020

By S. Annavarapu

"Fragment size distributions play an important part in the design and planning of block cave mining operations. Though several methods have been proposed for estimating fragment size distributions in advance of mining, the calibration of these estimating procedures to field measurements has been a challenge. The Block Size Estimator (BSE) program was developed for providing an assessment of primary fragmentation expected in a block cave mine using drill-core piece length data and joint characteristics from the exploration and geotechnical evaluation programmes. In order to validate the results from the BSE program, the drill-core piece length data and the joint characteristics in different rock types from the DOZ block cave mine in Indonesia were used to help generate fragment size distributions in different areas of the mine. The predicted fragment size distributions were compared with the fragmentation observed at the drawpoints during operation of the mine.This paper presents the details of the validation of the fragment size estimates by the BSE program using fragment size distribution data from the drawpoints at the extraction level at the DOZ block cave mine, and the challenges encountered in developing reasonable correlations between the estimated and measured fragment size distributions. IntroductionThe assessment of fragmentation is an important aspect of the design and planning of the block cave mining method, and forms an integral part of the design of the excavations at the extraction level and the selection of material handling systems for transporting the ore to the processing stations. Secondary blasting requirements can also be estimated based on the fragment size distributions developed for the block cave (Laubscher, 1994).Several methods of estimating fragment size distributions in block cave mines have been developed based on joint set parameters estimated from structural data from oriented core drilling campaigns and mapping of available excavations and outcrops. The BCF program (Esterhuizen, 1999) estimates the fragmentation using a combination of empirical, analytical, and rational methods to model the behaviour of materials during the primary and secondary fragmentation processes. The program JKFrag uses advanced tessellation of joint traces to create rock blocks and then generate fragment size distributions (Brown, 2002). Nickson, Coulson and Hussey (2000) presented the details of processing of the geotechnical data from the Mont Porphyre project, including an assessment of block sizes from the data collected on the core logging sheet. The distance between natural fractures was used to create distributions of block lengths, and a distribution of potential block sizes was estimated assuming that the blocks had equal dimensions in all directions. The results agreed closely with the results of the BCF program. Hadjigeorgiou, Grennon, and Nickson (2002) demonstrated the use of oriented borehole data to provide characteristic block size distributions for a mining project using a software package called Stereoblock, which generates a three-dimensional joint network for a given volume and calculates the volumes of blocks created by the intersections of these joints, simulated as circular planes. The distributions of joint orientation and joint spacing generated from statistical analysis of the oriented core data are used for the creation of the Stereoblock model. The diameter of the circular planes representing the joints is determined based on the mean and standard deviation of the joint trace length obtained from scan-line mapping."

May 1, 2019