Search Documents

By M. Borowski, N. Szlazak, D. Obracaj

Methods of research and control of the intensity of gas inflow to undersoil layers, after the mines were abandoned are presented in the paper. Gas migration causes them to penetrate to lower storeys of buildings and earthen structures being a menace to people's health and life. The results of measurements of gas concentration in undersoil layers, gas emission to atmosphere and their accumulation in buildings on the territory of closed down mines are presented.

Jan 1, 2003

By E. Keskinkilic

In this study, sulfide-type inclusion morphologies of a Ca-treated hot-rolled wheel steel, Grade-X, were investigated. The specimens taken from the hot-rolled products of Grade-X heats were studied. The size and distribution of elongated sulfide inclusions were examined for the heats of different S levels. Elongated sulfide inclusions were either not observed or rarely encountered when ladle analysis S content was below 50 ppm. The size and relative abundance of sulfide inclusions were reported to increase markedly when the S composition was greater than or equal to 70 ppm and the Ca/S ratio was less than 0.50. The effect of Ti addition (0.010?0.020% Ti) on sulfide-type inclusion morphologies was then investigated for heats having a sulfur content higher than 50 ppm. Addition of Ti was found to have a partial effect on decreasing the size of sulfide-type inclusions under real steelmaking conditions. Keywords Sulfide inclusions, Ca-treatment, titanium.

Jan 1, 2011

By E. D. Musin, S. S. Gudkov, A. V. Epiforov, S. V. Balikov

The standard technology for processing of gold-bearing sulfide raw material has many problems associated with the use of cyanide as a gold lixiviant. Therefore, many tests to find alternative gold recovery methods are being undertaken. This paper describes some technological solutions, which can become alternatives to cyanide technology in the future. Pressure oxidation (POX) of refractory gold-bearing sulfide concentrates from five different Russian gold deposits were investigated. Concentrate 1 was gold-copper concentrate. Concentrate 2 was gold-pyrite concentrate. Concentrates 3-5 were pyrite-arsenopyrite double refractory concentrates. The POX tests were at temperatures of 110, 200 and 220 °C and oxygen pressures of 1.5, 2.4 and 3.0 MPa were carried out. Gold lixiviants, such as chloride, thiosulfate, sulfite and thiocyanate were tested. The recovery of gold from sulfide gold-bearing concentrates by non-cyanide methods was 97- 99%, and from double refractory concentrates, 86-93%. The tested reagents are less toxic than cyanide, and their use will reduce of the cost of gold production. These methods make it possible to recover gold in acidic media, and eliminate the washing operation and POX slurry neutralisation. In addition, precious metals recovery from POX cakes using lead reduction smelting was investigated. It was shown that the “POX-pyrometallurgical” technology for double refractory concentrates processing could be used with recoveries of gold and silver of 97 and 96%, respectively. Keywords: Recovery of gold, refractory sulfide gold-bearing concentrates, double refractory concentrates, pressure oxidation, non-cyanide lixiviants of gold, chloride autoclave leaching, thiosulfate leaching, thiocyanate leaching, sulfite leaching, reduction smelting, POX-pyrometallurgical technology

Jan 1, 2020

By S. Moolla, R. Lynch, S. Brijraj

A reliable method to locate microseismic evets is an important objective for routine mine seismic monitoring. We developed an algorithm that can automatically and reliably locate an event from a single uniaxial trace. Signals created by microseismic events are recorded as seismograms that consist of direct P- and S-waves as well as the waves reflected off the underground excavations. We take advantage of the extra complexity these reflections introduce as they make the signal more unique. In our investigation we cross-correlated unaltered synthetic seismograms against trial waveforms created from a linear combination of appropriate waveforms from a library of numerically calculated strain Green’s tensors. We use a single uniaxial synthetic seismogram to invert for the source location, six moment tensor components, and frequency. The resulting cost functions are constructed as maximal correlations at each node in the mine grid through the true source x-planes. This function is maximized by differential evolution to simultaneously yield the source parameters. Sensitivity tests such as shifting the mine plans and altering the background velocities of the media are investigated to test the robustness of the method. We contaminate the data with 40% white noise to test the resolution against simulated real recorded seismograms. The method is demonstrated using synthetic data calculated with a realistic underground 3D velocity model.

Jun 10, 2024

By J. Saunders, N. Pretorius, G. Krafft, T. P. Katakwa

Imagine being able to see all the future planned mining activities in real time. This is exactly what SIMS (Short Interval Management System) will enable you to do. SIMS is a real time short interval control system that continuously measures and sets optimised plans for mining production processes. The system utilises algorithm-based software that takes resources (people, equipment, tasks, and workplaces) and gives you the best achievable plan. The algorithm was developed using methods found in the field of metaheuristics. A metaheuristic is a strategy to designed to efficiently search for optimal or near optimal solutions to problems that are very complex computationally. (Glover, 1986) There are several algorithms that have been developed to solve optimisation problems which are difficult to solve using traditional techniques. This has given rise to a field called evolutionary computing. (Simon, 2013) Examples of these techniques are genetic algorithms, particle swarm optimisation, and ant colony optimisation. These methods are used to solve problems in a variety of fields. As an example, Kok and Lane (2012) used particle swarm optimisation for equipment allocation in a mechanised underground mining environment. The first SIMS deployment took place in a platinum underground tabular mechanised mine near Burgersfort (province?) from 2017-2019. This included the development from a paper-based system to a fully operational online system. SIMS then moved to a second site and is currently being tested in a second platinum underground tabular mechanised mine in South Africa. Full deployment of the system is currently being phased in. SIMS was built in response to issues that have been plaguing the mining industry for years. These issues are all aligned into one major problem statement: how can we optimise mining production processes without compromising safety? This product was developed by combining years of mining experience with software development. SIMS is based on a four-pillar concept. Safety, productivity, accountability, and business improvement. SIMS uses a set of pre-configured mining and production rules, and with the resources that are available, to determine valid short term production plans. A background algorithm then determines the optimum plan to be executed. The system continuously produces a set of job cards that are pushed to respective operators on their allocated tablets. The management portal component allows you to view and manage all current and planned work on any connected device available. This allows real time visibility of completed, current, and planned work to operators, service departments and management, i.e., seeing into the future.

Sep 1, 2021

By A. F. Silva, J. M. G. Sotomayor, V. F. N. Torres

Geotechnical monitoring plays an important role in the detection of operational safety issues in the slopes of open pits. Currently, monitoring companies offer several solutions involving robust technologies that boast highly reliable data and the ability to control risky conditions. The monitoring data must be processed and analysed so as to allow the results to be used for several purposes, thereby providing information that can be used to manage operational actions and optimize mining plans or engineering projects. In this work we analysed monitoring data (pore pressure and displacement) and its correlation with the tension and displacement of the mass of an established failure slope calculated using the finite element method. To optimize the back-analysis, a Python language routine was developed using input data (point coordinates, parameter matrix, and critical section) to use software with the rock mass parameters (cohesion, friction angle, Young’s modulus, and Poisson’s ratio). For the back-analysis, the Mohr-Coulomb criterion was applied with the shear strength reduction technique to obtain the strength reduction factor. The results were consistent with both the measured displacements and the maximum deformation contours, revealing the possible failure mechanism, allowing the strength parameters to be calibrated according to the slope failure conditions, and providing information about the contribution of each variable (parameter) to the slope failure in the study area.

Oct 1, 2021

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluoridesl.2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02?SiO2) with the ammonium acid fluoride (NH4F?XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo-dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By X. Zhang, E. Li, Y. Xiao, Z. Yu, H. Han, J. Xie, J. Tian, W. Sun, K. Hong

In a pulp environment, the surface properties of magnesite and dolomite tend to be similar, due to the re-adsorption of dissolved calcium species, which makes the flotation separation difficult. In this paper, the chelating reagent EDTA is introduced to eliminate the adverse influence of the calcium species and to restore the selectivity of magnesite-dolomite separation using sodium hexametaphosphate (SHMP) as a depressant. Flotation experiments confirm that the recovery of magnesite improves significantly in the presence of EDTA. Zeta potential experiments confirm that the negatively charged EDTA4+ and HEDTA3+ species can form soluble and stable chelates with positively charged Ca2+ and Ca(OH)+ species preventing their adsorption on the magnesite surface. Adsorption measurements prove the addition of EDTA can decrease the adsorption of depressant SHMP on the magnesite surface. X-ray photoelectron spectroscopy (XPS) measurements further confirm the transformation from the surface of magnesite to dolomite in the presence of calcium ions, and the possible adsorption mechanism of EDTA and SHMP on the magnesite and dolomite surface. Key words: Magnesite; Dolomite; Surface dissolution; Flotation separation

Jan 1, 2020

Plurigaussian simulation allows constructing lithofacies or rock type models that reproduce the contacts between facies in accordance with the geologist?s interpretation. Its implementation requires inferring the local facies proportions, but the uncertainty in the true proportions is not accounted for. The simpler model with constant facies proportions may not yield realistic results, due to the possibility of obtaining facies at locations where it is geologically unlikely to find them. This article presents a variation of the plurigaussian model, in which the facies proportions are represented by random fields. The realizations can be made conditional to soft geological informati onto account for local changes in the facies proportions. The model is illustrated via a case study of a porphyry copper deposit where four Gaussian random fields are simulated conditionally to drill hole data and to constraints on the probability of finding a given facies at specific locations (control points) in the deposit. Then the first two fields are truncated using the random thresholds defined by the last two, generating a three-facies model. The proposed random proportion model proves to be simple to use and to account for spatial variations of the geological characteristics and for the uncertainty in the facies proportions. Keywords: categorical variable; lithofacies; truncated plurigaussian simulation; regionalized proportions

Jan 1, 2008

By V. Oberholzer

The presence of fines (particles smaller than 6 mm in diameter) causes hydrodynamic problems in gasifiers and therefore it is of great importance to minimize the amount of fine coal in the feed. This serves as motivation for understanding coal?s breakage mechanisms, which could lead to the ability to predict the generation of fines. The aim of this project was to simulate the pulsating effect of the conveyor belt in order to investigate factors influencing the breakage. Results indicated that an increased initial particle size had an increasing effect in the amount of fines generated. Weathering had an insignificant effect on the breakage of coal. To conclude, a breakage model was developed to describe the rate of breakage out of the top size when a combination of two breakage modes is present.

Jan 1, 2009

By P. Stefanek, N. Duda, B. Jachni, P. Stefaniak, B. Bursa

The Zelazny Most Tailings Storage Facility (TSF) is the largest reservoir of post–flotation tailings in Europe. The total amount of tailings from the mines in Lubin, Rudna, and Polkowice are stored each year at the disposal facility, which reaches approximately 30 million tons. It is crucial to accurately monitor and maintain such a huge storage facility, for the safety and economics of the entire region. In general, the monitoring network installed at the Zelazny Most TSF includes four groups of components: (a) geotechnical network (VW pore pressure transducers and inclinometers), (b) hydrological network (open piezometers, water level gauges, drainage discharge measurements, (c) geodetic survey network (e.g. surface and in-depth benchmarks, laser measurements, GPS measurements within GEOMOS network and (d) seismic network (e.g. accelerometer stations, cone penetration tests.) Apart from the above, chemical water analyses, tests of soil samples, monitoring of spigotting processes, and monitoring of relief wells’ discharge are also conducted. In total, approximately 2900 monitoring instruments are installed within the area of the Zelazny Most TSF. Such large amounts of data from the various information sources makes manual data analysis by the engineers almost impossible. In this paper we discuss a machine learning driven approach to improve the quality of the monitoring and maintenance of such facilities. We focus on the seismic cone penetration test (SCPT) data analysis. First, we carefully describe the collected data, its quality and availability. Then we discuss possible events that can occur in the TSF that need to be predicted using SCPT. Based on the information obtained in these two steps, the applicability of several machine learning methods is estimated. Some of them are then tested on available historical data. The algorithms described in this article will be further developed in the IlluMINEation project (H2020).

Sep 1, 2021

By G. Sahasrabudh, G. DeIulii, K. P. Galvin

A novel agglomeration process has been developed, utilising a concentrated water in oil emulsion as a binder. The binder is typically 95 wt% water, the remainder being an organic phase containing kerosene and the emulsifier— sorbitan mono oleate (SMO) in equal mass portions. The binder can selectively agglomerate hydrophobic particles in less than 7 seconds. The agglomeration has proven to be highly effective in recovering any particle of virtually any size, provided the particle is hydrophobic. The approach has previously been applied to coal, magnetite and silica. In the paper, sodium isobutyl xanthate (SIBX) and its much longer chain version, potassium tetradecyl xanthate (C14X), were used separately as collectors to selectively agglomerate chalcopyrite from the ore. Xanthates attach to metal sulphides, thus hydrophobising sulphide mineral particles. Chalcopyrite is a sulphide mineral; however, it hydrolyses quickly in the presence of water. Ethylenediaminetetraacetic acid (EDTA) was used to remove the oxide layer formed at the surface of the mineral particles after wet grinding, leaving behind a freshly generated metal sulphide surface. After the EDTA treatment, the ore particles were quickly conditioned at an optimised pH as well as collector concentration and agglomerated. The agglomeration achieved a copper recovery of 75% within 7 seconds, consistent with the recovery achieved by flotation over much longer time scales. Keywords: Chalcopyrite, agglomeration, froth flotation, interfacial chemistry, X-ray fluorescence, selective hydrophobisation

Jan 1, 2020

By J. van der Walt, W. Spiteri

Flyrock remains a significant threat to the health and safety of mine employees and integrity of infrastructure, as well as to the safety of the neighbouring communities and their property. This investigation was motivated by the general lack of fundamental research and mathematically quantifiable data in the literature regarding the relationship between blast design parameters and their impact on flyrock. The focus was to develop a concept that can be used to mathematically quantify the trajectory of flyrock resulting from a blast, which can be used for future research. The ultimate goal for this technique, once it has been fully developed, is to: ➤ Enable mining operations to generate a database with accurate historical flyrock measurements resulting from their blasting operations ➤ Allow research teams to conduct scientific investigations into flyrock and the impact of various blast design parameters ➤ Generate point-cloud data to visualize blasts and flyrock in a virtual reality environment for training and education purposes. This paper summarizes a conceptual technique and preliminary fieldwork that was carried out to determine the technique’s feasibility and motivate further development. The results show conclusively that a modified photogrammetric technique is capable of capturing flyrock data for further processing and analysis. The data acquisition procedure can, at this point, be used to meet the first aim of the project, namely to gather a field database of historical flyrock generation. Further development of the technique is ongoing and it is envisioned that the scientific-based technique will provide a method whereby future flyrock studies will be comparable and that assumptions will be limited.

Apr 5, 2023

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

By S. Blancher, A. Perroton, H Smith, T. Nzima, T. Wallmach, V. Dieudonné

Chromite beneficiation is generally performed by crushing and density separation using spirals. At the Dwarsrivier Chrome mine spiral efficiencies seam to vary, the reason for which is not evident. This sometimes results in the production of low-grade products, which are sold at relatively low prices. This paper represents a Qemscan® study that investigated mineralogical reasons for these variations. Variations in liberation of chromite particles as well as variations in chromite compositions were investigated. The results showed that the so-called low grade chromite product can be improved to become a high grade chromite product by means of a refinement in mineral processing. A detailed Qemscan® database (SIP file) was developed to account for variations in chromite chemistries. It can be shown that chemical variations with respect to Cr, Al, Mg and Fe in chromite particles reporting to the scavenger tails are larger than in the high grade product. A combination of these chemical variations together with a decrease in liberation of chromite particles in the scavenger tails can potentially help to recover more chromite particles from this specific process stream.

Sep 1, 2021

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1980. Mr D. A. Viljoen (President) was in the chair and declared the meeting open at 4.05 p.m. Obituaries President: It is my sad duty to announce the death of the following members of the Institute: T. C. A. Meyer (Past President, 1941 to 1942); E. G. Harding, T. A. Stannard, C. T. Hardy, W. C. Jackson, J. S. Sinton, G. H. Duggan, H. H. A. Muller (Life Fellows); W. M. Frames, K. Gebhard, W. M. Walker, S. L. S. Swart, N. W. Stansmore, H. E. Allen, B. W. F. Towne, R. A. Wilson, D. Waterman (Fellows), R. M. Peterson (Life Member); D. L. Gibbs (Member); B. M. Williams (Asso¬ciate Member); D. B. T. Cresswell, P. G. Guernier (Associates). As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments of silence. Notules President: Kan ons die notules van die Algemene Jaar¬vergadering, wat op 22 Augustus 1979 gehou was en in die September uitgawe van ons Joernaal gepubliseer is, bevestig? Bevestig.

Jan 1, 1980

By J. A. Venter, M. K. G. Vermaak, J. G. Bruwer

Electrostatic separation is employed in the concentration of zircon and rutile. The zircon concentrate undergoes an acid treatment to remove impurities from the surface of both the zircon and rutile. The purpose of the acid treatment is to increase the difference in the resistivities of the two minerals, thus ensuring the best possible electrostatic separation efficiencies. Previous test work suggested that these impurities are not removed, but only modified; the surface modification seemed more prevalent in the case of the rutile. The resistivity of the rutile changes with pH and thus the electrostatic separation of the rutile is influenced. X-ray photoelectron spectroscopy (XPS) indicates that there is an increase in the OH and adsorbed H2O concentrations on the rutile surface. XPS also showed significant differential charging on the rutile surface, which indicates that the species on the rutile surface have different resistivities. The zircon particles from the conducting and non-conducting streams have similar resistivities and no major differences in their surface species. Zircon losses during the final electrostatic separation appear not to be due to surface effects, but due to shielding of particles during the separation.

Jan 1, 2007

By I. J. Kotzé, R. T. Jones

Conventional PGM matte smelting requires the presence of a certain quantity of base metal sulphides in order to collect the platinum group metals in a molten sulphidic matte phase in the furnace. Furthermore, the quantity of chromium oxide in the feed materials is controlled in order to avoid the build-up of high-melting chromite spinels in the furnace. Mintek has developed a process for smelting difficult PGM-containing feed materials that contain low amounts of sulphur and/or high amounts of chromium oxide. A DC arc furnace is used to provide the appropriate conditions to generate an iron alloy that collects PGMs very effectively, leaving extremely low residual quantities of PGMs in the slag. Various feed materials have been treated successfully in furnace campaigns running at power levels up to 1.5 MW. The longest of these campaigns was run continuously for more than four months, treating more than two thousand tons of materials such as low-grade concentrates, revert tailings, and converter slag. The campaigns demonstrated the robustness and versatility of the process, and proved that it is possible to sustainably produce a PGM-containing alloy and discardable slags containing an average of less than 1.4 g/t of PGMs over the entire campaign. Keywords: DC arc, smelting, furnace, platinum, PGM, revert tailings, converter slag, ConRoast

Jan 1, 2004

By G. T. G. Emere

The Johannesburg Branch of The South African Institute of Mining and Metallurgy was officially inaugurated at a General Meeting held in Kelvin House on Monday, 18th January, 1988. In addition to nominating committee members, Mr G. T.G. Emere delivered a presentation on the Barbrook gold-mining project, which is currently in the development phase some 40 km east of Barberton.

Jan 1, 1988