Search Documents

The treatment of gold-plant tailings with ferrous sulphate to remove the cyanide is currently in use, on several gold plants. In some cases there is scope for optimization the process. The present work provides a detailed study of the reaction between cyanide and ferrous sulphate. Optimal conditions for the removal of total cyande required a ph of 5,.5 to 6,5 and an Fe:CN molar ratio of 0,5. Ferrocyanide ion is shown to be unstable In aqueous acidic solution, with rapid oxidation to ferricyanide, (Fe(CN) 6 ), and formation .of Fe(CN)5H2O3- at pH values below 4, The precipitate from the reaction between cyanide and ferrous sulphate consists mainly 01 Insoluble Prussian blue, Fe4[Fe(CNI&!.3,and IS shown to be unstable in the presence of alkaline solution, since it decomposes rapidly at pH values above 7 to form ferrocyanide, (Fe(CN)6 ), in solution and various insoluble iron oxides,

Jan 1, 1992

By E. Maritz

"The localized uniform conditioning (LUC) technique was proposed by Marat Abzalov in 2006. The technique converts conventional uniform conditioning (UC) grade-tonnage curves into single grade values attached to each smallest mining unit (SMU). This is achieved by ranking the SMUs within a panel in increasing order of their grade (based on the direct kriging of SMUs). This ranking is then used to localize the conventional UC grade-tonnage curves for each panel by dividing them into classes and computing their mean grades, which are assigned to the SMUs. The quality of this localization process will depend heavily on the validity of the grade patterns predicted by the direct kriging of the SMUs. Abzalov noted that where the distribution of data available for the direct kriging of the SMU is characterized by strong short-range variability, the advantages of using the LUC approach may be more limited. Consequently, a study was undertaken to determine how valid the predicted grade patterns of a typical Birimian-style gold deposit (with high nugget effect and strong short-range variability) might be expected to be. This was determined by comparing the direct SMU kriging ranking (based on sparse data) with the grade control model ranking (based on close-spaced data and the best available estimate of the deposit). The results showed a satisfactory correlation between these rankings and it was concluded that, although the grade patterns predicted by the direct kriging of the SMUs may be less meaningful for deposits exhibiting strong short-range continuity, there is nevertheless a convincing relationship with the actual (or best available) rankings. Therefore, the LUC technique is still considered to be useful for this style of deposit. IntroductionFor adequate technical and financial evaluation of a project, attempts should be made to estimate the recoverable resources – the portion of the in situ resource that can be economically extracted by mining. To achieve this, the estimates of the tonnage and grade of the mineralization should be produced above a given economic cut-off and should take into consideration the proposed mining selectivity."

Jan 1, 2016

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

[Consider a square block W in an ore body S2, to be valued from one centre sample w, and one corner sample w2 (Fig. 9.1). The sample set is ws = Iw,;w21. We can estimate the block average µw by the average of the sample values x, and x2: µw = 'z (x, + xz). (9.1) The error made is measured by the estimation variance: o' (ws to W) = 2 - (ws; W) - - (ws;ws) - - (W; W). (9.2) However, we know that the centre sample w, gives more information about the block value than the corner sample w2. In the example studied in § 8.4, where w, and w2 were considered to be points, we found that of (w, to W) was nearly one third smaller than o2E (w2 to W), therefore when estimating W one should give more weight to w, than to w2. In general, when evaluating a block W from a set of n samples ws, where WS = l w;w2; ... wn1, a better estimator of µw can be obtained if we give different weights to the sample values, depending on the size and the positions of the samples. Some desirable properties of such an estimator µw are: ? It should be a linear function of the sample values xi: n µw = bi xi (9.3) =t where bi = weight given to sample x . ? It should be unbiased, i.e. its expected value should be equal to the true block value: E [µw - µw] = 0. (9.4) ? The mean squared error of estimation of µw should be a minimum E [(µw - µw)2] = a minimum. (9.5) The estimator which satisfies these properties is a minimum variance, linear and unbiased estimator, and is known as the kriging estimator. The corresponding error of estimation is the kriging error. This estimator is also known as the BLUE (for Best Linear Unbiased Estimator) estimator. This was named by Matheron in acknowledgement of the early work of Krige's in the optimization of the evaluation of the South African gold mines. The following notations will be used: µK kriging estimator. o2k = o2K (w,, to W) kriging error.]

Jan 1, 1978

By M J. Daniel

The diamond industry is no newcomer to High Pressure Grinding Rolls (HPGR) as it has used the technology for more than 20 years, predominantly in secondary crushing and recrushing roles. In fact it could be argued that the diamond industry has led the way for the wider minerals industry to consider its application. In existing conventional secondary cone crushing applications, large valuable diamonds are" won" through meticulously managing the recovery process within defined particle size ranges. Conventional crushers operate with relatively large closed side settings, but have the potential to damage diamonds by making direct contact with the sides of the crusher. Cone crushers also result in steep product size distributions that run a high risk of losing many of the smaller, unliberated but more abundant diamonds from the rock. This current comminution paradigm of particle size reduction management results in recrushing processing applications or plants where HPGRs are often used.

Jan 1, 2010

The September General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th September, 1970, at 3.00 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present one hundred and eighteen Fellows, including Dr J. M. Bereza, H. P. Carlisle, R. J. C. Goode, Dr J. P. Hugo, P. Lambooy, Prof R. P. Plewman, W. W. Malan, Dr J. T. McIntyre, Dr M. D. G. Salamon, L. W. P. Van den Bosch, P. A. von Wielligh (Council Members), A. Bain, G. P. Bennet, D. L. Carson, G. L. H. Diering, M. E. E. Douglas, F. A. B. Fouche, R. Fourie, A. R. C. Fowler, E. B. Gordon, J. S. Hay, G. H. Henderson, S. D. Hill, A. C. Hofmeyr, J. M. Jacobs, A. F. Lee, D. G. Malan, L. J. Prince, W. G. Pyne-Mercier, A. H. Mokken, Dr W. S. Rapson, R. R. Richardson, H. V. Solomon, C. G. Sowry, G. G. Stanley, G. R. Still, D. L. Starkey, D. L. Taylor, E. W. Thiel, I. E. Van Aswegan, M. van Ryneve1d Steyn, N. B. Vinson, H. Wheeler, Dr A. Whillier, R. A .Wilson, C. F. Ziervogel. Forty-two Members including R. C. Bertram, F. Collier, G. C. Currie, O. Davel, J. M. Gosnell, A. Hazell, Dr N. C. Joughin, F. Kleinschmidt, D. Love, R. B. Macgillivray, D. Mather, R. D. R. Munro, R. S. Pearson, J. J. Peisl, T. J. Pole, A. J. Rossouw, R. G. B. Skirving, G. S. Schwartz, K. Stee1e, H. A. G. Slater, A. Taylor, B. A. Thomas, P. L. Vaughan, D. T. Watt, W. Wilson. Nineteen Associates including R. K. Briggs, S. I. Du Preez, P. G. Gaylard, P. H. Hartslief, W. M. Mackay, A. D. Ross. Three Students: V. S. Care, R. J. Drummond, P. J. Pretorius. Thirty-one Visitors including C. P. S. Barnard, D. W. Bosch, M. Bain G. L. Brown, G. D. Behrens, C. Coetzer, D. M. Gilbart-Smith, R. L. Man, Dr G. J. Stander, M. W. L. Steinobel, R. H. E. Thorpe, T. D. van Wyk, P. H. van Zyl, E. Vereecken, J. J. H. Viljoen. Secretary, D. C. Visser. Total present: 215. OBITUARIES The President: "It is my sad duty to announce the death of the following: Bruce Donaldson Crawford, Fellow, who joined the Institute in 1951 and passed away on 29th April, 1970. Donald Joseph Powrie, Life Fellow, who joined the Institute in 1935 and passed away on 22nd July, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Associate: WiIliam Norman Carter. Students: Roman Michael Dabrowski, Sean George Dean Eaton, Alan Philip Stonham Howard, Anton du Preez Roos, Richard Harold Tourle. MEMBERS TRANSFERRED TO A HIGHER GRADE From Graduate to Member: Terrance Alexander Ward. From Associate to Member: Bernard Andre Thomas. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade." CO-OPTION The President: "I wish to advise members that, in terms of clause 3.9 of the Constitution, Mc. H. P. Carlisle had been co-opted to serve on Council." PAPERS FOR PRESENTATION The President: "We have two papers today, and I am first going to call on Dr Stander the Head of the Water Division of the C.S.I.R., who IS well known to many of you for his work and talks on pollution, who has had more than a little to do with this industry, and who has been I would say, of the greatest possible assistance to the mining industry in overcoming the problems of pollution which are so prevalent in industry of this nature. He, Mr Henzen and Mr Funke have written this paper, 'The disposal of polluted effluents from mining, metallurgical and metal-finishing industries, their effects on receiving water and remedial measures.' This is the Water Year, as you know, and it is most appropriate that we should have such an authority to talk to us on this very important topic. I now have much pleasure in asking Dr Stander to introduce his paper." After the presentation of the paper the President said, "Gentlemen, I am sure that you would like me on your behalf, to thank Dr Stander very sincerely for a paper which I think has enabled us to get a completely new slant on the Water Year. There are many people who have put their finger on this campaign and said, it is all a gimmick. There are others-I suppose notably some of the bridge clubs which operate on week-day afternoons in Parkview-who seem to think that this is a quick way of getting early rain. Of course, it is not. This is a most important paper which we have had given to us this afternoon. You probably found it here when you arrived and have not read it-I was very lucky to be able to read it last night, and there is an awful lot of meat in it. For as long as I have been associated with mining in any way, there has been a problem of polluted effluent-of effluents carrying a mineral load from mining, and I think Dr Stander is absolutely right-and, of course, the Commission is right when they say that this is not merely the problem of mine management or mine owners-this is a problem which affects every single human being in this country.

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

By S. Tshikhudo

This paper outlines an investigation into the recovery of saleable fractions of coal from ?as-arising? South Export Plant effluent streams, using Baleen microscreening technology. South Export Plant, a subdivision of BHP Billiton Energy Coal SA (BECSA) Coal Processing, is a two-module plant treating 2000 t/h. The nominally -150 µm coal is untreated and is therefore passed from classifying cyclones to the thickeners for process water recovery. The thickened underflow is pumped into a series of slurry cells for further settling and recovery of supernatant water. The marginal quality, moisture content, and handlebility of this settled material renders it unsuitable for inclusion into saleable products and it is thus stockpiled and trucked to designated pits for disposal. Over the years, stockpiling and trucking has become an overly expensive exercise. In an effort to recover some of this cost, a task team was assigned to investigate less costly options to process slurry across BECSA plants. Various technologies such as froth flotation, sieve bends, and Reflux Classifier were considered, although the results were generally not beneficial ? this could be attributed to weathered/oxidized coal. A decision was made to pursue an alternative approach by testing the suitability of the new ?Baleen Filter?. The concept is to screen out the higher-grade fraction (+50 µm) as saleable product and reject the finer fractions to the slurry ponds. The Baleen Filter was found to effectively screen at an acceptable efficiency between 94% and 99.99%, with a very sharp cut-point (d50 and Ep). The actual yields from the screening results were better than the predicted yields in terms of both mass and energy as predicted from feedstock analysis.

Jan 1, 2014

By L. Robles-Stefoni

"Multiple-point simulation (MPS) methods have been developed over the last decade as a means of reproducing complex geological patterns while generating stochastic simulations. Some geological spatial configurations are complex, such as the spatial geometries and patterns of diamondbearing kimberlite pipes and their internal facies controlling diamond quality and distribution.Two MPS methods were tested for modelling the geology of a diamond pipe located at the Ekati mine, NT, Canada. These are the single normal equation simulation algorithm SNESIM, which captures different patterns from a training image (TI), and the filter simulation algorithm FILTERSIM, which classifies the patterns founded on the TI. Both methods were tested in the stochastic simulation of a four-category geology model: crater, diatreme, xenoliths, and host rock. Soft information about the location of host rock was also used. The validation of the simulation results shows a reasonable reproduction of the geometry and data proportions for all geological units considered; the validation of spatial statistics, however, shows that although simulated realizations from both methods reasonably reproduce the fourth-order spatial statistics of the TI, they do not reproduce well the same spatial statistics of the available data (when this differs from the TI). An interesting observation is that SNESIM better imitated the shape of the pipe, while FILTERSIM yielded a better reproduction of the xenolith bodies. IntroductionThe simulation of geological units poses several technical problems that challenge the capabilities of available geostatistical simulation approaches and their ability to deal with spatial complexity of categorical variables. The spatial geometry of diamondbearing pipes and their internal facies controlling diamond distributions are a specific and well-known difficult modelling problem. The geometry of a kimberlite pipe is typically like an inverted cone (Figure 1); the wider part is known as the crater and is located near the surface, and the narrower, deeper part is known as the diatreme. Xenolith bodies can also be found inside the pipe. A very important contribution to the geological modelling of the contours of the pipe is the measure of uncertainty about the location of the contact between the kimberlite pipe and the host rock."

Jan 1, 2016

"Chairman: Mr W. S. GALLAGHERRapporteur: Professor A. M. STARFIELDPapers:Long-term mine production scheduling by G. C. S. BurneAn application of linear programming to investment analysis by A. ErlandssonOptimizing medium-term operational plans for a group of copper mines by M. Splaine, D. C. Atkinson, W. Davison and L. SmithThe simulation of underground stoping and transport operations in gold mining by F. H. Touwen and N. C. JoughinProduction planning is a subject that lies at the interface between the computing centre and mine management. Discus¬sion during this session was thus largely concerned, directly or indirectly, with communication between computing and mining personnel, and as such was relevant to the symposium as a whole.Mr A. Weiss set the tone of this discussion by referring to `user-orientated systems'. He congratulated Mr Burne in this regard, pointing out that his long-term production scheduling program, as a computer system, was similar in approach to the manual system it replaced, and was therefore easily understood by planning engineers. He asked whether the schedule engineer had his 'hands on' the system, to which Mr Burne replied that the engineer did in fact spend several days running alternative schemes through the computer. Mr Weiss commented on the advantage of having terminals on site for this sort of engineer-computer interaction. He also commented on the flexibility of Mr Burne's approach to scheduling and how preferable this was to a one-step optimization package. This was brought home by a question from Mr H. D. Small: Mr Burne's program sometimes found it necessary to temporarily halt an advancing face, and he asked whether the logic of the program could be altered to avoid this (e.g. by suitably slowing down the rate of face advance). Mr Burne replied that it was in fact easier for the planning engineer to sort this problem out manually. The way in which the computer results were presented made it particularly simple for the production engineer to see how to avoid or remedy a stopped face.On the technical side, both Mr Weiss and Mr H. M. Wells questioned Mr Burne on the handling of grade control by his program. From answers by Mr Burne and his colleague Mr K. H. Thomson it emerged that a spot-check on grade every now and then was all that was necessary at Mufulira, and that the idea of actual grade control was more a question of short-term than of long-term planning."

Jan 1, 2014

A mineralogical study was conducted on the feed (3.51 g/t Au and ~90 g/t Ag) and four leach residue samples (assaying 0.09 to 0.19 g/t Au and 30.0 to 61.5 g/t Ag) from the Pinos Altos silver-gold deposit in Mexico to determine the cause for gold and silver losses. A comprehensive mineralogical and analytical approach including fire assay, gravity pre-concentration, ore microscopy, mineral liberation analyser (MLA) and electron microprobe was used for the current study. Results showed that gold and silver lost in the leach residues occurred mainly as inclusions in quartz and silicates (accounting for over 80% for Au and 92% for Ag of the head assays, respectively), with a minor amount in iron oxide and other minerals. The amount of liberated gold and silver is negligible. Results also showed that gold and silver particles in leach residues are mainly ranged from 1 µm to 5 µm in size, which implies that ultrafine grinding is required to improve the recoveries of these two metals. Keywords: mineralogy, gold deportment, silver deportment, silver-gold ore, leach residue, recovery improvement.

Jan 1, 2009

If you have problems or questions relating to the installation of this disc, please either telephone Document Transformation Technologies at (+27 12) 667 2074, or e-mail: nigel@doctech.co.za Si vous avez des problèmes relatifs àl?installation de ce disque, veuillez appeler Document Transformation Technologies au (+27 12) 667 2074, ou nous écrire par courrier électronique: nigel@doctech.co.za Produced by: / Produitpar:Document Transformation TechnologiesP O Box 560 ?Irene ?0062 ?South Africa.Tel: (012) 667 2074; Fax: (012) 667 2766; International Code (+27 12) e-mail: doctech@doctech.com website: http://www.doctech.co.za

Jan 1, 2004

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

O.F.S. Branch Proceedings of the Annual General Meeting Held on Wednesday, 4th August, 1976 Mr G. J. C. Young (Chairman) was in the Chair. Also present was Dr R. E. Robinson, President of the South African Institute of Mining and Metallurgy. NlM reports Report no. 175 Copper extraction by leaching magnetites from Palabora Mining Company. (12th Apr., 1967; re-issued Jun. 1976) Report no. 1632 A mineralogical examination of beach-sand concentrates from a pilot plant at Richards Bay. (20th May, 1974; re-issued Jun. 1976.) Report no. 1825 The full automation of a Philips 1220 X -ray spectrometer. A Philips 1220 X-ray spectrometer (semi-automatic) Report no. 1840 The spectrophotometric determination of total uranium in silicate ores and leach liquors by use of bromo-PADAP. Report no. 1841 The determination of aC1;d-soluble uramum in silicate ores and solutions. AS & TS National Award The Associated Scientific and Technical Societies of South Africa has decided to make two National Awards this year. These awards, given in recognition of outstanding contributions to science and the application of science, will be made to Dr T. L. Wadley for his invention of the Tellurometer system of distance measurement and to Mr H. Scheffel for his design of the High Stability Bogie. Treatment of waste water A major international symposium, organized jointly by the Water and Environment Group of the Society of Chemical Industry and the Environment Group of The Chemical Society of London, will be held in London in 1977. Down-the-hole drilling Atlas Copco announces the publication of a revised and enlarged version of one of the booklets in their series 'Mining and Construction Methods'. This 40-page booklet is entitled 'Down-the-hole drilling with COP drills'.

Jan 10, 1976

By F. Botha

South Africa is amongst the 40 driest counties in the world, with extreme weather conditions and beset by both droughts and floods. Coupled with economic growth is an increased demand on water resources and, as with all other industrial developments, mining requires large volumes of water, which is likely to have an impact on the environment. Further to this, the mining industry also realizes that minerals are a non-renewable resource and the contribution to wealth creation from mineral extraction is not everlasting. It serves as an economic boost and careful planning is required to ensure that the legacy of mining is sustainable, and that some of the returns from mining provide continual economic and social prosperity.

Jan 1, 2012

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

By S. C. Maji, U. S. Chattopadyay, S. Chaudhuri, T. Gouri Charan

India is devoid of coking coal resources, which is a vital raw material for coke making. As a result it has to import about 80% coking coal for steel making. Indian National Steel Policy, 2017 has envisaged crude steel production around 300 million tonnes Mt) by the year 2030-31 and forecasts coking coal demand of 161 Mtpa (million tonnes per annum). One way of improving the indigenous resources is to study the performance of existing washeries and to improve the clean coal recovery by adopting suitable technology. A study was carried out, mainly to focus on the fine coal circuit of an existing coking coal washery, to generate the desired quality of clean coal. The operating coking coal washery being studied is presently feeding coal from nine different sources with varying feed ash contents. The coal fines varied in ash content ranging from 19.5% - 43.6%. For treating the coal fines, the washery has operated a spiral for the past few years. Performance studies were carried out, and it was found that the spiral is not efficient in recovering the cleans. Detailed investigations were carried out on the coal fines using flotation techniques, and it was found that to achieve a low ash clean coal, the froth flotation is a much better beneficiation option than a spiral, The studies showed that the recovery of clean coal through a spiral is 67.7% at ash content of 27.0%, while flotation tests showed a recovery of 68.1% at 16.5% ash content. Keywords: Coking coal washery, near gravity material, spiral washer, froth flotation

Jan 1, 2020

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

1. New books Australian Institute of International Affairs. Uranium - energy source of the future? Canberra, thelnstitute (Box E181, P.O., Canberra, A.C.T. 2600, Australia), 1979. 202 pp. A$4,95 (postage 50c). Euroeconomics. The steel industry in Western Europe.. industrial and financial indicators. Paris, Eurofinance (9 Avenue Hoche, 75008 Paris, France), 1979. 167 pp. FF4,500 (Available in English and French.) M. B. Piggott. Load-bearing composite materials. Oxford, Pergamon Press, 1979. $15,00. J. H. E. Olaf. Automation and remote monitoring and control in mines. Essen (West Germany), Verlag Gliickauf GmbH, 1979. 200 pp. DM36. (In English.) J. P. Jenkins and E. T. Brown (eds). KWIC index of rock mechanics literature. Oxford, Pergamon, 1979. 742 pp. £60. R. J. Wakeman (ed.). Progress in filtration and separation 1. Amsterdam, Elsevier, 1979. 346 pp. Dfl.llO,OO. 2. New journal As from 1980, Coal Calendar is being published as a separate monthly periodical. 3. Proceedings L. E. St Pierre and G. R. Brown (eds). Future sources of organic raw materials. Oxford, Pergamon, 1979. 612 pp. £22,50. P. Haasen, V. Gerold, and G. Kostorz (eds). Strength of metals and alloys. Oxford, Pergamon, 1979. 3 vols., 1800 pp. $200. K. J. Miller and R. F. Smith (eds). Mechanical behaviour of materials. Oxford, Pergamon, 1979. 3 vols., 1800 pp. U.S.$200. 4. Tax relief? The Publishers' Association of Great Britain recently issued a circular to a number of professional bodies drawing their attention to a court decision in favour of tax allowances on the purchase of textbooks. In January Electroheat The International Union for Electroheat, which com. prises a score of highly industrialized countries, every four years organizes a congress at which experts discuss the technicalities and economics of the latest applications of electroheat in industry and other sectors. Corrigenda: March issue The following amendments should be made to Table II of the paper 'Commodity analysis:

Jan 1, 1980

By J. F. Lupo

One of the earliest records of metal recovery by solution leaching is described by Agricola as 'juice of rock' in the 1550s. In these early years of hydrometallurgy and civil engineering, few controls and systems were employed to enhance recovery and protect the environment. Since that time, leaching (dump or heap) operations have made significant strides in increasing metal and solution recovery while protecting the environment, all goals of a sustainable operation. It is now recognized that the design and operation of modern heap leach facilities requires contributions from many fields of study, including hydrometallurgy, civil engineering, geotechnical engineering, unsaturated-flow hydrology, mine planning, geosynthetics engineering, geochemistry, process engineering, mechanical engineering, and electrical engineering. While advancements in these fields have resulted in more sustainable heap leach operations, challenges in the industry still exist. A number of heap leach operations exhibit poor or lower-than-predicted metal recovery, loss of solution flow and control within the ore heap, loss of ore heap stability under leach, failure of liner and/or solution recovery systems, and overtopping of process water ponds. A number of these issues may be the result of several compounding conditions. For example, poor metal recovery may be due to an inadequate scale-up assumption (scaling laboratory tests to field-size heaps), lack of control of the in-heap geochemical environment, changes in ore mineralogy from the original design, changes in mechanical and hydraulic properties of the ore from the original design, ore handling and pre-treatment, inadequate solution management system, and inadequate solution application. The purpose of this paper is to present and discuss issues that may affect the sustainability of a heap leach operation. Since sustainability encompasses a broad range of topics and issues, the focus of this paper will be on issues affecting metal and solution recovery, solution flow and containment, and stability of the ore heap.

Jan 1, 2012